Tender For special Repair To Sewage Line And Connected Works And special Repair Of Broken And Falling Tiles On Somnath Sharma Gate Wall Under Ge (North) Bathinda At Bathinda Mil Stn
Tender Value
38.80 Lakhs
Estimated cost
Bid Submission
26 Nov 2026
4 days left
EMD
77600
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bathinda → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Sewage Line And Connected Works And special Repair Of Broken And Falling Tiles On Somnath Sharma Gate Wall Under Ge (North) Bathinda At Bathinda Mil Stn
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling existing floor, hearth or wall tiling, including removal of cement mortar bedding but excluding backing/plaster, carefully taking up and removing the tiles without causing unnecessary damage to the underlying surface, separating and stacking serviceable tiles at a location indicated by the Engineer-in-Charge, removing and disposing of unserviceable tiles, dismantled mortar and rubbish off the premises, including all necessary labour, tools and plants, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 2 | Material and labour for providing and fixing premium quality glazed ceramic coloured wall tiles, of approved make, shade and pattern, including combination of light, dark and highlighter tiles as approved by GE, each tile having an area exceeding 0.11 Sqm but not exceeding 0.18 Sqm, thickness 7–8 mm, water absorption between 10% and 20%, with straight edges, stain-free and glossy finish, as in vertical surfaces such as skirting, dado and similar locations, including preparation of the background surface and laying and fixing the tiles over and including 10 mm thick backing in cement mortar (1:4), using suitable tile adhesive/neat cement slurry as required, maintaining proper line, level, plumb, alignment and uniform joint width, including cutting, shaping and fitting tiles at corners, edges, junctions, openings and other locations to suit site requirements, filling all joints with approved colour-matching epoxy grout, cleaning the finished surface and all necessary materials, labour, tools, equipment and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 3 | Material and labour for providing and laying premium quality non-skid, jointless, coloured ceramic floor tiles, square or rectangular in shape, of approved make, shade, design and pattern, each tile having an area exceeding 0.11 Sqm but not exceeding 0.18 Sqm, and thickness 7–8 mm, as in floors, including preparation of the base surface and laying the tiles over and including 15 mm thick cement mortar screed (1:6), using suitable tile adhesive/neat cement slurry as required, maintaining proper line, level, slope, alignment and uniform joint width, including cutting, shaping and fitting tiles at edges, corners, junctions, doorways and other locations to suit site requirements, filling all joints with approved colour-matching epoxy grout, cleaning and finishing the tiled surface to achieve a uniform, durable and non-skid finish, including all materials, labour, tools, equipment and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 4 | Supply and fixing of 16–18 mm thick Dholpur stone cladding, gang-saw cut, with machine-cut edges and uniform colour and texture, each stone slab having an area not exceeding 0.25 Sqm, on vertical surfaces as specified, including dressing, cutting and shaping to the required dimensions, making V-grooves at the top and bottom edges of each stone slab, drilling holes for fixing holdfasts/clamps, providing and fixing approved suitable stainless steel clamps/holdfasts, and securing the stone slabs firmly in position. The work shall include and be executed over 10 mm thick backing plaster in cement mortar (1:4), filling joints with approved colour-matching epoxy grout, applying suitable silicone sealant/treatment at required joints and junctions, rubbing, grinding and polishing the exposed stone surface to achieve a uniform smooth finish, including all necessary cutting, fitting, alignment, line, level, plumbing, materials, labour, tools, tackles, scaffolding and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 5 | Material and labour for providing and applying 10 mm thick bedding layer of approved Type-I cement-based tile adhesive, conforming to IS 15477:2004, suitable for thick-bed fixing of wall tiles, floor tiles and Dholpur stone cladding, including preparation and cleaning of the base surface, mixing the adhesive with water in the proportions recommended by the manufacturer, applying uniformly to the required thickness, spreading and levelling the adhesive bed, fixing and pressing the tiles/stone firmly into position to ensure proper bonding and full contact without voids, maintaining proper line, level, plumb, alignment and required joint width, including all necessary materials, labour, tools, equipment and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 6 | Supply and fixing in repairs of one-piece vitreous china, premium/first-quality wash-down type European Water Closet (EWC), white/ivory/off-white colour, with matching seat cover and built-in closed-pattern flushing cistern, including all necessary accessories and fittings such as suitable S-trap or P-trap, as required at site, rag bolts, rubber/gel gasket, fixing screws, washers, sealing materials and other requisite connection accessories, including dismantling/removal of the existing defective WC, preparation of the fixing surface, positioning, alignment, fixing securely, making connections to the existing soil pipe and water supply, testing for proper flushing, leakage and satisfactory operation, and making good the disturbed surfaces, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 7 | Supply and fixing in repairs of vitreous china wash basin, white colour, flat-back type, size 550 mm × 400 mm, of approved make and first quality, including providing and fixing cast iron brackets securely embedded into the wall up to 110 mm depth with and including cement concrete M15 (nominal mix) using 20 mm nominal size graded crushed stone aggregate, or alternatively fixing the basin to the wall with approved rawl plugs and screws, as suitable to the site conditions. The work shall also include providing and fixing 32 mm nominal bore copper alloy waste fitting with nickel-chromium plated finish, including all necessary washers, nuts, gaskets and accessories, painting of cast iron brackets and exposed fittings with approved paint, sealing the gap between the wash basin and wall with approved silicone sealant, cutting and making good the wall wherever required, connecting to existing water supply pipes, waste pipes and waste fittings, including all necessary joints, connections, testing for leakage and satisfactory functioning, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 8 | Supply and fixing in repairs of single-lever centre-hole wash basin mixer, cast copper alloy body with chromium-plated finish, high-pressure type, complete with single operating lever, ceramic disc cartridge, aerator, long screwed shanks and fixing nuts suitable for connection to 15 mm bore iron water supply pipes, including 32 mm nominal size plain waste fitting without pop-up waste mechanism, all necessary washers, rubber gaskets, seals, nuts, connectors and fixing accessories. The work shall include dismantling and removal of the existing defective mixer, preparation of existing pipe connections, fixing and aligning the new mixer securely in position, connecting hot and cold water supply pipes, connecting the waste fitting, testing for leakage and satisfactory operation, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 9 | Supply and fixing in repairs of 15 mm nominal bore, ISI-marked, chromium-plated long-body bib tap, made of high-quality cast copper alloy, complete with wall flanges, screwed connection suitable for fixing to existing iron pipe or brass ferrule, including all necessary washers, PTFE tape, sealing materials, nuts and other fixing accessories. The work shall include dismantling and removal of the existing defective bib tap, cleaning and preparation of the existing pipe threads, fixing the new bib tap securely in position, ensuring proper alignment and leak-proof connections, testing for smooth operation and water-tightness, including all necessary labour, tools and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. Approved makes/models: Jaquar – Continental Series/ Hindware – Contessa Plus Series/ Cera – Ocean Series |
| 10 | Supply and fixing in repairs of health faucet with ABS body, complete with mild steel chromium-plated spray nozzle/trigger assembly, suitable for connection to 15 mm nominal bore water supply pipe, including 1.25 metre long flexible connecting tube, ABS wall hook/holder, all necessary washers, rubber gaskets, connectors, nuts and fixing accessories. The work shall include dismantling and removal of the existing defective health faucet, making necessary connections to the existing water supply pipe, fixing the wall hook securely in position, ensuring leak-proof connections, testing for proper water flow and satisfactory operation, including all necessary labour, tools and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 11 | Taking up or down carefully existing 15 mm bore steel tubing and connections, including dismantling of all necessary joints, fittings, bends, tees, sockets, unions, clamps and other accessories, without causing unnecessary damage to the tubing or fittings, cleaning and removing rust, scale, dirt and other deposits, sorting and stacking serviceable materials for refixing at site or depositing the dismantled materials in the departmental store, as directed by the Engineer-in-Charge, or handing over the materials for taking on Schedule of Credit, as applicable, including all necessary labour, tools, tackles and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 12 | Taking up or down carefully existing 20 mm bore steel tubing and connections, including dismantling of all necessary joints, fittings, bends, tees, sockets, unions, clamps and other accessories, without causing unnecessary damage to the tubing or fittings, cleaning and removing rust, scale, dirt and other deposits, sorting and stacking serviceable materials for refixing at site or depositing the dismantled materials in the departmental store, as directed by the Engineer-in-Charge, or handing over the materials for taking on Schedule of Credit, as applicable, including all necessary labour, tools, tackles and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 13 | Supply and fixing of 16 mm outside diameter CPVC pipe, SDR-11, having nominal bore of 15 mm, along with matching plain CPVC fittings of SDR-11, suitable for hot and cold water supply, conforming to relevant IS specifications, including all necessary bends, elbows, tees, sockets, couplings, reducers, unions, adaptors and other specials, solvent cement and jointing materials, cutting, fitting, jointing and fixing securely to walls and ceilings with approved clamps and supports or laying in floors, as required, including making proper connections with existing pipework, maintaining correct alignment and gradients, pressure testing the completed pipeline for leakage and ensuring satisfactory operation, including all materials, labour, tools, tackles and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 14 | Supply and fixing of 20 mm outside diameter CPVC pipe, SDR-11, having nominal bore of 15 mm, along with matching plain CPVC fittings of SDR-11, suitable for hot and cold water supply, conforming to relevant IS specifications, including all necessary bends, elbows, tees, sockets, couplings, reducers, unions, adaptors and other specials, solvent cement and jointing materials, cutting, fitting, jointing and fixing securely to walls and ceilings with approved clamps and supports or laying in floors, as required, including making proper connections with existing pipework, maintaining correct alignment and gradients, pressure testing the completed pipeline for leakage and ensuring satisfactory operation, including all materials, labour, tools, tackles and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 15 | Supply and fixing in replacement of 20 mm bore gunmetal globe valve or gate valve, of approved make and quality, complete with cast iron/metal wheel head, screwed ends suitable for connection to existing 20 mm bore iron pipes, including necessary sockets, unions, nipples, washers, jointing materials, PTFE tape and other accessories required for proper installation. The work shall include dismantling and removal of the existing defective valve, preparation and cleaning of pipe threads, fixing the new valve in the required position with proper alignment, making all threaded connections leak-proof, testing under working water pressure and ensuring smooth operation, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 16 | Supply and fixing in repairs of 15 mm nominal bore, non-rising spindle type fancy stop valve/angle valve, conforming to IS 8931:1993, manufactured from high-quality cast brass, with nickel-chromium plated finish, complete with operating knob, knob components, spindle, internal valve mechanism, divertor and all associated components and accessories. The work shall include dismantling and removal of the existing defective stop valve/angle valve, cleaning and preparation of existing pipe threads, providing and fixing the new valve at the required location, making threaded connections to the existing 15 mm nominal bore water supply pipe, including necessary washers, seals, PTFE tape and jointing materials, ensuring proper alignment and leak-proof connections, testing under working water pressure and ensuring smooth operation, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 17 | Supply and fixing in repairs of 125 mm diameter brass chromium-plated shower rose, with or without swivel joint, of approved make and premium quality, suitable for connection to existing steel pipe or union, including dismantling and removal of the existing defective shower rose, cleaning and preparation of threaded connections, providing and fixing the new shower rose in position with all necessary washers, seals, PTFE tape, jointing materials and accessories, ensuring proper alignment and leak-proof connection, testing for uniform water distribution, satisfactory flow and functioning under working water pressure, complete in all respects, all as specified and directed by the Engineer-in-Charge. Approved makes: Jaquar/ Hindware/Cera |
| 18 | Material and labour for providing and fixing in repairs 15 mm nominal bore PVC flexible connection pipe, 600 mm long, complete with PTMT (Polytetra Methylene Terephthalate) nuts at both ends, suitable for connection to existing water supply fittings, wash basins, sinks, flush cisterns and other sanitary fixtures, including necessary rubber washers, gaskets, sealing materials and accessories, dismantling and removal of existing defective connection, connecting securely to the existing supply pipe and sanitary fitting, ensuring leak-proof joints, testing under working water pressure and making the installation fully functional, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 19 | Supply and fixing in repairs of 600 mm long PTMT (Polytetramethylene Terephthalate) towel rail, of approved quality and design, having a minimum weight of 190 grams, complete with chromium-plated brass screws, suitable wooden/plastic cleats, brackets, end supports and all necessary fixing accessories. The work shall include dismantling and removal of the existing defective towel rail, marking and drilling holes in the wall, fixing the cleats and brackets securely with suitable fasteners, mounting and aligning the towel rail horizontally, including all necessary labour, tools, tackles and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 20 | Supply and fixing in repairs of fancy type oval-shaped soap dish with chromium-plated finish, of approved make, design and quality, manufactured from brass/approved corrosion-resistant material, complete with soap-holding tray, wall mounting bracket, base plate, chromium-plated screws, suitable wall plugs and all necessary fixing accessories. The work shall include dismantling and removal of the existing defective soap dish, drilling holes in the wall, fixing the new soap dish securely in position, ensuring proper alignment and firm installation, including all necessary labour, tools, tackles and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 21 | Supply and fixing in replacement of vitreous china half-stall type urinal, white colour, of approved make, quality and design, as approved by GE, including taking down carefully the existing defective urinal along with its fittings and accessories, removing the old bedding and cleaning the fixing surface. The new urinal shall be installed against the wall in cement mortar (1:2), including providing and fixing suitable wall plugs and securing the urinal firmly with 60 mm long brass screws. The work shall also include providing and fixing 32 mm diameter full-threaded PTMT waste coupling, 32 mm diameter waste pipe and water spreader, making all necessary connections to the existing flushing water supply and waste disposal system, pointing around the back and sides of the urinal with cement mortar (1:2), sealing all joints, ensuring proper alignment and level, testing for leakage and satisfactory flushing and drainage, including all necessary materials, labour, tools, tackles and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 22 | Taking down carefully existing chowkhats/frames complete with shutters, including PVC door frames, wooden door frames, wooden door shutters, wooden window shutters, mild steel window frames and mild steel ventilator frames, without removing the shutters from their respective frames, for openings having an area not exceeding 1.50 Sqm each, including dismantling of holdfasts, screws, bolts, hinges and other fixing arrangements as required, without causing unnecessary damage to the adjoining structural members, walls or finishes. The work shall also include removal of dismantled materials, cleaning of the opening, cutting and removal of loose mortar, and making good the disturbed surfaces around the finished opening with cement mortar plaster/rendering to match the existing adjoining surface, including necessary materials, labour, tools, tackles and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 23 | Taking down carefully existing chowkhats/frames complete with shutters, including PVC door frames, wooden door frames, wooden door shutters, wooden window shutters, mild steel window frames and mild steel ventilator frames, without removing the shutters from their respective frames, for openings having an area exceeding 1.50 Sqm but not exceeding 4.00 Sqm each, including dismantling of holdfasts, screws, bolts, hinges and other fixing arrangements as required, without causing unnecessary damage to adjoining structural members, walls or finishes. The work shall also include removal of dismantled materials, cleaning of the opening, cutting and removal of loose mortar, and making good the disturbed surfaces around the finished opening with cement mortar plaster/rendering to match the existing adjoining surface, including necessary materials, labour, tools, tackles and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 24 | upply and fixing of factory-manufactured, single-extruded WPC (Wood Polymer Composite) solid door frame/chowkhat of size 45 mm × 70 mm, manufactured using virgin suspension-grade PVC polymer having K-value 58–60, calcium carbonate, natural fibres (wood powder/rice husk/wheat husk) and non-toxic additives, with maximum toxicity index of 12 for 100 grams of material. The WPC door frame shall have a minimum density of 750 kg/m³, screw withdrawal strength of 2,200 N (face) and 1,100 N (edge), minimum compressive strength of 508 N/Sqmm, modulus of elasticity of 900 N/Sqmm, and resistance to spread of flame of Class A category, with properties of being termite-proof, borer-proof, moisture-resistant, waterproof and fire-retardant. The frame shall be factory-fabricated with accurately cut mitred joints, bonded using approved PVC solvent cement and secured with full-body threaded, star-headed stainless steel screws. The work shall include supplying, cutting, assembling and fixing the frame in position, including MS holdfasts/SS dash fasteners, 3 Nos. per frame, and supplying and fixing 100 mm long stainless steel butt hinges, including all necessary screws, fasteners, packing, levelling, plumbing, alignment, grouting and making good the adjoining surfaces, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 25 | Supply and fixing of factory-manufactured, single-extruded WPC (Wood Polymer Composite) solid plain flush door shutter, 30 mm thick, manufactured using virgin suspension-grade PVC polymer having K-value 58–60, calcium carbonate, natural fibres (wood powder/rice husk/wheat husk) and non-toxic additives, with maximum toxicity index of 12 for 100 grams of material. The WPC door shutter shall have a minimum density of 650 kg/m³, screw withdrawal strength of 1,800 N (face) and 900 N (edge), minimum compressive strength of 50 N/Sqmm, and resistance to spread of flame of Class A category, with properties of being termite-proof, borer-proof, moisture-resistant, waterproof and fire-retardant. The work shall include supplying, cutting, sizing, fitting and fixing the shutter in the approved WPC door frame, including providing and fixing 2 Nos. 150 mm long stainless steel tower bolts and 2 Nos. 150 mm long stainless steel handles per shutter leaf, complete with all necessary screws, fasteners, fittings and accessories, including adjustment of clearances, proper alignment, smooth operation, testing and making good wherever required, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 26 | Supply and fixing factory made uPVG white colour Sliding window area not exceeding 2.00 Sqm Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note :- 5mm thick toughened Glass and stainless steel wire shall be included in this item nothing shall be paid extra in this account. Net Opening will be measured lor payment purpose.) |
| 27 | Material and labour for providing and fixing 20 mm thick granite stone (any type, colour and shade as approved), table-rubbed and polished, in steps, jambs, pillars, window cills, cooking platforms, counters, shelves, urinal partitions and similar locations, laid and fixed in cement mortar (1:4), over and including 15 mm thick screed/bedding layer in cement mortar (1:4), including cutting, dressing, shaping, levelling and aligning the granite slabs to the required size and profile; grinding, moulding and rounding of exposed edges to the required finish; pointing of joints with white cement mortar (1:2), using marble dust and admixture of pigment to match the shade of granite; filling and finishing joints neatly, rubbing, polishing and cleaning the finished surface, including all necessary materials, labour, tools, tackles, wastage and incidental works, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 28 | Dismantling and removing existing mud roofing, of any thickness, including removal of the complete or partial thickness of mud layer, along with existing plastering and leeping/finishing, as required; carefully taking up and removing all dismantled material, loosening and clearing the roof surface without causing damage to the structural roof slab or adjoining works, collecting, loading, transporting and disposing of the dismantled material and rubbish to a distance not exceeding 500 metres at a location as directed by the Engineer-in-Charge, including all labour, tools, tackles and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 29 | Material and labour for providing and applying waterproofing treatment to existing roof/terrace using an approved single-component, acrylic-based, flexible, micro-fibre-reinforced waterproofing and heat-reflective coating system, of an approved make and type, as approved by GE, strictly in accordance with the manufacturer's recommendations and approved method statement, including the following operations:(a) Preparing the existing roof/terrace substrate by removing all loose, friable and unsound material by mechanical means, thoroughly cleaning the surface and making it suitable to receive the waterproofing treatment.(b) Identifying and opening existing cracks along their full length to form V-grooves, 5–10 mm wide/deep, using a suitable cutter, hammer or chisel, cleaning the grooves and filling them with approved crack filler and PU sealant, complete.(c) Applying one coat of compatible primer at the rate of 0.20–0.30 kg/sqm, followed by the first coat of acrylic-based waterproofing compound at the rate of 0.75 kg/sqm, uniformly over the prepared surface.(d) Applying the second coat of waterproofing compound at the rate of 0.75 kg/sqm after the first coat has dried sufficiently, with approved fabric reinforcement embedded between the first and second coats, ensuring proper overlap, bonding and continuity of the reinforcement.(e) After the second coat has dried, applying the final/top coat of compatible primer at the rate of 0.05–0.08 kg/sqm, as recommended by the manufacturer, to achieve the specified finish and performance.Technical requirements of the waterproofing material/system:Property Required specification Test standardTensile strength 1.5 MPa ASTM D412Elongation at break More than 200% ASTM D412Adhesion in peel More than 1.5 MPa on concrete substrate EN 1542Crack-bridging ability Passes up to 3.2 mm crack width ASTM C1305Water vapour permeability Passes IS 2645Water vapour transmission Approximately 23 g/m²/24 hours ASTM E96Water absorption Less than 10% by mass ASTM D570Microbiological resistance No algae or fungal growth ASTM D5590Solar Reflectance Index (SRI) 102 ASTM E1980The complete waterproofing system shall be of a single approved manufacturer, including primer, waterproofing coating, fabric reinforcement, crack filler, PU sealant and all other auxiliary materials and accessories. Any component not manufactured by the approved manufacturer shall be used only with the manufacturer's written approval and in consultation with GE. The application shall be carried out by an installation agency trained and authorised by the manufacturer, strictly as per the manufacturer's approved method statement. The complete material shall be submitted for approval of GE, procured in bulk and kept in safe custody under lock and key. The item shall include all materials, labour, surface preparation, crack treatment, application, curing/drying between coats, tools, tackles, access arrangements and incidental operations necessary to provide a continuous and effective waterproofing system, complete in all respects, all as specified and directed by the Engineer-in-Charge |
| 30 | Material and labour for providing 40 mm average thick PCC padding in cement concrete 1:2:4, Type B-1, using 20 mm graded stone aggregate, as roof slab finishing, including preparation and cleaning of the existing roof slab surface, wetting the surface, mixing, laying, compacting and finishing the concrete to the required average thickness, maintaining the necessary slope towards rainwater outlets, and finishing the top surface even, fair and smooth as required, including mixing and incorporating liquid waterproofing compound in the concrete as per the manufacturer's instructions and specified dosage, complete in all respects, all as specified and directed by the Engineer-in-Charge.Note:(i) Liquid waterproofing compound shall be measured and paid for separately under the appropriate supply-only item of Schedule 'A' of the BOQ.(ii) Supply of liquid waterproofing compound is excluded from this item. Incorporation of the separately supplied compound in the concrete, including labour, shall be deemed included.(iii) Measurement shall be based on the finished roof area treated. |
| 31 | Material and labour for applying cement slurry at the rate of 1.20 kg/sqm, uniformly spread over the prepared roof surface using a suitable bristle brush, followed by providing and applying 15 mm average thickness rendering in cement mortar (1:3), including mixing and incorporating liquid waterproofing compound at the rate of 200 ml per 50 kg bag of cement, thorough mixing, laying, compacting and finishing the surface even and fair to the required line, level and slope, including curing and all necessary preparatory works, complete in all respects, all as specified and directed by the Engineer-in-Charge.Notes:(i) Liquid waterproofing compound shall be measured and paid for separately under the appropriate supply-only item of Schedule 'A' of the BOQ.(ii) Cost of incorporation of the separately supplied waterproofing compound, including labour, shall be deemed included in this item.(iii) The 15 mm thickness shall be measured as the average finished thickness of the rendering. |
| 32 | Material and labour for providing and forming PCC benching in cement concrete 1:2:4, Type B-0, using 12.5 mm graded stone aggregates, along the junction of roof surface and adjoining parapet/wall, finished in a continuous concave (coving) shape to eliminate sharp corners and facilitate proper drainage of rainwater, including preparation and cleaning of the junction surface, mixing and incorporating liquid waterproofing compound in the concrete as per the manufacturer's instructions and recommended dosage, laying, compacting, shaping and finishing the benching smoothly to the required profile, line and level, including curing and all necessary incidental works, complete in all respects, all as specified and directed by the Engineer-in-Charge.Notes:(i) Liquid waterproofing compound shall be measured and paid for separately as a supply-only item under the appropriate item of Schedule 'A' of the BOQ.(ii) Labour for mixing and incorporating the separately supplied waterproofing compound shall be deemed included in this item.(iii) The radius/profile and dimensions of the concave benching shall be as shown on drawings or as directed by the Engineer-in-Charge. |
| 33 | Supply only approved make and brand of liquid waterproofing compound, suitable for use in cement concrete and cement mortar, conforming to relevant applicable IS standards and compatible with the cementitious waterproofing system, in original sealed containers, complete with manufacturer's technical data sheet, batch number, manufacturing date, expiry date and recommended dosage/application instructions. The material shall be delivered at site, inspected and approved by GE/Engineer-in-Charge and stored in safe custody under lock and key, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 34 | Supply and fixing, in replacement, of 500-litre capacity, three-layer HDPE water storage tank, Polyproof or equivalent approved make, white in colour, manufactured by rotational moulding process from high-density polyethylene (HDPE), cylindrical vertical type with closed top, suitable for storage of potable water, complete with properly fitted and secured cover/lid. The tank shall be hoisted and placed in position on the existing prepared platform/support, including dismantling and removal of the existing unserviceable tank, wherever required, providing and fixing suitable-size inlet and outlet connections with necessary HDPE/PVC threaded adaptors, sockets, unions, washers, gaskets and other standard accessories, making all connections watertight, levelling, alignment, testing for leakage and commissioning, including all materials, labour, tools, tackles and incidental works, complete in all respects, all as specified and directed by the Engineer-in-Charge.Notes:(i) Overflow pipes and ball valves shall be measured and paid for separately under the appropriate supply-and-fixing items of Schedule 'A' of the BOQ.(ii) The tank shall be of 500-litre nominal capacity, three-layer construction, with UV-stabilised outer layer and suitable food-grade inner layer for potable water storage, supported by manufacturer's certificate.(iii) The rate shall include all necessary inlet/outlet connection accessories, but shall exclude overflow pipes and ball valves. |
| 35 | Supply and fixing, in replacement, of 20 mm bore high-pressure PTMT ball valve, minimum weight 210 grams, complete with epoxy-coated aluminium operating rod and high-density plastic float ball, suitable for connection to iron pipe, having screwed ends, including dismantling and taking down the existing unserviceable ball valve, preparation of pipe threads, providing suitable sealing material, connecting, tightening, adjusting the float mechanism and setting the water level, testing for proper operation and leakage, complete with all necessary accessories, labour and incidental works, in all respects, all as specified and directed by the Engineer-in-Charge. |
| 36 | Supply and fixing, in repair/replacement, of 75 mm nominal bore uPVC Type-B pipe, single-socketed type, of approved make and conforming to relevant applicable IS standards, in required lengths, with rubber ring push-fit joints, laid in trenches or in floors, including cutting, jointing, alignment, providing suitable rubber rings and necessary jointing accessories, connecting to existing pipework, making good disturbed flooring or surrounding surfaces, testing for leakage and ensuring proper flow, including all materials, labour, tools, tackles and incidental works, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 37 | Supply and fixing, in repair/replacement, of 75 mm nominal bore uPVC soil, waste and rainwater (SWR) pipe fittings, including bends of any radius, plain bends, tapers, reducers and other necessary fittings of approved make, compatible with the existing uPVC SWR pipework, including cutting, fitting, jointing with suitable rubber rings/solvent cement as recommended by the manufacturer, alignment, connection to existing pipework, testing for leakage and proper flow, including all necessary materials, labour, tools, tackles and incidental works, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 38 | Supply and fixing, in repair/replacement, of 25 mm diameter stainless steel (SS) curtain rod, of approved grade, finish and make, including fancy-type SS supporting brackets, decorative end knobs (finials), stop rollers/rings and all necessary accessories, cut to the required length and fixed to walls over doors and windows, including drilling holes, providing and fixing suitable rawl plugs, SS screws and other fixing arrangements, ensuring proper alignment and firm support. The item shall also include carefully taking down and removing existing curtain rods or pelmet boxes of any type, including associated fittings, and stacking/disposal of dismantled materials as directed by the Engineer-in-Charge, complete with all materials, labour, tools, tackles and incidental works, in all respects, all as specified and directed by the Engineer-in-Charge. |
| 39 | Material and labour for excavation in trenches in soft/loose soil, not exceeding 1.50 m in width and not exceeding 1.50 m in depth, for foundations of manholes, sewerage pipelines and similar works, including setting out, removal of vegetation and loose surface material, excavation to the required width, depth, line and level, dressing and levelling the bottom and sides of trenches, getting out the excavated soil and depositing it alongside the trenches at a suitable location for subsequent use or disposal, including all necessary labour, tools, tackles and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 40 | Demolition and breaking up of existing drain pipes of salt-glazed stoneware (SGSW), asbestos cement (AC) or reinforced cement concrete (RCC), of sizes up to and including 200 mm nominal bore, including excavation around the pipes wherever necessary, breaking and dismantling the pipes into manageable pieces, removing jointing materials, disconnecting from existing manholes/chambers and adjoining pipework, collecting and removing the dismantled pipe pieces and debris from the site, and depositing the same at a location as directed by the Engineer-in-Charge, including all labour, tools, tackles and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 41 | Material and labour for providing PCC bedding and haunching in cement concrete 1:3:6, Type C-2, using 40 mm graded stone aggregates, for 200 mm internal diameter drain pipes, including preparation and levelling of the trench bottom, laying and compacting concrete bed to the required line, level and gradient, carefully packing concrete underneath the pipe and providing haunching against both sides of the pipe after laying and testing, ensuring proper support, uniform bearing and stability without disturbing the alignment or damaging the pipe, including finishing, curing and all necessary incidental works, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 42 | Supply and fixing, including providing, lowering and laying of 200 mm internal diameter (ID) HDPE double-wall corrugated (DWC) pipe, SN-8 stiffness class, conforming to IS 16098 (Part 2):2013, suitable for underground drainage/sewerage applications, including transportation, handling, lowering into trenches, laying to the required line, level and gradient, jointing with suitable couplers and elastomeric sealing O-rings, ensuring proper seating and watertight joints strictly in accordance with the manufacturer's recommendations, including cutting, alignment, testing of joints, all necessary jointing materials, labour, tools, tackles and incidental works, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 43 | Material and labour for making connection of new drainage pipe of 200/300 mm internal diameter to existing manhole, including carefully cutting and breaking the existing manhole wall at the required location and level, forming an opening of suitable size, inserting and connecting the new drain pipe, properly sealing around the pipe with cement concrete/mortar to ensure a watertight connection, making good the disturbed masonry/concrete and rendering the exposed surfaces to match the existing finish. The item shall also include cutting and removing the existing benching as required, forming a new branch channel of 1/2-round to 3/4-section in cement concrete 1:2:4, Type B-1, smoothly finished to the required line, level and gradient, connecting it to the existing channel, and reforming the remaining benching to the required profile to ensure smooth flow without obstruction, including all necessary materials, labour, tools, tackles and incidental works, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 44 | Demolition and taking down existing brickwork built in cement mortar, including all quoins, jambs, pillars, projections, offsets and other similar portions, carefully breaking the masonry into manageable pieces, removing and separating the dismantled bricks and mortar, taking out embedded materials wherever required, and collecting the debris at site for stacking or disposal as directed by the Engineer-in-Charge, including all necessary labour, tools, tackles and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 45 | Material and labour for constructing brickwork in sub-class 'B' bricks of old size, laid in cement mortar 1:4, in straight or curved work on plan having a mean radius exceeding 6 metres, including soaking bricks, preparation of mortar, laying bricks in proper bond, maintaining uniform joints, raking out joints where required for subsequent pointing or plastering, forming quoins, jambs, corners and junctions, cutting and shaping bricks as necessary, scaffolding, curing and making good the work, including all necessary materials, labour, tools, tackles and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 46 | Demolition and breaking up of existing cement concrete of any description, in ground floor or at any position, not exceeding 15 cm in thickness, including breaking the concrete into manageable pieces by suitable mechanical or manual means, cutting and removing embedded portions wherever required, taking care not to damage adjoining structures, foundations, services or other existing works, collecting, loading and removing the demolished concrete debris from the work site and depositing it at a location as directed by the Engineer-in-Charge, including all necessary labour, tools, tackles, machinery and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 47 | Material and labour for providing and laying cement concrete 1:4:8, Type C-2, using 40 mm graded crushed stone aggregate, for foundations, fillings, mass concrete, sub-base and similar works, including preparation and dressing of the foundation bed, mixing cement, coarse sand and graded stone aggregates in the specified proportion, adding water to obtain the required consistency, laying concrete in position, compacting thoroughly by ramming or mechanical means, levelling and finishing to the required line, level and profile, including curing, all necessary materials, labour, tools, tackles and incidental works, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 48 | Material and labour for providing and laying cement concrete 1:2:4, Type B-1, using 20 mm graded crushed stone aggregate, for manhole benching, flooring, coping and similar works, including preparation and dressing of the base, mixing cement, coarse sand and graded crushed stone aggregate in the specified proportion, adding water to obtain the required consistency, laying concrete in position, compacting thoroughly, shaping and finishing to the required line, level, slope and profile, including smooth finishing wherever required, curing, and all necessary materials, labour, tools, tackles and incidental works, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 49 | Taking down existing cement plaster from brickwork or concrete surfaces, including carefully removing the plaster without causing damage to the underlying masonry or concrete, raking out mortar joints to the required depth, hacking the surface to provide adequate key for receiving new plaster, removing all loose mortar and plaster particles, scrubbing and washing down the exposed surface with clean water, and collecting and removing the dismantled plaster debris to a location as directed by the Engineer-in-Charge, including all necessary labour, tools, tackles and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 50 | Material and labour for providing and applying 15 mm thick cement plaster in cement mortar 1:4 on fair or unfair faces of brickwork or concrete surfaces, including preparation of the background by cleaning, wetting and raking out joints wherever required, applying and finishing the plaster to an even, smooth and uniform surface without using extra cement, including mixing and incorporating liquid waterproofing compound (WPC) at the rate of 200 ml per 50 kg bag of cement, as per the manufacturer's instructions, proper curing and all necessary materials, labour, tools, tackles and incidental works, complete in all respects, all as specified and directed by the Engineer-in-Charge.Notes:(i) Liquid waterproofing compound (WPC) shall be measured and paid for separately under the appropriate supply-only item of Schedule 'A' of the BOQ.(ii) Labour for mixing and incorporating the separately supplied WPC in the mortar shall be deemed included in this item. |
| 51 | Demolition and breaking up of reinforced cement concrete (RCC) in slabs, parapets, chajjas, fins, fascias and similar structural members, of any description and in any position, not otherwise specifically provided for, including cutting and removing reinforcement bars as required to facilitate demolition, breaking the concrete into manageable pieces by suitable mechanical or manual means, carefully dismantling the work without causing damage to adjoining structures or services, collecting, lowering, loading and removing the demolished concrete and reinforcement debris from the site, and depositing the same at a location as directed by the Engineer-in-Charge, including all necessary labour, tools, tackles, machinery, safety arrangements and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 52 | Material and labour for providing and fixing formwork/shuttering to soffits of suspended slabs, such as roof slabs, floor slabs, landings, beams, chajjas and similar works, having thickness not exceeding 200 mm, whether horizontal or sloping, including providing and fixing suitable shuttering plates, supports, props, staging, bracing, wedges, ties and necessary framework, applying approved shuttering oil/release agent, ensuring proper line, level, camber and alignment, making joints tight to prevent leakage of cement slurry, and maintaining the formwork rigid and stable during concreting, including removal of formwork after the concrete has attained the required strength, cleaning and stacking of shuttering materials, complete to receive fair-finished concrete surfaces, all as specified and directed by the Engineer-in-Charge. |
| 53 | Material and labour for providing and fixing high-yield strength deformed (HYSD) TMT steel reinforcement bars of grade Fe 500/Fe 550D, 6 mm to 8 mm diameter, cut to required lengths, bent and shaped as per bar bending schedule and structural drawings, including straightening, cutting, bending, cranking, forming spirals/helical reinforcement for column ties/hoops, providing hooks and bends at ends, placing and securing in position, including binding with and providing mild steel annealed binding wire of minimum 0.9 mm diameter or suitable approved clips, including all necessary laps, bends, hooks, wastage, handling, tools and tackles, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 54 | Material and labour for returning and filling excavated earth in trenches, foundations, plinths and other required locations, including spreading the earth in layers not exceeding 25 cm thick each, breaking clods, removing unsuitable material, levelling and dressing each layer, watering to optimum moisture content and well ramming/compacting each layer to achieve proper consolidation, including all necessary labour, tools, tackles and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 55 | Removal and disposal of excavated earth/soil from trenches, foundations and other excavations, including lifting, carrying and depositing the excavated material at a location directed by the Engineer-in-Charge, involving a vertical lift not exceeding 1.5 metres above the starting point, including all necessary labour, handling, tools, tackles and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 56 | Supply and fixing, in repair/replacement, of heavy-duty steel fibre reinforced concrete (SFRC) manhole cover and frame, HD-20 grade designation, having clear cover size of 900 mm × 900 mm, conforming to IS 12592 (latest applicable revision), complete with properly reinforced cover and matching frame, including carefully removing the existing damaged cover and frame, preparing the seating, providing and fixing the new frame in cement concrete 1:2:4, ensuring correct line, level and alignment, proper bedding and firm seating of the cover, making good the surrounding concrete/masonry, and testing for proper seating and operation, including all materials, labour, tools, tackles and incidental works, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 57 | Cleaning and de-sludging of existing septic tank of any capacity and at any depth by removing accumulated semi-solid sludge, settled solid contents and other deposits manually or mechanically, including opening and removing manhole covers, pumping out liquid contents, breaking and loosening hardened sludge wherever necessary, using suitable sludge pumps, suction machines, tankers and other necessary tools and plants, collecting, loading, transporting and disposing of the sludge and solid contents at an authorised disposal facility in accordance with applicable environmental and public health regulations, including cleaning the internal walls, floor and baffles of the septic tank, washing and flushing with water, and leaving the tank clean and ready for reuse, complete with all labour, equipment, safety arrangements and incidental operations, all as specified and directed by the Engineer-in-Charge. |
| 58 | Dewatering of existing soakage well/septic tank by bailing out, pumping out or by any other suitable means, including deployment of suitable dewatering pumps, hoses, pipes, electrical connections, labour, tools and tackles, and conveying and discharging the pumped-out water into the existing open drain or nearby designated low-lying area, as directed by the Engineer-in-Charge, including all necessary arrangements for uninterrupted pumping, removal of residual water and incidental operations, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 59 | Supply and fixing of 100/110 mm nominal diameter uPVC Type-B pipe, single-socketed, ISI marked, conforming to the relevant applicable IS standard, in required lengths, with rubber ring push-fit joints, laid in trenches or floors, including all necessary compatible uPVC fittings such as bends, tees, junctions, reducers, couplers and other accessories required for completing the pipework, cutting, jointing, alignment, maintaining the required line, level and gradient, connecting to existing pipework, providing rubber sealing rings, testing for leakage and proper flow, including all materials, labour, tools, tackles and incidental works, complete in all respects, all as specified and directed by the Engineer-in-Charge. |
| 60 | Supply and fixing, in replacement, of 110 mm nominal diameter uPVC soil, waste and rainwater (SWR) pipe bend, of approved make, ISI marked and conforming to the relevant applicable IS standard, of required angle and radius, suitable for jointing with existing 110 mm uPVC SWR pipework, including cutting, fitting, jointing with suitable rubber ring/solvent cement as recommended by the manufacturer, alignment, connection to existing pipework, testing for leakage and proper flow, including all necessary materials, labour, tools, tackles and incidental works, complete in all respects, all as specified and directed by the Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 12, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 26, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysNov 28, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender