Tender For Construction Of 15 Nos (9 Nos) Tube Wells In Jawali Area Tehsil Jawali Distt Kangra (H.P.)Sh :- Civil Work, Laying, Jointing And Testing Of Rising Main, Hdpe Pipe In Distribution System & Providing And Installation Of Submersible Pumping M
Tender Overview
Project Description
Tender for Construction Of 15 Nos (9 Nos) Tube Wells In Jawali Area Tehsil Jawali Distt Kangra (H.P.)Sh :- Civil Work, Laying, Jointing And Testing Of Rising Main, Hdpe Pipe In Distribution System & Providing And Installation Of Submersible Pumping Machinery Alongwith Allied Accessories Tubewell Kala Naal.
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in foundation and trenches ( For pipes and pits ) up to all depths in all classification of earth work such as pick work ,jumper work ,saturated soil including bailing or pumping out water ,blasting soft/hard rock or chiseling soft/hard rock where blasting is prohibited in all lifts including trimming & dressing of sides, leveling of beds to correct grade i/c shoring /strutting ,planking ,timbering & dewatering wherever required ,stacking the usable & unusable material /soil separately & after laying ,jointing & testing of pipes ,returning the useable soil in trenches in 15 cm ,layers including consolidating of such deposited layer by ramming & watering & then deposing of all surplus excavated soil / unusable material as directed with in all leads and lifts including restoration of unmetalled surfaces to its original condition and including cost of diversion for traffic , night signals ,fixing caution boards ,crossing over trenches for access to houses ,fencing etc. complete in all respects with in all lead and lifts as per direction & satisfaction of Engineer - in - charge. |
| 2 | Providing and laying cement concrete 1:3:6 ( 1 cement: 3approved sand : 6 approved graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth. |
| 3 | Providing and laying cement concrete 1:4:8 ( 1 cement: 4 approved sand : 8 approved graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth. |
| 4 | Providing and laying cement concrete 1:2:4 ( 1 cement : 2 approved sand :4 approved graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in: |
| 5 | Foundation , foootings base of columns and the like and mass concrete. |
| 6 | In foundation and plinth Including entire carriage of material within all leads and lifts. |
| 7 | Wall any thickness but not less than 0.10 mtr. Thickness attached pillasters, buttresses, plinth and string courses etc. from top of foundation level upto floor two level. |
| 8 | Providing and laying cement concrete work 1:5:10(1cement:5sand: 10 graded stone aggregate 40mm nominal size ) and curing complete excluding the cost of form in foundation and plinth with in all leads and lifts as per direction and satisfaction of the Engineer-in-charge. |
| 9 | Providing form work with steel plates 3.15mm thich welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring, shuttering struttting and propping etc.with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4mts. and removal of the same for in-situ reinforced concrete and plain concrete work in:- |
| 10 | Vertical , surfaces such as walls (any thichness) partitions and the like including attached pillasters, buttresses plinth and string courses. |
| 11 | Providing and laying cement concrete 1:1½:3 ( 1 cement:1½ approved sand :3 approved graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in: |
| 12 | Foundation , foootings base of columns and the like and mass concrete. |
| 13 | Wall any thickness but not less than 0.10 mtr. Thickness attached pillasters, buttresses, plinth and string courses etc. from top of foundation level upto floor two level. |
| 14 | Providing tor steel reinforcement for RCC work including bending, binding and placing in position complete upto floor two level with in all leads and lifts. |
| 15 | Excavation In drains & channels etc., in earth work,including dressing of side & bed and disposing of excavated earth upto a lead of 20 mtr.and lift upto 1.50 mtr.disposed earth to be levelled and neatly dressed. |
| 16 | Laying, jointing & testing in trenches to be levelled to grades, BIS marked GI pipes conforming to BIS:1239 ( latest with up to date amendments ) of 150 mm dia (Medium class PE) duly flanged after every 5th pipe with intermediate butt welded joints including the cost of flanges, bends of required degree, tee/ short pieces made from parent tubes of different degrees cutting , welding & jointing with flanges conforming to table as specified below of BIS:6392 ( latest with up date ammendments ) three layers (two layer out sides and one layer inner side) welded as per BIS:816 ( latest with up date ammendments ) with electrodes conforming to BIS 814 (latest with up date ammendments ) & provided with nuts & bolts BIS 1369 (latest with up date ammendments) of required sizes, 4 mm thick ( Champion make ) compressed asbestos fiber gasket or synthetic rubber gaskets conforming to BIS 2712 (latest with up date ammendments ) & approved specification as per site conditions including flushing, cleaning and hydraulic testing complete to respect with in all leads and lifts as per the direction and satisfaction of the Engineer-in-charge. (The earth work will be measured & paid separately) |
| 17 | 125mm dia flange table-17 |
| 18 | laying in trenches following dia and grade having suitable pressure 4.00 Kg.F / cm2 working pressure polythene pipes high density confirming to I.S. 4984-1972 complete with special flange compression type fittings. (Earth work in trenches to be measured and paid for separatly) within all leads and lifts. |
| 19 | 200mm dia HDPE pipe grade PE-80 PN-4 |
| 20 | 180mm dia HDPE pipe grade PE-80 PN-4 |
| 21 | 160mm dia HDPE pipe grade PE-80 PN-4 |
| 22 | Providing and fixing CI Alfa Valve of following dia complete in all respect. |
| 23 | 200mm dia |
| 24 | Supply of submersible pumping set of KSB/Kirloskar/Kilburn/Clama/Crompton/KSB/BS make conforming to BIS; 8034-1976 latest suitable for lifting clear water (latest with uptodate ammendments) fitted with bronze impellers/suitable alloy directly coupled to squirrell case electric induction motor of same make as (manufacurer standard) conforming to BIS; 9283-1979 (latest with uptodate ammendments) and totally water proof for submersible duty, isolated from the pump by intermediate casing with double mechanical seal in oil chamber, grease packed lubricated bearings & provided with stainless steel thrust bearing plate to with stand vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor including water level guard,errection clamps,cable clips & depth gauge etc. The pump shall be suitable for operation on data given below:- |
| 25 | Total Head :- 63.18 Mtr (Tube Well Kala Naal) |
| 26 | Discharge required from each pump. :- 9.01 LPS |
| 27 | No. of pump required :- 1.00 Nos |
| 28 | Location of the site of installation of machinery. :- The site is located at a distance of 5 Kmts from Jawali Railway Station |
| 29 | The Altitude of installation. :- 100.00 Mtr above MSL |
| 30 | Type of current. :- AC Three Phsae Supply witgh |
| 31 | Rate Voltage :- 415+ 10% |
| 32 | Type of water and its source :- Clear Water frome Tube Well |
| 33 | Charactristics of water. :- - |
| 34 | a)Ambient Temperature dig.c :- 20 dig. C |
| 35 | b)Turbidity NTU :- 113 NTU |
| 36 | c)Hardness260Mg/Ltrs(as CaCO3) :- 540 Mg/Ltr |
| 37 | d) PH 7.5 :- 6.50 to 8.50 |
| 38 | e)TDS :- 540 PPM |
| 39 | f)Other :- |
| 40 | Depth of T/Well :- 140.00 Mtr |
| 41 | LWL in T/Well :- |
| 42 | Center line level of Pump :- |
| 43 | Discharge level of highest point :- 418.80 Mr |
| 44 | Static head in Metres :- 58.32 Mtr |
| 45 | Length of R/Main (Including Column Assembly) :- 150 Mtr |
| 46 | Dia of Rising main :- 125.00 mm GI (M) PE |
| 47 | No of working hours per day :- 20.00 Hours |
| 48 | Limit of pump operation. :- (-) 15 % (+) 10% of total head |
| 49 | R.P.M. of pumping set. :- 2900 RPM ( or to be specified by the tenderer) |
| 50 | Test run :- 8 Hours continueously for 7 days |
| 51 | Providing and fixing automatic pannel borad of L&T make for 20HP machinery ( as per relavent IS/BIS standards) including auto start, auto stop and restart facility single phase preventer, 3 phase indicator timer, relay, selector switch, auto and manually start stop facilty, prevention of of phase reversal imbalance and overload and fixed with compatible starter in sheet enclosure with cabling complete in all respect to deliver results. |
| 52 | Providing and fixing of M-power module of ISI approved brand/make for automation of the pumping machinery including cost 01 No. mobile handset (02 No. Sim cards, 01 for module and 01 for moble phone) and recharge for one complete year and all accessories required for installation and comissioning of M-power module for complete in all respects within all leads and lifts as per direction and satisfaction of engineer in charge. |
| 53 | Providing M.S.Sheet 16-SWG steel fabricated floor mounted closed Almirah type sewitch board including angle iron post of suitable height and size ISA 65x65x6mm.duly painted comprising and capable of mounting the following accessories with all internal electric connections. Note:-The drawing of panel board shall be subject to approval of Engineer-in-Charge. |
| 54 | Ammeter for A.C.supply, 100mm.circular dial L&T Rishav/Auto Electric/AE/IMP/Havells make of suitable range for above Pumping Set with selector switches conforming to BIS-1248-1983(Latest edition). |
| 55 | Voltmeter for A.C.supply. 100mm.circular dial L&T Rishav/Auto electric/AE/Havells make of suitable for above Pumping set with selector switches conforming to BIS-8044-1978 (Latest edition). |
| 56 | ICT.Switchhes with HR fuses Kilburn/L&T/Standard/Siemens/Havell's make and having capacity 30% extra operational rating of Motor as per BIS-4064-1978 with uptodate ammendments immediately after the power of the Meter of the HPSEB. |
| 57 | Busbar chamber of approved make having 3 copper bars of suitable rating for full length equal to width of Board of 3-live phases and one copper bar of half rating of full length for neutral conforming to BIS-8084-1976 and 11353-1985 read with 5578-1985 all latest with uptodate ammendments. |
| 58 | MC3/MCCB/OCB of suitable capacity of Kilburn/L&T/MEI/Standard/GEC/Havell's make on incoming feeder for Pu ping set conforming to BIS-2516-1985 (Latest edition) with neutral linked under voltage release. |
| 59 | Three Phase indicating lamps complete with toggle Switches for individual motors conforming to BIS-3452Part-I&II latest with uptodate ammendments. |
| 60 | Hour Run Meter of reputed/approved make of four digit capacity conforming to BIS-722(Latest edition). |
| 61 | Supply of Kirloskar/Kilburn /IVC/Fouress/Gled/BHEL/ Leader make Cast Iron double flanged sluice valve of class PN 1.6 confirming to BIS-780-1984 (to be provided on delivery side) of equal size to one dia more than the dia delivery of pump and capable of with standing nominal seat test pressure of 16 kg/cm². (The size & class of valve shall be specified by the tender). |
| 62 | Providing and Supply of Kirloskar/ Kilburn/Leader make Cast iron double flanged swing check type reflux valve class PN 1.6 having bye pass arrangement ( to be provided on delivery side) of size of one size higher than the delivery size of pump and shall be suitable for withstanding nominal seat presure of 16.32 Kg/Cm2 as per BIS 5312-1984 Part-II. (The size & class of valve shall be specified by the tender). |
| 63 | Providing & laying PVC insulated jointless, flat water proof copper cable of Siemens/Finolex/ Grandlay/ Gloster make conforming to BIS:1554 (Part I) -1988 or latest with up to date ammendments of suitable size for the pump sets offered(one cable carrying all three phases) including all other electrical equipment /accessories such as thimbles ,flexible pipe, solder, nuts & bolts cable glands etc. laid in pipes or trenches under floor. The type,size & make will be subject to approval of HPSEB authorities.In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost. |
| 64 | On supply side of 3½ core coper cable 25.00 mm^2 ( From HPSEB Meter to Switch & Starter). |
| 65 | On motor side 3 core flat joint less copper cable of size 16.00 mm^2 ( From Switch & Starter to Motor) pump installed in the bore. |
| 66 | Supply of standarad make 100mm dia circular/square dial pressure gauge of suitable range Fiebeg/Bourden/ Precision make with all accessories such as stop cock,copper tubing etc. conforming to BIS 3624-1987 latest with up to date ammendments. |
| 67 | P/L G.I./MSERW pipe considering site requirements and having appropriate size in accordance with the delivery size of pumping set . The pipe shall conform to relevant BIS codes & capable of with standing the feild test pressure equal to 1.5 times the operating pressure including all type of fittings such as bends, tapers/ reducers, flanges, rubber gaskets 3mmthick, nuts & bolts and any other fitting required at site and work shall be to the entire satisfaction of Engineer-in-Charge. The pipe material shall conform to relevant BIS Code and capable of with standing FTP equal to 1.5 times the operating pressure the complete arrangement shall compromise of |
| 68 | Coloumn assembly (size to be specified by the tender) |
| 69 | Providing and lying double loop earthing with coper plate 600x600 x3 thick electrode and copper strip of 25x3 complete including providing of material such as charcoal, common salt, Gl pipes, thimbles, nuts & bolts, digging of pits, Copper /Gl wire/ Strips of required capacity conforming to BIS 8034-|978 latest with upto date amendments for above motor & other electriacl equipments including all civil works. |
| 70 | Errection of all equipments including cost of tees, bends tapers & any other fittings required as per site conditions & as per directions of Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Tender Published
Tender notice published.
CompletedBid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysBid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender