Tender For Addition/ Alteration/ Improvement To Building No P-159 At Afs Sulur
Tender Value
43.30 Lakhs
Estimated cost
Bid Submission
03 Dec 2026
18 days left
EMD
86600
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Tiruppur → Tamil Nadu
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Addition/ Alteration/ Improvement To Building No P-159 At Afs Sulur
BOQ
| Sl. No. | Item Description |
| 1 | Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out hard/dense soil complete all as specified and as directed. |
| 2 | Excavation in trenches not exceeding 1.5 mtr depth and n exc 1.5 mtr wide and getting out in hard/dense soil complete all as specified and as directed. |
| 3 | Returning, filling in, including spreading, leveling, watering and well ramming in layer not exceeding 25cms thick complete all as specified and as directed |
| 4 | Removing excavated soil to a distance exceeding 1.5Km not exc 5.0Km and depositing where directed at a level, not exceeding 1.5 metre above the starting point complete all as specified and as directed |
| 5 | Material and labour for plain cement concrete type D2, 1:4:8 using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and as directed. |
| 6 | Material and labour for precast PCC 1:3:6 type C1 using 20 mm graded aggregate solid block masonry exceeding 10cm width, built in cement mortar 1:6 complete all as specified and as directed. |
| 7 | Material and labour for rendering 15 mm thick in cement mortar 1:6, on fair faces of brick work/concrete surfaces finished even and fair complete all as specified and as directed. |
| 8 | Material and labour for preparation of newly plastered wall surfaces and applying two coats of cement based paint over one coat of alkali resistant primer complete all as specified and as directed. |
| 9 | Material and labour for 10mm thick rendering in cement mortar 1:4, on fair faces of brick work/concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed. |
| 10 | Material and labour for preparation of newly plastered wall surfaces, applying 1mm thick plaster of paris and applying two coats of oil bound distemper of required shade over a coat of primer complete all as specified and as directed by Engineer-in-Charge. |
| 11 | Material and labour for rendering 5mm thick on ceiling surfaces in CM 1:3 even and smooth without using extra cement complete all as specified and as directed. |
| 12 | Material & labour for preparing newly plastered surfaces and applying three coats of white wash on ceiling complete all as specified and as directed. |
| 13 | Material and labour for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 14 | Material and labour for TMT bars, 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending, spirally hooping for columns hooking ends and binding with mild steel wire annealed not less than 0.9mm dia or securing with clips complete all as specified and as directed. |
| 15 | Use and waste of formwork to sides of concrete foundation, etc, rough finished, flat surfaces of concrete complete all as specified and as directed. |
| 16 | Material and labour for RCC M-25 design mix using 20 mm graded stone aggregate as in foundations including raft, footings, plinth beam and mass concrete and similar work complete all as specified and as directed. |
| 17 | Use and waste of formwork to sides of column, pillars etc fair finished flat surfaces of concrete complete all as specified and as directed. |
| 18 | Material and labour for RCC M-25 design mix using 20 mm graded stone aggregate as in columns, pillars etc and similar work complete all as specified and as directed |
| 19 | Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splays between floors and beams, etc. rough finished complete all as specified and as directed. |
| 20 | Material and labour for RCC M-25 design mix using 20 mm graded stone aggregate as in beams, cantilevers etc and similar work complete all as specified and as directed. |
| 21 | Use and waste of formwork to soffit of suspended slabs such as roof slab, landing etc not exceeding 200 mm thick for rough finished, flat surface complete all as specified and as directed. |
| 22 | Material and labour for RCC M-25 design mix using 20mm graded stone aggregate for slabs supported on walls, beams and column in floors, roofs, landings, balconies, canopies, deck slab and in shelves and the like complete all as specified and as directed. |
| 23 | Material and labour for hard core (broken boulders and stones) of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick broken stone or boulders, water and rammed to a true surface complete all as specified and as directed. |
| 24 | Material and labour 100mm thick plain cement concrete 1:4:8 type D2 using 40 mm graded stone aggregate as in floor, path/ hard standing complete all as specified and as directed. |
| 25 | Material and labour for 40mm thick plain cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in floors and pavings etc finished even and smooth without using extra cement complete all as specified and as directed. |
| 26 | Material and labour for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed. |
| 27 | Material and labour for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface complete all as specified and as directed.Note: Area of the sub structure in contact with backfill to be measured |
| 28 | Material and labour for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and as directed. |
| 29 | Material and labour for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed. |
| 30 | Material and labour for light shade vitrified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and as directed. . |
| 31 | Material and labour for light shade vitrified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in vertical surfaces such as skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and as directed. . |
| 32 | Material and labour for 75mm thick plain cement concrete 1:3:6 type C2 using 40mm graded stone aggregate as in plinth protection/ pavement complete all as specified and as directed. |
| 33 | Supply and fixing factory made uPVC white colour three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead /double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multi chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and as directed by Engineer-in-Charge.Note: a) Glass and wire mesh shall be deemed to be measured and paid separately under relevant items.b) For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 34 | Supply and fix 4mm thick, plain sheet glass, ordinary quality and glazing with oil putty /beeding in squares exceeding 0.5 sqm each pane for fixing to aluminium/ wooden/ UPVC joinery work complete all as specified and as directed. |
| 35 | Supply and fix stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed with stainless steel wire staples complete all as specified and as directed. |
| 36 | Supply and fix framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed. |
| 37 | Material and labour for preparation of new steel and iron surfaces of any description exceeding 10cm in width or girth and apply two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed. |
| 38 | Material and labour for polythene film, 150 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg per sq. m complete all as specified and as directed. |
| 39 | Material and labour for Moorum/red bajri filling in floors or pavings, laid in layer, spread and levelled in layers not exceeding 150mm thick, watered and rolled/rammed to a true surface complete all as specified and as directed. |
| 40 | Material and labour for plain cement concrete 1:2:4, type B0, 40mm thick damp proof course to horizontal or vertical surfaces including necessary formwork complete all as specified and as directed. |
| 41 | Supply and fix powder coated aluminium frame for windows, doors & ventilators with one or more rebates including joining cleats for fixing etc. complete all as specified and as directed.Note: Thickness of powder coating shall be minimum 50 micron |
| 42 | Supply and fix powder coated aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, hydraulic door closure and floor spring, handles 2 Nos in each doors, hinges, anodised aluminium snap beading screws etc complete all as specified and as directed. Note:-Glazing/gauzing and particle board work shall be measured and paid separately. Thickness of powder coating shall be minimum 50 micron |
| 43 | Supply and fix 12mm thick pre-laminated particle board, interior grade, prelaminated both sides with decorative choice laminations fixed with screws to aluminium frame work complete all as specified and as directed. |
| 44 | Supply and fix 5.5mm thick, plain sheet glass ordinary quality and glazing with oil putty exceeding 0.5Sqm in each pane complete all as specified and as directed. |
| 45 | Supply and fix brass mortice lock, vertical type, size 100 mm, 4 levers complete all as specified and as directed. |
| 46 | Supply and fix aluminium extruded body door closer hydraulically regulated, designation No. 3 universal type with aluminium (die cast) body, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed. |
| 47 | Material and labour for double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel covert governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and as directed. |
| 48 | Material and labour for 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated in the solid, rounded or chamfered put together with glue, pinned at joints complete all as specified and as directed. |
| 49 | Supply and fix 40mm thick flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides and covered with decorative face veneer on both faces with lipping/frame to match complete all as specified and as directed. |
| 50 | Supply and fix 100mm butt hinges, extruded brass, with mild steel hinge pin, bright polished and fixed, type B-11 and fixed complete all as specified and as directed. |
| 51 | Supply and fix 150mm long extruded brass handles, fabricated type, polished complete all as specified and as directed. |
| 52 | Supply and fix 300mm long brass sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and as directed. |
| 53 | Supply and fix 150mm long brass, barrel tower bolts with barrel of extruded section and fixed complete all as specified and as directed. |
| 54 | Supply and fix floor door stopper of brass body and tongue anodized with hard drawn steel spring fixed in floor overall 140mm complete all as specified and as directed. |
| 55 | Material and labour for preparation of new or previously untreated wooden surfaces of any description exceeding 10cm width or grith not otherwise specified and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed. |
| 56 | Material and labour for granite 20mm thick of any type work, table rubbed and polished, for steps, jambs, pillars, window cills, cooking platforms and like in CM 1:4, pointing with white cement 1:2 using marble dust with admixture of pigment to match with shade of granite including 15mm thick screed bed in cement mortar 1:4 complete all as specified and as directed. |
| 57 | Supply and fix factory made solid PVC moulded door shutter, 30mm thick, style, consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, supplying and fixing in the frame at site complete all as specified and as directed. |
| 58 | Supply and fix solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed. |
| 59 | Material and labour for glazed ceramic coloured tiles of size 450mm x 350mm x 7mm, set and jointed in neat cement slurry and pointed in white or coloured cement to match with tiles on vertical surfaces complete including 10mm thick back coat in CM 1:3 complete all as specified and as directed. |
| 60 | Material and labour for non-skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed 15mm thick in cement mortar 1:4 complete all as specified and as directed. |
| 61 | Supply and fix 25mm dia CPVC pipes SDR-11 & plain CPVC SDR 11 fittings, high pressure, fixed on wall/ceilings or laying in floors with all necessary fittings, solvents complete all as specified and as directed. |
| 62 | Supply and fix 20mm dia CPVC pipes SDR-11 & plain CPVC SDR 11 fittings, high pressure, fixed on wall/ceilings or laying in floors with all necessary fittings, solvents complete all as specified and as directed. |
| 63 | Supply and fix 20mm dia CPVC Gate valves (brass insert) as per requirement of the site fixed to walls, ceilings or in floors etc. complete all as specified and as directed. |
| 64 | Supply and fix 25mm dia CPVC Gate valves (brass insert) as per requirement of the site fixed to walls, ceilings or in floors etc. complete all as specified and as directed. |
| 65 | Supply and fix 24\\" long towel rail, brass, chromium plated, fixed complete all as specified and as directedMake: Cat part No. CAN-1111NM of Jaquar series or equivalent as per list of manufactures. |
| 66 | Supply and fix angular stop cock, high pressure screwed both ends iron pipe or for unioins 15mm dia complete all as specified and as directed.Make: Cat Part No CQT 23059 of Jaquar or equivalent as per list of manufactures. |
| 67 | Supply and fix 600mm x 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed by Engineer-in-Charge |
| 68 | Supply and fix 15mm dia bib cock with wall flange screwed down screwed for iron pipe complete all as specified and as directed.Make: Cat Part No CQT 23047 of Jaquar or equivalent as per list of manufactures. |
| 69 | Supply and fix 15mm dia pillar cock chromium plated with capstan head screwed down high pressure, screwed for iron pipe complete all as specified and as directed.Make: Cat Part No PRS 031 of Jaquar or equivalent as per list of manufactures. |
| 70 | Supply and fix PVC Dual flush ceramic colour, low level, 10 litres capacity, star white with inlet float ball valve, PVC flush pipe and handle, making proper fixing and hanging arrangements complete all as specified and as directed.Make: Cat Part No 21029 of Hindware or equivalent as per list of manufactures. |
| 71 | Supply and fix vitreous china wash hand basin, white, size 550 x 400mm, under counter type of size 560x470x190mm excluding taps, waste chain and plug and porcelain stopper but including brackets, cutting and pinning in ends of brackets or erecting stand complete all as specified and as directed.Make: Cat Part No 0493 Niagara of Parryware or equivalent as per list of manufactures. |
| 72 | Supply & fix 32mm dia waste fittings, brass, chromium plated for basins with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixing complete all as specified and as directed by Engineer-in-Charge |
| 73 | Supply and fix health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed by Engineer-in-Charge |
| 74 | Supply and fix Soap dish, chromium plated complete all as specified and as directed. Make: Cat part No ACN-1131N of Jaquar or equivalent as per list of manufactures. |
| 75 | Supply and fix vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white, closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. excluding flushing cistern & flush pipe complete all as specified and as directed. |
| 76 | Supply and fix plastic water closet seat for EWC with flat bottom and cover and mild steel chromium plated or alluminised hinging device fixing complete all as specified and as directed. |
| 77 | Material and labour for PVC(SWR) pipe 110mm dia single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and as directed by Engr-in-Charge. |
| 78 | Supply and fix PVC SWR bends 110mm dia of any radius including complete all as specified and directed. |
| 79 | Material and labour for PVC(SWR) pipe 75mm dia single socketed, in any length with rubber ring joints, fixed to wall complete all as specified and as directed by Engr-in-Charge. |
| 80 | Supply and fix PVC SWR bends 75mm dia of any radius including complete all as specified and directed. |
| 81 | Supply and fix PVC (SWR) floor trap up to 75mm outlet, plain with grating including jointing with solvent cement complete all as specified and as directed. |
| 82 | Supply and fix PVC (SWR) 75mm bore junction vent cowl complete all as specified and as directed. |
| 83 | Supply and fix PVC(SWR) gully trap 125/110mm dia of outlet, set and jointed with solvent cement complete all as specified and as directed. |
| 84 | Supply and fix doom grating 125mm dia with waste hole of PTMT (minimum weight 40gms) complete all as specified and as directed by Engneer-in-Charge. |
| 85 | Supply and fix PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed. |
| 86 | Supply and fix 15mm bore CP sink cock with swinging casted round shape spout screwed down screwed for iron pipe of complete all as specified and as directed by Engineer-in-Charge.Make: Cat part No QT F2006251 HT F3001251 of Cera or equivalent as given in list of makes |
| 87 | Material and labour for water proofing treatment on roofs as per details given below after complete removal of existing water proofing treatment and expose of top surface of RCC slab of any thickness, any type by stripping out old tar felt over roofs, parapets, chimney stacks etc laid horizontally or vertically including taking out layer of cement plaster etc and cleaning the surface with water and using wire brush including removing debris to outside the MOD land complete all as specified and as directed :- |
| 88 | Notes:(a) Surface should be free from any loose paint, dust or grease. Remove all existing bitumen coatings completely by using intense wire brushing, high speed water jet & vacuum cleaner for thorough cleaning of the surface to avoid ‘Peeling off’ problems.(b) All cracks at corner joints, channels and parapets should be properly treated. For filling cracks upto 3mm crack seal material of M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical to be used. Bigger cracks, damaged portions & hollow areas must be repaired with polymer modified cement mortar. (c) Apply a coat of self priming smart care damp proof ultra (Code 5698) of M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical with 33% dilution with water using brush/roller on newly plastered surface after curing as per IS-456 and allow to dry for 4 to 6 hours (dilution & forced coverage requirement strictly as per manufacturer’s instructions).(d) After the primed surface has dried, apply first coat of water proofing smart care damp proof ultra (Code 5698) of M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical using brush/roller on the same primed surface & allow to dry for 4 to 6 hours.(e) Prepare for apply 2nd coat of water proofing smart care damp proof ultra (Code 5698) of M/s Asian paints or equivalent in M/s Dr Fixit or M/s Pidilite or M/s Sika chemical using brush/roller on the same surface. The temp to be maintained 25 to 35° C through out the all above application work.(f) In case of severe dampness an additional coat of damp proof materials to be applied. |
| 89 | Supply and fix 1000 Ltrs rotational moulded polythylene water storage tank, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I, ISI marked, alongwith 3 Nos GI check nuts and tank nipple of 25mm bore for inlet and outlet, fixed in position complete all as specified and as directed. |
| 90 | Material and labour for making connection for PP-R distriburion branch with PP-R main of size 16 to 40 mm outer dia by providing and fixing tee including cutting and making fusion joint etc complete all as specified and as directed. |
| 91 | Supply and fix Ball brass valves, of size 20mm bore, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed. |
| 92 | Supply and fix 20mm outer dia of pipes 3-layer PP-R (Polypropylene random copolymer) pipes concealed pipes SDR 7.4, PN-16 @ 20˚C, UV stablised and anti-microbial fusion welded having thermal stability for hot & cold water supply alongwith all PP-R plain and brass threaded polypropylene random fittings, complete to walls, ceilings or in floors etc. complete all as specified and as directed. |
| 93 | Supply and fix 20mm outer dia of pipes PP-R gate valves (brass insert) as per requirement of site complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 94 | Supply and fix 20mm outer dia of pipes PP-R gate valves (brass insert) as per requirement of site complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 12, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysDec 05, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender