Tender For Addition/Alteration Special Repair To Bldg. No P-2031 Under Ge (North) Bathinda At Bathinda Mil Stn
Tender Value
46.60 Lakhs
Estimated cost
Bid Submission
26 Nov 2026
4 days left
EMD
93200
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bathinda → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition/Alteration Special Repair To Bldg. No P-2031 Under Ge (North) Bathinda At Bathinda Mil Stn
BOQ
| Sl. No. | Item Description |
| 1 | Material and labour for providing, fabricating and fixing mild steel framed work for doors, gates and similar assemblies, using MS angles or other approved steel sections conforming to grade Fe 410-0 or Fe 310-0, including cutting, drilling, welding and fabrication with necessary gusset plates, rails, braces, stiffeners and other structural members, making suitable holes for fixing steel sheeting or other approved covering, preparing the frames for hanging or sliding, providing and fixing hooks and hinges or suitable steel hanging door fittings, including hanging, alignment, fastening and securing the frames in position, complete with all necessary welding, bolts, nuts and accessories, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 2 | Material and labour for providing and fixing 1 mm thick mild steel plain black sheet for wall cladding, steel gates and similar works, including cutting the sheets to the required sizes and shapes, punching necessary holes, bending, folding and turning up edges, forming mitred angles and other profiles as required, fixing to existing or newly provided timber/MS framing with round-headed screws, clout nails or rivets, providing 40 mm wide plain lap joints, and securing the joints by riveting or welding as required, including all necessary drilling, welding, cutting, fitting, alignment and finishing, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 3 | Supply and fixing, in repairs, of 2 mm thick fibre-reinforced transparent plain sheeting (glass-reinforced fibre sheet), in individual panes not exceeding 0.50 sqm each, in windows, ventilators and similar openings, including carefully removing the existing damaged glazing/sheeting, cutting and trimming the new sheet to the required size, fixing in position with oil putty, screws and suitable washers, providing necessary overlaps and secure fastening, ensuring proper alignment, watertightness and neat finishing, and making good the adjoining surfaces, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 4 | Material and labour for providing and fixing, in repairs, 4 mm thick ordinary-quality sheet glass in individual panes not exceeding 0.50 sqm each, including carefully removing the existing broken/damaged glass and old putty, cleaning and preparing the rebates, cutting and fitting new glass to the required size, glazing and securing in position with approved oil putty, ensuring proper seating, alignment and uniform putty fillets, removing excess putty, cleaning the glass and making good the adjoining surfaces, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 5 | Material and labour for providing and fixing, in repairs, 4 mm thick figured glass, pinhead type, in individual panes not exceeding 0.50 sqm each, including carefully removing the existing broken/damaged glass and old putty, cleaning and preparing the glazing rebates, cutting and fitting the new figured glass to the required size, glazing and securing in position with approved oil putty, ensuring proper seating, alignment and uniform putty fillets, removing excess putty, cleaning the glass and making good the adjoining surfaces, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 6 | Supply and fixing, in repairs, of mild steel wire cloth having nominal wire diameter of 0.56 mm and average aperture width of 1.18 mm, in existing steel or wooden frames, including cutting and trimming the wire cloth to the required size, fixing tightly and uniformly in position with stainless steel wire staples, ensuring proper tension without sagging or wrinkles, securing all edges firmly and making good the fixing, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 7 | Material and labour for carrying out welding work in repairs, for weld joints not exceeding 2.5 cm in length, on metal sections/plates of any thickness, including cleaning and preparing the surfaces to be welded, removal of rust, paint and other impurities, cutting or dressing of edges wherever required, providing suitable electrodes and welding consumables, carrying out electric arc welding to form a sound and continuous weld, chipping off slag, grinding and finishing the welded portion flush wherever required, and applying protective primer to the affected area, if specified, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 8 | Material and labour for carrying out welding work in repairs to mild steel/steel sections, plates and other metal components not exceeding 6 mm in thickness, including cleaning and preparing the surfaces to be welded, removal of rust, paint and other impurities, cutting and dressing of edges wherever required, providing suitable welding electrodes and consumables, carrying out electric arc welding to achieve sound and continuous weld joints, chipping off slag, grinding and finishing the welded portions wherever required, and applying protective primer to the affected areas, if specified, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 9 | Material and labour for preparing new steel and iron surfaces of any description, not otherwise specified, exceeding 10 cm in width or girth, including removal of rust, mill scale, dust, grease and other foreign matter by wire brushing, scraping and cleaning, applying one coat of approved red oxide metal primer uniformly over the prepared surface, followed by two coats of approved synthetic enamel paint of required shade and finish, allowing adequate drying time between successive coats, including all necessary surface preparation, application, tools and tackles, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 10 | Material and labour for preparing old painted steel and iron surfaces of any description, not otherwise specified, exceeding 10 cm in width or girth, including cleaning the surface to remove dust, dirt, grease and other loose particles by rubbing with sandpaper, wiping with clean cloth and brushing with a dry paint brush, ensuring that the existing paint surface is sound and suitable for repainting, and applying one coat of first-quality approved synthetic enamel paint of required tint/colour by brush to obtain a uniform, smooth and glossy finish, including all necessary materials, labour, tools and tackles, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 11 | Taking down carefully existing cement or cement-lime plaster from brick walls and similar surfaces, including hacking and removing the plaster without damaging the underlying brickwork, raking out mortar joints to the required depth, hacking the surface to provide adequate key for subsequent replastering, scraping off all loose mortar and plaster particles, scrubbing and washing the surface thoroughly with water, and removing the dismantled plaster debris to the location as directed by the Engineer-in-Charge, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 12 | Material and labour for providing and applying 5 mm thick cement mortar rendering/plastering in CM 1:3 to ceiling surfaces in patches, matching the existing plaster thickness, including preparation of the existing surface by removing loose particles, dust and deteriorated plaster, hacking and providing adequate key, thoroughly wetting the surface, applying cement mortar uniformly to the required thickness, finishing fair, even and smooth without using extra cement, matching the adjoining existing plaster in texture and level, curing and cleaning the affected area, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 13 | Material and labour for providing and applying 15 mm thick cement mortar rendering/plastering in CM 1:6, matching the existing plaster thickness, on old brickwork or concrete surfaces of walls, pillars, cornices and similar surfaces, in patches, including preparation of the existing surface by removing loose and deteriorated plaster, dust and foreign particles, raking out joints in brickwork and hacking concrete surfaces to provide adequate key, thoroughly wetting the surface, applying cement mortar uniformly to the required thickness, finishing the surface even and smooth without using extra cement, matching the adjoining existing plaster in line, level, texture and finish, curing and cleaning the affected area, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 14 | Material and labour for providing and applying 15 mm thick cement mortar rendering/plastering in CM 1:4 on external faces of brick walls and concrete surfaces, including preparation of the surface by raking out masonry joints, hacking concrete surfaces to provide adequate key, removing dust and loose particles, thoroughly wetting the surface, applying cement mortar uniformly to the specified thickness, finishing the surface even and smooth without using extra cement, maintaining proper line, level, plumb and uniform thickness, curing and cleaning the adjoining surfaces, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 15 | Material and labour for preparing newly plastered or concrete ceiling surfaces by rubbing with sandpaper or other approved means to remove surface irregularities, dust and loose particles, including applying wall care putty of approved make such as Birla, JK or equivalent, to an average thickness of 3 mm in suitable coats, and smoothening the surface uniformly by using a mechanical sander machine fitted with a dust-suction arrangement to obtain an even and smooth finish, to the entire satisfaction of the Engineer-in-Charge; thereafter applying two coats of approved-quality interior emulsion paint of required shade and colour by paint brush or roller, including all necessary surface preparation, materials, labour, tools and tackles, allowing adequate drying time between coats, and leaving the finished surface uniform, smooth and free from brush/roller marks, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 16 | Material and labour for preparing old decorated ceiling surfaces, whether plastered or unplastered, by thoroughly removing and scraping all loose, flaking and deteriorated paint, dust, smoke soot, mould, moss, efflorescent salts, oil, grease and other foreign deposits using broom, steel patti, wire brush, sandpaper or other approved means; including cleaning, rubbing and smoothening the surface, and using a mechanical sander fitted with a dust-suction arrangement on uneven surfaces to obtain an even and smooth finish to the entire satisfaction of the Engineer-in-Charge; thereafter applying two coats of approved-quality oil-bound distemper (OBD) of required shade and colour by paint brush, including all necessary materials, labour, tools and tackles, allowing adequate drying time between coats, and leaving the finished surface uniform and free from brush marks, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 17 | Material and labour for preparing newly plastered or concrete surfaces of walls, pillars, cornices and similar surfaces having width or girth exceeding 10 cm, including rubbing the surface with sandpaper to remove minor irregularities, dust and loose particles; applying approved-quality wall care putty of approved make such as Birla, JK or equivalent, to a total thickness of 3 mm in suitable coats; smoothening the puttied surface uniformly by rubbing with sandpaper to obtain an even and smooth finish; and thereafter applying two coats of approved-quality plastic emulsion paint of required shade and colour by brush or roller, allowing adequate drying time between successive coats, to achieve a uniform, smooth and aesthetically pleasing finish to the entire satisfaction of the Engineer-in-Charge, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 18 | Material and labour for preparation of old painted surfaces (plastered/unplastered/concrete) of any description over 10cm girth or width, not otherwise described of of walls/pillars /cornices by brooming down or steel patti as required etc., and after preparing the surface applying two coats of plastic emulsion paint (finishing smooth and glossy upto entire satisfaction of Engineer-in-Charge) with using paint brush/roller brush, complete all as specified and as directed by Engineer-in-Charge. |
| 19 | Material and labour for preparing newly plastered or concrete surfaces of walls, pillars, cornices and similar surfaces having width or girth exceeding 10 cm, including rubbing the surface with sandpaper to remove minor irregularities, dust and loose particles; applying approved-quality exterior-grade wall care putty of approved make, such as Birla, JK or equivalent, to a total thickness of 1.5 mm to 2 mm in suitable coats; smoothening the puttied surface uniformly by rubbing with sandpaper to obtain an even and smooth finish; and thereafter applying two coats of approved-quality weatherproof exterior emulsion paint of required shade and colour by brush or roller, allowing adequate drying time between successive coats, to achieve a uniform, smooth and weather-resistant finish to the entire satisfaction of the Engineer-in-Charge, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 20 | Material and labour for complete removal of existing treatment (any layers of existing treatment) from walls/pillars/cornices by scraping down with using mechanical sander machine (including provision of dust sucking) upto entire satisfaction of Engineer-in-charge, brooming and washing down and preparing the surfaces smooth and after that applying two coats of weather proof exterior emulsion paint over 3mm thick wall care putty by using paint roller brush or electric paint spray machine, as per existing or as approved tint/colour complete all as specified and as directed by Engineer-in-Charge.Note : - Complete removal /scraping to old existing treatment as directed by Engineer-in-charge, each stage i.e after complete removal and before applying weather coats as specified above, the surface shall be passed in writing by the Enigineer-in-charge. |
| 21 | Dismantling and taking up existing floor hearth or wall tiling, including removal of tiles and cement mortar bedding, without disturbing or dismantling the backing/base masonry or concrete, carefully breaking and removing the existing tile work by suitable tools and equipment, collecting, loading, transporting and disposing of all dismantled tiles, mortar and rubbish material from the building premises and depositing the same in a low-lying vacant area at a location directed by AGE/JE, at a lead not exceeding 500 metres from the site, including all labour, tools, tackles and incidental operations, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 22 | Material and labour for providing and laying double-charged vitrified ceramic coloured floor tiles of approved make, light shade, 10 mm thick, square or rectangular in shape, with the area of each tile not exceeding 0.36 sqm, laid in approved pattern and design over and including 15 mm thick cement mortar bedding/screed in the proportion of 1:6 (cement : sand), properly prepared, levelled and finished to the required line, level and slope. The tiles shall be set and jointed in neat cement slurry, including all necessary cutting, edge trimming and fitting around corners, walls, columns, door openings and other obstructions as per site requirements; joints shall be neatly pointed with white or coloured cement matching the shade of the tiles, and the finished surface shall be cleaned and protected until completion, including all materials, labour, tools and tackles, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 23 | Material and labour for providing and fixing double charged vitrified ceramic coloured tiles of approved make, matching the floor tiles specified in the preceding item, light shade, 10 mm thick, square or rectangular in shape, as in skirting, dado and similar vertical surfaces, laid over and including 10 mm thick cement mortar rendering/bedding in the proportion of 1:4 (cement : sand), properly prepared and finished to the required line, level and plumb. The tiles shall be set and jointed in neat cement slurry, including all necessary cutting, edge trimming and fitting at corners, junctions, edges and around openings as per site requirements. Joints shall be neatly pointed with white or coloured cement matching the shade of the tiles, and the finished surface shall be cleaned and protected, including all materials, labour, tools and tackles, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 24 | Material and labour for Non Skid ceramic coloured tiles 7 to 8 mm thick square or rectangular area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer (screed) in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge. |
| 25 | Material and labour for Glazed ceramic coloured tiles of size 350mmx 250mm / 450mmX 350mm/ 450mmX 300mm, 7mm to 8mm thick, as in vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 10 mm thick (Av thickness) bedding layer (rendering) in cement mortar (1:4) complete all as specified and as directed by Engineer-in-Charge. |
| 26 | Demolition and taking up existing stone/marble slabs of any type, description and thickness, laid, bedded and pointed in any kind of mortar, as in floors, cooking platforms, steps, shelves, counters and similar locations, including breaking and removing the slabs along with the bedding and pointing mortar, carefully dismantling the work without causing damage to adjoining structures or surfaces required to be retained, collecting, lowering, loading, transporting and removing all dismantled materials and rubbish from the site, and depositing/disposal at the location directed by the Engineer-in-Charge, including all labour, tools, tackles and incidental operations, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 27 | Material and labour for providing and fixing 18–20 mm thick machine-cut granite stone slabs of approved type, colour and shade, factory-ground and polished (table-rubbed and polished), as in counter-sunk wash basin platforms, kitchen/cooking platforms, counters and similar locations, or as directed by the Engineer-in-Charge, including providing and laying a 15 mm thick screed/bedding layer in cement mortar (1:4) using grey cement, applying neat cement slurry for proper bonding, cutting, shaping, dressing and fitting the granite slabs to the required dimensions and profile, including necessary cut-outs for counter-sunk wash basins, sink openings, taps and other fittings, wherever required. The joints shall be pointed with white cement mortar (1:2) using marble dust and suitable pigment/admixture to match the shade of the granite, including grinding, edge finishing, cleaning and additional polishing wherever required to obtain a uniform, smooth and glossy finish, complete with all materials, labour, tools and tackles, in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 28 | Material and labour for dismantling and removing existing stone flooring of any type, including removal of existing bedding mortar, collecting and disposing of dismantled stone and rubbish as directed by the Engineer-in-Charge; thereafter providing and laying machine-cut Kota stone slabs, 18–22 mm thick, of size 550 mm × 550 mm, over and including 15 mm thick cement mortar screed/bedding in the proportion of 1:6 (cement : sand), properly prepared, levelled and finished to the required line, level and slope. The slabs shall be accurately cut, dressed and laid in the approved pattern, set and jointed in grey cement slurry mixed with suitable pigment to match the shade of the Kota stone, including filling and finishing of joints, rubbing, grinding and mirror polishing of the finished flooring to obtain a smooth, even and uniform surface, including all necessary cutting, edge finishing, materials, labour, tools, tackles and incidental operations, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 29 | Material and labour for dismantling and removing existing stone skirting of any type, including removal of existing bedding/rendering mortar, collecting and disposing of dismantled stone and rubbish as directed by the Engineer-in-Charge; thereafter providing and fixing machine-cut Kota stone slabs, 18–22 mm thick, as in skirting and similar vertical surfaces, over and including 10 mm thick cement mortar rendering in the proportion of 1:4 (cement : sand), properly prepared and finished to the required line, level and plumb. The Kota stone slabs shall be accurately cut, dressed and fixed to the required dimensions and profile, set and jointed in grey cement slurry mixed with suitable pigment to match the shade of the stone, including filling and finishing of joints, rubbing, grinding and mirror polishing of the finished surface to obtain a smooth, even and uniform finish, including all necessary cutting, edge finishing, materials, labour, tools, tackles and incidental operations, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 30 | Material and labour for providing and laying 10 mm thick coloured paver tiles (Endura Tiles) of approved make, shade and finish, size 300 mm × 300 mm, over and including 20 mm thick cement mortar screed/bedding layer in the proportion of 1:4 (cement : sand), properly prepared, levelled and compacted to the required line, level and slope. The tiles shall be accurately laid in the approved pattern, properly bedded and aligned, with uniform joints, including all necessary cutting, trimming and fitting at edges, corners and around obstructions. The joints shall be neatly filled and pointed with coloured cement matching the existing tile shade, and the finished surface shall be cleaned and protected until completion, including all materials, labour, tools, tackles and incidental operations, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 31 | Taking down carefully existing door/window/ventilator frames or chowkhats complete with shutters, without removing the shutters from their respective frames, including wooden/PVC door frames and steel ventilator frames, each opening having an area not exceeding 1.50 sqm, by cutting, breaking or removing the existing holdfasts and fixing arrangements as necessary, including cutting out masonry/concrete locally to release old, rusted holdfasts, removing the frames complete with shutters without causing undue damage to the adjoining masonry or structural members, clearing away dismantled materials and rubbish from the site, and preparing the exposed fixing locations and surfaces for installation of new holdfasts, including all labour, tools, tackles and incidental operations, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 32 | Material and labour for providing and laying 10 mm thick coloured paver tiles (Endura Tiles) of approved make, shade and finish, size 300 mm × 300 mm, over and including 20 mm thick cement mortar screed/bedding layer in the proportion of 1:4 (cement : sand), properly prepared, levelled and compacted to the required line, level and slope. The tiles shall be accurately laid in the approved pattern, properly bedded and aligned, with uniform joints, including all necessary cutting, trimming and fitting at edges, corners and around obstructions. The joints shall be neatly filled and pointed with coloured cement matching the existing tile shade, and the finished surface shall be cleaned and protected until completion, including all materials, labour, tools, tackles and incidental operations, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 33 | Supply and fixing of factory-manufactured, single-extruded WPC (Wood Polymer Composite) solid door frame/chowkhat of size 45 mm × 70 mm, manufactured using virgin suspension-grade polymer of K-value 58–60, calcium carbonate, natural fibres (wood powder/rice husk/wheat husk) and non-toxic additives, with maximum toxicity index of 12 per 100 g, having minimum density of 750 kg/m³, screw withdrawal strength of 2,200 N (face) and 1,100 N (edge), minimum compressive strength of 508 N/mm², modulus of elasticity of 900 N/mm² and Class A category resistance to spread of flame, with termite-proof, borer-proof, moisture-resistant and fire-retardant properties. The frame shall be accurately cut and fabricated with mitred joints, bonded using PVC solvent cement and secured with full-body threaded, star-headed stainless-steel screws. The complete frame shall be properly positioned, aligned, plumbed and fixed in the door opening using MS holdfasts/SS dash fasteners, including supply and fixing of 3 Nos. per frame, together with 100 mm long stainless-steel butt hinges, including taking down and removing the existing door frame, removal of old holdfasts, preparation of the opening, cutting and making good the disturbed masonry/plaster surfaces around the finished opening with cement mortar 1:4, finishing flush with the adjoining surfaces, and all necessary cutting, drilling, fastening, materials, labour, tools and tackles, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 34 | Supply and fixing of factory-manufactured, single-extruded WPC (Wood Polymer Composite) solid door frame/chowkhat of size 65 mm × 125 mm, manufactured using virgin suspension-grade polymer of K-value 58–60, calcium carbonate, natural fibres (wood powder/rice husk/wheat husk) and non-toxic additives having a maximum toxicity index of 12 per 100 g, with minimum density of 750 kg/m³, screw withdrawal strength of 2,200 N (face) and 1,100 N (edge), minimum compressive strength of 508 N/mm², modulus of elasticity of 900 N/mm² and resistance to spread of flame conforming to Class A category, having termite-proof, borer-proof, moisture-resistant and fire-retardant properties. The frame shall be accurately cut and fabricated with mitred joints, bonded using PVC solvent cement and secured with full-body threaded, star-headed stainless-steel screws. The complete frame shall be properly positioned, aligned, plumbed and fixed in the existing door opening using MS holdfasts/SS dash fasteners, including supply and fixing of 3 Nos. per frame, together with 100 mm long stainless-steel butt hinges, including taking down and removing the existing door frame, removal of old holdfasts, preparation of the opening and making good all disturbed masonry/plaster surfaces around the finished opening with cement mortar 1:4, finished flush with the adjoining surfaces, including all necessary cutting, drilling, fastening, materials, labour, tools, tackles and incidental operations, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 35 | Supply and fixing of factory-manufactured, single-extruded WPC (Wood Polymer Composite) solid plain flush door shutter, 30 mm thick, manufactured using virgin suspension-grade polymer of K-value 58–60, calcium carbonate, natural fibres (wood powder/rice husk/wheat husk) and non-toxic additives having a maximum toxicity index of 12 per 100 g, with minimum density of 650 kg/m³, screw withdrawal strength of 1,800 N (face) and 900 N (edge), minimum compressive strength of 50 N/mm² and resistance to spread of flame conforming to Class A category, having termite-proof, borer-proof, moisture-resistant and fire-retardant properties. The WPC solid flush door shutter shall be of approved make, quality and finish, accurately manufactured to the required size and dimensions, including necessary cutting, trimming, drilling and preparation of edges for proper fitting and installation in the door frame. The work shall include supply and fixing of 2 Nos. 150 mm long stainless-steel tower bolts and 2 Nos. 150 mm long stainless-steel handles per shutter leaf, complete with matching screws, fasteners and accessories, properly aligned and securely fixed, including all materials, labour, tools, tackles and incidental operations, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 36 | Supply and fixing of factory-manufactured 30 mm thick, 100% solid WPC (Wood Polymer Composite) wire-mesh door shutter of required size, manufactured by M/s RAJSHRI, an ISO 9001:2015 certified company, using virgin PVC resin of K-value 57–60 (suspension grade), calcium carbonate, natural fibres (wood powder/rice husk/wheat husk) and non-toxic additives, manufactured through single-extrusion process using WPC foam sheet (inner core), having minimum density of 650 kg/m³, screw withdrawal strength of 2,000 N (face) and 1,100 N (edge), minimum compressive strength of 50 N/mm², modulus of elasticity of 850 N/mm² and resistance to spread of flame conforming to Class A category, with termite-proof, borer-proof, water/moisture-proof and fire-retardant properties. Both faces of the shutter shall be covered with PVC foil of minimum 14 microns thickness in approved design, colour and finish. The central panel area, excluding stiles and rails, shall be provided with combined mosquito mesh and expanded aluminium (XTN) mesh, properly cut and fitted to the required dimensions, securely fixed with self-tapping, round-headed screws at suitable intervals, with screws and exposed mesh edges covered using feathered PVC edge beading all around to provide a neat and finished appearance.The work shall include supply and fixing of the following stainless-steel hardware and accessories for each door shutter:(i) 03 Nos. 100 mm long stainless-steel butt hinges, complete with stainless-steel full-body threaded, star-headed countersunk screws.(ii) 02 Nos. 150 mm long stainless-steel barrel tower bolts of extruded section, ISI marked.(iii) 02 Nos. 125 mm long stainless-steel handles, ISI marked.(iv) 01 No. helical door spring of 300 mm length.The shutter shall be accurately cut, trimmed, fitted and properly aligned in the door frame, including all necessary drilling, screw fixing, hardware installation, edge finishing, adjustments and testing for smooth operation, complete with all materials, labour, tools, tackles, accessories and incidental operations, for internal, balcony and main doors, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 37 | Supply and fixing of factory-fabricated aluminium frames for doors, windows, ventilators and partitions, manufactured from approved-quality aluminium sections/channels of required sizes and profiles, with one or more rebates as required, finished with approved-colour powder coating of minimum coating thickness of 50 microns, including all necessary cutting, mitred/jointed fabrication, corner cleats, jointing cleats, brackets, aluminium connectors, screws, fasteners and other accessories required for proper assembly and fixing. The frames shall be accurately positioned, aligned, levelled and securely fixed in the existing openings, including taking down and removing the existing old and unserviceable frames, removal of old fixing arrangements, preparation of openings and making good disturbed surfaces wherever required, complete with all materials, labour, tools, tackles and incidental operations, complete in all respects, all as specified and as directed by the Engineer-in-Charge.Note :- Weight of aluminium section/aluminium channel shall be physically ascertained through a board of officers convened by Accepting officer and payment shall be made only after the actual weight at site. |
| 38 | Supply and fixing of factory-fabricated anodised/powder-coated aluminium door shutters made out of approved-quality aluminium sections weighing not less than 0.55 kg per running metre, finished with approved-colour powder coating of minimum thickness 50 microns, including cutting, fabrication, mitred joints, assembly and fixing of all necessary aluminium joining cleats, glazing clips, rubber/neoprene packing, anodised aluminium snap beading, screws and other required accessories. The work shall also include supply and fixing of suitable-size aluminium handles, 2 Nos. per shutter leaf, and aluminium hinges, 4 Nos. per shutter leaf, of sizes and specifications as directed by the Engineer-in-Charge, including fixing of glass/panel filling material (glass and other filling material shall be measured and paid separately), proper alignment, adjustment and smooth operation of the shutter, complete with all materials, labour, tools, tackles and incidental operations, complete in all respects, all as specified and as directed by the Engineer-in-Charge.Note :- (i) Aluminium chowkhat frame shall be measured and paid separately under appropriate item of BOQ as supply and fixing. (ii) Glass and other filling material in panels shall be measured and paid separately under appropriate item of BOQ. |
| 39 | Supply and fixing of factory-fabricated powder-coated aluminium shutters for windows, ventilators and partitions, manufactured from approved-quality aluminium sections weighing not less than 0.55 kg per running metre, finished with approved-colour powder coating of minimum thickness 50 microns, including cutting, fabrication, mitred joints and assembly, with all necessary aluminium joining cleats, glazing clips, rubber/neoprene packing, anodised aluminium snap beading, screws and other required accessories. The work shall also include supply and fixing of suitable-size aluminium handles, 2 Nos. per shutter leaf, and aluminium hinges, 4 Nos. per shutter leaf, of sizes as directed by the Engineer-in-Charge, including fixing and securing of glass/panel filling material in position, proper alignment, adjustment and smooth operation of shutters, complete with all materials, labour, tools, tackles and incidental operations, complete in all respects, all as specified and as directed by the Engineer-in-Charge.Note :- (i) Aluminium chowkhat frame shall be measured and paid separately under appropriate item of BOQ as supply and fixing. (ii) Glass and other filling material in panels shall be measured and paid separately under appropriate item of BOQ. |
| 40 | Supply and fixing of 5.5 mm thick ordinary-quality sheet glass of approved make, clear and free from cracks, scratches, bubbles and other visible defects, cut to the required sizes, with the area of each individual pane not exceeding 0.50 sqm, for glazing in doors, windows, ventilators and similar frames. The glass shall be accurately measured, cut, shaped and fitted into the prepared rebates of the frames, including necessary glazing beads, clips, rubber/neoprene gaskets, fixing accessories and fasteners, as suitable for the type of frame, ensuring proper seating, secure fixing and a neat finish, including cleaning of glass surfaces after installation, complete with all materials, labour, tools and tackles, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 41 | Supply and fixing of 25-micron thick solar control reflective window film of approved make, such as Greater Sun Controller or equivalent approved product, suitable for application on existing glass surfaces of doors, windows and ventilators, providing effective solar heat and glare reduction while maintaining adequate visibility and light transmission. The glass surface shall be thoroughly cleaned and prepared before application; the film shall be accurately measured, cut to the required sizes and applied uniformly to the glass using the manufacturer's recommended application solution and procedure, ensuring proper adhesion without air bubbles, wrinkles, creases, dust particles or peeling edges. The work shall include trimming, edge finishing, removal of excess solution, cleaning and all necessary materials, labour, tools and accessories, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 42 | Supply and fixing of surface-mounted hydraulic door closer, aluminium body, hydraulically regulated, universal type, Designation No. 3, ISI marked, suitable for door shutters having width from 851 mm to 1,000 mm and weight ranging from 61 kg to 80 kg, complete with standard arm assembly, mounting plate, fixing brackets, screws, fasteners and all necessary accessories. The door closer shall be securely fixed to the door shutter and frame in accordance with the manufacturer's recommendations, including adjustment of closing speed, latching speed and closing force to ensure smooth, controlled and noiseless operation, including testing and commissioning, complete with all materials, labour, tools and tackles, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 43 | Supply and fixing, in replacement, of 150 mm long floor-mounted door stopper of approved make, manufactured from aluminium alloy body and tongue, anodised finish, complete with hard-drawn steel spring mechanism, suitable fixing base, screws, anchor fasteners and all necessary accessories. The existing defective door stopper shall be removed, the floor surface prepared, and the new stopper securely fixed in position by suitable anchoring, ensuring proper alignment and smooth operation of the spring-loaded tongue for holding the door in the required position, including making good the disturbed floor surface, testing and commissioning, complete with all materials, labour, tools and tackles, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 44 | Supply and fixing of galvanised mild steel wire cloth, manufactured from galvanised mild steel wire of 0.56 mm nominal diameter, having an average aperture size of 1.18 mm, suitable for fixing in door, window, ventilator and other designated frames, including cutting and trimming to the required dimensions, properly stretching and fixing in position with tinned tacks or galvanised wire staples at suitable intervals, ensuring uniform tension and a neat, wrinkle-free finish, including all necessary overlaps, fastening arrangements, materials, labour, tools and tackles, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 45 | Supply and fixing, in replacement, of vitreous china wall-mounted European Water Closet (EWC) of approved make, colour and design, complete with concealed/embedded flushing cistern installed inside the wall, matching seat cover and lid, jet spray with flexible connection pipe and health faucet holder, and all necessary flushing and fixing arrangements. The work shall include dismantling and removal of the existing defective EWC and associated fittings, preparation of the mounting surface, securely fixing and aligning the new EWC with suitable brackets/bolts and accessories, providing all necessary inlet and outlet connections, connectors, flush pipe/fittings, rubber gaskets, washers, sealing materials and connection to the existing soil/waste outlet pipe, including making good the disturbed wall and floor surfaces, testing for leakage and proper flushing, and commissioning, complete with all materials, labour, tools and tackles, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 46 | Supply and fixing of vitreous china oval-shaped under-counter wash hand basin, white colour, approved make, size 595 mm × 420 mm × 200 mm, Cat Part No. CNS-WHT-705 of Jaquar or equivalent make, subject to approval of equivalency by GE and conformity with the makes specified in Appendix ‘A’ to PSS-II. The basin shall be accurately positioned and fixed/countersunk below the granite countertop, including providing suitable supports, brackets, clamps, fixing bolts, sealing and waterproofing arrangements, and making a neat and watertight joint between the basin rim and underside of the granite slab. The item shall include supply and fixing of fancy-type 32 mm waste coupling, waste pipe, necessary connectors, rubber washers, gaskets and other accessories, including connection to the existing waste outlet, testing for leakage and proper drainage, complete with all materials, labour, tools and tackles, complete in all respects, all as specified and as directed by the Engineer-in-Charge.Note:- Granite slab/countertop shall be measured and paid separately under the appropriate BOQ item. |
| 47 | Supply and fixing, in repairs, of fancy-type swan-neck pillar tap, made of cast copper alloy, chromium plated, fitted with capstan-type operating head and screwed-down high-pressure mechanism, with or without lettering indicating ‘HOT’ or ‘COLD’, having long screwed shank and fly nut, suitable for connection to 15 mm diameter iron pipe, including dismantling/removal of existing defective tap, cleaning and preparation of threaded connection, providing suitable PTFE tape/sealing material, fixing, alignment, making leak-proof connections, adjustment and testing for smooth operation and proper flow, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 48 | Supply and fixing, in replacement, of vitreous china full-stall type urinal, white colour, size 410 mm × 380 mm × 950 mm, of approved make and quality, including dismantling and removal of existing defective urinal, carefully positioning and fixing the new urinal in proper line, level and alignment, including necessary brackets, fixing bolts, screws, plugs and supports. The item shall include CP urinal spreader, CP connection pipe, grating, waste coupling/union for connection to discharge pipe and waste pipe, including all necessary washers, gaskets, connectors and accessories, making watertight connections to the existing flushing water and drainage arrangements, testing for leakage and proper discharge, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 49 | Supply and fixing, in repairs, of urinal spreader, chromium plated (CP), of approved colour and finish, suitable for connection to 15 mm diameter water-supply pipe, having a minimum weight of 60 grams, including dismantling and removal of existing defective spreader, cleaning and preparation of threaded connection, providing suitable PTFE tape/sealing material, fixing with necessary connectors, washers and accessories, ensuring proper alignment and water distribution, making leak-proof connections and testing for satisfactory operation, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 50 | Supply and fixing, in replacement, of rotationally moulded polyethylene (PE) water storage tank, white colour, 1000 litres capacity, cylindrical vertical type, triple-layered construction with closed top, of approved make and quality, including hoisting, placing and fixing securely in position on the existing prepared tank platform/support. The item shall include providing and making inlet and outlet connections with all necessary fittings, adaptors, sockets, unions, washers, gaskets and accessories, including 20 mm bore high-pressure PTMT ball valve, fitted with epoxy-coated aluminium operating rod and high-density polyethylene float ball, suitable for screwed connection to 20 mm bore iron pipe. The item shall also include taking down and removal of the existing unserviceable PVC water storage tank of capacity exceeding 500 litres but not exceeding 1000 litres, lowering carefully, handling and disposal/stacking as directed, making all connections watertight, adjusting the float valve for the required water level, and testing the complete installation for satisfactory operation, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 51 | Taking up or down carefully 20 mm diameter steel tubing/PPR pipework and connections, including dismantling of joints, fittings, clamps, supports and other accessories as required, without causing damage to the pipework or fittings intended for reuse. The item shall include cleaning, removal of rust, scale, dirt and other deposits, sorting and stacking of serviceable materials for refixing or transporting and depositing the dismantled materials in the designated departmental store, as directed. All necessary labour, tools, tackles and handling arrangements shall be included, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 52 | Supply and laying of 20 mm outside diameter CPVC pipe, SDR-11, of approved make and quality, including necessary plain CPVC SDR-11 fittings such as bends, tees, elbows, couplings, reducers and other fittings required for completing the pipework. The pipework shall be laid/fixed on walls, ceilings or in floors, as required, including cutting, threading/adaptor connections wherever required, jointing with approved CPVC solvent cement in accordance with the manufacturer's recommendations, providing necessary clamps, saddles, supports and fixing accessories, maintaining proper alignment and gradient, making connections to existing pipework and fixtures, and carrying out hydraulic pressure/leakage testing, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 53 | Cutting chases and making good to existing masonry, concrete or plastered surfaces, including cutting chases for concealed water-supply tubing, CPVC/GI pipes, electrical conduits and other concealed services, as well as cutting, pinning in and making good to facings, ends or edges of landings, steps, cills, sunshades, shelves, lintels and similar projections, not exceeding 10 cm in girth. The item shall include cutting to the required depth and profile, removing loose material and debris, fixing/pinning the concealed pipework or conduit where required, filling and making good the cut portions with cement mortar 1:3, finishing flush with adjoining surfaces and pointing neatly to match the existing finish, complete in all respects, all as specified and as directed by the Engineer-in-Charge.Note: Measurement shall be based on the actual length of chase/cutting carried out, not exceeding 10 cm in girth. Major structural cutting, reinforcement cutting and making good beyond the specified chase dimensions shall be excluded unless specifically ordered. |
| 54 | Supply and fixing, in replacement, of 600 mm long PVC flexible connection pipe, 15 mm nominal size, fitted with PTMT nuts at both ends, of approved make and quality, suitable for water-supply connections to sanitary fixtures and fittings. The item shall include removal of the existing defective connection pipe, cleaning and preparation of threaded connections, providing necessary washers, rubber gaskets and sealing accessories, connecting and tightening both ends, ensuring proper alignment without kinking or twisting, making leak-proof connections and testing under working water pressure, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 55 | Supply and fixing, in replacement, of 15 mm bore long-body bib tap, made of cast copper alloy, fancy type, chromium plated, fitted with crutch or butterfly handle with capstan head and screwed-down mechanism, suitable for screwed connection to 15 mm bore iron pipe or brass ferrule, of approved make Jaquar / Parryware / Hindware, subject to approval by the Accepting Officer. The item shall include dismantling and removal of the existing defective bib tap, cleaning and preparation of threaded connections, providing suitable PTFE tape/sealing material, fixing the new tap in proper alignment, making leak-proof connections, testing for smooth operation and satisfactory water flow, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 56 | Supply and fixing, in replacement, of hand shower (health faucet) with ABS body, of approved make and quality, complete with 1 metre long, 8 mm diameter flexible connection tube and wall-mounted hook/holder. The item shall include taking down and removing the existing old hand shower of any type, disconnecting the existing flexible tube, cleaning and preparing the water-supply connection, fixing the new health faucet and wall hook with necessary screws, plugs, washers, gaskets and connectors, connecting the flexible tube, ensuring leak-proof joints and proper operation, including testing for satisfactory water flow and spray, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 57 | Supply and fixing, in replacement, of 300 mm size corner glass shelf, made of toughened safety glass of approved thickness, shape, colour and finish, with smooth, polished edges, of approved make and quality. The item shall include taking down and removing the existing old shelf of any type, providing and fixing the new shelf with suitable corrosion-resistant supporting brackets, stainless steel screws, wall plugs, washers and other necessary accessories, drilling holes in the wall, ensuring proper level, firm support and secure fixing, making good the disturbed surfaces and cleaning the finished installation, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 58 | Supply and fixing, in replacement, of 15 mm bore angle valve/stop valve, made of cast copper alloy, fancy type, chromium plated, fitted with screwed-down high-pressure mechanism and crutch or butterfly operating handle, having screwed connections at both ends and suitable for 15 mm bore iron pipe, f approved make Jaquar / Parryware / Hindware, subject to approval by the Accepting Officer. . The item shall include dismantling and removal of the existing defective valve, cleaning and preparation of threaded pipe connections, providing suitable PTFE tape/sealing material, fixing the new valve in proper position and alignment, making leak-proof connections, checking the smooth operation of the valve and testing under working water pressure, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 59 | Supply and fixing, in repairs, of 600 mm × 450 mm bevelled-edge mirror, made of selected-quality 5 mm thick mirror glass, mounted on 6 mm thick commercial plywood backing and provided with an aluminium frame. The item shall include cutting and fixing the mirror to the required size, providing smooth and uniform bevelled edges, securely mounting the mirror on the plywood backing and aluminium frame, and fixing the complete assembly to the wall using wooden plugs, chromium-plated brass screws and cup washers, including necessary adhesives, fasteners and accessories, ensuring proper alignment, level and firm fixing, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 60 | Supply and fixing, in replacement, of 20 mm bore gunmetal/brass gate valve (globe or gate type, as specified), ISI marked, made of approved-quality cast copper alloy, fitted with iron wheel operating head and having screwed connections at both ends, suitable for connection to 20 mm bore iron pipes. The item shall include dismantling and removal of the existing defective valve, cleaning and preparation of threaded pipe connections, providing suitable PTFE tape or other approved jointing material, fixing the new valve in proper position and alignment, making leak-proof connections, checking smooth operation of the wheel and valve mechanism, and testing under working water pressure, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 61 | Supply and fixing, in replacement, of 15 mm bore gunmetal/brass gate valve (globe or gate type, as specified), ISI marked, made of approved-quality cast copper alloy, fitted with iron wheel operating head and having screwed connections at both ends, suitable for connection to 20 mm bore iron pipes. The item shall include dismantling and removal of the existing defective valve, cleaning and preparation of threaded pipe connections, providing suitable PTFE tape or other approved jointing material, fixing the new valve in proper position and alignment, making leak-proof connections, checking smooth operation of the wheel and valve mechanism, and testing under working water pressure, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 62 | Supply and fixing, in repairs, of 125 mm diameter chromium-plated (CP) grating dome, with or without waste hole, made of approved-quality metal, having a minimum weight of 40 grams, suitable for fixing to the existing wash basin, sink or sanitary waste outlet, as applicable. The item shall include taking down and removing the existing defective grating dome, cleaning and preparing the fixing surface, providing necessary screws, washers, nuts, sealing material and other accessories, securely fixing the new grating dome in position, ensuring proper fitment and free drainage of wastewater, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 63 | Supply and fixing, in replacement, of 20 mm diameter stainless steel drapery rod (curtain rod) of approved make, grade and finish, suitable for doors and windows, including decorative finials at both ends, suitable stainless steel supporting brackets, curtain rings/runners and necessary fixing accessories, as required for complete installation. The item shall include taking down and removing the existing unserviceable curtain rod and pelmet box, drilling holes and fixing the new brackets securely to the wall or supporting surface with suitable stainless steel screws, wall plugs and fasteners, cutting the rod to the required length, ensuring proper alignment, level and firm support, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 64 | Supply and fixing, in replacement, of mild steel (MS) chromium-plated soap tray, approximately 160 mm in length, of approved make, design and finish, complete with suitable supporting brackets. The item shall include taking down and removing the existing defective soap tray, drilling holes in the wall and fixing the new soap tray securely with chromium-plated screws and PVC wall plugs, including necessary washers and other fixing accessories, ensuring proper alignment, firm fixing and satisfactory finish, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 65 | Dismantling and taking down carefully existing wall and ceiling boards made of fibre, pulp, insulation material or similar materials, including insulation boards, slabs and blankets of any thickness, together with cover fillets, fixing battens, supports and associated fixing accessories, as applicable. The item shall include removing screws, nails, clips and other fasteners, carefully lowering the dismantled materials without causing damage to adjoining structures or services, collecting and removing debris, and stacking serviceable materials or disposing of unserviceable materials at the location as directed by the Engineer-in-Charge, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 66 | Supply and fixing, in replacement, of 5 mm thick solid PVC wall-lining panels with wood-grain printed decorative finish, suitable for internal wall panelling, in lieu of plain-colour PVC sheets, of approved make, shade, pattern and quality. The item shall include taking down and removing the existing boards/wall panelling, providing and fixing suitable supporting framework of approved material and section, properly secured to the existing wall, and fixing the PVC sheets to the framework with suitable screws, clips, adhesives and other approved fixing accessories. The item shall also include providing and fixing 5 mm thick PVC fillets of 35 mm width at joints, corners, edges and junctions to obtain a neat and uniform finish, including cutting, drilling, shaping, jointing, finishing, making good disturbed surfaces and removal of dismantled materials/debris as directed, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 67 | Supply and fixing of 605 mm × 605 mm grid framework for seamless false ceiling, made of galvanised iron (GI), powder-coated, comprising GI perimeter channels, intermediate channels, ceiling sections, suspension arrangements and necessary connecting accessories, complete with 600 mm × 600 mm × 6–7 mm thick ceiling boards having aluminium profile sheet on the top face and PVC profile sheet on the bottom face, fixed in the grid framework in accordance with the manufacturer's recommendations.The GI framework shall comprise the following components:(i) GI perimeter channel: 0.55 mm thick, having two unequal flanges of 20 mm and 30 mm and web of 27 mm, fixed to the surrounding walls with nylon sleeves and screws at 450 mm centre-to-centre.(ii) GI intermediate channel: 0.9 mm thick, having two equal flanges of 15 mm each and web of 45 mm, suspended from the soffit at approximately 900 mm centre-to-centre with GI cleats and steel expansion fasteners.(iii) GI ceiling section: 0.55 mm thick, not exceeding 1.2 m in length, having a knurled web of 50 mm, flanges of 26 mm each and lips of 10.5 mm, fixed to the intermediate channels with connecting clips at 457 mm centre-to-centre.(iv) Suspension arrangement: 4 mm diameter GI wire hangers, up to 1200 mm in length, including adjustment for proper level and alignment, fixed to the roof slab through ceiling cleats made of 40 mm × 3 mm GI flat, 60 mm long, with 12.5 mm diameter × 40 mm long expansion holdfasts.(v) Ceiling boards: 600 mm × 600 mm × 6–7 mm thick boards, comprising aluminium profile sheet on the top face and PVC profile sheet on the bottom face, accurately cut and fitted into the grid framework as per the manufacturer's specifications.The item shall include all necessary GI cleats, connecting clips, suspension wires, fasteners, screws, nylon sleeves, powder coating, cutting, fitting, levelling, alignment and finishing, complete with all materials, labour, tools and tackles, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 68 | Supply and fixing, in replacement, of mild steel cupboard shutter comprising two leaves with MS frame, fabricated in accordance with the Godrej pattern, using 20 gauge MS sheet for the frame (all around) and 21 gauge MS sheet for the shutter leaves. The assembly shall be complete with a three-way locking arrangement, brass lock with duplicate keys, chromium-plated (CP) handles and all necessary hinges, locking bolts, fittings and accessories. The item shall include cutting, bending, welding, fabrication, fitting and fixing of the shutters in the existing cupboard frame, including providing necessary nuts, bolts and other fasteners, embedding/fixing the required supports in PCC 1:2:4, wherever required, and applying one coat of red oxide metal primer followed by two coats of approved-quality spray-applied paint of approved shade, including surface preparation, finishing and adjustment of shutters for smooth opening and closing, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 69 | Material and labour for providing and fixing 18 mm thick pre-laminated WPC board, exterior grade (Grade-I), conforming to IS 14587, for kitchen cupboards, cabinets and shelves, including dismantling and removal of existing boards of any description and type. The item shall include cutting, sizing, shaping and fixing the WPC boards with suitable screws and necessary fixing accessories, providing 6 mm thick teakwood lipping to all exposed cut edges of the pre-laminated boards, including necessary adhesive and finishing. The work shall also include providing and fixing all necessary hardware fittings, hinges, handles, screws, fasteners and accessories required for proper functioning of cupboard shutters and cabinets, together with second-class hardwood plain fillets wherever required for support and fixing. The item shall include making necessary adjustments, ensuring proper alignment, smooth operation of shutters and shelves, finishing exposed edges and removal of dismantled material/debris, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 70 | Dismantling and taking down carefully existing plain or corrugated steel sheet roofing of any gauge or thickness, including removal of all associated fixing accessories such as screws, bolts, nuts, hooks, washers, clips and other fasteners, as required. The item shall include carefully detaching the sheets from the supporting framework without causing damage to the structural members, lowering, handling and stacking serviceable sheets and accessories at the location directed by the Engineer-in-Charge, and removing unserviceable materials and debris from the site as directed, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 71 | Supply and fixing of 0.50 mm thick pre-painted Galvalume corrugated steel sheets, manufactured from aluminium-zinc alloy coated steel base metal having minimum tensile strength of 550 MPa and metallic coating mass of AZ150, of approved colour, profile and finish, suitable for roof covering and wall cladding, including cutting, shaping, laying, aligning, providing necessary side and end overlaps and fixing securely in position with approved corrosion-resistant self-tapping screws complete with EPDM/neoprene sealing washers, ensuring proper alignment, adequate fastening and weather-tight joints, including all necessary accessories, labour, tools, tackles and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 72 | Supply and fixing of 0.63 mm thick plain galvanised mild steel (MS) sheeting, having zinc coating of 275 g/m², for forming and providing ridges, hips, valleys, gutters, drips and straight flashings, at any height up to four-storey buildings. The item shall include cutting, bending, shaping and dressing the sheets to the required profiles and dimensions, providing necessary laps and overlaps, and fixing securely in position with suitable L-type or J-type hook bolts, nuts, bolts, washers, wooden plugs and other necessary fixing accessories. The work shall also include welding, jointing, sealing and finishing of connections, including all necessary materials, labour, tools, tackles, scaffolding and access arrangements required for proper installation, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 73 | Taking down carefully existing rainwater pipes/SWR pipes of any size or pattern, including all associated fittings and accessories such as bends, heads, shoes, swan-necks, offsets, junctions, sockets, clamps, holder bats and fixing arrangements, as applicable. The item shall include dismantling of pipe joints and removal of clamps, brackets and fasteners, cleaning the pipes and fittings to remove dirt, deposits and other adhering material, sorting and stacking the serviceable materials for re-use and issue under the Schedule of Credit, and transporting and depositing the dismantled materials at the designated departmental store, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 74 | Supply and fixing, in replacement, of 110 mm nominal bore uPVC soil, waste and rainwater (SWR) pipe, Type-B, single-socketed, of approved make and conforming to relevant IS specifications, laid in floors or trenches in required alignment, line, level and gradient. The item shall include taking down and removal of existing pipes of any type or description, cutting and preparing pipe ends, providing and fixing new uPVC pipes with compatible rubber-ring joints, including necessary sockets, bends, junctions, fittings and accessories, as required for completing the installation. The joints shall be properly assembled with rubber rings and sealed/made good with cement mortar wherever required, ensuring watertight connections. The item shall also include connecting to existing pipework, testing for leakage and proper flow, handling and removal of dismantled materials and debris as directed, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 75 | Supply and fixing, in replacement, of 110 mm nominal diameter uPVC soil, waste and rainwater (SWR) pipe bends of any radius, Type-B, of approved make and conforming to the relevant IS specifications, suitable for connection with existing/new 110 mm uPVC SWR pipework. The item shall include dismantling and removal of existing defective bends, cutting and preparing pipe ends, providing and fixing new bends with compatible rubber-ring joints or approved jointing system as per manufacturer's recommendations, including necessary rubber rings, solvent cement (where applicable), jointing materials and accessories, ensuring proper alignment, gradient and leak-proof connections, testing for satisfactory flow and removing dismantled materials and debris as directed, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 76 | Supply and fixing, in replacement, of 110 mm diameter uPVC soil, waste and rainwater (SWR) branch piece, single Y-type, equal or unequal, complete with access door, Type-B, of approved make and conforming to relevant IS specifications, suitable for connection to existing/new uPVC SWR pipework. The item shall include dismantling and removal of the existing defective branch piece, cutting and preparing pipe ends, providing and fixing the new branch piece with compatible rubber-ring joints or approved jointing system as per manufacturer's recommendations, including rubber rings, access-door cover with gasket and fixing arrangement, necessary jointing materials and accessories, ensuring proper alignment, leak-proof connections and accessibility for inspection and cleaning, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 77 | Material and labour for providing and laying 75 mm thick cement concrete, Type B-2, in the proportion of 1:2:4, using 40 mm graded crushed stone aggregate, as sub-base, including preparation, cleaning and dressing of the existing bed, mixing concrete with approved materials in the specified proportion, laying to the required thickness, line, level and slope, proper spreading, compacting and ramming to achieve a dense and uniform surface, finishing the top surface even and true to profile, including necessary curing, complete in all respects, all as specified and as directed by the Engineer-in-Charge. |
| 78 | Taking down carefully existing copper/aluminium point wiring for light, fan and socket points, including all associated accessories and fittings such as switches, sockets, ceiling roses, wall brackets, light fittings, sunken boxes, conduits, casing-capping, wiring accessories and other connected components, as applicable. The item shall include safe isolation and disconnection of the electrical supply, dismantling of wiring and accessories without causing unnecessary damage to adjoining installations, removal of dismantled materials from the site and making good all disturbed surfaces of walls, ceilings and floors with suitable materials, including plastering and finishing to match the adjoining existing surface in texture and appearance, complete in all respects, all as specified and as directed by the Engineer-in-Charge. Please Enable Macros to View BoQ information |
| 79 | Taking down carefully existing copper/aluminium point wiring for light, fan and socket points, including all associated accessories and fittings such as switches, sockets, ceiling roses, wall brackets, light fittings, sunken boxes, conduits, casing-capping, wiring accessories and other connected components, as applicable. The item shall include safe isolation and disconnection of the electrical supply, dismantling of wiring and accessories without causing unnecessary damage to adjoining installations, removal of dismantled materials from the site and making good all disturbed surfaces of walls, ceilings and floors with suitable materials, including plastering and finishing to match the adjoining existing surface in texture and appearance, complete in all respects, all as specified and as directed by the Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 12, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 26, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysNov 28, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender