Tender For Repair To Hardstanding, Footpath, Drain, Fencing, Boundary Walls, Culverts And Other Misc Items Of Zone- B Under Age Br-I At Mil Stn Bikaner.
Tender Value
35 Lakhs
Estimated cost
Bid Submission
02 Dec 2026
10 days left
EMD
70000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bikaner → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair To Hardstanding, Footpath, Drain, Fencing, Boundary Walls, Culverts And Other Misc Items Of Zone- B Under Age Br-I At Mil Stn Bikaner.
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling posts or struts (wood, steel or RCC), any section, including taking out embedded portion and making good disturbed ground, posts embedded in concrete, brick work, masonry, etc complete all as specified and directed . |
| 2 | Dismantling fencing wire mesh, any type complete all as specified and directed . |
| 3 | Dismantling structural steel work including door ,gates etc complete all as specified and directed . |
| 4 | Demolition of cement concrete (unreinforced) of any description and in position not otherwise specially provided complete all as specified and directed. |
| 5 | Taking down cement or cement lime plaster, any description, on brick or stone walls etc. including raking out jopints, hacking for keys, scrubbing down with water etc complete all as specified and directed . |
| 6 | Excavation in post holes (or similar holes) in loose/ soft soil each not exceeding 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exeeding 25cm, watering and removing surplus soil to a distance not exceeding 50m and making good surface complete all as specified and directed . |
| 7 | M&L for brick work with fly ash bricks (old size) straight or curved on plan exc 6m mean radius built in CM 1:6 including demolition of old brick work complete all as specified and directed . |
| 8 | M&L for pre cast RCC jali 35mm thick in PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate set and jointed in CM 1:4 incl dismantling of old jali complete all as specified and directed . |
| 9 | M&L providing reinforced cement concrete type B1 , 1:2:4 (20mm graded aggregate) in precast post for securing RCC jali post straining or terminal post struts etc for fencing average sectional area not exc 100 sqcm height up to 100cm , with or without chamfered angles and flat splyed, rounded or mitred tops including taking down old posts complete all as specified and directed . |
| 10 | M&L Granite (of any type) 18mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including cutting and polishing types as in platform or as in vertical surface over 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4 and finished even and fair including moulding ,rounding to egdes etc. and dismantling if required Complete all as specified and directed |
| 11 | M&L for 15mm thick rendering in cement mortar 1: 4 on other than fair faces of brick work or concrete surfaces, finished even & smooth without using extra cement complete all as specified and directed . |
| 12 | Supply only Integral water proofing compound, ISI marked, complete all as specified and as directed. |
| 13 | M&L for Mild steel work conforming to Fe-290 Gde E-165 in nosing to steps including embeding in concrete and screwing etc, wind ties for roof including securing bolts, posts & struts in fencing including cutting top to shape as directed, drilling holes, notching for wire, etc, flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc complete all as specified and directed. |
| 14 | M & L for PCC (1:3:6) type C2 using 40mm graded stone aggregate in foundation/filling and mass concrete complete all as specified and directed. |
| 15 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rail, straining bolts, etc including provision of binding wire complete. |
| 16 | Supply only chain link mild steel galvanized fencing, any type or size complete all as specified and directed.Note- The weight of chain link fencing shall be ascertained by BOO as odered by GE and Payment shall be made accordingly. |
| 17 | M&L Mild steel round bars 10 mm dia or over, cut to length, bend to shape required, fixed independently to support chain link fencing conforming to Fe 410-W Gde E-250 complete all as specified and directed. |
| 18 | M&L for Mild steel screw bolts (machine made) with hexagonal or square head at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut,length of bolt exc 5 cm but not exc 10 cm long and dia of shank 11 to 15mm complete all as specified and directed. |
| 19 | M&L Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, ladders etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing of Gde Fe410-0 or Fe 310-O complete all as specified and directed. |
| 20 | Supply and Fixing mild steel work as in flats , ties, straps etc. complete all as specified and directed. |
| 21 | S&F Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm to 80mm spacing and straining and ixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins etc including dismantling of existing barbed wire in any position complete all as specified and directed. |
| 22 | M&L welding in repairs not exc 2.5 cm in length and thickness of metal to be welded exc. 6 mm but not exc. 9 mm complete all as specified and directed. |
| 23 | S&F 1.5 mm thick plain colour PVC sheet fixed or laid on to flush doors, steel gates, as in roof etc. as in cladding by using rubber based adhesive, drilling and screw complete all as specified and directed. |
| 24 | M&L for providing ( factory made) precast cement concrete type B-1 (1:2:4) (using 20 mm graded crushed stone aggregate) as in apex stones, Kerb stone etc. (of any section indicated), with plain fair faces, including rounding , chamfers, weatherings, throat- ing etc. and setting in mortar 1:4 complete all as specified and directed. ( Note : Size of factory made Kerb Stone as decided at site by Eng-in-Charge and unit rate includes cost of excavation if any involved at site) |
| 25 | M&L for cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete including sub base of floors or in paving i.e. interlocking pavour block, chequered tiles etc. complete all as specified and directed. |
| 26 | M&L for 75mm thick cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) any thickness, as in flooring/hardstanding laid in alternate panels incl all necessary formwork and vibrator to be used complete all as specified & directed . |
| 27 | M&L for cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in coping, plinth course, parapets or roof kerbs, rounded or chamfered on edges and kerb stone, as in floor including necessary form work complete all as specified and directed. |
| 28 | M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour,design & pattern as in footparth, parks,lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand all as specified and directed. |
| 29 | M&L for providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour,design & pattern as in footparth, parks,lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 30 | M&L Chequerred cement concrete tiles 30 cm x 30 cm x 25mm thick mixed with pigment top thick with grey cement and pigmet machine pressed, set, jointed and pointed in neat cement slurry in floors over and including 15 mm thick screed bed in cement and sand mortar 1:6 complete all as specified and directed. |
| 31 | M&L for plastic dividing strips , 1.5 mm thick and 38 mm width and inserted in position to confirm to design complete all as specified and directed. |
| 32 | M&L Forming 12mm thick expansion joint filled with pre-formed bituminous filler and top 30mm primed and sealing compound grade 'A' in concrete slab upto 100 mm thick ,complete all as specified & directed. |
| 33 | M&L for old painted surface steel and iron surface of any description over 10cm in width or girth and applying a coat of synthetic enamel paint over & including a coat of red oxide zinc chrome primer complete all as specified and directed. |
| 34 | M&L for preparing new or previously untreated steel and iron surface of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over & including a coat of red oxide zinc chrome primer complete all as specified and directed. |
| 35 | M&L for preparing new plastered or unplastered surfaces of walls and applying two coats of cement paint white or tinted over a coat of primer as per manufacturer's instructions complete all as specified and directed. |
| 36 | M&L for preparing Old plastered or unplastered surfaces of walls and applying two coats of cement paint white or tinted over a coat of primer as per manufacturer's instructions complete all as specified and directed. |
| 37 | M&L for preparation to old concrete painted surface of any description over 10cm girth or width, not otherwise described and apply two coats of synthetic enamel paint complete all as specified and directed. |
| 38 | M&L for preparation to New concrete painted surface of any description over 10cm girth or width, not otherwise described and apply two coats of synthetic enamel paint complete all as specified and directed. |
| 39 | M&L Broken bricks hardcore of gauge not exc 63mm deposited, spread and levelled in layers not exc 15mm thick, watered and rammed to a true surface complete all as specified and directed. |
| 40 | M & L extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement incl forms, mould, mitred, stopped ends etc complete all as specified and directed. |
| 41 | M & L RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in precast cement concrete, drain covers (vibromechenically floated ) including all use of forms, moulds or machine moulds and setting the blocks, slabs etc in cement mortar 1:4, including demolition of old covers complete all as specified and directed. (Reinforcement shall be measured and paid separately under respective item of schedule \\"A\\") (Note : Curing arrangements shall have to be made by contractor at its own with out any claim on cost incurred) |
| 42 | M&L for TMT bars 5 mm dia and over upto and including 10mm dia in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 13, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 02, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysDec 09, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender