Defence Statutory Bodies & Commissions/Committees Closing in 10 days TDR #58507945

Tender For Comprehensive Maintenance Of Md & Otm Accn And Repair Replacement Of Misc Br Wks In Md & Otm Accn At Samana Under Ge Af Jamnagar No 1

Issued by Statutory Bodies & Commissions/Committees · Jamnagar, Gujarat
Tender Value
49.75 Lakhs
Estimated cost
Bid Submission
02 Dec 2026
10 days left
EMD
99500
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Jamnagar → Gujarat
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender For Comprehensive Maintenance Of Md & Otm Accn And Repair Replacement Of Misc Br Wks In Md & Otm Accn At Samana Under Ge Af Jamnagar No 1

Corrigendum

Sr No Corrigendum Date Corrigendum Type New Submission Date
1 19-Nov-2026 Corrigendum No 1 BOQ 02-Dec-2026

BOQ

Name of Work:- COMPREHENSIVE MAINT OF MD & OTM ACCN AND REPAIR REPLACEMENT OF MISC BR WKS IN MD & OTM ACCN AT SAMANA UNDER GE AF JAMNAGAR NO 1
Sl. No. Item Description
1Demolition of brick / stone / PCC block masonry / RCC Jalli fixed in cement mortar including all quoins, pillars, arches etc., complete all as specified and directed by Engineer-in-Charge.
2Material and labour for providing pre-cast cement concrete type C1 (1:3:6) (using 20mm graded stone aggregate) solid building blocks exe 10 cm thick, in width (with plain or inter locking joints as directed) setting in Cement Mortar 1:6 complete in wall or pillars, complete all as specified and directed by Engineer-in-Charge.
3Taking down cement plaster in cement or cement lime mortar on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc, including removal of debries to a distance exc 1.5 km but n.exc 2 Km, complete all as specified and directed by Engineer-in-Charge.
4Material and labour for rendering 10mm thick on stone masonary/brick / concrete surface of walls in cement mortar 1:6, complete all as specified and directed by Engineer-in-Charge.
5Material and labour for preparing newly plastered surface and applying one coat of cement primer, Two coat of white cement based wall putty, rubbing the surface smooth and applying two coat of oil bound distemper of approved shade and quality, complete all as specified and directed by Engineer-in-Charge.
6Material and labour for rendering 5mm thick on concrete surface of Ceiling in cement mortar 1:3, complete all as specified and directed by Engineer-in-Charge.
7Material and labour for preparation of new decorated plastered or unplastered surfaces of ceilling and applying one coat of alkali resistant primer, wall care putty as specified and two coat of oil bound Distemper (White or tinted), complete all as specified and directed by Engineer-in-Charge.
8Material and labour for rendering 15mm thick on stone masonary/brick / concrete surface of walls in cement mortar 1:4, complete all as specified and directed by Engineer-in-Charge.
9Material and labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal esistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, complete all as specified and directed by Engineer-in-Charge.
10Dismantling of floor, hearth or wall tiling or stone slab laid, bedded & pointed in any mortar including demolition of cement mortar bedding or backing coat, including removal of debries to a distance exc 1.5 km but n.exc 2 Km, complete all as specified and directed by Engineer-in-Charge.
11Material and labour for rendering 10mm thick in Cement Mortar 1:4 on on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing for skirting/dado etc., complete all as specified and directed by Engineer-in-Charge.
12Material and labour for Screed bed or bedding layer of mortar 15mm thick for laying floor finishes in Cement Mortar 1:6, complete all as specified and directed by Engineer-in-Charge.
13Material and labour for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 300X 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, complete all as specified and directed by Engineer-in-Charge.
14Material and labour for Non-skid, coloured ceramic tiles 7 to 8 mm thick (Square / rectangular) polished area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors etc., laid over and pointed with coloured cement to match the tiles, complete all as specified and directed by Engineer-in-Charge.
15Material and labour for Non skid, ceramic tiles 7 to 8 mm thick (Square / rectangular) polished area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors /skirting etc., laid over and pointed with coloured cement to match the tiles, complete all as specified and directed by Engineer-in-Charge.
16Material and labour for light shade Vitrified Ceramic tiles 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and directed by Engineer-in-Charge.
17Material and labour for light shade Vitrified Ceramic tiles 10mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1 sqm, in floors /skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified and directed by Engineer-in-Charge.
18Material and labour for Green Marble work 15 to 18mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade, complete all as specified and directed by Engineer-in-Charge.
19Material and labour 18-20mm thick granite stone slab of any type (cut, table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like, bedded & jointed with grey cement slurry & pointing with coloured cement using marble dust with admixture of pigment to match with marble shade; laid over, complete all as specified and directed by Engineer-in-Charge.
20Roundening to the edge of stone slabs on edge such as plateform, steps and other similar situations, complete all as specified and directed by Engineer-in-Charge.
21Material and labour for Machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over & including 15mm thick screed bed in cement mortar (1:4), complete all as specified and directed by Engineer-in-Charge.
22Material and labour for Kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing over and including 10mm thick screed bed in cement mortor 1:4, complete all as specified and directed by Engineer-in-Charge.
23Demolition of cement Concrete of any description and in any position not otherwise specifically provided for, complete all as specified and directed by Engineer-in-Charge.
24Material and labour for plastering 10mm thick on concrete surface in Cement Mortar 1:4, finishing the surface even and smooth without using extra cement, including mixing only liquid water proofing compound as per manufacture instruction, complete all as specified and directed by Engineer-in-Charge.Note:- WPC will be measured & paid separately.
25Supply only integral water proofing chemical @ 200ml/Bag of cement, complete all as specified and directed by Engineer-in-Charge.
26Applying coating (02 coats) of Pidifin 2k (of Make Dr Fixit or equivalant) @ (not less than) 1.54 kg/ Sq.m in two coats on sunken surfaces of toilet & bathroom and similar situation all as recommended by manufacturers, complete all as specified and directed by Engineer-in-Charge.
27Material and labour for PCC 1:5:10 type E-2 (using 40 mm graded stone aggregate) as in fdn filling and mass concrete etc., complete all as specified and directed by Engineer-in-Charge.
28Supply and fixing 60cm long, 40mm dia Tubes, 'medium grade', galvanised, with all fitting; laid in wall for suken foor, complete all as specified and directed by Engineer-in-Charge.
29Taking up or down 15mm dia steel tubing and connections, including cleaning for refixing or removal from site, complete all as specified and directed by Engineer-in-Charge.
30Supply and fixing 20mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors, complete all as specified and directed by Engineer-in-Charge.
31Taking up or down 20mm dia steel tubing and connections, including cleaning for refixing or removal from site, complete all as specified and directed by Engineer-in-Charge.
32Supply and fixing 32mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors, complete all as specified and directed by Engineer-in-Charge.
33Cutting chases, pinning in, making good to facings on stone concrete, block or slab wall, where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20cm girth, complete all as specified and directed by Engineer-in-Charge.
34Supply and fix in repair 15mm size fancy type , Chromium plated Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed by Engineer-in-Charge.
35Supply and fix in repairs 15mm size fancy type brass chromium plated, long shank & cup (concealed type) 15mm bore dia Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed by Engineer-in-Charge.
36Supply and fix in repair 15mm dia size fancy type Chromium plated Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed in any bore dia., complete all as specified and directed by Engineer-in-Charge.
37Supply and fix in repair 15mm bore fancy type Chromium plated Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed in any bore dia., complete all as specified and directed by Engineer-in-Charge.
38Supply and fix in repair 15mm bore, swan neck, taps cast copper alloy capaston head CP, screwed down high pressure with or without lettered “HOT” or “COLD” with long screwed shanks and fly nuts screwed for iron pipes fixed, complete all as specified and directed by Engineer-in-Charge.
39Supply and fix in repairs 15mm angle valve brass chromium plated, fancy type, complete all as specified and directed by Engineer-in-Charge.
40Supply and fix in repair Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe), complete all as specified and directed by Engineer-in-Charge.
41Supply and fix in repair Vitreous China Urinal Flat back, Bowl type type minimum size 465X355X265 white (excluding flushing cistern, flush pipe and waste pipe), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe), complete all as specified and directed by Engineer-in-Charge.
42Supply and fix in repairs sinks made of stainless steel 1mm thick, kitchen or laboratory, with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including supply and fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed by Engineer-in-Charge.
43Supply and fix in repairs sinks with drainage board made of stainless steel lmm thick, kitchen or laboratory, with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed by Engineer-in-Charge.
44Supply and fix in reapir Kitchen plate rack made of stainless steel not less than 1mm thick with fixing acessories, overall size 600mm x 900mm x 250 mm, IN REPAIR, complete all as specified and directed by Engineer-in-Charge.
45Supply and fix in repair 15mm dia Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed, complete all as specified and directed by Engineer-in-Charge.
46Supply and fix in repair wall mounted PVC bathroom mirror cabinet with mirror door, internal shelves complete with screws, wall plugs and all fixing accessories, complete all as specified and directed by Engineer-in-Charge.
47Supply and fix in repair Toilet paper holder with flat recessed type stainless steel fixed to walls with chromium plated (CP) brass screws, complete all as specified and directed by Engineer-in-Charge.
48Supply and fix in repair chromium plated soap tray any type and fixed to plugs on wall with chromium plated brass screws, complete all as specified and directed by Engineer-in-Charge.
49Supply and fix in repair Chromium Plated Grating doom 100mm dia., complete all as specified and directed by Engineer-in-Charge.
50Supply and fix in repair vitreous china wash basin, white, flat back, size 550mm x 400mm fixed on and including cast iron cantilever bracket 32mm dia brass waste coupling and including waste fitting and union, complete all as specified and directed by Engineer-in-Charge.
51Supply and fix in repair Vitreous Cliina wash basin, angle back, size 400mm x 400mm white, excluding taps, waste, chain and plug and porcelain stopper but including brackets, 32 mm dia brass waste coupling and, waste fitting and union, complete all as specified and directed by Engineer-in-Charge.
52Supply and fix in repair vitreous china wash basin, white, Table top, size 540mm x 360mm x 115mm fixed on and including cast iron cantilever bracket 32mm dia brass waste coupling and including waste fitting and union, complete all as specified and directed by Engineer-in-Charge.
53Supply and fix in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and directed by Engineer-in-Charge.
54Supply and fix in repair vitreous china wash down water closet pan (pedestal pattern) white with CI 'P' or 'S' trap including water closet seat cover of plastic, jet etc.complete including necessary PVC waste pipe fitting, complete all as specified and directed by Engineer-in-Charge.
55Supply and fix in repairs vitreous China squatting pan of Orrissa pattern of approved make of size 580mm X 440mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe including lime concrete bedding and connection to antisyphonage pipe etc including making good to floor, complete all as specified and directed by Engineer-in-Charge.
56Supply and fix in repair 10 Litre capacity PVC symphonic action type flushing cistern, duel flush type (ISI Marked) low level with inlet ball valve, float and handle & PVC flush pipe, fixed in position and connecting, complete all as specified and directed by Engineer-in-Charge.
57Supply and fix in repairs PVC connection 15mm size with PTMT nuts of length 450mm, complete all as specified and directed by Engineer-in-Charge.
58Supply and fix in repair brass chromium plated shower rose 100mm of size with arme and with or without swivel joints to steel pipe or union, complete all as specified and directed by Engineer-in-Charge.
59Supply and fix in repair Tubular towel ring, 20mm dia, D type, 600mm long between flanges brass chromium plated, complete all as specified and directed by Engineer-in-Charge.
60Supply and fix in repair Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 190gms), complete all as specified and directed by Engineer-in-Charge.
61Supply and fix in repairs looking mirror of size 600mm x 450mm, selected quality 5mm thick including aluminium frame, mounted on 6mm thick commercial plywood and fixed to wall with wooden plug & chromium plated brass screws, complete all as specified and directed by Engineer-in-Charge.
62Supply and fix in repairs PVC waste pipe flexible type suitable for couplings 32 / 40mm dia and 750mm long, complete all as specified and directed by Engineer-in-Charge.
63Supply and fix in repairs brass CP waste coupling (half or full threaded) of 32 / 40 mm size, complete all as specified and directed by Engineer-in-Charge.
64Taking down chowkhats or frame exceeding 1.5 Sqm but not exceeding 4.0 Sqm each with shutters of any description (W/out taking off shutters from the frames) and removal from site, complete all as specified and directed by Engineer-in-Charge.
65Supply and fix framed work as in doors or gates or grills, grating of angle, channel, hollow section or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges; also fastening and fixing confirming to Fe-410- W(Gde-E-250) quality-A, complete all as specified and directed by Engineer-in-Charge.
66Supply and fix for factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube fixed in opening complete as per manufacturer's specifications, complete all as specified and directed by Engineer-in-Charge.
67Supply and fix Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed by Engineer-in-Charge.
68Supply and fix Factory Made Solid PVC Moulded Door Shutter with wood free EPS core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site, complete all as specified and directed by Engineer-in-Charge.
69Taking down shutter of any description exceeding 1.00 sqm and not exceeding 2.00 sqm each and removal from site, complete all as specified and directed by Engineer-in-Charge
70Taking down shutter of any description exceeding 1.00 sqm and not exceeding 2.00 sqm each and Re-fixing of shutters in same opening after resecuring or easing & adjusting, complete all as specified and directed by Engineer-in-Charge
71Supply and fix 30 mm thick 2nd class HW Glazed and skeleton door shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass / gauge, etc., sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a), fitted to chowkats, complete all as specified and directed by Engineer-in-Charge.
72Supply and fix 30mm thick. flush shutter, solid core construction with particle board core and ply woood face panels commercial type on both side, complete all as specified and directed by Engineer-in-Charge.
73Supply and fix 2nd class HW 30mm thick Plain, framed,panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified and directed by Engineer-in-Charge.
74Supply and fix 100mm size butt hinges, stainless steel Grade 304, satin/matt finish, with satinless steel hinge pin , fixed with stainless steel screws, complete all as specified and directed by Engineer-in-Charge.
75Supply and fix 250mm stainless steel sliding bolt Grade 304 with bright finished bolt not less than 12 mm dia including all necessary screws and fittings, complete all as specified and directed by Engineer-in-Charge.
76Supply and fix stainless steel Grade 304 handle of size 150mm, complete all as specified and directed by Engineer-in-Charge.
77Supply and fix stainless steel (Grade 304) tower bolt of specified size 300mm approved make, matt finish, of specified size, complete all as specified and directed by Engineer-in-Charge.
78Supply and fix in floor door stopper 140mm size of aluminium alloy body and tounge, anodised, with hard drawn steel spring, complete all as specified and directed by Engineer-in-Charge.
79Supply and fix galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aparture 1.18 mm and fixed with tinned tacks ro galvanised wire stapple, complete all as specified and directed by Engineer-in-Charge.
80Supply and fix in repair 300mm, ordinary MS rat tail rod pattern springs including roller and roller plate, complete all as specified and directed by Engineer-in-Charge.
81Supply and fix in repair 100 mm size butt hinges, stainless steel Grade 304, with stainless steel hinge pin , satin finish, fixed with stainless steel screws, complete all as specified and directed by Engineer-in-Charge.
82Supply and fix in repair 150mm long stainless steel Grade 304 barrel tower bolts of extruded section, complete all as specified and directed by Engineer-in-Charge.
83Supply and fix in repair 150mm in size stainless steel Grade 304 handle cast type anodized, complete all as specified and directed by Engineer-in-Charge.
84Supply and fix in repair 250mm stainless steel sliding bolt Grade 304 with bright finished bolt not less than 12mm dia including all necessary screws and fittings, complete all as specified and directed by Engineer-in-Charge.
85Supply and fix in repair 300mm, ordinary MS rat tail rod pattern springs including roller and roller plate, complete all as specified and directed by Engineer-in-Charge.
86Material and labour for preparing new surfaces of wood or wood based materials of any description not other wise described over 10 CM width or girth new or previously un treated wooden surfaces and applying one coat of pink primer and two coat of synthetic enamel paint, complete all as specified and directed by Engineer-in-Charge.
87Material and labour for preparing old surfaces of wood or wood based materials of any description not other wise described over 10 CM width or girth new or previously un treated wooden surfaces and applying two coat of synthetic enamel paint, complete all as specified and directed by Engineer-in-Charge.
88Supply and fix in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aparture 1.18 mm and fixed with tinned tacks ro galvanised wire stapple, complete all as specified and directed by Engineer-in-Charge.
89Supply and fix in repair 25mm dia stainless stel (SS 304) curtain rod of reuired diameter, complete with stainless steel bracket, end caps, screws and necessary accessories, including drilling and fixing in position complete in all respect, complete all as specified and directed by Engineer-in-Charge.
90Taking down chowkats or frame with shutter of any description (without taking out shutter from the frame) not exceeding 1.50 sqm each and removal from site, complete all as specified and directed by Engineer-in-Charge.
91Supply and fix aluminium powder coating of any color ( thickness of powder coating not less than 50 micron) frame for door, window and ventilators or similar wk with one or more rebate inc joining cleat for fixing in repair, complete all as specified and directed by Engineer-in-Charge.
92Supply and fix aluminium door shutters powder coating of any color ( thickness of powder coating not less than 50 micron), alumimnium section weighing min. 0.55 Kg/m including necessary joining cleats, glazing clips, rubbers packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc in repair, complete all as specified and directed by Engineer-in-Charge.
93Supply and fix aluminium window and ventilator shutters or aluminium partition, powder coating of any colour (Thickness or powder coating not less than 50 micron),fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc., complete all as specified and directed by Engineer-in-Charge.
94Supply and fix aluminium window and ventilator shutters powder coating of any color ( thickness of powder coating not less than 50 micron), side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, aluminium snap beading, screws, aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (2 no.), complete all as specified and directed by Engineer-in-Charge.
95Supply and fix aluminium three track Powder coated of any color (thickness of powder coating not less than 50 micron) sliding window with three sliding shutter, the size of outer frame three track 92 x 31.5x 1.20mm (using two track for glazed window shutter and one track for wire gauged), the section shutter size 37x 18x 1.2mm) and glazing with 4 mm thick glass (plain/floated) including all-around suitable rubber gasket and MS wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4mm and fixed on aluminum flat and inserted in the frame of shutter with tracking arrangement each sliding window shall be provided with one number handle including locking arrangement & 2 numbers’s sliding rollers of nylon with including all necessary fittings, complete all as specified and directed by Engineer-in-Charge.
96Supply and fix sheet glass 5.5 mm thick ordinary quality (plain/floated/frosted) and glazing with oil putty / wooden beads / aluminium glazing clip in square n.exc. 0.5 sqm in each pane, complete all as specified and directed by Engineer-in-Charge.
97Supply and fix sheet glass 4 mm thick ordinary quality (plain/floated/frosted) and glazing with oil putty / wooden beads / aluminium glazing clip in square exc. 0.5 sqm in each pane, complete all as specified and directed by Engineer-in-Charge.
98Supply and fix in repair Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and directed by Engineer-in-Charge.
99Supply and fix in repair door closer hydraulically regulated designation No 2, aluminium (Die cast) body, universal type suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 Kg, complete all as specified and directed by Engineer-in-Charge.
100Supply and fix in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, complete all as specified and directed by Engineer-in-Charge.
101Supply and fix 100 mm size mild steel body Mortise lock, vertical type, with 2 lever, fixed to aluminium door, complete all as specified and directed by Engineer-in-Charge.
102Supply and fix MS louvers of 80 mm wide & 4 mm thick frosted glass including aluminium louver patti for adjusting the louvers fixed in Aluminium ventilators with screws etc., complete all as specified and directed by Engineer-in-Charge.
103Supply and fix in reapir door closer hydraulically regulated designation No 2, aluminium (Die cast) body, universal type suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 Kg fixed, complete all as specified and directed by Engineer-in-Charge.
104Supply and fix in repair Double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, complete all as specified and directed by Engineer-in-Charge.
105Supply and fix in repair 100mm size mild steel body Mortise lock, vertical type, with 2 lever, fixed to aluminium door, complete all as specified and directed by Engineer-in-Charge.
106Supply and fix in reapir MS louvers of 80mm wide & 4 mm thick frosted glass including aluminium louver patti for adjusting the louvers fixed in Aluminium ventilators with screws etc., complete all as specified and directed by Engineer-in-Charge.
107Hacking out old broken glass (any thickness, size quality or description) from wooden / steel / aluminium frame, including punching or drilling out old glazing pins/spring clips, complete all as specified and directed by Engineer-in-Charge.
108Supply and fix sheet glass 5.5 mm thick ordinary quality (plain/floated/frosted) and glazing with oil putty / wooden beads / aluminium glazing clip in square n.exc. 0.5 sqm in each pane, complete all as specified and directed by Engineer-in-Charge.
109Supply and fix sheet glass 4 mm thick ordinary quality (plain/floated/frosted) and glazing with oil putty / wooden beads / aluminium glazing clip in square exc. 0.5 sqm in each pane, complete all as specified and directed by Engineer-in-Charge.
110Dismantling boarding any description fixed in any position with screws, complete all as specified and directed by Engineer-in-Charge.
111Providng and fixing kitchen cabinet made of 18mm thick moisture-resistant MDF board, including shelves and shutters finished with approved decorative laminate on both sides, including all necessary cutting, edge beading assembly and fixing in all respect, complete all as specified and directed by Engineer-in-Charge.
112Supply and fix 18/19 mm thick, Block boards, grade 2 quality, interior grade, commercial type, fixed with screws to timber or angle iron frame-work, complete all as specified and directed by Engineer-in-Charge.
113Supply and fix Continuous (piano) hinges, stainless steel, width of flaps (when open) is 30mm bright finish or electrogalvanised, complete all as specified and directed by Engineer-in-Charge.
114Supply and fix for magnetic catcher of plastic body with striking plate etc and fixed, complete all as specified and directed by Engineer-in-Charge.
115Supply and fix 100mm in size stainless steel handle Grade 304, complete all as specified and directed by Engineer-in-Charge.
116Supply and fix Hasp and staple, safety type 100mm, of stainless steel of grade 304 hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and directed by Engineer-in-Charge. Please Enable Macros to View BoQ information
117Supply and fix Hasp and staple, safety type 100mm, of stainless steel of grade 304 hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and directed by Engineer-in-Charge. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58507945
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE 49.75 Lakhs
LAST DATE 02-12-2026
Authority
Authority Name Military Engineer Services
Work Description Tender For Comprehensive Maintenance Of Md & Otm Accn And Repair Replacement Of Misc Br Wks In Md & Otm Accn At Samana Under Ge Af Jamnagar No 1
Basic Detail
Tender No 8467/E8
Bidding Type Tender
Location
City Jamnagar
State Gujarat
Key Dates
Publish Date 19 Nov 2026
Submission Date 02 Dec 2026
Open Date 01 Jan 0001
Finance
Tender Value 49.75 Lakhs
Tender Fee 500
EMD 99500
Exemption Available
Document List
454d1c73-e2b6-43bc-b446-a7b0442577ed.html
BOQ_895573.xls
PS.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 19, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 02, 2026
18:00 IST

Corrigendum-1 Issued

Clarifications on tender conditions and amendments issued.

Upcoming · 10 days
Dec 02, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 10 days

Tender Documents

Download All (ZIP) ↓
html

454d1c73-e2b6-43bc-b446-a7b0442577ed.html

xls

BOQ_895573.xls

pdf

PS.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender