Tender For Mtps- Ii - Mill Plant Division - Renewal Of Worn Out Hot Air Gate Seals In 4 Nos Of Hot Air Gates E To H During Coh Of 2026
Tender Value
Ref. Documents
Estimated cost
Bid Submission
26 Nov 2026
9 days left
EMD
8500
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Salem → Tamil Nadu
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Mtps- Ii - Mill Plant Division - Renewal Of Worn Out Hot Air Gate Seals In 4 Nos Of Hot Air Gates E To H During Coh Of 2026
BOQ
| Sl. No. | Item Description |
| 1 | Charges for removing the damaged / worn out bunch of Haste alloy spring seal assemblies of frame top in the existing hot air gate plate entering top surface of duct, fixing the new bunch of SS seal assembly with proper setting & aligning the seals and additionally fixing the top side seals etc… Finally checking the Hot air gate smooth operation for ensuring the sliding gate piercing into the seal beam assembly for arresting of hot air gate leaks etc..(Required qty. of Asbestos ropes are under contractor scope). |
| 2 | Charges for removing the all inspection doors of hot air gate side walls, removing the damaged / worn out bunch of Haste alloy seal assembly from the existing hot air sliding gate seating duct side walls & bottom walls, fixing the new Haste alloy seal assembly of duct frame left vertical & right vertical side seals, Frame bottom seals with proper setting & aligning the seals and additionally fixing the frame vertical & bottom side seals etc… Finally checking the Hot air gate smooth operation for ensuring the sliding gate piercing into the seal beam assembly for arresting of hot air gate leaks etc. (Required qty. of Asbestos ropes are under contractor scope ). |
| 3 | Charges for dismantling the pneumatic operated power cylinder from the hot air gate & lower down to the mill repair bay, remove the end caps, piston shaft with flange, lock nut etc… one by one, cleaning, checking and inspecting the piston seals, ‘o’ rings & renewal of worn out parts etc… if necessary, reassembling to the hot air gate body and checking the trouble free operation of hot air gate movement etc... More care to be taken while renewal of seals in Hot air gate cylinder. If damaged, free replacement shall be made at free of cost. (Portable type air compressor for checking the cylinder & gate operation (8 kg. pressure) is to be provided by contractors if necessary to complete the work within time as service air will not be available during Unit overhauling period). |
| 4 | Charges for cutting and removing the wornout seal holding plates of size 1700x150mm in the hot air duct and refixing the new MS plate of the required size after assembling the hot air duct SS seals including cost of consuables and T&Ps etc., (required 10mm tk MS plates contractor's scope) |
| 5 | Hot PA shut off gate cylinder seals |
| 6 | Hot PA vertical gate cylinder seals |
| 7 | Supply of M10X 50 mm full thread bolt, nut & plain washer |
| 8 | Charges for fabrication of inspection doors of hot air gate side walls (04 Nos), Bottom walls (02 Nos) of size 500mm x 250 mm X 6 mm thick with hand rails, cuttuing and champering the edges,providing holes as per direction of Engg in Charge. (Required quantity of MS plate supplied by TNPGCL). |
| 9 | Charges for removal of insulation over the hot air gate area, this work involves removal of insulated metal Sheet, wool mattress, gas cutting, removal of retainers and casing supports and etc… |
| 10 | Charges for providing insulation over the hot air gate out side frame in coal mills, this work involves cleaning, welding of Pin & retainers, laying of wool mattress (New/released) sewing the joint of mattress by GI wire, screwing the casing support with retainer wounding the G.I binding wire across the retainer including consumables such as Screw, Binding wire, welding electrodes, T&P’s and other consumables etc., |
| 11 | Charges for fixing and removing the scaffolding arrangements for renewing the hot air gate seals in the hot air duct (size:3mX3m) |
| 12 | Supply of various sizes of SS Seals for Hot air gates/No Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 12, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 26, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysNov 27, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 10 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender