Public Administrative Department Government Departments Closing in 0 days TDR #58506595

Tender For Construction Of Vikas Khand Rampur Factory Or Ragan Panchayat Madarpali Khas (Ranchor Footi) Or Runchor Dham Or Pass Rest House

Issued by Government Departments · Deoria, Uttar Pradesh
Tender Value
15 Lakhs
Estimated cost
Bid Submission
19 Nov 2026
0 days left
EMD
30000
Bank guarantee accepted
Document Fee
766
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Deoria → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender for Construction Of Vikas Khand Rampur Factory Or Ragan Panchayat Madarpali Khas (Ranchor Footi) Or Runchor Dham Or Pass Rest House

BOQ

Name of Work:- VIKAS KHAND RAMPUR KARKHANA KE RGAM PANCHAYAT MADARAPALI KHAS (RANCHHOR KUTI) KE RANCHHOR DHAM KE PASS VISHRAMALAY KA NIRMAN KARYA
Sl. No. Item Description
1Excavation of Foundation-Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: All kinds of soil DSR-2.8.1
2PCC Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)\\" (DSR-4.1.8)
3Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level DSR 5.1.2(Footinf ,column and plinth beam in 1:1.5:3 conc)
4Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) DSR 6.1.2
5Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) (DSR-6.4.2)
6Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand derived from natural sources : 3 graded stone aggregate20 mm nominal size derived from natural sources). DSR 5.3
7Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete . Thermo-Mechanically Treated bars of grade Fe-500D or moreDSR 5.22.6
8Cartage EarthEarth work in filling plinth with 5 Km. cartage earth As per D.S.R 2.25A
9Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. DSR -4.17
10Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge. for Angle iron door Chaukhats 40*40*5-D.S.R.-10.31
11Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessaryscrews Second class teak wood.30 mm thickAs per D.S.R-9.9.1.2
12Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc.complete :As per D.S.R-9.40.1.1
13Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws As per D.S.R- 9.21.1 35 mm thick
14Providing and fixing factory made 30 mm thick door shutter made ofsolid PVC foam profile. The styles & rails shall be of size 75 mm x 30 mm having wall thickness 5 mm. The styles, top & bottom rails shall have one side wall thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power. The styles and rails shall be reinforced with M.S. tubes of size 33 mm x 17 mmx 1 mm,painted with primer , all four corners of reinforcement to be welded or sealed. Solid PVC extruded bidding (push fit type) will be set inside thestyles and the rails with a cavity, to receive single piece extruded 5mmPVC sheet as panel. The styles and rails will be mitred cut and joint with the help of PVC solvent cement & self driven self tapping screws. Single piece extruded solid PVC lock rail of size 100 mm x 30 mm with wall thickness 5 mm & 15 mm integrally extruded in the middle of the lock rail & fixed with styles with the help of PVC solvent cement & self driven self tapping screws of size 100mm x 8 mm complete as per manufacturer's specifications and direction of Engineer-in-charge.Non decorative finishAs per D.S.R-9.124.1
15Providing and fixing cup board shutters with 25 mm thick veneered particle board IS : 3097 marked, exterior grade (Grade I), of approved make,including IInd class teak wood lipping of 25 mm wide x 12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of Engineer-in-Charge.With decorative veneering on one side and commercial veneering on other side As per D.S.R-9.130.1\\"
16Providing & fixing of Anodised aluminium handle 125mm) As per . DSR 9.96.2
17Providing & fixing of Anodisid aluminium Sliding door bolts (300x16mm) As per DSR 9.100.1
18Providing & fixing of Anodised Aluminium tower bolts (250x10mm) As per DSR 9.97.2
19Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm diasteel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.As per D.S.R-10.3
20Providing and fixing M.S. grills of required pattern in frames of windowsetc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding As per D.S.R-9.48.1
2112 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) DSR-13.4.2
2215 mm cement plaster on rough side of single or half brick wall of mix : 1:6 (1 cement: 6 coarse sand) (DSR-13.5.2)
236 mm cement plaster of mix :1:3 (1 cement : 3 fine sand) D.S.R Items No 13.16.1
2412mm thick plaster in 1:3 in cement and coarse sand and finish with neat cement finishing on the top of Roof As per D.S.R 13.7.1
25Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate As per D.S.R-11.3.1
26Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm[DSR-11.41.2]
27Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 600x600 mm. D.S.R. 11.46.2
28Marble work gang saw cut (polished and machine cut) of thickness 18 mm for wall lining (veneer work), backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust)with an admixture of pigment to match the marble shade (To be securedto the backing by means of cramps, which shall be paid for separately).Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble.Area of slab over 0.50 sqmAs per D.S.R-8.1.1.2
29Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. D.S.R. 13.80
30Wall painting with premium acrylic emulsion paint of interior grade,having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applyingadditional coats wherever required to achieve even shad and colour Two coats As per D.S.R-iTEMS nO-13.83.2
31Finishing wall with acrylic smooth exterior paints of required shade new work (two or more coat applied @1.67 ltr/10sqm over and including base coat of water proofing cement paints applied @2.20kg/10sqm As per S.O.R Page No-29 Items No-13.46.1
32Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture As per D.S.R-13.48.2
33Painting Steel work with Deluxe Multi Surface Paint togive an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufactureAs per D.S.R-13.48.3
34\\"Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever requiredWhite Vitreous china Orissa pattern W.C. pan of size580x440 mm with integral type foot rests:D.S.R-17.1.1\\" :As perD.S.R-17.1.1
35Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brasspillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap As per D.S.R-17.7.4
36Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required Single half stall urinal with 5 litre P.V.C. automaticflushing cisternAs Per D.S.R-17.5.1
37Providing and fixing PTMT Waste Coupling for wash basin and sink,of approved quality and colour.Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms As per D.S.R-17.69.2
38Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete Flexible pipe 40 mm dia As per D.S.R-17.28.2.2
39Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm nominal bore As per D.S.R-18.49.1
40Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893115mm nominal bore As per D.S.R-18.53.1
41Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100 mm inlet and 100 mm outlet Sand Cast Iron S&S as per IS: 1729 As per D.S.R-iItems No-17.60.1.2
42Providing and fixing PTMT soap Dish Holder having length of 138mm,breadth 102mm, height of 75mm with concealed fitting arrangements,weighing not less than 106 gms. As Per D.S.R-iItems No-18.65
43Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.As per D.S.R-17.31
44Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 25 mm dia nominal bore D.S.R-18.10..3
45Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including allCPVC plain & brass threaded fittings, i/c fixing the pipe with clampsat 1.00 m spacing. This includes jointing of pipes & fittings with onestep CPVC solvent cement and the cost of cutting chases and makinggood the same including testing of joints complete as per directionof Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.As per D.S.R-iItems No-18.80 15 mm nominal dia Pipes 18.8.1
4620 mm nominal dia Pipes 18.8.2
47Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.As per D.S.R-18.48
48Supply of U-PVC pipes (working pressure 4 kg / cm²) Single socketed pipe 75 mm dia As per D.S.R-items No 7188
49Supply of U-PVC pipes (working pressure 4 kg / cm²) Single socketed pipe 110 mm dia As per D.S.R-items No 7189
50Supply of uPVC coupler for UPVC drainage pipes 75 mm As per D.S.R-iItems No 7192
51Supply of uPVC coupler for UPVC drainage pipes 110 mm As per D.S.R-iItems No 7193
52Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever requiredKitchen sink with drain board 510x1040 mm bowl depth 250 mm As per D.S.R-17.10.1.1
53Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar tapsetc. including moulding, rubbing and polishing of cut edges etc. complete.As per D.S.R-8.5
54Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete As per D.S.R-8.4.
55Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cementon walls and bed concrete etc. complete as per standard design:Inside dimensions 500x700 mm and 45 cm deep for pipeline with one or two inlets As per D.S.R-19.30.2.1
56Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S. (non modular) bricks ofclass designation 7.5 As per D.S.R-19.32.1
57Centering and shuttering including strutting, propping etc. and removal of form: in Foundations, footings, bases of columns, etc. for mass concrete DSR 5.9.1
58SameAs item number 16 in Columns, Pillars, Piers, Abutments, Posts and Struts DSR 5.9.6
59Same as item number 16 in Lintels, beams, plinth beams, girders, bressumers and cantilevers As per D.S.R -5.9.5
60Same as item number 16 in Suspended floors, roofs, landings, balconies and access platform As per D.S.R-5.9.3
61Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter [DSR-12.41.2]
62Providing and fixing on wall face unplasticised- PVC moulded fittings/ accessories forunplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 mm bend [DSR-12.42.5.2]
63Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm [DSR-12.43.2]
64Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box forceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5mm thick M.S. sheet with its top surface hacked for proper bonding,top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shallbe made of 12 mm dia M.S. bar bent to shape as per standard drawingAs per D.S.R-iItems No-10.18
65Suly and fixing of Inuguration Post at site.
66Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular type switch, modular plate, suitable size G.I. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. 1.1 Group C1.10.3
67Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.D.S.R 2025 iItems No-1.12
68Supplying and drawing following sizes of FRLS/HFFR PVCinsulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.1.17 2 x 1.5 sq. mm 1.17.2
692 x 2.5 sq. mm 1.17.11
702 x 4 sq. mm 1.17.20
71Supplying and fixing following size/modules, GI box along with modular base & cover plate for modular switches in recess etc as required.1.27 1 or 2 module(75mm X 75 mm ) 1.27.1
72Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch,connection etc. as required. 1.31
73Supplying and fixing 3 pin 5 A ceiling rose on the existing junction box/woodedn block including connectionetc. as required. 1.33
74Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.As per Items No-1.25
75Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.1.24 5/6 A switch 1.24.1
763 pin 5/6 A socket outlet 1.24.4
77Brush Less DIrect Current (BLDC) Motor Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal( Aluminum alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al bodyPower Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, remote (prefreably mobile app based) for speed control and all remaining accessories including safety pin, nut bolts,washers,temperaturrise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Ceiling Fancompliant to IS 374:2019 fan Supply, earthingetc. complete as req. 900mm, service value ≥ 5.1 CM/Min/Watt, air delivery 130 CM/Min (Minimum) E As per D.S.R-2025 Items No 9.1.1
78Supplying and fixing following way, single pole and neutral sheet steel, MCB distribution board, 240 V on surface /recess complete with , tinned copper busbar, neutral busbar, earth bar, din bar, interconnections, powder painted including earthing etc. as required (But without MCB / RCCB / Isolators). 2.3 12 way, Double door2.3.3
79Supplying and fixing 5 amps. to 32 amps. rating, 240 volts `C' series, miniature circuit breaker (MCB) suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.2.10 Single Pole 2.10.1
80Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required 63 A Double Pole 2.12.2
81Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.1.26
82Supplying and fixing single pole, blanking plate in the existing MCB DB complete etc. as required.2.11
83Supplying and laying of aluminium conductor PVC insulated armoured served sheathed cable 1100 volts grade at the depth of 750 mm bellow ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on side and on top as directed by Engineer-Incharge ,complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 20.1 10 sqmm 2 core 20d1.2
84Supply and fixing of LED Tube Light with heavy Duty Metal Box type Tube Light Fitting 1x22 watt suitable for upto 1x22 watt LED Polycarbonate tube light complete Including tube suitable for both surface & suspended complete in all respect. 2620 system lumens,with fully covered diffuser type>120 lm/w PF>.95,THD<10%,CRI>80, sheet thickness min 0.8mm, Tube with aluminium heat sink, >300V over voltage protection,2.5 KV internal Surge protection, with 5 years Warrantee. 23.07 CAT. - AAA
85Supply and fixing of water tight oblong 10 Watt LED bulk head luminaire having pressure die cast housing with driver set confirming to IP 65 and above Protection. IK 08, High purity/transmisivity UV stabilized Non yellowish diffuser/refelctor for uniform light distribution, detachable driver set, open and short circuit protection, suitable for 24 Hr Continious Operation, complete in all respects. 1100 system lumens,>110 lm/W, PF>.95, THD<10%, CRI>70, with 3 years Warrantee.23.11CAT. - AA Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58506595
AUTHORITY Government Departments
TENDER VALUE 15 Lakhs
LAST DATE 19-11-2026
Authority
Authority Name Rural Engineering Department
Work Description Tender for Construction Of Vikas Khand Rampur Factory Or Ragan Panchayat Madarpali Khas (Ranchor Footi) Or Runchor Dham Or Pass Rest House
Basic Detail
Tender No 1505/RED DEORIA/E-TENDER/2026-27. DATED 02.11.2026
Bidding Type Tender
Location
City Deoria
State Uttar Pradesh
Key Dates
Publish Date 13 Nov 2026
Submission Date 19 Nov 2026
Open Date 20 Nov 2026
Finance
Tender Value 15 Lakhs
Tender Fee 766
EMD 30000
Exemption Available
Document List
b5f789f7-dd70-4ae3-868c-e8e7f5ce7564.html
BOQ_2292193.xls
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 13, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Nov 19, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Today
Nov 20, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 1 day

Tender Documents

Download All (ZIP) ↓
html

b5f789f7-dd70-4ae3-868c-e8e7f5ce7564.html

xls

BOQ_2292193.xls

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender