Housing Urban and Rular Development Government Departments Closing in 15 days TDR #58505422

Tender For Construction Of New Court Room At 3Rd Floor Of New Judicial Court Complex At Nawanshahr Distt. Shaheed Bhagat Singh Nagar

Issued by Government Departments · Shahid Bhagat Singh Nagar, Punjab
Tender Value
2.45 Crore
Estimated cost
Bid Submission
03 Dec 2026
15 days left
EMD
4.91 Lakhs
Bank guarantee accepted
Document Fee
20000
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Shahid Bhagat Singh Nagar → Punjab
EMD Exemption
Not Available
Quantity
Not Available

Project Description

Tender for Construction Of New Court Room At 3Rd Floor Of New Judicial Court Complex At Nawanshahr Distt. Shaheed Bhagat Singh Nagar

BOQ

Name of Work:- Construction of New Court Room at 3rd floor of New Judicial Court Complex at Nawanshahr Distt. Shaheed Bhagat Singh Nagar
Sl. No. Item Description
1Dismantling brick work tile, masonry or tile lining
2Dismantling of concrete
3Stripping and Stacking
4Terracing consiting of tiles 22.86x11.43x3.83cm laid over 25 mm mud plaster 7.5 cm mud filling on another layer of 25mm mud plaster including two coats of bitumen laid hot at 1.65 Kg. /Sqm top of R.C.C. slab including grouting with cement sand mortar 1:4 and top surface to be left clean after wire brushing
5Cement concrete 1:2:4 gola 10cm x 10cm concave quadrant along junction of roofs with parapet wall finished smooth, where specially specified.
6Centering and shuttering for columns (Square or rectangular or poly gonal in plain)
7Centering and shuttering for sides and soffits of beam, beams, launching girders, bressumers, lintels.
8Centering and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc.
9Centering and shuttering for faces of walls, partitions, retaining walls and the like (vertical or battering including attached pilasters buttresses etc.
10Reinforced cement concrete M-25 mechanicaly batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in supersturcture.
11Extra rate for using computerized concrete batch mixing plant including carriage by transit mixer with in 1km lead .
12Cold twisted detormed (Ribbed/ Tor steel) Bars (Fe 500 grade as per IS 1786-2008) , for R.C.C works, where not including in the complete rate of RCC including bending and binding placing in position complete
13Providing & fixing 16 gauge stainless steel pipe railing of grade 304 duly fixed on steps with the help of bolts grouted on steps with hand rail andnewel post of 50mm dia Stainless steel pipe, Balusters of 40mm dia Stainless steel pipe and guard 3 Nos of 15mm dia Stainless Steel pipecomplete in all respect
14First class burnt brick work laid in cement sand mortar 1:5 in first storey upto 4 metres above plinth level
15115mm thick brick wall in cement sand mortar1:5 without reinforcement in superstructure
1612.5mm thick cement plaster 1:4.
1720mm thick cement plaster 1:4 in two coat work.
18Providing and Fixing of Copper Sheet 16 Gauge 350mm wide on expansion joint including covering with C. Concrete complete in all respect as per specifications.
19Providing and fixing 0.50mm thick aluminum sheet including cost of necessary fittings i.e. screws, etc. complete
20Screed of 50mm thick cement concrete 1:8:16 with stone aggregate 40mm gaugeto be laid below the topping using mechanical mixer for mixing of material
21Providing and laying vitrified floor tiles in different sizes in light colour shades made using Full Body Technology (thickness to be specified by the manufacturer) with water absorption’s less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 fine sand), complete. ( Full body vitrified tiles have pigment in entire body / thickness of tile which makes chips and scratches less noticeable and make na ideal choice for high traffic zones.)Size 600x600 mm
22Marble stone flooring with 18-20 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :
23Grouting the joints of flooring tiles having joints of 3 mm width, using 2mm to 3 mm gap using spacers and later this gap to be filled with cement based grout ) with Cement base grout and matching pigments etc., complete, including filling / grouting and finishing complete as per direction of Engineer-in-charge. a. Size 600x600 mm
24Supplying and fixing of Door Frame Chowkhat Rolled from (1.2mm GI sheet ) (80*50*37)mm Single Rebate
25Supplying and fixing of Window Frame Chowkhat Rolled from (1.2mm GI sheet ) (72*55)mm
26Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate z sections and other sections conforming to Is: 733 and IS : 1285 of Jindal, Hindalco, Mahavir or equivalent make approved by Engineer in Charge , fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC Plug/neoprene felt etc. aluminum sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, aluminum snap beading for glazing/paneling, C.P.brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-InCharge. (Glazing and paneling to be paid for separately)
27For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and labour for fixing of fittings wherever required including the cost of PVC Plug / neoprene gasket required
28Providing Polyester Powder coating 50 micron any coloured specified to alumnum section of various sizes including carriage of material from market to workshop & workshop to site of work.
29Galzed Window Shutter Section rolled From GI sheet 47*20)m
30Wire Mesh Shutter section 40 *22
31Float glass 5.5 mm thick
32Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in paneling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-In-Charge. Pre laminated particle board with decorative lamination on one side
33Providing and fixing beading 12*12 mm
34Factory manufactured flush door fixed in position iron hinges, etc (excluding the cost of any fittings other than specified abovebut including labour for fixing the same in position (Code : II Revision IS-2191 Part-I) 1973
35Cost of aluminum fittings complete for doors, windows such as tower bolts, handles,Stoppersandscrewetc. for these fittings (Excluding sliding bolt)
36Providing and laying Laminate wooden flooring (Grade AC4 or AC4+ laminates) 6 mm to 12 mm thick, having a good backing layer made up of plastic laminate or melamine, core made up of medium-density fiberboard (MDF),which is less resistant to impact damage and less resistant to being dented by heavy furniture, having a décor layer to give each floor its appearance and consisting of one or more sheets of paper impregnated with melamine resin and top wear layer having clear aluminum oxide finish that protects the decorative layer & imparts the desired level of sheen, from full gloss to low gloss, duly fixed to the base floor using adhesive as approved by the manufacturer.
37Providing and fixing mineral fibre false ceiling tiles at all heights With 16 mm thick beveled tegular mineral fibre Anti-microbial false ceiling tile of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflection > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm lengt
38Providing and fixing tiled false ceiling of specified materials of size 595x595 mm ( GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece..) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \\"T\\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceilin
39Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish
40Applying priming coat with metal primer on newsteelor ironworkincludingpreparationof surface.
41Finishing walls with Premium Acrylic smooth exterior paint with silicon additives of required shade with two or more coats applied @ 1.43litre/10 Sqm over and including basecoat of water proofing Cement Paint applied @ 2.20 Kg/10 Sqm
42Wall painting with plastic emulsion paint of approved brand and manufacturer to give an even shade (two or more coats)
43Preparation of plywood surface for painting including sand papering the surface and applying filling with approved quality fillers consisting of white lead, linseed oil, Varnish, and Chalk Mitti including finishing the surface to required finish complete.
44Applying pink primer or aluminum priming coat on wood work including preparation of surface knotting and stopping etc.
45Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade.
46Public Health Services Sub head -1 - Dismantling of existing fixtures Public bathroom;- Dismanteling of HCI Specials including cost of labour for dismantel lead joints with suitable tools complete in all respect (labour only) vent cowl 100 mm i/d
47vent cowl 75 mm i/d
48Dismanteling of GI pipes of diffrent diameter including cost of labour with suitable tools complete in all respect (labour only) 25mm i/d
4940mmi/d
50Dismantling brick work tile, masonry or tile lining In cement for Platform 3 nos. For HDPE tanks
51Dismanteling of HDPE Tank carefully to reuse and reshifting from site to tarrece including cost of labour and tools required complete in all respect (3x2000ltr)(labour only)
52Judges Bathroom Dismanteling of GI pipes of diffrent diameter including cost of labour with suitable tools complete in all respect (labour only) 25mm i/d
53Dismantling brick work tile, masonry or tile lining In cement for Platform 3 nos. For HDPE tanks
54Dismanteling of HDPE Tank carefully to reuse and reshifting from site to tarrece including cost of labour and tools required complete in all respect (3x1000ltr)(labour only)
55Dismanteling of AC's including cost of labour ,tool required at site complete in all respect. 4 Nos cassete type
565 Nos Split type
57Fire Fighting Dismanteling of MS Pipes of diffrent diameters in fire fighting arrangements carefully including cost of labour ,tool required at site complete in all respect.(labour only) 50 mm i/d
58100 mm i/d
59150 mm i/d
60Dismantling brick work tile, masonry or tile lining in cement for Platform 1nos. For HDPE tanks
61Dismanteling of HDPE Tank carefully to reuse and reshifting from site to tarrece including cost of labour and tools required complete in all respect (1x5000ltr)(labour only)
62Dismanteling of air vessel from site including cost of labour and tools required complete in all respect (labour only)
63Dismanteling of Butterfly valve from site including cost of labour and tools required complete in all respect (labour only)
64Dismanteling of gate valve including cost of labour and tools required complete in all respect (labour only) 25mm i/d
65Sub head -2 - Refitting of existing fixtures Public bathroom Refitting of HCI Specials including cost of labour for dismantel lead joints with suitable tools complete in all respect (labour only) vent cowl 100 mm i/d
66vent cowl 75 mm i/d
67Refitting of GI pipes of diffrent diameter including cost of labour with suitable tools complete in all respect (labour only) 25mm i/d
6840mmi/d
69Construction of Plateform complete as per specification & as desired by Enginer-in-charge for Construction of Platform 3 nos. For HDPE tanks
70Refitting of HDPE Tank carefully to reuse and reshifting from site to tarrece including cost of labour and tools required complete in all respect (3x2000ltr)(labour only)
71Judges Bathroom Refitting of GI pipes of diffrent diameter including cost of labour with suitable tools complete in all respect (labour only) 25mm i/d
72Construction of Plateform complete as per specification & as desired by Enginer-in-charge for Construction of Platform 3 nos. For HDPE tanks
73Refitting of HDPE Tank carefully to reuse and reshifting from site to tarrece including cost of labour and tools required complete in all respect (3x1000ltr) (labour only)
74Refitting of AC's including cost of labour ,tool required at site complete in all respect. 4 Nos cassete type
755 Nos Split type
76Fire Fighting Refitting of MS Pipes of diffrent diameters in fire fighting arrangements carefully including cost of labour ,tool required at site complete in all respect. (labour only) 50 mm i/d
77100 mm i/d
78150 mm i/d
79Construction of Plateform complete as per specification & as desired by Enginer-in-charge for Construction of Platform 1nos. For HDPE tanks
80Refitting of HDPE Tank carefully to reuse and reshifting from site to tarrece including cost of labour and tools required complete in all respect (1x5000ltr)(labour only)
81Refitting of air vessel from site including cost of labour and tools required complete in all respect (labour only)
82refitting of Butterfly valve from site including cost of labour and tools required complete in all respect (labour only)
83Refitting of gate valve including cost of labour and tools required complete in all respect (labour only) 25mm i/d
84Sub Head-3 Internal Sewerage System & internal water supply system Providing and fixing in position H.C.I. Soil waste vent or antisyphonage pipes to I.S.I. specification of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of lead jointing. 100mm i/d H.C.I. pipe lines laid complete
8575mm i/d H.C.I. pipe lines laid complete
86Providing and fixing in position H.C.I special for soil waste vent or anti syphonage pipes to I.S.I specifications of E.L.C manufacture or any other reputed firm including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining.qty as per Table Atached For 100mm i/d pipes Plain bend
87Door bend
88bend 45degree
89collor
90single junction with door
91P-trap
92For 75mm i/d pipes collor
93single junction with door
94door tee
95Providing & Fixing in position M.S or heavy flat iron clamps made out of M.S flat iron not less than 5 mm of the approved design for fixing C.I. soil waste, vent or antisyhonage pipes to walls complete in all respects including cutting and making good the walls and floors etc. and painting. M.S. Holder bats clamps for 100mm i/d H.C.I. pipes
96M.S. Holder bats clamps for 75mm i/d H.C.I. pipes
97Providing lead caulked joints to H.C.I. pipes and specials conforming to I.S.I. Specification (IS:1729) of approved make (to the approval of Engineer-in-charge ) including cost of lead yarn, fuel and tools etc. 100mm i/d (1.36 kg.)
9875mm i/d (1.13 kg.)
99Providing and fixing H.C.I. Floor traps conforming to I.S.I. Specification (IS:1729) of approved make (to the approval of Engineer-in-charge) of the self cleaning design with C.P. brass hinged grating with frame with or without vent arm and including cement concrete 1:2:4 under and around the floor trap where required upto floor level complete in all respects including cutting and making good the walls and floors,etc. minimum depth of water should be 150mm with a minimum seal 50mm. With 75mm i/d outlet shallow seal at First Floor
100Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing.Single Socket Type B Qty as per Table Atached 110mm o/d SWR UPVC pipe line laid complete
10190mm o/d UPVC pipe line laid complete
102Providing and fixing in position SWR UPVC specials for soil waste vent or anti syphonage pipes as per IS-14735 of approved make (to the approval of Engineer-in-charge) including cutting and wastage etc. cutting holes in walls roofs or floors etc. and making good to its original condition but excluding cost of lead joining. qty as per Table Atached For 110mm o/d pipes Door Elbow 90 Degree
103Vent Cowls
104Single Tee With Door
105P Trap/Floor Trap 110mm x 75mm Ground Floor
106P Trap/Floor Trap 110mm x 75mm 1st Floor
107Elbow 90 Degree
108For 90mm o/d pipes Door elbow 90 degree
109Vent Cowls
110Elbow 90 degree
111Single Tee With Door
112Cutting holes upto 23cm square through B.B. in cement walls or stone masonary wall in cement for pipes, and making good the same & finishing according to existing finish where required. Through wall 11.43 cm thick
113Through wall 22.86 cm thick
114CONCEALED IN WALL: Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes as per IS 15778 (ISI marked with the prior approval of Engineer-inCharge), having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing including jointing of pipes & fittings, with one step CPVC solvent cement and testing of pipes complete as per direction of Engineer-in-Charge. CPVC SDR 11 Pipe & fitting 16mm o/d
115SDR 11 CPVC pipes & fittings 20mm o/d
116CPVC SDR 11 Pipe & fitting 25mm o/d
117Providing, Laying , fixing & jointing of P.V.C. Pipes as per ISI-4985 (ISI marked with the prior approval of Engineer-in-Charge) along the Trenches and laying the same in Trenches to correct alignment and gradients, cutting, jointing and testing complete as per specifications. 110mm o/d 4kg/sqcm
118Providing ,laying, jointing, fixing and testing ISI Marked G.I. Pipe (as per IS 1239) BClass including cost of specials (such as tees, bends, sockets, elbows etc.) ,painting with anti corrosive bitumastic paint, testing, cutting, threading Inside building complete. 15mm i/d
11920mm i/d
120.25mm I/d
12140mm i/d
122Sub Head - 4 Sanitary Installation Providing and fixing in position Chinaware Indian Orisa water closet size 580x440 mm of approved make (to the approval of the Engineer-in-charge) consisting of 10 ltr. PVC flushing cistern ISI makred including cost of PVC long bend 32 mm dia complete in all respect and to the entire satisfaction of Engineer-in-charge.
123Providing and fixing in position Chinaware European type water closet P trap or S trap of approved make (to the approval of the Engineer in charge ) consisting of 10 ltr. PVC flushing cistern, PVC short bend 32mm dia including cost of seat cover complete in all respect and to the entire satisfaction of Engineer in charge.
124Providing and fixing in position Chinaware extended wall mounted E. W.C. type suite (size 66 x 46 x 77.5 cm ) with P trap or S trap of approved make (to the approval of the Engineer-in-charge) with or without 10 ltr.chinaware matching flushing cistern and seat cover complete in all respect and to the entire satisfaction of Engineer-in-charge.Chinaware wall mounted E.W.C without cistern including seat cover complete in all respect.
125Providing and fixing in position Metropole flush valve 32mm size dual flow (Concealed body) with exposed shut off provision and round plate complete in all respect.
126Providing and fixing jet spray with 2'-6\\" long PVC pipe.With PTMT nut
127Providing & Fixing in position C.P. Brass Hexa Nipple 15mm of approved make (to the approval of Engineer-in-charge ) complete in all respect.
128Providing and fixing in position vitreous Chinaware white lIndian make large flat back or angular lipped front urinal 375 x 390 x 590 mm of approved make (to the approval of the Engineer-in-charge) consisting of C.P. brass Urinal waste Coupling dome type 32mm outer length 75 mm , C.P. brass Urinal Spreader Ocular-Regular and C.P. brass tube connection 300 mm long complete.
129Providing and fixing partition for different type of urinals.Vitreous white Chinaware PartitionLarge partition size 75 x 16.5 x 36.5 cm
130Providing and fixing in position vitreous chinaware white lavatory suites of approved make (to the approval of Engineer-in-charge) consisting of C.P. brass waste 32mm dia with one C.P. brass pillar tap including RackBolt Screw Pair 115mm long complete in all respect. Size 49 cm dia (above counter round) qty as per Table Atached
131Size 550 mm x 400 mm x815mm qty as per Table Atached
132Providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.
133Providing and fixing in position C.P brass basin mixer without pop-up waste system with 450 mm long flexible hose of approved make (to the approval of Engineer-in-charge) instead of C.P. brass pillar tap complete in all respect.
134Providing and fixing vitreous chinaware standard pedestal of approved make (to the approval of Engineer-in-charge) for wash hand basin complete in all respect.
135Providing & fixing in position PVC flexible tube connection of approved make (to the approval of Engineer-in-charge ) complete in all respect.PVC tube connection of size 15 mm x 375 mm with PTMT nut Qty same as WC+WB+Urinal
136Providing and fixing P.V.C Waste Pipe Collapsiable 32mm complete in all respect. Qty same as WB+Urinal+ Drinking water (-) Bottle trap
137Providing and fixing in position C.P. brass, bottle trap 32mm dia with 40 mm seal of approved make (to the approval of Engineer-in-charge) complete in all respect. For Washbasin & Urinal
138Providing and fixing in position C.P. brass soap dish of approved make (to the approval of Engineer-in-charge ) fixed into wall with rawl plugs and C.P brass screws complete in all respect.
139Providing and fixing in position C.P. Acrylic shelf with C.P.bracket and guard rails of approved make (to the approval of Engineer-in-charge ) fixed in with rawl plugs and C.P brass screws complete in all respect.CP brass Acrylic Shelf size 560mmx130mm
140Providing and fixing in position towel rails / ring of approved make (to the approval of Engineer-in-charge ) fixed in with rawl plugs embedded in walls with brass screws complete in all respect.C.P. brass towel Rails size 15mm dia 610mm long
141Providing & Fixing in postion 15 mm i/d bib cock of approved make (to the approval of Engineer-in-charge )complete in all respect. C.P. brass Bib cock long nose/ long body without flange
142C.P. brass Bib cock foam flow without flange
143Providing & Fixing in postion stop cock / Angle valve (as approved by the Engineer-in-charge). C.P.brass 15mm Angle valve without flange.
144C.P.brass 15mm Concealed stop cock with flange For Jet Spray Connection
145Providing & Fixing in position C.P. Brass flange Dome of approved make (to the approval of Engineer-in-charge ) under various fixtures complete in all respect.
146Providing & Fixing in position C.P. Brass extension piece 25mm long to 100mm long of approved make (to the approval of Engineer-in-charge )with various fixtures complete in all respect. C.P. Brass extension piece, 25mm long to 50mm long
147Providing & Fixing in position 5mm thick bevelled edge mirror of superior glass (of approved make) complete with 4mm thick hard board backing fixed in with rawl plugs 50mm, C.P. brass screws and washers and S/S Studs on top complete in all respect (as required by the Engineer-in- Charge) Size 600mmx450mm
148Providing and fixing in position premium range C.P. Brass Fittings and accessories of approved make (to the approval of Engineer-in-charge ) complete in all respect.C.P. Brass Accessories: C.P. brass toilet paper holder with flap
149Providing & Fixing in position C.P./Aluminium Khunti of approved make (to the approval of Engineer-in-charge ) fixed into wall with C.P. brass screws and rawl plugs etc. complete in all respect.C.P. Brass khunti with 3 pegs
150Providing and fixing in position vitreous Chinaware white channel of approved make (to the approval of Engineer-in-charge) of size 600 mmx100mm including laying and fixing in cement concrete 1:2:4 complete in all respect.
151Providing and fixing in position SS Grab Bar Grade 304 of approved make (to the approval of the Engineer-in-charge) fixed in to wall with brass screws complete in all respect. 35mm dia 600mm (24”) long
15235mm dia 1200mm (48”) long
153Foldable U Type 762mm long
154Providing & Fixing in postion liquid soap container of approved make (to the approval of Engineer-in-charge ) complete in all respect. C.P. brass liquid soap container
155Sub Head-5 Flooring and wall tiles Screed of 50mm thick cement concrete 1:8:16 with stone aggregate to be laid below the topping using mechanical mixer of mixing of material.
156Extra Rate for Consecutive Floor
157Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg /sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/ sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. Area same as screed
158Providing and laying Anti skid Ceramic floor tiles of size 300x300 mm x 10 mm thick of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on flooring skirting and dado in 12.5mm thick cement plaster 1:3 in base and jointed with @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., completewhite cement slurry in joints including corners angles and beading. Public Bathroom & Judge Bathroom
159Extra Rate for Consecutive Floor
160Providing and fixing 1st quality ceramic glazed wall tiles Matt/Semi Matt/Glosy/Highly Gloss finish/Highlighter/emboss conforming to IS : 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of size 450 x 310 mm as approved by Engineer-in- Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:4 (1 cement: 4 fine sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shadecomplete.
161Extra Rate for thirdFloor
162Black Granite stone tiles 15mm to 20mm thick in skirting, risers of steps, dado walls and pillars laid in 12.5mm thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with neat cement slurry mixed with pigment to match the shade of stone, including rubbing and polishing including labour for fixing dowel pins and cramps. Public Bathroom
163Extra Rate for First Floor
164Sub Head -6 Air conditioning and Water cooler Providing & fixing in position Water Cooler without Stablizer of approved make (to the approval of Engineer-in-charge ) including carriage complete in all respect. Water Cooler Full Steel Body 40/80 ltr Capacity without Stablizer
165AUTOMATIC VOLTAGE STABLIZER: Supply and erection of Single phasecopper wound Automatic voltage stablizer of suitable capacity electronically controlled circuit with input voltage 140-260 volts single phase AC supply and output voltage 220 ± 5% volts single phase AC supply having main silicon core copper wound step up transformer with suitable nos. of turns on primary side and secondary side the transformer should be fully insulated inside the MS sheet box of suitable size. There should be power control relay and single pole MCB (C-curve, 10kA) of suitable capacity complete with internal copper wiring along with amp. meter and volt meter, high voltage cut off 280 volt input (240 volt output) and 90 volt maximum boost and overloadingprotection to be provided:- Automatic Voltage Stablizer 2 KVA
166Providing & fixing in position UV filter having flow rate 200 ltr/hr with 3 stage purification process having 16 watt UV lamp and 35 Watt power rating of approved make (to the approval of Engineer-in-charge ) including carriage and fixing in position complete in all respect.
167Providing & Installing split type wall mounted air conditioner capacity 1.5 tonne Carrier, Hitachi, Voltas, Blue Star, Daikin make with 4.00 KVA voltage stablizer, MCB arrangement for installing OD units on terrace including inlet and outlet copper tubes with proper insulation drainage arrangement cable link between ID unit and OD units stand for OD unit and concealing of Copper pipes and drainage pipe within building and installing charges complete in all respects Judge Retiring Room
168Providing & Installing Cassette type Air Conditioner capacity 3.0 tonne and out door unit complete in all respect . Court Room
169Petty Items pertaining to the installation of cassette type AC's . Providing & Fixing outdoor stand for mounting outdoor unit and wall stand complete in all respects on terrace within building and installation charges.
170Copper Refrigerant piping thickness-19 SWG Complete with fitting suction line insulated with 12mm. Superlon/Armaflex Suction line. This Shall include Making & Finishing of Holes in Wall, Chiseling & Finishing , pipe sleevers etc 6/8\\" + 3/8\\" Refrigerant pipe. For Judge Retiring Room & Court Already Laid to be extended
171Rigid PVC Drain pipe with 6mm Heation insulation complete with fittings, Utraps etc & as specified to Nearest toilet 32 mml Only In 3.5 & 4.00 Tonne Cassette Type AC's For Judge Retiring Room & Court
172Supply and erection of PVC insulated PVC sheathed (3 core) round flexible wire with copper conductor (FR) cable (ISI marked) confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:-( Only in 3.5 & 4.00 Tonne Cassette Type AC's Overall size 4 sq.mm (56/0.25mm), 3Core For Judge Retiring Room & Court Already Laid to be extended
173HEAD 2 : FIRE FIGHTING Providing, laying, fixing, testing and commissioning of 'C' Class heavy duty MS Pipe conforming to Indian Standard IS : 1239/3589 including fittings like tees, bends, sockets, elbows, flanges, tapers, nuts bolts, gaskets etc. fixing the pipe on the wall / ceiling with suitable clamps and painting with two or more coats of synthetic enamel paint of required shade complete in all respects. 150mm internal diameter
174100mm internal diameter
17550mm internal diameter
17632mm internal diameter
17725mm internal diameter
178Supplying, Laying, Testing and Commissioning of ISI marked BUTTERFLY VALVE PN 1.6, with Gun metal seal duly ISI marked complete with rubber insertion, nuts, bolts and washers, matching flanges of required thickness, etc. complete as per specifications. 100 mm i/d
179Supplying, Installation, Testing and Commissioning 63 mm dia gun-metal Branch Pipe (ISI marked) with 20mm (nominal internal dia) size Gun metal nozzle confirming to IS 903, suitable for instantaneous connection to interconnect hose pipe coupling as required.
180Supplying, Installation, Testing and Commissioning of First Aid-fire Hose reel with MS construction spray painted in post office red, confirming to IS 884 with upto date amendments, complete with rubber hose pipe (IS:444/1987) 20mm dia 30 meter long type- 2, hose reel Drum with bracket as per IS:884, 20mm dia GM nozzle and 20mm dia GM gate valve as required complete with G.I pipe connention with main pipe complete in all respect.
181Supplying, Installation, Testing and Commissioning of G.M Single headed hydrant valve with instantaneous Gun metal peet coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (TypeA) with blank Gunmetal Cap and chain including orifice plate made of 6mm th Stainless steel to keep the pressure not more than 3.5 per sqcm at any point complete in all respects.
182Supplying, Installation, Testing and Commissioning of RRL FIRE hose Type A, IS:636, 63mm dia x 15m long with gunmetal male & female couplings (ISI marked) bound & riveted to hose pipes with copper rivets and copper wire as required.
183Supplying, Installation, Testing and Commissioning of weather proof cabinet for hose fabricated out of 1.6mm thickness M.S. sheet with front glass door having locking arrangement, suitable to accommodate all the necessary pipes, accessories, fittings etc including painting the metal portion with one coat of ready mixed primer paint and two coats of synthetic enamel paint of approved shade and quality, sign writing etc. 750 mm wide x 600 mm high x 250 mm deep Size
184Supplying an Fixing Pendant / Upright type sprinkler with quartzoid bulb, operating temperature 68 / 79 degree centigrade of 15 mm dia orifice sprinler head to approved by UL/SN
185Providing and fixing of FIRE EXTINGUISHER, ABC Powder type (storedpressure) as per IS: 15683 complete with all accessories as per Manufactures Specification. ISI Mark complete in all respect. 6 Kg. Capacity
186Providing and fixing of FIRE EXTINGUISHER, CO2 type as per IS: 15683 complete with all accessories as per Manufactures Specification. ISI Mark complete in all respect 4.5 Kg. Capacity
187Providing and fixing Sprinkler flexible drops stainless steel SS 304 C/W ½ “ NPT on reducer thread, with Max. working pressure of 175 PSI , Test pressure 875 PSI ( BURST ) with branch line ( inlet ) 1” NPT female thread , 01 No reducer , 01 no nipple , 02 no side brackets, 01 no centre brackets etc. complete set , unbraided UL listed complete in all respect. 1000 mm length
188Supplying and Fixing Sidewall Sprinkler rated at 68 / 79 degree centigrade, quartzoid bulb type, 15 mm dia orifice sprinler head to approved by UL/SN complete in all respect.
189Providing Internal Electrical Installations RECESSED PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES: Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/ 25mm dia. (ISI Marked) recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for suitable number ofmodules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and CallBell), Steel Hooks, Sheet metal fan box (1.6mm thick shape hexagonal), Circular junction Boxes (Four way PVC 1½\\" deep for walls and CI 3\\" deep for ceiling), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc., including the cost of above material, cutting and filling up of chases (with finishing the surface):-Wiring fan point with sheet metal fan box
190Wiring light point
191Wiring call-bell point
192Wiring 3 pin 6 Amp. wall socket point
193Wiring 3 Pin 6 Amp. Plug control comprising wall socket point
194Wiring 3 pin 16/20 amp. power plug control point
195Wiring light point with double control switches.
196RECESSED COMPUTER SUPPLY TERMINAL POINTS ( USED FOR HGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES ) Wiring Computer supply terminal points recessed in wall etc., complete with powder coated/anodized concealed metal boxes required for suitable number of modules (Modular accessories) for having 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10/16/20Amp. Switches and blanking plate etc., and covered with Frame Plate and other petty material etc. including the cost of above material, cutting and filling up of chases (with finishing the surface):- Wiring Computer terminal point having 3 Nos. 6Amp. 2/3 universal socket (shuttered), 1No. 16 Amp. switch with indicator and 1No. blanking plate (Modular accessories).
197RECESSED AIR CONDITIONER SUPPLY TERMINAL POINT (USED FOR HGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES): Wiring air conditioner supply terminal point recessed in wall etc., complete with powder coated/anodized concealed metal boxes required for suitable number of modules (Modular accessories) for having 25Amp. combined/ universal Socket (shuttered) and modular motor starter 25Amp. (2Module), covered with Frame Plate and other petty material etc. including the cost of above material, cutting and filling up of chases (with finishing the surface):- Wiring AC supply terminal point having 1No. 25Amp. universal Socket (shuttered) erected at AC height and 1No. Motor starter 25Amp. erected at switchboard height.
198RECESSED TV, TELEPHONE & NETWORKING SOCKETS OUTLET POINTS (USED FOR HGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES): Supply and erection of TV socket, Telephone socket and Networking socket points in powder coated/anodized concealed metal boxes recessed in wall required for suitable number of modules (Modular accessories) for having TV sockets, Telephone sockets RJ11 & Networking socket RJ45 (one module), covered with Frame Plate and other petty material etc., including the cost of above material, cutting and filling up of chases (with finishing the surface):- Wiring Telephone socket point RJ11 (one module)
199PVC, HDPE PIPES & PVC FLEXIBLE PIPES:Supply & erection of PVC Conduit Pipes (ISI marked) as per IS9537:Part-III & HDPE pipes (ISI marked) as per IS:4984:1995 for wiring purposes including bends, junction boxes, Steel hooks, M.S. saddle clamps and other petty materials etc., as per PWD General Specifications:- Heavy gauge PVC conduit pipe 25mm dia. (ISI marked) Flushed
200Heavy gauge PVC conduit pipe 40mm dia. (ISI marked) Flushed
201PVC, HDPE PIPES & PVC FLEXIBLE PIPES: Supply & erection of PVC Conduit Pipes (ISI marked) as per IS9537:Part-III & HDPE pipes (ISI marked) as per IS:4984:1995 for wiring purposes including bends, junction boxes, Steel hooks, M.S. saddle clamps and other petty materials etc., as per PWD General Specifications:- PVC Flexible Pipe 20mm dia.
202PVC Flexible Pipe 40mm dia.
203COPPER WIRES & CONDUIT PIPE PVC INSULATED SINGLE CORE FR COPPER CONDUCTOR CABLE:- Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:- Overall size 1 sq.mm (Un-sheathed)
204Overall size 1.5 sq.mm (Un-sheathed)
205Overall size 2.5sq.mm (Un-sheathed)
206Overall size 4sq.mm (Un-sheathed)
207Overall size 6sq.mm (Un-sheathed)
208Overall size 10sq.mm (Un-sheathed)
209Overall size 16sq.mm (Un-sheathed)
210SHEET METAL DOUBLE DOOR DISTRIBUTION BOARD FOR MCB/ RCBO/ RCCB's:- Supply and erection of sheet metal Double Door Distribution Boards IP 43- IK09 metal door (dust protected) as per IS 8623-1&3, IEC 61439-1&3 suitable for flush mounting with fully insulated copper busbars, shrouded neutral bars, earth bars, cement spill protector, colorcoded interconnecting wire set, cable ties, blanking plates and circuit identifications label and of required no. of ways for mounting miniature circuit breakers/ RCBO's/ RCCB's in the distribution board (For SP&N distribution board with provision DP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings and for TP&N horizontal distribution board with provision TPN/ FP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings) as per PWD General specifications including connections with suitable size of thimbles and bonding to existing earth etc:- TP&N Horizontal Double Door Distribution Board 4 way each
211TP&N Vertical Double Door Distribution Board 4 way each
212AC Plug and Socket TP&N with provision of One Triple Pole MCB 30/32amp.
213Supply and erection of sheet metal double door vertical distribution boards IP 43-IK09 metal door (dust protected) as per IS:8623-1&3, IEC 61439-1&3 suitable for flush mounting with fully insulated copper busbars for each phase, 2 Nos. shrouded neutral bars, 2Nos. earth bars, cement spill protector, color-coded interconnecting wire set, cable ties, blanking plates and circuit identifications label and of required no. of ways for mounting MCCB's as incomer and outgoings SP/TP miniature circuit breakers in the distribution board as per PWD General specifications including connections with suitable size of thimbles and bonding to existing earth etc.:- TP&N Double Door Vertical DB's 8 way each (With provision of FP MCCB upto 125amp.)
214MINIATURE CIRCUIT BREAKERS:-Supply and erection of Miniature Circuit Breaker MCB's for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts 50cycles AC supply with breaking capacity of 10kA, Curve-C and low watt losses as per IS/IEC 60898-1, energy limitation class-3, true contact indication, label holder facility in the existing MCB distribution board as per PWD General Specifications including connections with suitable size of thimbles/lugs:- Make:- Siemens (Beta Guard), Legrand (Lexic) , Schneider (Acti-9), L&T (Exora),Hager MCB Single Pole 6-32amp. (10kA, Curve-C)
215MCB Double Pole 6-32amp. (10kA, Curve-C)
216MCB Four Pole 40amp. (10kA, Curve-C)
217MCB Four Pole 50, 63amp. (10kA, Curve-C)
218DOUBLE WALLED CORRUGATED (DWC) HDPE PIPES:Supply and erection of Double Walled Corrugated (DWC) HDPE pipe to be laid 1mtr. below ground level including excavation placing the pipe in position and back filling with excavated soil etc. of the required size:- Double Walled Corrugated HDPE Pipe 90/76mm (Outer/ Inner dia.)
219LEDs FIXTUREs & FANs Supply and erection of LED batten 20watt LED (including LED driver) with High quality extruded aluminium with efficacy of LED fixture more than 100 lumens per watt and operating voltage between 140 to 270 volt, input AC frequency 50 Hz ± 1 % complete along with erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site.LED Fitting as per Specifications approved by Hon. Tech. Advisor to CM Punjab vide Letter no AT/2021/GL/1410-1422 Dated 06/05/2021. this the lighting fixture manufactures should have in house NABL accredited laboratory.
220Supply and erection of 3 Star rating AC Ceiling Fan 1400mm (56\\") sutiable for 230V single phase with double ball bearing, copper wound, full aluminium body 3 nos. blads,, white in clour . The mounting type is down rod mount. The product should possess a minimum air deleivery of 218 CMM . The rated speed of the product must be minimum of 350 revolutions per minute and 5 nos. of speeds . The approcimate weight of the product should be 4 Kg. and 180 grams. (without packing) or higher. The product should have a manuficturer's guarantee/warranty of minimum 2 years. The product should be complete in all aspects with fans motor, blade set , down rod , conopy sets shackle kit, twisted wires etc. including erection and testing of ceiling fans having connection with PVC sheathed two core copper conductor (FR) cable .75 sq.mm. complete in all respects as appd. and desired by the Engineer in-charge at site.
221Supply and erection of Heavy duty Exhust Fans 300mm 900RPM with aluminium louver shutter Canon of double ball bearing longer life including flexible wire & petty material etc. for connections and testing complete in all respect as approved and desired by the Engineer in-charges at site.
222Supply and erection of Heavy duty Exhust Fans 380mm 1400RPM with aluminium louver shutter Canon of double ball bearing longer life including flexible wire & petty material etc. for connections and testing complete in all respect as approved and desired by the Engineer in-charges at site.
223Supply and erection of wall fan Plastic Body 400mm sweep (16\\") including flexible wire and petty material etc. for connections and testing complete in all respect as approved and desired by the engineering in charge at site.
224Supply and erection of Recessed mounted 36watt LED panel(including LED driver) with CRCA sheet having efficacy of LED fixture more than 100 lumens per watt and operating voltage between 140 to 270 volt, input AC frequency 50 Hz ± 1 % complete along with erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site.LED Fitting as per circular issued by Hon. Tech. Advisor to CM Punjab Letter no ATBP/2021/GL/1410-1422 Dated 06/05/2021. Beside this the lighting fixture manufactures should have in house NABL accredited laboratory.
225XLPE/ PVC INSULATED UN-ARMOURED CABLES (LOOSE):-Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid loose in the existing trench or pipe as per PWD General Specifications:- Overall size 35sq.mm (3½ Core) Un-armoured (Loose)
226Supply and erection of heavy duty brass single compression gland for cable end termination duly complete with checknuts etc. including making necessary connections:- Brass Gland for Aluminium cable 2/3/3½/4 Core size 25-35sq.mm
227Supply and erection of heavy duty aluminium thimbles/lugs for cable end termination duly crimped including making necessary connections completely:- Aluminium thimble cable Core size 25 -35sq.mm
228SUPPLY AND ERECTION OF WIRING ACCESSORIES: Supply and erection of switches, sockets and other accessories (flush piano type/ modular accessories) in the existing bakelite/ modular cover frame including fixing & connections and petty material etc.:- Ceiling Rose (Flush Piano type)
229Call Bell 220/230 volts AC Ding Dong
230LAN Networking and Optical Fiber connectivity SUPPLY of 6 Core Optical Fiber Cable Unitube Double Jacket Fiber Optic Cables Steel tape armor and PE jacket provide rodent protection along with improved crush and impact protection, Water blocking tape & Water blocking yarns over FRP, Working Temperature –40°C ~+60°C Speed 10 Gbpscomplete in all respect as desired by the engineer in charge at site.
231Supply of 12 Port LIU having adaptor Plate , LC/SC type adaptor 12 No., Splice tray, 1U metal Body, Rack mountable, Cable entry slot, Support all type of fiber cables up to 12 core, Includes mounting hardware, front opening tray complete in all respect as desired by the engineer in charge at site.
232Supply of 06 Port LIU having adaptor Plate , LC/SC type adaptor 06 No., Splice tray, 1U metal Body, Rack mountable, Cable entry slot, Support all type of fiber cables up to 06 core, Includes mounting hardware, front opening tray complete in all respect as desired by the engineer in charge at site.
233Supply of SC/LC type Fiber Pigtail single mode with splicing, Working Temperature –40°C ~+85°C, Mechanical 0.9mm 10GBPS Speed, Insertion Loss-Typical:<0.2dB, Max. 0.3dB(MTRJ: Max. 0.5dB) , Return Loss- PC>_45dB, UPC>_50dB,APC>_60dB (SM). complete in all respect as desired by the engineer in charge at site.
234Supply of SC to LC type Fiber Patch cord single mode duplex 3 meter longcomplete in all respect as desired by the engineer in charge at site.
235Supply of SFP Module having speed 1GBPS LC type Fiber connector RX-TX type support Cisco Switches, single mode duplex connectivity, Metal Casing , Hot-swappable, Wave1310nm, Single Mode Fiber, Transmit and Receive Wavelength (nm) -1260 to 1355 length, Power consumption 1 Watt, complete in all respect as desired by the engineer in charge at site.
236Supply of 24 Port SFP Managed L2 10/100/1000 Mbps Smart Data switch having IEEE 802.3 10BASE-T Ethernet, IEEE 802.3u 100BASE-TX Fast Ethernet, IEEE 802.3ab 1000BASE-T Gigabit Ethernet, IEEE 802.3z Gigabit Ethernet, IEEE 802.3x Flow Control, 802.1p priority, Energy Efficient Ethernet, Switching capacity 56 Gbps, HOL blocking prevention, 802.1p priority based, hardware queues, priority queuing and Weighted Round-Robin (WRR) Jumbo frame having 2 No. Combo SFF/Copper Up-Link
237Supply of 24U Floor mount 19’’ Rack with glass door, lock & key facility minmum 400mm depth with CPD, Cable Manager & Fan. Complete in all respect as desired by the Engineer in charge of work at site.
238Supply of 9U Wall mount 19’’ Rack with glass door, lock & key facility 450mm-550mm depth. with CPD, Cable Manager & Fan. Make:
239Supply of CAT 6 ONE Meter long Patch Cord Having RJ-45 Male Connectors on both ends DCC up-to 10/100/1000 mbps.
240Supply of CAT 6 TWO Meter long Patch Cord Having RJ-45 Male Connectors on both ends DCC up-to 10/100/1000 mbps.
241Supply of CAT 6, 24 Port Fully loaded Patch Panel, Rack Mountable for cable termination.
242Supply of 24 Port Networking with Up link Switch with Having 10/100/100 MBPS Speed, auto port configuration, upto 2000 MBPS speed in duplex mode, auto negotiation, LED Indicator for link/act with rack mounting kit and AC Power cord compatible with existing LAN network and switches.
243Supply of 600VA LIT sine wave UPS/ Power Plant with SMF battery having 30 Minutes backup time.
244Supply of CAT6 UTP Networking Cable having speed of 10/100/1000 mbps Dual PVC Jacket LDPE and PVC Sheathed for greater protection Nominal Conductor Diameter- (23 AWG), Conductor- Solid Bare Electrolytic Grade Copper Thickness of Inner Jacket- 0.45 mm ± 0.05 mm, Thickness of Outer Jacket - 0.55 mm ± 0.05 mm CAT6 UTP Cable Having speed upto 1Gbps.
245EPABX Service Supply Digital BSNL Trunk card for BSNL DIGITAL LINES upto 30 BSNL Digital Lines with single Fiber in existing EPABX system with 01 no RJ-45 Connector and 01 year warranty. Make Matrix
246Installation, Programming and customization of system software and re-programming of Epabx system as per user’s requirement.
247Supply of 10 Pair DB with Original Krone Module lock& key facility. Make Krone
248Supply of Beetel Basic Phone with CLIP and display . Make Beetel
249Supply of Featured Wired Telephone with Large Backlit Display, Redial, CLIP, 2 Way Speaker,& Mute Compatible with EPABX System Without Addition Programming. Make: Beetel
250Supply of 02 Pair 0.5mm PVC Dual sheathed Telephone Cable manufactured as per ITD Specification with Up to amendments. Make: Finolex / Shalimar
251Supply of 05 Pair 0.5mm PVC Dual sheathed Telephone Cable manufactured as per ITD Specification with Up to amendments. Make: Finolex / Shalimar
252Fire Detection and Alarm Services Supply and erection of 04 Zone Conventional Fire Alarm Sub Panel Make Agni Suraksha with following feature:-= Operates on 230 V AC, 50 Hz AC supply= Battery backup with built in charger= Battery backup with built in charger = Fire / fault status in unambiguous colour LED indications. = 16 x 2 line dot matrix LCD display = Zone wise fire, open, short LED indications.= External s/w to test each zone fire, open, short status manually.= External s/w for reset, Silence, Lamp test.= Zone isolation facility with loop voltage cut off.= Mains on, System On, Charger on, visual indications.= Battery Low& Common fire indications = Attachable with all types of fire detectors.= Connectivity with Main Fire Panel
253Supply and erection of Photoelectric Smoke Detector, low current draw, wide operating voltage, LED detector status indicator, Programmable sensitivity, automatic drift compensation Tested and approved to EN54-7:2000 complete in all respect as desired by the engineer in charge at site.Make- Honeywell System Sensor
254Replacement of electrical hooter operational with DC 24 Volts, sounder output 80 db @ 1 meter and 2 core wiring complete in all respect as desired by the engineer in charge at site.Make- National/ Agni Suraksha
255Replacement of Glass break manual call point complete in all respect as desired by the engineer in charge at site. Make- /Honeywell System Sensor
256Supply & erection of C.F.L./L.E.D. type Fire Exit Glow sign for the evacuation at the time of emergency having 220VAC/ 6VDC power supply complete in all respect as desired by the engineer in charge at site. Make- National/ Agni Suraksha
257PVC INSULATED SINGLE CORE FR COPPER CONDUCTOR CABLE:- Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:- Overall size 1 sq.mm (Un-sheathed) 2 core
258PVC, HDPE PIPES & PVC FLEXIBLE PIPES:Supply & erection of PVC Conduit Pipes (ISI marked) as per IS9537:Part-III & HDPE pipes (ISI marked) as per IS:4984:1995 for wiring purposes including bends, junction boxes, Steel hooks, M.S. saddle clamps and other petty materials etc., as per PWD General Specifications:- Heavy gauge PVC conduit pipe 25mm dia. (ISI marked) Flushed
259Providing one extra landing in existing 2 Nos.13 Passengers Lifts (from 3rd floor to 4th floor) Design, manufacture, supply, installation, testing and commissioning of one extra landing in existing13 Passengers Lift (from 3rd floor to 4th floor) with following changes:-1.Travelling within 4mtr (Guiderail,Bracket etc.),2.Extra wiring and travelling cables.3.Car operating panel.4.Landing operating panel.5.Extra door with door frame (40% area should be visible by glass) ..Make:-Schindler Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58505422
AUTHORITY Government Departments
TENDER VALUE 2.45 Crore
LAST DATE 03-12-2026
Authority
Authority Name Public Works Department
Work Description Tender for Construction Of New Court Room At 3Rd Floor Of New Judicial Court Complex At Nawanshahr Distt. Shaheed Bhagat Singh Nagar
Basic Detail
Tender No Tender Notice No 12 Dt 12.11.2026
Bidding Type Tender
Location
City Shahid Bhagat Singh Nagar
State Punjab
Key Dates
Publish Date 13 Nov 2026
Submission Date 03 Dec 2026
Open Date 04 Dec 2026
Finance
Tender Value 2.45 Crore
Tender Fee 20000
EMD 4.91 Lakhs
Exemption Not Available
Document List
BOQ_366273.xls
d46976f1-7ed8-4793-8308-577168ed08dd.html
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 13, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 03, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 15 days
Dec 04, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 16 days

Tender Documents

Download All (ZIP) ↓
xls

BOQ_366273.xls

html

d46976f1-7ed8-4793-8308-577168ed08dd.html

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender