Defence Statutory Bodies & Commissions/Committees Closing in 11 days TDR #58508130

Tender For Special Repair To Bldg No T-13 And T-14 At Kalimpong Mil Stn Under Ge 867 Ews.

Issued by Statutory Bodies & Commissions/Committees · kalimpong, West Bengal
Tender Value
43.58 Lakhs
Estimated cost
Bid Submission
03 Dec 2026
11 days left
EMD
87160
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
kalimpong → West Bengal
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender For Special Repair To Bldg No T-13 And T-14 At Kalimpong Mil Stn Under Ge 867 Ews.

BOQ

Name of Work:- SPECIAL REPAIR TO BLDG NO T-13 AND T-14 AT KALIMPONG MIL STN UNDER GE 867 EWS.
Sl. No. Item Description
1Dismantling of Asbestos cement /GI Sheet (corrugated, semicorrugated/Plain sheet) as in roof covering, etc. complete all as specified and as directed.
2S&F Pre-painted galvalume aluminium zink coating GI based corrugated steel sheet of 0.50 mm thick of any colour having tensile strenght of 550 MPA as in roof covering /cladding to wall, fixed with self tapping screws, etc. complete all as specified and as directed by Engr-in-Charge.
3S&F Pre-painted galvalume aluminium zink coating GI based plain steel sheet of 0.50 mm thick of any colour having tensile stenght of 550 MPA as in ridge,eaves board valley fixed with self tapping screws, etc. complete all as specified and as directed by Engr-in-Charge.
4Dismantling of wall and ceiling boards of fibre, pulp, insulation, etc. or insulation boards of any thickness including cover fillets, etc. complete all as specified and as directed.
5S&F 5 mm thick plain colour PVC sheet in strips & Channel feathered at the edges for fixing on solid PVC Wall lining , insulated PVC wall lining, Ceiling and solid PVC Partition inclusive solvent cement and including frame work and fixing at site, etc. complete all as specified and as directed.
6S&F 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on wall to make PVC frame as per specification and drawing, etc. complete all as specified and as directed.
7Dismantling of wrought iron or mild steel work of any description, etc. complete all as specified and as directed.
8S&F Joist, channel, angle, flat iron or Tee sections, fixed independently with connecting plates, etc confirming to Fe 410-W of Grade-250 of quality A, etc. complete all as specified and as directed.
9S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats confirming to Fe-410-W , Grade-250 of quality A, etc. complete all as specified and as directed.
10Dismantling of timber scantling 40 sqcm and over in section, in any postion as in frame work, etc. complete all as specified and as directed.
11M&L for Second class clean sawn hard wood as scantlings, etc. complete all as specified and as directed.
12Taking down chowkhats or frame n.exc 1.50 sqm each with shutter without taking off shutters from the frame, etc. complete all as specified and as directed.
13Taking down chowkhats or frame exc 1.50 sqm but n.exc 4.00 Sqm each with shutter without taking off shutters from the frame, etc. complete all as specified and as directed.
14M&L for 2nd class hardwood plain, solid, straight chowkhats and frames wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, etc. complete all as specified and as directed.
15S&F 18/19mm thick block boards of interior grade-2 quality of decorative choice veneer on one face of board, etc. complete all as specified and as directed.
16S&F Anodised aluminium frame with powder coating with minimum thickness of powder coating 50 Micron for doors, windows, ventilators with one or more rebates including joining cleat for fixing, etc. complete all as specified and as directed.
17S&F Aluminium door shutters of aluminium section weighting 0.55 Kg/m including necessary jointing cleats, glazing clips, ruber nerprene packing, necessary tower bolts, handles of 2 Nos in each door, hinges, anodised aluminium snap beading fixed with screw, etc. complete all as specified and as directed.
18S&F Anoidised Aluminium grill (Anodised transperent or dyed to required shade according to IS :1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to existing window frame with C.P brass/stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, etc. complete all as specified and as directed.
19S&F Anodised aluminium window and ventilator shutters of powder coating of any colour, thickness of powder coating not less than 50 micron of fixed type without sash bar, aluminium section weighting 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading fixed with screws, etc. complete all as specified and as directed.
20S&F 6mm Toughned glass as in hinged doors, partitionss automatic doors and similar work including cutting to shape drillling holes, etc. complete all as specified and as directed.
21S&F 4 mm sheet glass of ordinary quality is ground or obscured or frosted on one side and glazing with oil putty in square exc 0.5 sqm in each pane, etc. complete all as specified and as directed.
22S&F 4 mm sheet glass of ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane, etc. complete all as specified and as directed.
23S&F Stainless steel wire clothm of 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, etc. complete all as specified and as directed.
24Dismantling floor, hearth or wall tiling including cement mortar bedding, backing and removing of rubbish materials, etc. complete all as specified and as directed.
25M&L for 10 mm thick Virtified Ceramic coloured tiles (Square/ Rectangular) of area of each tiles n.exc 0.36 sqm in floors and set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles including 15mm screed bed in CM 1:4, etc. complete all as specified and as directed.
26M&L for 350x250x7/450x350x7mm thick Glazed ceramic tiles as in vertical surfacesset and jointed in neat cement slurry and pointed in white or coloured cement to match tiles including 15mm thick rendering/back coat in CM 1:4, etc. complete all as specified and as directed.
27Demolition of brick work/stone masonry built in cement mortar including all quoins, arches, pillars, ashlars facings, dressed stone work and pre-cast concrete articles, etc. complete all as specified and as directed.
28M&L for old size sub Class B bricks, straight or curved on plan exc 6 m mean radius built in CM 1:6 having compressive strenght not less than 75 kg/Sq cm, etc. complete all as specified and as directed.
29Taking down cement plaster of any description on brick or stone walls including racking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and as directed.
30M&L for 15 mm thick rendering in CM 1:4 on fair face of brick or concrete surface and finished the surface even and fair without using extra cement, etc. complete all as specified and as directed.
31Demolition of cement concrete (unreinforced) in ground floor and pavings n.exc 15 cm thickness below or above ground level, etc. complete all as specified and as directed.
32M&L for 150mm thick PCC type B-2 (1:2:4) (using 40mm graded stone aggregate) as in sub base, etc. complete all as specified and as directed.
33Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for including cutting of reinforcement as required to facilliate demolition, etc. complete all as specified and as directed.
34M&L for RCC of nominal mix typeB-1 (1:2:4) (using 20mm grading stone aggregate) as in slab supported walls, beams and columns in floors, landings, balconies, canopies, deck slabs, as in shelves including necessary form work, etc. complete all as specified and as directed.
35M&L for 10mm dia and over TMT bars cut to length bent to required shapes, cranking, binding including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, etc. complete all as specified and as directed.
36M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer, etc. complete all as specified and as directed.
37M&L for preparation of old plastered surfaces of walls and applying one coat of cement base paint, etc. complete all as specified and as directed.
38M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, etc. complete all as specified and as directed.
39M&L for preparation of old steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint, etc. complete all as specified and as directed.
40Excavating over area n.exc 1.5m deep and getting out in hard soil, etc. complete all as specified and as directed.
41Removing of excavated soil n exc 50 m and depositing where directed at a level n exc 1.5 m above the staring point, etc. complete all as specified and as directed.
42M&L for PCC type D-2 (1:4:8) (using 40mm graded stone aggregate) as in foundations, filling and mass concrete, etc. complete all as specified and as directed.
43M&L for PCC type C-2 (1:3:6) (using 40mm graded aggregate) as in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts including caps and bases, etc. complete all as specified and as directed.
44M&L for stone boulder for plumb concrete laid dry and hand packed tightly as in retaining wall, etc. complete all as specified and as directed.
45M&L for RCC type B-1 (1:2:4) (using 20mm graded stone aggregate) as in Columns, pillars, piers, posts and struts including necessary form work, etc. complete all as specified and as directed.
46M&L for 20mm thick rendering in CM 1:4 on other than fair faces of pre-cast cement concrete masonary of wall and finish the surface even and fair without using extra cement, etc. complete all as specified and as directed.
47Taking down unserviceable copper/aluminium point wiring of any description including all fittings and fixtures (switch , socket, switch socket combination, lamp holder, ceiling rose, light fittings and regulator and making good the disturbed surfaces of wall, floor etc. to match with existing finishes, etc. complete all as specified and as directed.
48Dismantling and taking down unserviceable main switches, DBs of any type/size and making good the disturbed surfaces to match with the existing finishes, etc. complete all as specified and as directed by Engr-in-Charge.
49M&L for point wiring with two single core 1.5 sqmm PVC insulated, unsheathed, FRLSH cable, 1100 volts grade, ISI marked with multi stranded copper conductor with proper colour coding drawn through and including PVC conduit (medium grade) with all fittings and accessories ISI marked fixed to roof,Wall,ceiling etc incl provision of 1.5 sqmm PVC insulated, multistranded, unsheathed, copper conductor cable, FRLSH, ISI marked as earth continuity conductor (green in colour) connected to common earth dolly incl fixing of modular metal flush boxes of appropriate size & thickness fixed flush to wall with modular back plate and top cover for mounting switch, sockets etc including cutting chases for conduits & sinkings for modular boxes & making good the disturbed surfaces, matching to the existing one etc for one light/Exhaust fan point controlled by one, one way switch 5/6 Amps, etc. complete all as specified and as directed.
50Description all as per item No 49.00 here-in-before but for one light point controlled by two 2-way switches, with cables 1.5 sq mm, etc. complete all as specified and as directed.
51Description all as per item No 49.00 here-in-before but for one bell point controlled by one switch, etc. complete all as specified and as directed.
52Description all as per item No 49.00 here-in-before but for one 3 point 5/6 Amps switch socket outlet point controlled by one switch on the same board, etc. complete all as specified and as directed.
53Description all as per item No 49.00 here-in-before but for one 3 pin 5/6 Amps switch socket outlet point controlled by one switch on independent board, etc. complete all as specified and as directed.
54Description all as per item No 49.00 here-in-before but using 2.5 sq mm single core copper conductor cable of multistranded FRLSH PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 sq mm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly. incl modular white cover plate, etc. complete all as specified and as directed.
55S&F 6A Modular switch of 1 way, 1 module 230 Volts, 50Hz of ISI marked, etc. complete all as specified and as directed.
56S&F 16A Modular switch of 1 way, 1 module 230 Volts, 50Hz, of ISI marked, etc. complete all as specified and as directed.
57S&F 6A Modular Bell push of 1 module 230 Volts, 50Hz of ISI marked, etc. complete all as specified and as directed.
58S&F Bell Ding Dong electric AC 230 Volts single pole , etc. complete all as specified and as directed.
59S&F 6A Socket of 2/3 pin combined 2 module 230 Volts, 50Hz of ISI marked, etc. complete all as specified and as directed.
60S&F 6A/16A Socket of 2/3 pin combined 2 module 230 Volts, 50Hz of ISI marked, etc. complete all as specified and as directed.
61S&F 6A Modular switch of 2 way, 1 module 230 Volts, 50Hz, of ISI marked, etc. complete all as specified and as directed.
62S&F 65 X 50 mm Ceiling rose of surface bakelite, three terminal, etc. complete all as specified and as directed.
63S&F Modular lamp/Angle holder insulated body with back plate for batten fitting, etc. complete all as specified and as directed.
64S&F 10W LED retro fit B-22 holder base with poly carbonate body and aluminium heat sink invertor lamp, etc. complete all as specified and as directed by Engr-in-Charge.
65S&F 20W LED batten surface / wall mounted with specially designed powder coated aluminium housing, high optically efficient polycarbonate diffuser, in built electronic driver duly wired up to terminal block, power consumption 20W, system efficiency of ≥100 lumens/W, Ingress protection IP 20, colour rendering index CRI>80, driver efficiency>85%, power factor > 0.90, THD <20% as per IEC 61000-3-2, colour temp -6500K, surge protection 2.5 KV, 50,000 burning hrs (min), etc. complete all as specified and as directed by Engr-in-Charge.
66S&F 10W LED batten surface / wall mounted with specially designed powder coated aluminium housing, high optically efficient polycarbonate diffuser, in built electronic driver duly wired up to terminal block, power consumption 10W, system efficiency of ≥100 lumens/W, Ingress protection IP 20, colour rendering index CRI>80, driver efficiency>85%, power factor > 0.90, THD <20% as per IEC 61000-3-2, colour temp -6500K, surge protection 2.5 KV, 50,000 burning hrs (min), etc. complete all as specified and as directed by Engr-in-Charge.
67S&F in repairs 6W LED 3000/6500K slim, compact aluminium die cast dege panel, recess mounted round/Square fixture with opal diffuser and separate electronic driver, etc. complete all as specified and as directed by Engr-in-Charge.
68S&F in repairs 9W LED 3000/6500K slim, compact aluminium die cast dege panel, recess mounted round/Square fixture with opal diffuser and separate electronic driver, etc. complete all as specified and as directed by Engr-in-Charge.
69S&F in repairs 12W LED 3000/6500K slim, compact aluminium die cast dege panel, recess mounted round/Square fixture with opal diffuser and separate electronic driver, etc. complete all as specified and as directed by Engr-in-Charge.
70S&F in repairs 3W LED Bed side lamp black 3000K, etc. complete all as specified and as directed.Make/Cat part No : 48042 of Phillips or equivalent in Havells/Crompton.
71S&F in repairs 6W LED Picture light, etc. complete all as specified and as directed by Engr-in-Charge.Make/Cat part No : 30973 of Phillips or equivalent in Havells/Crompton.
72S&F 35W LED building security light fitting of 230V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection, etc. complete all as specified and as directed.
73S&F 1x9W/1X10W LED light fitting IP66 & IK09 integral LED Bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size including taking down old unserviceable fitting, etc. complete all as specified and as directed.
74S&F 9W LED lamp B22 base wall mounting, brushed nickel finish fixture with acrylic diffuser, etc. complete all as specified and as directed by Engr-in-Charge.
75M&L for sub main wiring along with earth wire of size two run of 4 sq mm + one run of 4 Sq mm earth wire single core PVC insulated cable with stranded copper conductor FRLSH including drawing into 25 mm PVC conduit concealed in wall/roof including taking down existing sub main wiring, etc. complete all as specified and as directed.Note:Three run of 4 Sq mm copper wire including one run of 25 mm of size PVC condute shall be measured as one unit length)
76M&L for sub main wiring along with earth wire of size two run of 6 sq mm + one run of 6 Sq mm earth wire single core PVC insulated cable with stranded copper conductor FRLSH including drawing into 25 mm PVC conduit concealed in wall/roofincluding taking down existing sub main wiring, etc. complete all as specified and as directed.Note:Three run of 6 Sq mm copper wire including one run of 25 mm of size PVC condute shall be measured as one unit length)
77S&F Sheet metal enclouser Double door for MCB DB,s Phosphatised Powder Painted with bus bar 100 Amps rated Single pole and neutral link of 12 way 240 Volts AC, concealed in wall, etc. complete all as specified and as directed.
78S&F Sheet metal enclouser Double door for MCB DB,s Phosphatised Powder Painted with bus bar 100 Amps rated Single pole and neutral link of 8 way 240 Volts AC, concealed in wall, etc. complete all as specified and as directed.
79S&F DP 40-63 Amp, Miniature Circuit Breaker (MCB) 240V, 10KA 'C' curve current carrying capacity in the MCB DB complete with connection testing and commissioning, etc. complete all as specified and as directed by Engr-in-Charge.
80S&F SP 5 To 32 Amp Miniature Circuit Breaker (MCB) 240V, 10KA 'C' curve current carrying capacity in the MCB DB complete with connection testing and commissioning, etc. complete all as specified and as directed.
81S&F in repairs of PVC modular box type with MCB protected socket comprising PVC insulated enclosure with inbuilt plug top and socket, complete with 10 No SP MCB of 20/25 Amp rating, 'c' curve suitable for 220-240 Volts AC supply, including making necessary electrical connections, testing and commissioning, etc. complete all as specified and as directed by Engr-in-Charge.
82S&F Exhaust fan made of steel body, AC single Phase, 230V of size 300mm sweep with, blades, and frame and louvers including all fixing arrangements including taking down existing Exhaust fan & deposit to MES Store, etc. complete all as specified and as directed.
83S&F Exhaust fan made of sturdy engineering plastic complete with louvers, shutter, voltage 230V, 50Hz, RPM 1200, copper winding of sweep 250mm includinng all fixing arrangements including taking down existing Exhaust fan & deposit to MES Store, etc. complete all as specified and as directed by Engr-in-Charge.
84S&F 25 Ltr capacity electric water heater (Geysor) storage type of wall hanging/mounting type with powder coated metallic body of BEE 5 Star rated with diamond glass lined inner tank with maximum operating pressure of 8 bars incuding factory fitted thermostat maximum 75 Celsius with automatic thermal cutout and multifunctional saftey valve inculding suitable nuts & bolts for fixing arrangement operates on 230V, maximum power consumtion -2KW, with all accessories and connection pipe of 15mm bore of 2 Nos of hot and cold water supply, geyser saftey cord including taking down old existing Geasers of any capacity and deposit to MES Store, etc. complete all as specified and as directed.Make: Havells or equivalent Racold, Bajaj
85Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm buried directly in ground ( earth pit not less than 2.25m deep bellow ground level ) with top edge of the plate not less than 1.5m bellow normal ground level, connected to galvanized earth lead wire 4mm dia. by means of galvanized iron or steel bolts , nuts , check nuts and washers, and connected to equipments as directed , including funnel with GI med grade watering pipe 20mm bore , wire mesh , charcoal or coke and common salt in alternate layers of 15cm compacted thickness all around the earth electrode , with concrete pit in PCC type C-1 (1:3:6) (using 20mm graded stone aggregate), GI light grade earth lead protection pipe, CI Frame and cover , including necessary excavation earth work in soft/loose soil and disposal of soil to a distance n.ecx 50m and necessary testing complete all as shown on electrical plate N0.3 of MES SSR Part-1, etc. complete all as specified and as directed.
86M&L for Advance encapsulated compound based Chemical earthing CPRI tesed maintenance free , pipein -pipe technology upgraded (Zinc & Alloy coated). , Zinc & Alloy coated (80 -100) microns with pure zinc (99.9%) & Alloy coating (200-250) microns.Earthing system conforming IS 3034. The outer and inner pipe should be 76.2mm and 41.9mm dia respectively of 3 mtrs long zinc coated with additional special alloy coating 300mm on top side for additional protection of the terminal . The annular space between the pipes to be filled up with Compact fill CF (Crystalline Conductive) mixture which should be machine pressed in the pipes not disintegrate or collapse when outer pipe corrodes . The inner pipe should be extended with terminals for connectivity.The job includes digging the pits , lowering the pipe in pipe earth electrode,filling of pure conductolite back filling compound (BFC Conductolite) having excellent moisture retaining capacity in 250 mm around the electrode min 4 bags of 25 KG per pit per unit. The BFC should be eco friendly it should not contain environmently hazardous material/metal having ROHS certification from NABL accredited lab.The earth pit should be provided with a FRP earth pit cover for protection and safe guard of terminals. The material of earth electrode should have good electrical conductivity & anti corrosion property in wide range of soil conditions. The job also include M & L for in PCC type C-1 (1:3:6) (using 20mm graded stone aggregate) around the FRP cover for support and foundation and colouring the PCC work with desired colour, etc. complete all as specified and as directed by Engr-in-Charge.Make : ASHLOK ( Model ASEEL-39 AC 3 mtr length 76.3 mm diaNote : (i) Design of earth electrode should be of pipein-pipe technology .(ii) The earth electrode shall be CPRI tested to with stand short current test for 60kA rms for 1.0 second and 150kA for peak current.(iii) Contarctor has to fill pure back fill compound 250 mm all around the earth electrode up to full depth of pit.(iv) Contarctor shall submit the test report of earthing after satisfactorily completion.
87S&F Earth continuity conductor or main earthing lead with copper strip of size 20x3mm, fixed to wall on batten or recesses or chases or burried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc,Insulator fixing on wall internal between below 1.0 Mtr, etc. complete all as specified and as directed.
88S&F 175x150x100mm size Test terminal box made out of 2mm thick hot dip galvanised sheet drilled and screwed including 4 Nos 125mm long hexogonal head screwed with test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 Nos. 8mm dia 25mm long hex. head screw, etc. complete all as specified and as directed. Please Enable Macros to View BoQ information
89S&F 175x150x100mm size Test terminal box made out of 2mm thick hot dip galvanised sheet drilled and screwed including 4 Nos 125mm long hexogonal head screwed with test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 Nos. 8mm dia 25mm long hex. head screw, etc. complete all as specified and as directed. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58508130
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE 43.58 Lakhs
LAST DATE 03-12-2026
Authority
Authority Name Military Engineer Services
Work Description Tender For Special Repair To Bldg No T-13 And T-14 At Kalimpong Mil Stn Under Ge 867 Ews.
Basic Detail
Tender No 8660/E8
Bidding Type Tender
Location
City kalimpong
State West Bengal
Key Dates
Publish Date 12 Nov 2026
Submission Date 03 Dec 2026
Open Date 05 Dec 2026
Finance
Tender Value 43.58 Lakhs
Tender Fee 500
EMD 87160
Exemption Available
Document List
1be7ca00-6cee-4485-a805-ababf6422728.html
BOQ_895703.xls
Tender.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 12, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 03, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 11 days
Dec 05, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 13 days

Tender Documents

Download All (ZIP) ↓
html

1be7ca00-6cee-4485-a805-ababf6422728.html

xls

BOQ_895703.xls

pdf

Tender.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender