Tender For Renovation Of Auditorium Stage And Green Rooms At The Reserve Bank Staff College
Tender Value
36.16 Lakhs
Estimated cost
Bid Submission
01 Dec 2026
14 days left
EMD
72340
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chennai → Tamil Nadu
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Renovation Of Auditorium Stage And Green Rooms At The Reserve Bank Staff College
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling work: Carefully dismantling the following items in existing auditorium, with minimum disturbances to the surrounding office-space and temporarily stacking the scrap/ salvageable items at a place as directed by Bank’s Engineer including barricading the debris / work area and carting away the debris from the college premises at regular interval / as and when required and disposing off the debris/ rubbish at a place permissible as per prevalent local municipal norms, etc., complete. Rate shall be quoted on per job basis for entire work as lumpsum a) Existing old wall panelling including wooden door shutter with the base framework approximate area : 80 Sqm as directed by Bank’s Engineer and covered suitably for preventing spread of dust, etc. complete.b) Existing old wooden flooring along with base frame of approximate area in plan: 55 Sqm including the raceways after removal of electrical and network cables. as directed by Bank’s Engineer and covered suitably for preventing spread of dust, etc. complete. c) Existing old open MS square suspended frameworkof approximately 27 Sqm excluding electrical, light, AC and other electrical fixtures/fittings. Note: Bidders may visit the location to assess the quantum of framework to be dismantled, before bidding. |
| 2 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as directed by Bank’s Engineer and disposing off the debris/ rubbish at a place permissible as per prevalent local municipal norms including barricading the debris / work area. |
| 3 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as directed by Bank’s Engineer and disposing off the debris/ rubbish at a place permissible as per prevalent local municipal norms including barricading the debris/ work area. |
| 4 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as directed by Bank’s Engineer and disposing off the debris/ rubbish at a place permissible as per prevalent local municipal norms including barricading the debris/ work area |
| 5 | Dismantling and removing the existing brickbat coba/ cinder/ vermiculite-filling along with mortar, if any, laid underneath the concrete finishes of stage as the base/ filling material, disposing and carting away the debris out of the Bank's premises etc. as directed by the Bank's Engineer. |
| 6 | Civil works: Plain Cement Concrete (1:4:8)Providing and laying in position cement concrete of specified grade including the cost of centering and shuttering. Plain Cement Concrete 1:4:8 (one part of cement, four parts of sand and eight parts of hard broken stone) using 40 mm gauge hand broken hard broken granite stone jelly complying with standard specifications in foundations and basement. |
| 7 | 230mm thick Brick Work:Providing and laying brick work with common burnt clay machine- moulded perforated bricks of class designation 12.5 conforming to IS: 2222 in superstructure above plinth level in cement mortar 1:6 (1 cement: 6 coarse |
| 8 | Mix design Concrete for Reinforced Cement Concrete: Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work using cement content as per approved design mix as well as approved RMC Plant manufactured in fully automatic batching plant & transported to site of work in transit mixer for all leads having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering, finishing & reinforcement including cost of admixtures in recommended proportions as per IS:9109 to accelerate/ retard setting of concrete, improve workability without impairing strength & durability as per direction of Bank’s Engineer. (Note : (Note: Contractor is required to produce test-certificate/ batching certificate as issued by the RMC Plant.) |
| 9 | Steel Reinforcement: Providing, cutting, laying & fixing in position Thermo-Mechanically Treated (TMT) bars of Fe 500D grade, reinforcement, of approved configuration and approved make or equivalent confirming to IS 1786 including decoiling, cutting, hooking, bending, cranking, fabricating to required shape, placing in position and tying the system at each junction with soft drawn annealed G.I. binding wire of diameter not less than 1 mm complete as per specifications at all heights and location and obtaining approval from Bank’s Engineer. Note: The rate shall include for cost of supplying binding wires, concrete cover blocks etc. Reinforcement chairs, spacer bars as per standard norms or directed by Bank’s Engineer shall be considered in reinforcement measurement. |
| 10 | Scafffolding system: Providing and fixing double scaffolding system (cup lock type) on the interior side of building/ structure, upto 25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40 mm diameter M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Bank’s Engineer.Note:- (1) The elevational area of the scaffolding shall be measured for payment purpose. (2) The payment will be made once only for execution of all items in the scope of this tender. |
| 11 | Mild Steel Section for ceiling frame workProviding, cutting, straightening, making holes, fabricating by electric arc welding using ISI marked approved make welding rods/ riveting, hoisting and erecting in position approved quality and make, ISI marked M.S Rolled Steel structural members such as tubes, Channels, Angles, Tees etc. of dimensions as per site-requirements using approved make anchor fasteners, holdfasts, nuts & bolts etc of appropriate sizes and shapes as approved by Bank's Engineer, for frameworks, structural members of roof etc. as per the drawings including preparing shop drawings and getting them approved prior to fabrication etc, as directed by the Bank's Engineer. The rate shall include suitably machining / grinding the members / joints wherever required to remove the rust / extra weld and make the surface even and smooth. The rate shall also include hiring charges of machinery required for fabrication and erection, suitably preparing the surface by dusting/ buffing/ sandpapering/ to remove the mill scales/ rust/ foreign matter, providing and applying two or more coats of synthetic enamel paint of approved make and shade over two coats of Zinc Chromate primer etc as directed by the Bank's Engineer. The quantity of structural steel will be worked out based on the actual dimensions of the finished work at site and theoretical/ actual section weights of the member whichever is less. |
| 12 | Interior WorksScreed PlasterProviding and applying average 12-15 mm thick protective layer / plaster in cement mortar (1:3) including mixing integral waterproofing admixture of approved quality @ 100 ML / bag of cement including making 300 mm high half round watta at the junctions of floor and wall and keeping the surface rough to receive further finishing including curing and ponding with water for 7 days for testing etc. complete. |
| 13 | Wooden flooringProviding and laying premium quality engineered hardwood wooden flooring in the auditorium, 15 mm thick, consisting of 3–4 mm thick natural Oak/Walnut hardwood wear layer over multi-layer cross-laminated hardwood plywood core with factory-applied UV matt finish, conforming to EN 14342/EN 13329 or equivalent standards. The flooring shall be laid over 2 mm thick high-density IXPE acoustic underlay with 200-micron polyethylene moisture barrier, complete with approved click-lock/tongue-and-groove system, low-VOC polyurethane adhesive wherever required, expansion gaps, matching hardwood skirting (75 mm high × 15 mm thick), T-profiles, reducers, end trims, stair nosing, transition strips, expansion joint profiles, edge trims and all accessories.The work shall include preparation of the subfloor by cleaning, grinding and applying self-levelling compound wherever necessary to achieve a level tolerance of ±3 mm over a 2 m straight edge, cutting and fitting around columns, walls and service openings, finishing, protection of completed flooring, cleaning and handing over complete in all respects as per the approved drawings, manufacturer's specifications and the directions of the Bank’s Engineer. Basic Rate: ₹.6800.00/Sqm. |
| 14 | Wall partitionAluminium framework: Providing and installing/fixing in position truly levelled full-height partition using approved make 50 × 50 mm aluminium framework placed horizontally and vertically at maximum 600 mm c/c, with alternate vertical members extending from the finished floor level to the true ceiling in a single continuous length, rigidly fixed to the floor, walls and ceiling. All vertical framework members shall be of a single piece without any jointsPlywood on Both sides: The framework to have fixed with 18mm thick approved make BWR plywood on either side of the framework up to ceiling etc all as per details in the drawing. The work to be completed as per design. The rate shall include supply, fabrication, aluminium framework, cutting, fixing, joint treatment, sanding, polishing, all necessary hardware, accessories, scaffolding, labour, tools, transportation, wastage, cleaning and completion of the work in all respects as directed by Bank’s Engineer. |
| 15 | Wall PanellingAluminium framework: Providing and installing/ fixing in position truly levelled full-height partition using approved make 50 × 50 mm aluminium framework placed horizontally and vertically at maximum 600 mm c/c, with alternate vertical members extending from the finished floor level to the true ceiling in a single continuous length, rigidly fixed to the floor, walls and ceiling. All vertical framework members shall be of a single piece without any jointsPlywood on one side: The framework to have fixed with 18mm thick approved make BWR plywood on one side of the framework up to ceiling etc all as per details in the drawing. The work to be completed as per design. The rate shall include supply, fabrication, aluminium framework, cutting, fixing, joint treatment, sanding, polishing, all necessary hardware, accessories, scaffolding, labour, tools, transportation, wastage, cleaning and completion of the work in all respects as directed by the Bank’s Engineer. |
| 16 | Veneer FinishProviding and laying of 4mm thick veneer with melamine polish over a wall paneling BWR plywood and necessary grooves and levels respectively complete in all respect as per the design, drawings and specification.The completion of the work in all respects as directed by the Bank’s Engineer. The final cost per sqm shall be calculated on the visible elevation surface only. Basic price of veneer is ₹1500 per Sq.m excluding GST |
| 17 | Laminate FinishProviding and laying of 1mm laminate over a wall paneling BWR plywood and necessary grooves and levels respectively complete in all respect as per the design, drawings and specification. The completion of the work in all respects as directed by the Bank’s Engineer. The final cost per sqm shall be calculated on the visible elevation surface only. Basic price of laminate is ₹750 per Sqm excluding GST |
| 18 | Fluted teak wood profiling/ paneling: Providing and fixing decorative fluted wall profiling using seasoned, machine-finished Second-Class Teak Wood beadings measuring exactly 37mm wide × 18mm thick, installed with a strict, uniform clear interval of 12mm between successive caps. All teak strips must be pre-treated with anti-termite oil on unexposed faces and securely mounted onto the existing backing framework using industrial-grade wood adhesive and headless pneumatic pins. The completed fluted assembly (caps and internal grooves) must be filled with matching wood putty, sanded smooth, and finished with minimum of two coats of premium spray-applied Melamine polish (Matt). Rate Inclusions: Supply and wastage of 2nd quality teak wood, anti-termite oil, adhesives, fasteners, specialized joinery labour, complete melamine polishing, scaffolding, tools, and cleanup. All work must achieve perfect line, level, and plumb to the final approval ofBank’s Engineer. |
| 19 | Storage UnitProviding and fixing storage rack/cabinet, of approximate dimensions of 450 mm depth x 750 mm height, using 18 mm BWR plywood for vertical/ horizontal members and 12 mm BWR plywood back panel, finished with 1 mm laminate, matching edge band, drawers/shutters with glass wherever required, Hettich/Häfele or equivalent hardware, complete as directed by Bank’s Engineer. |
| 20 | Balustrade for front-end stage entry steps:Providing, fabricating and fixing 12 mm clear toughened glass, in the clear panels available below an SS handrail of section 50 mm x 50 mm x 1.5 mm (304 grade), SS end posts of section 32 mm X 32 mm x 1.5 mm SS fixed on a 100 mm x100 mm x 1.5 mm SS Flange, including 16mm SS solid pipes for guardrails at a spacing of not more than 450 mm c/c, including necessary finishing with grinding, polishing etc. The rate shall include etching with frosted films of approved make and design on the glass panels complete as directed by Bank’s Engineer. |
| 21 | B) Green rooms and passage areaDismantling work: Carefully dismantling the following items in existing Auditorium green room, toilet, passage area, with minimum disturbances to the surrounding office-space and temporarily stacking the scrap/ salvageable items at a place as directed by Bank’s Engineer and disposing off the debris/rubbish at a place permissible including barricading the debris /work area and carting away the debris from the college premises at regular interval / as and when required, to dumping yard as approved by municipal authorities, etc., complete. Rate shall be quoted on per job basis for entire work as lumpsuma) Dismantling of Gypsum false ceiling (Passage area) : Existing old false ceiling consisting of plain gypsum-board false-ceiling with the GI framework, wooden boards, etc. including framework of an approximate area: 8 Sqm excluding electrical, light, AC and other electrical fixtures/fittings.b)Dismantling of tile flooring/wall dado: Carefully dismantling of existing tile flooring Vitrified/ ceramic/ mosaic/ granite tiles/ granite slabs) along with all bed mortar upto RCC base slab level at all floor levels and disposing of the same from the premises and stacking the salvageable items at a place directed and disposing off the debris out of the Bank's premises at place permissible by municipal authorities, etc. complete as directed. Note: Care shall be taken not to disturb /damage the structural (load carrying) members, cleaning to receive fresh bed mortar and tiles. Approximate tile area: 26 Sqm (including flooring and skirting) passage and green rooms) |
| 22 | Washroom DismantlingDismantling bathroom cum WC: Carefully dismantling the existing floor tiles along with bed concrete and sunken portion filling and wall dado of mosaic/any stone/tiles/ IPS along with back plaster, bedding for full area and height of all walls including plaster above the tile level with chisel, cutting, etc. to expose the base surface of floor including old water proofing upto RCC slab/ brick surface , preparing the surfaces for receiving fresh plaster, cleaning and stacking the salvageable items at a place directed and disposing off the debris out of the Bank's premises at place permissible by municipal authorities including tools and plants viz. ladder, platform scaffolding, etc. complete as directed. Note: The rate shall include for providing dust /debris preventive net/curtains of appropriate material designed for the safe working, Care shall be taken not to disturb/damage the structural (load carrying) members. Approximate floor area of each Bath cum WC varies from 2.4m/1.45m X 1.5m (approx) |
| 23 | Plumbing DismantlingCarefully dismantling all the plumbing and sanitary fittings viz, EWCs, Wash basins, sinks, G.I./PVC/CI pipes (internal and external), taps, valves, high level CI flush tank with bracket, floor traps, gysers, including stacking the salvage items at place directed and disposing of the debris out of the Bank's premises, etc. complete as directed. Rate shall include for temporarily plugging water and wastewater lines and connecting back after the work for each Bath cum WC all the plumbing and sanitary items measured as one Job. |
| 24 | Cement PlasteringProviding and applying average 15mm thick (or to match the adjacent area plaster thickness) cement plaster in CM 1:4 (1 Cement : 4 Sand) added with approved make integral water proofing compound as per manufacturer specifications to walls, columns, ceiling, beams, pardis, etc., in line and level including dismantling the existing damaged plaster, disposal of debris out of Bank's premises, curing of new plaster, etc., complete as directed. |
| 25 | CPVC water lines : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes of 20 mm nominal diameter, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing where necessary. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including filling the grooves with cement mortar 1:4, testing of joints complete as directed. The cost shall be inclusive of making good any damages caused externally to the pipe joint of the vertical stack and closing any openings made in the brick wall for this purpose and making good the wall avoiding any possible water seepages from external side. No scaffolding charges will be paid additionally.Length of pipe including specials will be measured by center line in running meter for payment. |
| 26 | Nahani trap: Supplying and fixing approved quality and make PVC Nahani/ floor trap with long horns / multiple inlets with 100 mm diameter mouth and a minimum water seal of 20 mm including C.P. grating cover/ jaali of required size and quality, complete as directed by Bank's Engineer. The scope of work shall include joining, the pipes / fittings / specials / accessories etc, to one another, using approved quality and make solvent cement, to make the joints water-tight, and making a floor sump, having overall dimensions of 300 mm x 300 mm x 300 mm, around the trap, providing , batching, mixing, laying & consolidating, P.C.C 1:1.5:3, using approved quality, 20 mm and down size, graded granite metals, river sand and approved make portland cement, admixed with approved quality and make water proofing chemicals, used as per specifications of the manufacturer and Bank’s Engineer. |
| 27 | PVC Waste water lines: Providing and fixing 6 kg/cm2 minimum pressure PVC pipes of 75 mm nominal diameter of approved make including all plain & threaded fittings, of the same manufacturer of the pipes or approved equivalent and fixing the pipes in proper line and level including cutting chases in the wall/ floor for concealing the pipes if necessary, and connecting to external vertical stack / nearest manhole chamber (applicable for ground floor rooms), including fixing the pipes with necessary clamps / fasteners for the vertical stack on the external side complete. The rate shall be inclusive of cutting, jointing of pipes with fittings with solvent cement of approved quality, packing the openings with water proof cement mortar and making good the damages by necessary plastering including necessary refilling, scaffolding, testing of joints/ pipelines for leakage etc. all complete as directed by the Bank's Engineer.Length of pipe including specials will be measured by center line in running meter for payment. |
| 28 | Same as above but for pipe of nominal diameter 110 mm. |
| 29 | Vitrified tiles flooring: Providing and laying full body / double charged Vitrified polished tiles in floors using tiles of size 600mm x 1200mm (thickness to be specified by the manufacturer) or any other approved size with water absorption less than 0.08% and conforming to IS 15622 of approved make / brand in all colours and shades laid over 20mm or more thickness cement mortar 1:4 (1 cement: 4 coarse sand) including grey cement slurry @3.3 Kg/Sqm, grouting the joints with white cement mixed with matching pigments in all shapes and patterns. Rate shall include for wastages, tools and tackles, curing, cleaning, and protecting the flooring work with bubble/ gypsum sheet and removing the wastage after painting works, etc. complete as directed. Basic price of tiles is ₹750 per Sq.m excluding GST. |
| 30 | Providing and laying water proofing treatment in sunken portion of the bathroom cum wc consisting of the following: (i) Providing and applying two or more coats of approved make SBR based cementitious waterproof coating admixed with ordinary portland cement to the sunken portion of entire bathroom cum wc, etc. including verticals and side walls up to 600 mm height above the floor finish level. The rate shall include preparation of surface by scrapping and cleaning the surface with wire brush, sealing of all joints, corners, junctions of pipes and masonry with SBR modified cement slurry. The rate shall include necessary curing, testing, etc., complete as directed by the Bank’s Engineer. (ii) Providing and rendering 20 mm (average thickness) plaster using approved quality and make polymer modified ready mix plaster to the sunken / floor portion of bathroom cum WC including verticals, side walls up to 600 mm height above FFL. The rate shall include preparing the surface, curing, etc., complete as directed by the Bank’s Engineer.(iii) The treated areas shall be tested by water ponding (Water ponding test after application and curing of waterproof coating & plaster to the sunken / floor portion and second after rendering and curing of the top layer of plaster after laying brick bat coba) 72 hours and shall be got approved before proceeding with further works. Note: Payment for this item shall be applicable on the floor- area measured to the nearest centimetre. |
| 31 | Ceramic tiles flooring:Ceramic tile flooring for bathroom: Providing and laying 1st quality non-skid/ matt (rustic style) finish ceramic tile flooring conforming to IS: 15622 of approved make, in approved pattern, design and shade for flooring in bathroom using of tiles of approximate size of 300mm x 300mm (thickness to be specified by manufacturer) or any other size laid over average 20 mm bed mortar CM 1:4 (1 cement : 4 coarse sand), filling the joints with epoxy tile grout of matching shade or matching shade joint filler of approved make, laid to the required slope, cutting, curing, etc., complete all as directed by Bank’s Engineer. (Basic rate of tiles ₹ 650 per Sqm. excluding GST) |
| 32 | Wall dado:Glazed vitrified polished tile full height wall dado for bathroom-cum-wc, wash basin area: Providing and fixing 1st quality glazed vitrified wall dado tiles conforming to IS 15622 of approved make, in approved pattern, design and shade using tiles of approximate size 1200mm x 600mm (thickness as specified by the manufacturer) or any other size to wall dado in Bath room, pantry area of approved make all in line, level and plumb, filling the joints with epoxy tile grout of matching shade or cement joint filler chemical of approved make, curing, including finishing corners with pvc beadings, etc., complete all as directed. The rate shall include preparation of back surface by plastering (if required/ levelling) the same with CM 1:3 (1 Cement: 3 Sand) up to required thickness making rough to have required bonding and receive tiles including bonding coat of approved make and as per manufacturer’s specification. Basic price of tiles is ₹800 per Sqm. excluding GST. |
| 33 | Pre-polished granite counter slab:Providing and fixing 18mm thick size jet black polished granite slab for wash- basin counter of approximate size 1000mm x 600mm x 840mm (height), for placing counter top type wash basin and pillar cock of the following specifications: (i) The vertical support(s) (01 number) shall be made out of 2 numbers of 18 mm thick, machine cut, one side machine polished (exposed side) granite slabs having width of 600 mm, sandwiched together using C.M 1:3 & cement paste, shall be fixed true to plumb and line and shall rest fully on the R.C.C floor slab.ii) Providing and fixing top slabs of minimum 18 mm thick granite slabs in not more than two pieces, fixed over the vertical supports, with joints over the vertical supports, for counter to fix wash basin (providing and fixing of wash-basin considered under the item below) including inserting into wall dado by a minimum of 25 mm after making necessary machine cut grooves around with neccesary granite fixing adhesives and resting in true level over the vertical support slabs. The scope of work shall include cutting the slab and necessary grooves for fixing the pillar cock and wash-basin. iii) Providing and fixing 18mm thick front edge (facia patti), minimum 100 mm wide, to the platform slab and it shall project above the finished horizontal granite slab toping by 5 mm and the exposed edges of the same shall be cut, bull-nosed and polished to the approved profile. Plan/ elevational area in one-direction will be measured for payment. Basic price of granite slab is ₹ 2500 per Sqm. excluding GST. |
| 34 | Counter-top wash basinProviding and fixing the counter-top wash basin of approved make, including waste coupling, bottle trap, all necessary accessories/ fittings. etc., complete as directed by Bank’s Engineer. Basic price of counter-top basin along with accessories is ₹7000 each set excluding GST. |
| 35 | Providing and fixing long body sensor based Pillar cock of approved make including 15mm diameter 450 mm long high quality PVC/ braided connections with two number 15 mm nut washers and rubber washers and all necessary accessories/ fittings (extension, if any), etc all complete as directed (Basic price of Pillar cock and 15mm diameter 450 mm long high quality PVC/ braided connections ₹ 9000 excluding GST). Rate shall include all necessary accessories, tools, tackle etc. |
| 36 | Angular Stop cock: Providing and fixing CP finished angular stop cock of approved make including all necessary accessories (extension, if required) etc. all complete as directed by Bank’s Engineer (Basic price of stop cock ₹ 1000 excluding GST). Rate shall include all necessary accessories, tools, tackle etc. |
| 37 | Concealed stop cock: Providing and fixing Concealed type C.P. brass angle cock/ stop cock of 15mm with flange of Jaquar or any other approved equivalent make, model, etc complete. (Basic price for brass concealed and outer body excl. GST = Rs. 1250/-) Rate shall include all necessary accessories, tools, tackle etc. |
| 38 | EWC (single piece) : Providing and fixing EWC with Flush tank & seat cover (single piece) of approved make including bolts/ rawl plugs, clamps and concrete grouting, connecting pipe, with complete set of accessories, trap, etc. all complete as directed by Bank’s Engineer.(Basic price of EWC, flush tank & seat cover set with accessories ₹ 16000 excluding GST). Rate shall include all necessary accessories, tools, tackle etc. |
| 39 | Providing and fixing (i) Two way bib cock of approved make etc. complete as directed by Bank’s Engineer. (Basic price excl. GST ₹ 1000) (ii) Health faucet gun with hose and wall-holder of approved make etc. complete as directed by Bank’s Engineer (Basic price excl. GST ₹ 1100). Rate shall include all necessary accessories, tools, tackle etc. |
| 40 | Providing and fixing premium quality float glass bevelled edge mirrorof approximate area of 0.5 Sqm. eachwith SS studs above wash basin of approved size/ model and make (Basic price excl. GST ₹ 3000/ No.) etc. complete as directed by Bank’s Engineer. Rate shall include all necessary accessories, tools, tackle etc. |
| 41 | Gypsum board false ceiling: Providing and fixing false ceiling of approved make at all heights/ levels including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 g/ Sqm (both side inclusive) as per IS:277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm diameter x 50mm long with 6mm diameter bolts, other flange of cleat fixed to the angle hangers of 25 x 10 x 0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45 x 15 x 0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm diameter x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board of 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I): 2011 (Board with BIS certification marks) to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering up to 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, A/C diffusers, cut-outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Bank’s Engineer. Rate shall include application of 2 or more coats of interior emulsion paint over a coat of primer after necessary surface preparation etc complete. |
| 42 | 100 mm Gypsum CorniceProviding and fixing 100 mm wide decorative gypsum cornice at the wall and ceiling junction, made of high-strength reinforced gypsum of approved profile, fixed with approved gypsum adhesive, SS screws and GI clips/brackets wherever required. The joints shall be finished smooth with gypsum filler and the surface finished with one coat of primer and two coats of premium acrylic emulsion paint of approved colour and shade. The rate shall include supply, cutting, mitred joints, fixing, finishing, painting, all materials, labour, scaffolding, tools, transportation, wastage and completion of the work in all respects as directed by the Bank’s Engineer. |
| 43 | Repainting of walls/ any other surface with Luxury Plastic Emulsion Paint:Preparing the surface of the walls and ceilings of roof slabs, soffits / vertical sides of beams etc by thorough scrapping / mechanical buffing / sand papering & dusting to remove the loose layers / flakes of paint finishes, providing and applying required thickness of white cement based putty to fill up, level and smoothen the surface, providing and applying a coat of approved special primer, two or more coats of Luxury Plastic Emulsion paint, of approved make, shade and quality as per manufacturer's specifications, standard specifications of the Bank and as directed by the Banks Engineer. The rate shall include carefully opening up the cracks developed on the plaster in ‘v’ shape and filling it with approved quality and make crack filler materials compatible with existing surface to be painted. The rate shall also include all materials, labour, transport, tools & plants etc required for the finished work, all as per site conditions and disposing-off and carting away the dust / debris generated from the work he Bank’s premises as directed by the Bank’s Engineer. |
| 44 | C) Auditorium Seating areaCarpet Tiles Flooring: Providing and fixing approved make and shade carpet tiles of size 500 mm x 500 mm, total thickness 7.5 mm (+/- 0.5 mm), tufted high & low loop, 100 % solution dyed ecolyn nylon, minimum gauge 2.12 mm, with pile weight of minimum 580 gm/ Sqm conforming to ASTM standards for flammability and smoke density, laid over false/ raised flooring and ceramic/ concrete flooring using appropriate adhesive recommended including necessary surface preparation as recommended by the carpet tile manufacturer and in the approved pattern and layout as directed by Bank’s Engineer. Carpet tiles shall be finished/ terminated end to end at the room perimeter and at the step risers in proper line and level including cutting, wastages and finishing, self - levelling as may be required underneath with all accessories etc. complete as directed by Bank's Engineer. The work includes careful removal of existing carpet flooring till base make the surface ready for new carpet laying and carting away the old carpet from the premises. Finished area shall be measured for payment. Basic price of carpet tile excluding GST is ₹ 1386 per Sqm |
| 45 | Rebate for taking away all the scrap obtained from Sr. No. 01 to 44 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 12, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 01, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 14 daysDec 02, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 15 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender