Water Resources and Irrigation Government Departments Closing in 3 days TDR #58516759

Tender For Providing Lift Irrigation Scheme To Village Telker,Bharial,Sanahi Kalan And Sanahi Khurd From Kunah Khad In Tehsil Nadaun Distt. Hamirpur(Sh):-Supplying And Errection Of Submersible Pumping Machinery In Booster Stage And Supply Errection O

Issued by Government Departments · Hamirpur, Himachal Pradesh
Tender Value
17.40 Lakhs
Estimated cost
Bid Submission
21 Nov 2026
3 days left
EMD
34800
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Hamirpur → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available

Project Description

Tender for Providing Lift Irrigation Scheme To Village Telker,Bharial,Sanahi Kalan And Sanahi Khurd From Kunah Khad In Tehsil Nadaun Distt. Hamirpur(Sh):-Supplying And Errection Of Submersible Pumping Machinery In Booster Stage And Supply Errection Of Centrifugal Pumping Machinery With Allied Accesories Pump House To Mdt.

BOQ

Name of Work:- Providing lift irrigation scheme to Village Telker,Bharial,Sanahi Kalan and Sanahi Khurd from Kunah khad in Tehsil Nadaun Distt. Hamirpur(SH):-Supplying and errection of Submersible pumping machinery in Booster stage and Supply errection of Centrifugal Pumping Machinery with allied accesories Pump house to MDT.
Sl. No. Item Description
1Submersible pumpset ( Booster stage)
2Supply & Errection of horizontal spindle, vertical split casing single/multistages Subminible pumps of Standerd make such as KSB/Kirloskas/WPIL Confirming BIS 8034-1976 (Latest with upto date ammendments) to handle raw water with implellers Casing , ring & shaft sleeves of bronze shaft of steel with Cast iron Casing of suitable Capacity coupled directly through a flexible Coupling on a common base to Kirloskar/NGEF/ crompton/Siemen/ABB/Squirrel Cage screen protected drip proof induction electric motor Suitable for operation on the data given below:-
3SITE CONDITIONS:-
4Location of site:- Kunah Khad
5The altitude of place in which the motor is intended to work in ordinary service.- 450 mtrs.
6Humidity:- Humid during rainy season
7Nature of atmosphere:- Normal
8Detail of quality of water:- Raw water
9Water free from sand or not:- Free from sand
10Water corrosive or not:- Not corrosive
11Turbidity:- upto 500 ppm
12Type of well:- Jack well
13Inside dia of well:- meter dia.
14Depth of water during HFL in the well:-
15Maximum draw down:- mtrs.
16Depth of well :- 10.00 mtrs.
17Any other information if required.
18OPERATING CONDITIONS
19Type of current:- AC. Three phase
20Operating frequency 50 Hz.
21Rated voltage 400(+/-) 10% volts.
22System of earthing if any to be adopted Double loop earthing as per BIS: 3243-1987 latest with upto date amendments .
23Speed of revolutionTo be quoted by tenderer
24Direction of rotation To be quoted by tenderer .
25No. of working hours per day. 20 hours
26The maximum temperature of cooling air and water in the place in which the pump set is intended to work in ordinary service Temperature of place to be specified 20oC to 42oC.
27MOTOR
28Ref. to BIS code BIS 9283-1979 with upto date amendments
29Type of enclosure of motor. As per BIS-4691-1985 (Latest)
30Type of duty : Continuous
31Mechanical output in KW Suitable for driving submersible pumps required for duties specified against pumps. To avoid over loading of motor a margin of about 15-20% may be kept in the rated output to prime Mover.
32Class of insulation Class –B
33Max. Permissible temp. Rise of motor reqd. if different from that given in 8 (viii) above.To be specified by the tenderer.
34Particulars of test reqd. & where they are to be conducted. AS per terms and conditions attached.
35Particulars as to whether voltage limiting device will be employed. Oil immersed star delta starter to be installed between bus bar and motor. Shunt capacitor is also proposed to be installed for improving the power factor at site.Note:- Star delta starter upto 37.5 Kw.
36Type of motor Star Delta strater up to 37.5 KW As per BIS 9283-1979 or latest.
37Details of shaft extension required
38Break way torque in terms of rated load torque and the corresponding break-way starting current which may be taken from the supply with the starting apparatus in circuit should not exceed 2.5 times of the full load current .
39Nature of load and any information regarding the driven machine which has a bearing upon the torque reqd. during the accelerated period, the kinetic energy of the moving parts to be accelerated and No. of starts during a specified period.
40Where possible fault capacity of the system to which the motor is connected.The motor should be able to withstand initial current of 2.5 times the rated current for two minutes without suffering damages or permanent deformations.
41PUMPS
42Nos. of pumps required. 2 No. pumps (Both will run simultaneously)
43Spare parts required. For two years normal maintenance as recommended by manufacturer.
44Type of drive. Electric induction motor.
45Optional fittings required
46Pump Operating conditions
47Capacity 18.78 LPS for each Pump
48Total head in meters 19.95 meter
49Static head 17.00 meters
50Minimum depth of water Meters
51Variation in water level meter
52Ground level to Max. water level meter
53Ground level to delivery point Meter
54Pressure in the suction tank.
55Pressure in the delivery tank
56Length of rising main 90 meters
57Dia of rising main 200 mm dia
58Turbidity of water upto 500 PPM
59Drive type Electric driven
60Limits of total head in which the pump is required to operate. (-) 15% to (+) 10% of total head
61Suction/Delivery size of pump
62Efficiency of pump at
63a) Duty head
64b) (+) 10% head.
65c) (-) 15 % head.
66Material of construction. To be specified by the tenderer (manufacturers certificate to be appended)
67Supply of Direct on line of MEI/Kilburn make conforming to BIS 8544-1979 latest with upto date amendments for squirrel cage induction motor (make to be specified by the tenderers) mounted on panel board with magnetic type over load release and gas-pots, time legs, under voltage release & initial oil filing of suitable capacity.
68Supply of MS. Angle iron steel sheet 16 SWG fabricated floor mounting closed (Almirah type) switch board comprising and capable of mounting the following accessories and with all internal electric connections, duly painted. The drawing of panel board shall be subject to approval of Engineer-in-Charge.
69Ammeter AC supply, 100 mm square type auto electric of AE/ L&T Rishab make of suitable capacity for above motor with selector switches conforming to BIS-1248-1983 latest with upto date amendments.
70Voltmeter AC supply, 100 mm square type auto electric AE/ L&T Rishab make of 0-500 Volts range for above motor with selector switches conforming to BIS-1248-1983 latest with upto date amendments.
71ICTP switches with HRC fuses of Havells/L&T/standard /cromption make for required motor of suitable capacity and conforming to BIS: 4064-1978 latest with upto date amendments.
72Bus bar chamber having 3 copper bars of suitable rating for full length of 3 phases and one bar of half the rating of full length for neutral conforming to BIS: 8084 –1976 and 11353-1985 read with 5578-1985 all latest with upto date amendmentsof suitable rating.
73MCB of suitable capacity of Havells/standard/MDS/Jyoti/Kilburn make to feed motors offered by the tenderer conforming to BIS: 2516-1985 latest with upto date amendments with neutral linked under voltage release.
743 phase indicator lamps complete with toggle switches for individual motors conforming ti BIS 3452 part I & II latest with up to date amendments of 15 watts.
7550 mm dial Hour run meter of CEE/NEE make of suitable range as per relevant BIS specifications.
76Supply of Kirloskar/leader make dia. cast iron class PN. 1.0 double flanged sluice valve having size one dia. Higher than pump size to delivery of pump and capable of with standing nominal seat pressure of 10.20 kg/cm2 as per IS :780-1984 (Part I)
77Supply of Kirloskar/leader make dia. cast iron (class PN. 1.0) double flanged ( swing check type) reflux valve having bye pass arrangement and having one dia. Higher than pump size to delivery of pump and capable of withstanding nominal seat pressure of 10.2 kg/cm2 as per BIS-5312-1984.(Part-I).
78Supply of Leader /Kirloskar make 200 mm dia. cast iron class PN. 1.0double flanged (swing check type) reflux valve having bye pass arrangement and size equal to dia of rising i.e. 250 mm for withstanding nominal seat pressure of 10.2 Kg/Cm 2 as per BIS 5312-1984 (Part-I )
79Supply of PVC joint less flat water proof cable as per BIS: 694-1990 latest with upto date amendments suitable for the pump sets offered from MCB to motor including all other electrical equipment/accessories such as thimbles, flexible pipes solder, nuts and bolts, cable glands etc laid in pipes of trenches under floor. The type, size and make will be subject to approval of HPSEB authorities & in case of non acceptance by HPSEB authorities it shall have to be replaced by tender.
80Providing and laying double loop earthing with G.I. wire & G.I plate complete with material such as charcoal, common salt, GI. Pipes, thimbles, nuts and bolts, digging of pits, GI. Wiring and aluminum strips of required capacity conforming to BIS: 3043-1987 latest with upto date amendments for above motors and other electrical equipment’s.
81Supply of standard make circular dial pressure gauge 0-16 kg/cm2 range of feibig make with all accessories such s stop cock, copper tubing etc, conforming to BIS: 3624-1987 latest with upto date amendments.
82Providing and laying delivery pipe . and common header 200 mm dia GMSERW jointed with MS flanges of table-17 as per IS: 6392-1971 (upto a length of 20 mtrs ) including rappers, flanges, rubber gaskets, nuts and bolts and specials upto 5 mtrs away from the outer wall of pump houses as per layout drawings approved by Engineer-in-Charge.
83Supply of floor/wall mounted power factor shunt capacitor conforming to BIS: 2834-1986 latest with upto date amendments Baja/L&T/Asian/cromption make to raise the prevailing power factor at site to 0.95 for direct connection to induction motor individually of suitable rating each including cable of siemens/Gloster/ICC make form bus bar chamber to capacitor and also including L&T/LK/Kilburn make ICTP switches conforming to BIS –4064-1978 or latest with HRC fuses (range to be specified by the tendrerer).
84Supply of suitable cable for water level guard
85Supply of supporting clamps.
86Supply of cable clips of required size.
87Erection of all equipment from Sen. 1 to 4,6,7,9 ,11 & 14 including cost of tees, bends, tapers and any other fittings required as per site conditions and as per direction of Engineer-in-charge.
88Centrifugal pumping set (1st stage)
89Supply ,Installation ,Testing & Commissioning of energy efficient horizontal spindle, horizontal/ radial split casing/end suctions (back pull out arrangement)single/double/multistage centrifugal pump suitable for operation, in parallel of recommended make such as Mather and platt/KSB/Kirloskar/Jyoti /Beaconweir confirming to BIS-1520-1980 with upto date ammendments, read with IS:9137-1978 or latest edition suitable for lifting over Raw water for under mentioned characteristics with bronze/Bronze with 2.5% Nickel impellers, dia of 405mm priming funnels, casing ring and shaft sleeves of bronze/ steel, shaft of SS:410/AIS 1431 Chrom in plated with cast iron casing coupled directly through a flexible coupling on a Common MS base plate to squirrel cage induction motor TEFC type energy efficient minimum IE2 compliance conforming to IS:- 12615-2018 of standard make such as Kirloskar/BHEL/ Crompton/NGEF/GEC/Siemens/ Jyoti/ ABB/Marathon and suitable for operation on LT, 50 cycles/second 3 phase AC electric supply. The pump set should include water level guards, erection clamps , cables , depth gauge, double loop earthing, NRV, common header,Sluice valves and actuated valves of approved class including errection charges etc. The power of electric motor/motors should be at least (+) 10% in excess of the maximum power required by the pump/pumps in the operation range of (+) 10% and (-) 15% of the duty point head. The motor/motors should be as per IS: 325-1978 with upto date amendments read with IS:900-1972. The starting current of the motor shall be limited to not more than 4.5 to 5 times of full load current pumping set complete I/C allied acessories.
90read with IS: 900-1972. It should include cost of bearing nuts, bolts and pointing etc. and should meet the following requirements:-
91Discahrge (Q) : -Total 18.782 LPS
92Total dynamic head : 143.04 Mtr.
93(a) LWL in sump well (h) :529.00 Mtrs.
94(b) Shaft level : 527 Mrs
95(c ) Level at discahrge point :640 Mtrs.
96(d) Suction lift :0.00 Mrtrs
97(e) Residual head :3.00 Mtrs.
98(f) Static head : 104 Mtrs.
99(i) Rising Main :
100(a) Length 2760 Mtrs.
101(b) Dia. :200 mm
102(iv) Pumping Hours : 20 Hours
103(v) Altitude of installation above MSL : 500
104(vi) Characteristics of water :
105(a) Temperature : 20.00 0 C
106(b) Ambient temperature 42 Oc
107(c ) Turbidity upto 500 NTU
108(d) Alkalinity MG/CA CO3
109(e) Size of the solids mm
110(f) Other
111Providing ICTP Main Switch with HRC fuses/Side handled operated Change over switch of L&T/Crompton/Standard/Havells make suitable capacity Operational rating as per IS: 4064-1978 with up to date amendments immediately after the power meter of HPSEB
112Providing M.S. sheet, steel fabricated floor mounted closed ( Almirah type) switch board including angle iron post of suitable height and size ISA 40x40x6mm, duly painted, with steel sheet of 16 gauge comprising, capable of mounting the following accessories with all internal connections:-
113M.C.B. Havell/MDS/Standard of make of suitable capacity on incoming feeder with or without initial oil filling as the case may be with neutral linked under voltage releases as per IS: 2516-1985 with up to date amendments with.
114E.L.C.B. of Havell/MDS/INDETEC make as per IS: 2516-1977 with upto date amendment which should have control box operating handle and trip/reset bush button on/off indicators, re-indicating off spring condition of the circuit breaker for over current protection. The circuit should be equipped with magnet thermal release with metallic tape etc. It should also be lifted with earth fault for tripping of breaker on occurrence of earth fault on off breaker load side end.
115The voltage monitor relay of L&T/AE make three phase with all protection and usual indicator and electric siren against single phasing low voltage, high voltage, reverse phasing, over loading and phase voltage difference as per IS: 3842 ( Latest edition).
116100mm square type A.C. supply voltmeter of AE/L&T Rishab make of suitable range with selector switches as per IS: 4064-1978 with up to date amendments.
117Power factor meter of AE/L&T Rishab make as per relevant IS codes with up to date amendments of suitable rating.
118Frequency meter of AE/ L&T Rishab make as per relevant IS: Codes with up to date amendments of suitable rating.
119Bus bar chamber with copper strips having three bars of suitable rating for full length equal to the width of the board for three live phases and suitable for induced current, one copper bar of half the rating of full length for neutral phase as per IS: 8084-1976 and IS: 11353-1985 read with BIS 5578-1985 with up to date amendments 63 Amp.
120ICTP switches with HRC fuses of L&T/ Standard/Havells make and of suitable capacity as per IS: 4064-1978 with up to date amendments.
121Three phase indicator lamps complete with toggle switches for individual motors as per IS: 3452 ( P-I&II) with up to date amendments.
122100mm Square type AC supply Ammeter of AE /L&T Rishab make of suitable range with selector switches and CTS operated as per IS:1248 (P-II) 1983 with up to date amendments.
123Capacitor of L&T/Bajaj/Assian/Crompton make as per IS:2834-1986 with up to date amendments to raise the power factor at site to 0.95 for direct connections to induction motor individually of required KVAR rating according to HP offered including cables as per relevant ISI code ( of Siemens/Glocter/IEC make) from bus bar chamber to capacitor and also including ICTP switches of appropriate range as per IS: 4064-1978 with upto date amendments
124Providing suitable Star delta starter of MEI/Kilburn make as per IS: 8544-1979 with up to date amendments for Squirrel Cage motor mounted on panel board with magnetic type overload release and dashpot time lag, under voltage release with or without initial oil filling as the case may be with single phase preventor as per IS 1248 (P-V)-1983 with up to date amendments.
125Providing Hour run meter of recommended make of suitable capacity as per IS: 722 (Latest edition)
126Providing double flanged Cast iron sluice valve of Leader/Kirloskar make of 200 mm dia for the suction pipe and capable of withstanding the normal seat pressure 16.32kg/cm as per IS: 780-1984 class PN 1.6 with upto date ammendments.
127Providing double flanged Cast iron sluice valve of Leader/Kirloskar make and size one dia. higher than pump for the delivery line of the pump and capable of with standing the normal seat pressure 16.32kg/cm as per IS: 780-1984 class PN 1.6 with upto date ammendments.
128Providing double flanged (Swing type) CastSteel reflux valve of Leader/Kirloskar make and one dia. higher than pump having bye pass arrangement on the delivery line of pump and capable of with standing normal seat pressure 16.32 Kg/cm2 as per IS: 5312-1984 class PN. 1.6 with uptop date ammendments.
129Providing double flanged Cast steel non return valve of Leader/ Kirloskar make and of 200 mm dia. having bye pass arrangement for rising main and capable of with standing normal seat pressure 16.32 Kg/cm2 as per IS: 5312-1984 class PN. 1.6 with uptop date ammendments.
130Providing 100mm dia. circular dial pressure gauge of Fiebig make complete with all accessories such as stop cock, copper tubing etc. as per IS: 3624-1987 with up to date amendments range 0-52 Kg/cm2
131Installation of all the items appearing at Serial No. 1 to 8 as per the systematic drawing attached with the tender documents.
132Providing and fixing double flanged GMSRW . piping work layout to be approved by the Engineer-in-Charge for suction and delivery pipes suitable to pump(s) offered and common header as per the rising main respectively complete with all specials such as bends ,tees reducers/ increasers with companion flanges matching with the relevant specifications of the accessories as indicated in the drawing No.2 including rubber/asbestos gasket of minimum 3mm thickness as per IS 2712-1979 and required number of nuts and volts as per IS: 1364-1983. The pipes shall be as per relevant IS Code and to withstand 1.5 times total head stipulated under item No.1.
133The size of the various components to be as under:- (i) Suction pipe As per site Requirement (ii) Delivery pipe As per site Requirement (iii) Common Header As per site Requirement And will extend up to 5 meters from the outer wall of the pump house in the direction to be jointed.
134Providing and laying copper PVC insulated armoured power cable ( one cable carrying all the three phases) of suitable size and capacity to and all other electrical equipments as per IS: 1554 (P-I)1988 or latest with upto date amendments of Siemens/ IEC/ICC/GICO/Grandly/National make including all other accessories such as thimbles, flexible, pipes solder, nuts and bolts, cable glands etc. laid in pipes or trenches under floor. Motor side: Suitable size cable Min length = 20 mtrs. Supply side: Suitable size cable Min. length =10 mtrs.
135Providing and fixing double loop earthing and G.I. plate 600mmx600mmx3mm thick electrode complete with material such as thimbles, nuts and bolts, charcoal and common salt, 25mmx6mm G.I. strips & G.I. wire as per IS: 3043-1987 with up to date amendments for motors and other electrical equipments and digging of pits etc. complete in all respect. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58516759
AUTHORITY Government Departments
TENDER VALUE 17.40 Lakhs
LAST DATE 21-11-2026
Authority
Authority Name Irrigation And Public Health Department
Work Description Tender for Providing Lift Irrigation Scheme To Village Telker,Bharial,Sanahi Kalan And Sanahi Khurd From Kunah Khad In Tehsil Nadaun Distt. Hamirpur(Sh):-Supplying And Errection Of Submersible Pumping Machinery In Booster Stage And Supply Errection Of Centrifugal Pumping Machinery With Allied Accesories Pump House To Mdt.
Basic Detail
Tender No JS-NDN-CB-Misc.Agr/2026-27/-
Bidding Type Tender
Location
City Hamirpur
State Himachal Pradesh
Key Dates
Publish Date 13 Nov 2026
Submission Date 21 Nov 2026
Open Date 21 Nov 2026
Finance
Tender Value 17.40 Lakhs
Tender Fee 500
EMD 34800
Exemption Not Available
Document List
b2a3c0c5-f168-4616-bef7-a6be4d554171.html
BOQ_221077.xls
Form12.pdf
form6.pdf
Tendernotice_1.pdf
Termsandcond.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 13, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Nov 21, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 3 days
Nov 21, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 3 days

Tender Documents

Download All (ZIP) ↓
html

b2a3c0c5-f168-4616-bef7-a6be4d554171.html

xls

BOQ_221077.xls

pdf

Form12.pdf

pdf

form6.pdf

pdf

Tendernotice_1.pdf

pdf

Termsandcond.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender