Tender For Replacement Of Water Pipeline For External Water Supply Under Ge Ranchi
Tender Value
5.91 Crore
Estimated cost
Bid Submission
14 Dec 2026
28 days left
EMD
6.21 Lakhs
Bank guarantee accepted
Document Fee
3000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ranchi → Jharkhand
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Replacement Of Water Pipeline For External Water Supply Under Ge Ranchi
BOQ
| Sl. No. | Item Description |
| 1 | NOTE (Applicable for all items) :-(i) The bidders/contractors are advised to read tender document & all corrigendum / amendments and General conditions of contracts before entrying/quoting the rates.2. It is highlighted that the certain condition of General Condition of Contracts (IAFW-2249) has been modified as per direction of MoD i.e. inclusssion of Performance Security, deletion of Risk & Cost Provisions and increase in defect liability period all as per tender documents. The tenderers should keep in mind while quoting their offer. |
| 2 | Material and Labour for excavation in tranches in soil not exceeding 1.5mtr wide and not exceeding 1.5 mtr in depth for laying of pipes in tranches and getting out including levelling complted all as specified and directed. |
| 3 | Material and Labour for returning filling in including spearing levelling, waering and well ramming in layers not exceeding 25 cm thick each excavated soft/hard soil in trenches after the pipes have been laid and tested competed all as specified and directed. |
| 4 | Material and Labour for removing surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed by Engr-in-Charge |
| 5 | Cutting the existing road of any kind straight by manual, depth and width not less than 80 cm for pipes up to 350 mm dia and filling back with excavated soil up to 75% road portion and 25 % shall be made with cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate complete all as specified and directed. |
| 6 | M&L for road crossing/ drain crossing by adopting trench less tunnelling work through specified pipe jacking method by erecting the equipment to true to the alignment and gradient by hydraulic pipe jacking technique complete including tunnelling, excavation in any type of soils including hard rock, TO CROSS WATER PIPE LINE UP TO 200 mm dia in any length including jointing materials and necessary conveyance charges of machinery and other required materials in co-ordination with the concerned authorities complete all as specified and as directed INCLUDING MAKING GOOD OF DISTURBED SURFACE.NOTE: Pipe will be measured and paid separately under relevant items. |
| 7 | M&L for PCC 1:4:8 D2 using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed. |
| 8 | M&L for precast cement concrete block masonary in 1:3:6 type C1 using 20 mm graded stone aggregate with solid block exc. 10 cm width and setting in CM 1:6 complete all as specified and directed. |
| 9 | M &L for Brickwork with fly ash modular bricks, strainght or curved on plan exc 6M mean radious radius built in Cement mortar 1:6 complete all as specified and directed. |
| 10 | M&L for replacement of existing water level indicator in UG Sump/Semi UG Sump of any size , capacity and height by Float and board types level Guage using rope, ball valve, pully, necessary support , PCC , display board , indicator/ pointer , necessary painting and numbering complete all as required for proper functioning of level indicator complete all as specified and directed. |
| 11 | M&L for replacement of existing water level indicator OHT of any size , capacity and height by Float and board types level Guage using rope, ball valve, pully, necessary support , PCC , display board , indicator/ pointer , necessary painting and numbering complete all as required for proper functioning of level indicator complete all as specified and directed. |
| 12 | Supply, installation, testing and commissioning of Solar LED-based Aviation Obstruction Light suitable for mounting on overhead water tank, of 10 Watt (low-intensity Type-A) , complete with high-brightness red LED beacon, UV-resistant polycarbonate/glass dome, weatherproof corrosion-resistant housing (minimum IP-65 protection), integrated LED driver, surge protection device, and heavy-duty mounting bracket. The unit shall operate on 230 Volts single-phase AC supply, and shall conform to relevant DGCA/ICAO guidelines for low-intensity obstruction lighting. Work includes all necessary wiring using suitable copper conductor cable, providing PVC /flexible conduit, clamps, fasteners, earthing connections and testing on completion, complete all as specified and directed. |
| 13 | Taking up (dismantling and removing) existing cast iron (CI) water mains, including all associated fittings such as bends, tees, reducers, collars, specials, etc., having spigot and socket ends or flanged joints, including burning out / cutting and removing existing lead joints from spigot and socket connections and dismantling of flanged joints, complete all as specified and directed by Engr-in-charge, of following sizes:-Note :- Taking down of the existing pipe and laying, jointing, and connecting of the new pipe shall be carried out simultaneously on the same day to ensure uninterrupted and continuous water supply. |
| 14 | All as per Srl items No.12.00 here-in-before but of size 350 mm dia |
| 15 | All as per Srl items No.12.00 here-in-before but of size 200 mm dia |
| 16 | All as per Srl items No.12.00 here-in-before but of size 150 mm dia |
| 17 | All as per Srl items No.12.00 here-in-before but of size 100 mm dia |
| 18 | All as per Srl items No.12.00 here-in-before but of size 80 mm dia |
| 19 | Supply, laying, jointing, fixing, testing and commissioning of Ductile Iron (DI) pipes, spigot and socket (S/S) ends, Class K-9, conforming to IS:8329 / ISO:2531, complete, pipes shall be laid in trenches or in open execution, as directed at site, lowering, aligning, jointing using rubber gasket (push-on joint) or approved jointing material, including cutting of pipes, deflection at joints where required, and thrust blocks / anchor blocks wherever necessary, includes hydrostatic pressure testing, and making good disturbed surfaces, complete all as specified and as directed by the Engineer-in-Charge of following sizes of pipes.Note :- Necessary earth and PCC/Brick work will be measured and paid seperately |
| 20 | All as per Srl items No.18.00 here-in-before but of size 350 mm dia |
| 21 | All as per Srl items No.18.00 here-in-before but of size 200 mm dia |
| 22 | All as per Srl items No.18.00 here-in-before but of size 150 mm dia |
| 23 | All as per Srl items No.18.00 here-in-before but of size 100 mm dia |
| 24 | All as per Srl items No.18.00 here-in-before but of size 80 mm dia |
| 25 | Taking down (dismantling and removing) existing steel tubing and associated pipeline connections, including all fittings such as elbows, tees, reducers, collars, flanges, unions, valves, etc., having spigot and socket ends, of the specified size:-Note :- (i) Taking down of the existing pipe and laying, jointing, and connecting of the new pipe shall be carried out simultaneously on the same day to ensure uninterrupted and continuous water supply. |
| 26 | All as per Srl items No.24 here-in-before but of size 50 mm dia |
| 27 | All as per Srl items No.24 here-in-before but of size 40 mm dia |
| 28 | All as per Srl items No.24 here-in-before but of size 25 mm dia |
| 29 | Supply, laying, jointing, fixing, testing and commissioning of galvanized mild steel (GI) pipes, Medium class, conforming to IS:1239 (Part-1), including all GI fittings such as elbows, bends, tees, reducers, sockets, unions, nipples, caps, plugs, etc., complete, pipes shall be laid in trenches, walls, floors or ceilings, either concealed or exposed (open execution), as directed at site, including cutting, threading, jointing with approved jointing compound (white lead / PTFE tape), fixing with clamps, hooks, brackets, hangers and supports, and making all joints leak-proof, making good all disturbed surfaces, pressure testing of the pipeline, flushing and commissioning, including all labour, materials, tools, scaffolding and accessories, complete all as specified and as directed by the Engineer-in-Charge.Note :- Necessary earth and PCC/Brick work will be measured and paid seperately |
| 30 | All as per Srl items No.28.00 here-in-before but of size 50 mm dia |
| 31 | All as per Srl items No.28.00 here-in-before but of size 40 mm dia |
| 32 | All as per Srl items No.28.00 here-in-before but of size 25 mm dia |
| 33 | Supply and fixing, connecting, testing and commissioning of gun metal globe valve or gate valve, as specified, having screwed ends on both sides, complete with iron hand wheel, union, long screw with check nut, suitable for use with iron pipes, including taking down and removing the existing gate/globe valve, dismantling of old connections, cleaning of pipe threads, supply of new valve, jointing with approved jointing material (white lead / PTFE tape), alignment, tightening, and making all joints leak-proof, testing the valve under working pressure for proper operation, and making good disturbed portions, complete all as specified and as directed by the Engineer-in-Charge. |
| 34 | All as per Srl items No.32.00 here-in-before but of size 50 mm dia |
| 35 | All as per Srl items No.32.00 here-in-before but of size 40 mm dia |
| 36 | All as per Srl items No.32.00 here-in-before but of size 25 mm dia |
| 37 | M&L for drilling and tapping Ductile iron/ Cast Iron water mains in position for branch connections of 15mm dia size complete all as directed at site. |
| 38 | M&L for drilling and tapping Ductile iron/ Cast Iron water mains in position for branch connections of 20mm dia size complete all as directed at site. |
| 39 | S&F in repair straight plain brass ferrules (or connecting screws)screwed both ends of 15 mm dia complete all as directed at site. |
| 40 | S&F in repair straight plain brass ferrules (or connecting screws)screwed both ends of 20 mm dia complete all as directed at site. |
| 41 | Supply and fixing in replacement of cast iron sluice valves, PN-16, with flanged or socket & spigot ends as specified, SS stem, gun metal working parts, flanges drilled to PN-16, jointing, testing and commissioning, complete all as specified and directed |
| 42 | All as per Srl items No.40.00 here-in-before but of size 350 mm dia |
| 43 | All as per Srl items No.40.00 here-in-before but of size 250 mm dia |
| 44 | All as per Srl items No.40.00 here-in-before but of size 200 mm dia |
| 45 | All as per Srl items No.40.00 here-in-before but of size 150 mm dia |
| 46 | All as per Srl items No.40.00 here-in-before but of size 100 mm dia |
| 47 | All as per Srl items No.40.00 here-in-before but of size 80 mm dia |
| 48 | Supply and fixing in replacement of cast iron non-return valve, PN-16, conforming to IS 5312 (Part-1) with flanged ends as specified, stainless steel hinge pin/shaft, gun metal working parts, flanges drilled to PN-16, including jointing, testing and commissioning, complete all as specified and directed by the Engineer-in-Charge. |
| 49 | All as per Srl items No.47.00 here-in-before but of size 350 mm dia |
| 50 | All as per Srl items No.47.00 here-in-before but of size 250 mm dia |
| 51 | All as per Srl items No.47.00 here-in-before but of size 200 mm dia |
| 52 | All as per Srl items No.47.00 here-in-before but of size 150 mm dia |
| 53 | All as per Srl items No.47.00 here-in-before but of size 100 mm dia |
| 54 | All as per Srl items No.47.00 here-in-before but of size 80 mm dia |
| 55 | Material and labour for construction of valve pit of sizes 140cmx140cmx140cm (internal dimentions), any type soil, returning, filling in, disposal of surplus spoil to a distance not exceeding 50m and depositing where directed, 100mm thick PCC in foundation of the mix (1:4:8), type D-2, (using 40mm graded crushed stone aggregate) brick masonry in cement mortar (1:4), rendering, 12 mm thick cement mortar (1:4) internally, finished even and fair & pointing flush externaly as the work proceeds in the same mortar, mild steel frame, MS sheet cover 5mm thick with handle and locking arrangement, painting all the exposed MS work with two coats of synthetic enamel paint of the tint as approved by the GE over a coat of red oxide primer and painting all the MS embedded in PCC with two coats of black bituminous paint including dismantling old unsv valve pit, complete all as specified. |
| 56 | Material and labour for construction of valve pit of sizes 100cmx100cmx100cm (internal dimentions), any type soil, returning, filling in, disposal of surplus spoil to a distance not exceeding 50m and depositing where directed, 100mm thick PCC in foundation of the mix (1:4:8), type D-2, (using 40mm graded crushed stone aggregate) brick masonry in cement mortar (1:4), rendering, 12 mm thick cement mortar (1:4) internally, finished even and fair & pointing flush externaly as the work proceeds in the same mortar, mild steel frame, MS sheet cover 5mm thick with handle and locking arrangement, painting all the exposed MS work with two coats of synthetic enamel paint of the tint as approved by the GE over a coat of red oxide primer and painting all the MS embedded in PCC with two coats of black bituminous paint including dismantling old unsv valve pit, complete all as specified. |
| 57 | Material and labour for construction of valve pit of sizes 60cmx60cmx60cm (internal dimentions), any type soil, returning, filling in, disposal of surplus spoil to a distance not exceeding 50m and depositing where directed, 100mm thick PCC in foundation of the mix (1:4:8), type D-2, (using 40mm graded crushed stone aggregate) brick masonry in cement mortar (1:4), rendering, 12 mm thick cement mortar (1:4) internally, finished even and fair & pointing flush externaly as the work proceeds in the same mortar, mild steel frame, MS sheet cover 5mm thick with handle and locking arrangement, painting all the exposed MS work with two coats of synthetic enamel paint of the tint as approved by the GE over a coat of red oxide primer and painting all the MS embedded in PCC with two coats of black bituminous paint including dismantling old unsv valve pit, complete all as specified. |
| 58 | Supply and fixing, jointing, testing and commissioning of Ductile Iron (DI) specials, suitable for socket and spigot (S&S) joints as well as flanged joints, conforming to IS:8329 / IS:9523 / ISO:2531, DI bends of any type, radius and angle, DI tapers of all types such as straight tapers, increasing or decreasing tapers, double socket tapers, tee pieces (single branch), Y-junctions, double branch tees, crosses, collars, end caps, and plugs, with all-socket, socket-and-spigot, or flanged end configurations, suitable for any bore size up to 350 mm diameter including lowering, aligning and jointing of specials using rubber gasket (push-on) joints for socket and spigot connections and bolted flanged joints for flanged connections, including supply and fixing of gaskets, nuts, bolts and washers, cutting and trimming where required, deflection at joints, provision of thrust / anchor blocks wherever necessary, and all jointing materials, labour, tools and accessories, pressure testing of joints, checking alignment and leak-proof performance, and commissioning of the pipeline, complete all as specified and as directed by the Engineer-in-Charge |
| 59 | Supply, laying, fixing, jointing, testing and commissioning of Electric Resistance Welded (ERW) steel pipes, including all steel specials, conforming to IS:3589 (1981) and subsequent revisions, having minimum wall thickness of 4.8 mm, suitable for water supply, laid in trenches or in open/exposed execution, as directed at site, including cutting, edge preparation, alignment, welding of joints (butt welded / fillet welded as applicable), and supply and fixing of all steel specials such as bends, elbows, tees, reducers, flanges, puddle pipes, collars, caps, etc.including lowering, positioning and supporting of pipes, provision of sand bedding where laid underground, necessary excavation and backfilling, making good disturbed surfaces,ncomplete with all materials, labour, tools, welding electrodes, consumables, plant and machinery, complete all as specified and as directed by the Engineer-in-Charge |
| 60 | All as per Srl items No.58.00 here-in-before but of size 80 mm dia |
| 61 | All as per Srl items No.58.00 here-in-before but of size 65 mm dia |
| 62 | M&L for mild steel as in cross arms bracing supports clamps and back planes fabricated from structural steel section including nut, bolts washers welding welding drilling holes for bolts in any shape and size as indicated or directed and inclusive of one primer coat one under coat one finishing coat of aluminium paint complete. paint complete to support the cables all as specified. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 14, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 28 daysDec 21, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 35 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender