Tender For Providing Electrical Services In Session House And Houses For Judicial Officers At Fazilka (Providing Campus Lighting)
Tender Value
29.24 Lakhs
Estimated cost
Bid Submission
23 Nov 2026
7 days left
EMD
58500
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Fazilka → Punjab
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Providing Electrical Services In Session House And Houses For Judicial Officers At Fazilka (Providing Campus Lighting)
BOQ
| Sl. No. | Item Description |
| 1 | GALVANIZED STEEL OCTAGONAL POLES FOR WIND VELOCITY OF 169 Km/ HOUR: |
| 2 | Supply and erection of Galvanized Steel Octagonal Pole (Sheet thickness 3mm) designed to withstand wind speed 169km/ hour of suitable length (Raw material confiming to IS-5986 (FE-510), BSEN-10025S-355J or ASTM-572A (GR-50)) and thickness of galvanization (70mm thick) conforming to IS:2629/ IS:2633/ IS:4759, BSEN-ISO-1461- 1991 OR ASTM-A123/A123M-02. The poleshall be in single piece hot dip galvanized and shall be tapered towards the top. The bottom section shall have openable slot with exterior surface door & shall have suitable locking arrangement for housing three phase 4wire cable connection, bakelite sheet, MCB, loop in and out arrangement for incoming/ outgoing cables. There shall be suitable arrangement for earthing. Rigid Base plate of suitable size and thickness shall be welded inside and outside at the bottom of pole with provision for fixing 4 foundation bolts. The octagonal pole shall be bolted on a pre- cast foundation with a set of four foundation bolts for greater rigidity. The foundation shall be erected over cement concrete M20 with steel of given size as per design of original pole manufacturer to fixed up to a required planting depth below ground level as required:- |
| 3 | Galvanized Octagonal Pole Overall Length 6 metre (Sheet thickness 3mm), Top dia.(A/F) 70mm and bottom dia. (A/F) 130mm, Foundation size below G/L 550mm x 550mm x 1200mm, 4Nos. Foundation Bolts size 20mm dia., Length≥600mm with Base Plate Dimensions 220mm x 220mm x 12mm Thick |
| 4 | GALVANIZED OCTAGONAL POLE BRACKETS: |
| 5 | SINGLE/ DOUBLE ARM BRACKETS: |
| 6 | Supply and erection of bracket for galvanized octagonal pole, the bracket should be fixed on the top of the pole having top outer dia. 70mm to 90mm (A/F) complete in all respect as approved by the Engineer-in-charge at site:- |
| 7 | Single arm bracket 1 metre long for galvanized octagonal pole |
| 8 | Double arm bracket 1 metre long for galvanized octagonal pole |
| 9 | GI PIPE POLES & BRACKETS: |
| 10 | GI PIPE POLES: |
| 11 | Supply and erection of G.I. pipe ‘A’ quality of suitable length and dia. confirming to IS:1239 (Part-I) 1979, including fixing up to a given depth below G/L, the hole of excavation about 30cm dia. and given depth to be filled in up to 15cm below G/L with 1:2:4 cement concrete including painting of pole with two coats of approved aluminium paint as required:- |
| 12 | G.I. Pipe Pole 4 metre Long, Dia. 65mm, Planting Depth 80cm with Pit Depth 95cm. |
| 13 | CEMENT CONCRETE MUFFS: |
| 14 | Making of cement concrete muff of overall size 450mmdia., suitable length (15cm below ground level) with 1:2:4 cement concrete mixture. The muff is to be made around the steel tubular pole/ GI pipe pole. The outer surface of the muff shall be finished with 1:2 cement plaster with two coats of white snowcem complete in all respect as approved and desired by the Engineer in Charge at site:- |
| 15 | Cement Concrete Muff of Overall Size 450mm dia., 60cm long |
| 16 | XLPE INSULATED UN-ARMOURED CABLES (LOOSE): |
| 17 | Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid loose in the existing trench or pipe as per PWD General Specifications:- |
| 18 | Overall size 10sq.mm (2Core) Un-armoured (Loose) |
| 19 | Overall size 25sq.mm (3½ Core) Un- armoured (Loose) |
| 20 | PVC INSULATED FR COPPER CONDUCTOR CABLES: |
| 21 | Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:- |
| 22 | Overall size 1.5sq.mm (Un-sheathed) |
| 23 | DOUBLE WALLED CORRUGATED (DWC) HDPE PIPES: |
| 24 | Supply and erection of Double Walled Corrugated (DWC) HDPE pipe to be laid 1mtr. below ground level including excavation placing the pipe in position and back filling with excavated soil etc. of the required size:- |
| 25 | Double Walled Corrugated HDPE Pipe 50/38mm (Outer/ Inner dia.) |
| 26 | MINIATURE CIRCUIT BREAKERS/ RCBO's/ RCCB's: |
| 27 | MINIATURE CIRCUIT BREAKERS: |
| 28 | Supply and erection of Miniature Circuit Breaker MCB's for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts 50cycles AC supply with breaking capacity of 10kA, Curve-C and low watt losses as per IS/IEC 60898-1, energy limitation class-3, true contact indication, label holder facility in the existing MCB distribution board as per PWD General Specifications includingconnections with suitable size of thimbles/lugs:- |
| 29 | MCB Single Pole 6-32amp. (10kA, Curve-C) |
| 30 | MCB Double Pole 6-32amp. (10kA, Curve- C) |
| 31 | MCB Four Pole 50, 63amp. (10kA, Curve-C) |
| 32 | SHEET METAL DOUBLE DOOR DISTRIBUTION BOARD FOR MCB's/ RCBO's/ RCCB's: |
| 33 | Supply and erection of sheet metal Double Door Distribution Boards IP 43- IK09 metal door (dust protected) as per IS 8623-1&3, IEC 61439-1&3 suitable for flush mounting with fully insulated copper busbars, shrouded neutral bars, earth bars, cement spill protector, color- coded interconnecting wire set, cable ties, blanking plates and circuit identifications label and of required no. of ways for mounting miniature circuit breakers/ RCBO's/ RCCB's in the distribution board (For SP&N distribution board with provision DP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings and for TP&N horizontal distribution board with provision TPN/ FP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings) as per PWD General specifications including connectionswith suitable size of thimbles and bonding to existing earth etc:- |
| 34 | TP&N Horizontal Double Door Distribution Board 4 way each |
| 35 | SHEET METAL CUBICAL PEDESTAL, TOWER STRUCTURES, HT & LT LINE ITEMS, MS CHANNELS, BRASS GLANDS, ALUMINIUM & COPPER THIMBLES: |
| 36 | CUBICAL PEDESTAL: |
| 37 | Supply and erection of Sheet metal cubical pedestal made from 50mmx50mmx6mm thick MS angle iron frame with 5 sides welded & covered with MS sheet 2mm thick & front side hinged with 4\\" hinges & locking system with single/ double door openable placed on MS strip of size 12.5mm x 2.5mm thick welded with MS sheet, 4Nos. legs of 50mmx50mmx6mm thick MS angle iron each of 600mm long with MS sheet 100mmx100mmx6mm thick at the bottom end of the legs. Front door welded x-sectionally with MS flat 25mmx5mm. The front side with MS sheet each 75mm wide & a bend of 75mm width outwards & inwards on all sides with tappered top 200mm high and pedestal with 4 Nos. supporting members each of MS flat 50mmx6mm thick according to cubical size duly welded & complete pedestal to be painted with 1 coat of red oxide & 2 coats of paint & bonding to the existing earth. The Pedestal platform should be filled with 1:2:4 cement concrete mixture and erected 150mm high from the top of the cement concrete platform. The job is to be completed as approved by Engineer-in-charge:- |
| 38 | Cubical Size 900mm high, 600mm wide and 350mm deep with platform dimensions 700mm x 450mm x 450mm |
| 39 | G.I. EARTHING: |
| 40 | Earthing with G.I. wire/ rope in G.I. pipe partly recessed and partly on surface complete with 150cm long 50mm dia. G.I. earth pipe (Cutting threads and 36 Nos. holes, 1cm dia. to make a mesh around the GI Pipe) and with G.I. reducing socket including erection of the same, 10.50 metre (34.44 feet) below ground level with 20Kg. charcoal & salt mixture etc., up to 14 metre in length (including boring & refilling). |
| 41 | Earthing with 7/14 S.W.G. (7/2.18mm dia.)G.I. rope in 20mm dia G.I. pipe with G.I. reducing socket 50mm x 20mm (upto 14Metre in length) |
| 42 | Earthing earth rod 20 mm dia for providing earth connections upto line earth with G.I. Wire 8 S.W.G. (4mm dia.). The rod shall be tapered at one end and flatted on other end. The hole size 10mm dia shall be drilled on the flatened side for facilitating connection with G.I. wire and thimble etc. The rod shall be erected in ground upto complete length vertically:- |
| 43 | GI Earth rod 20 mm dia., 3 mtr. Long |
| 44 | Supply and erection of LED Street Light 72 watt with pressure die cast aluminium housing with control gear ( with IP 66 protection), toughened glass fitting and efficacy of LED fixture minimum 120 lumens per watt supply v/g 140-210v AC supply, 50Hz+3%, THD<10%, CRI minimum 70, High power Led with wattage 1-5watt with mandatory secondary leases, toughened glass fitting H Kv SPD within driver & 10KV external SID, Minimum 1K07, 5 year warranty icnluding their drivers. complete in all respects as approved and desired by the Engineer in-charge at site . LED Fitting as per Specifications approved by Hon. Tech. Advisor to CM Punjab vide Letter no AT/2021/GL/1410-1422 Dated 06/05/2021 (Besides this, Lighting Fixtures Manufactures should have inhose NABL accredited lab. |
| 45 | Supply and erection of LED Post top opal diffuser 35/40 watt with IP 65 protection including LED driver having efficacy of LED fixture minimum 120 lumens per watt and operating voltage between 140 to 270 volt, input AC frequency 50 Hz ± 3% THD<10% CRI min 10, High Power LED With 1-5 watt complete along with erection of the same with connections, testing etc. with 5 years warranty complete in all respects as approved and desired by the Engineer-in-charge at site.LED Fitting as per Specifications approved by Advisor to CM Punjab vide Letter no AT/2021/GL/1410-1422 Dated 06/05/2021.Besides this, the lighting fixtures, should have in house NABL Accredited Lab. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 12, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 23, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 7 daysNov 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender