Power Government Departments Closing in 16 days TDR #58500960

Bids Are invited for Repair, Maintenance, And Installation Of Plant/ Systems/Equipments (Version 2) - In The Area Of Eutd-1 2 Aligarh; Electrical System Or Installation; On Semi Turnkey Basis - Shifting Of 11 Kv & L.T. Lines , Safe Carriage Of Follow

Issued by Government Departments · Aligarh, Uttar Pradesh
Tender Value
25 Lakhs
Estimated cost
Bid Submission
04 Dec 2026
16 days left
EMD
30000
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Gem

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Aligarh → Uttar Pradesh
EMD Exemption
Not Available
Quantity
1

Project Description

Bids Are invited for Repair, Maintenance, And Installation Of Plant/ Systems/Equipments (Version 2) - In The Area Of Eutd-1 2 Aligarh; Electrical System Or Installation; On Semi Turnkey Basis - Shifting Of 11 Kv & L.T. Lines , Safe Carriage Of Following Materials From Store Centre Or Any Other Place To The Respective Site Of Work Through The Kachha/Pacca Road Including Loading, Unloading At The Respective Ends And Erection Of Same Including The Work Of Dragging As Per Site Requirement, Jumphering Of Transformer With 11 Kv Line Through Lt Abc Cable, Weasal Conductor Etc. Cost Of Labour, T&P Carrier Etc. Required For Proper Completion Of Work As Per Respo Norms Is Included In The Work. , 11Kv Xlpe Cable 3X185 Mm2 (For Road Crossing) , Lt Abc (3X120+1X70+1X16) Sqmm , St Pole 11 Meter (For Make Double Pole) , St Pole 9 Meter , 11Kv Disk Insulator With Fitting , Earthing Complete , Acsr Dog Conductor , Lt Xlpe Cable 3.5X400mm2 , Lt Xlpe Cable 3.5X240mm2 , Lt Xlpe Cable 1X120mm2 , V-Type Cross Arm , Stay Set , Lt Distribution Box 3 Phase With Clamp , Cable Jointing Kit 3X185sq.Mm. Outdoor Type , 11Kv Pin Insulator With Pin , 11Kv Tpmo Set , 11Kv Do Fuse Set , Supply, Fixing And Erection Of Following Materials As Per Site Requirement As Per Respo Norms:- , Stone Pad , Cross Braccing Angle , Nut Bolt & Washer , Barbed Wire , Danger Board , Pg Clamp , Number Plate , Aluminium Paint , Rex Oxide Paint , Top Channel , Dropper Channel , Dp Holding Clamp , T/F Base Channel , Alumunium Lug 400Mmsq , Alumunium Lug 240Mmsq , Alumunium Lug 120Mmsq , T-Off Channel , Pg Clamp , F-Bracket , Winding Wire 6 Swg , Suspension Clamp With Eye Hook , Lt Piercing Connector For 120/50Mm , Dead End Clamp With Eye Hook , Concreting Of Support , Concreting Of Stay , Neutral & Body Earthing Of Distribution Transformer By Digging Of Pit Upto Water Level And Then Inserting 1-¼ Dia Gi Pipe Of ‘A Grade, Conforming To The Requirement Of Is Specification And Then Connecting The Top Of The Inserted Pipe And Transformer Body Through Gi Strip Of Size 40X6 Mm With The Help Of Nut And Bolt Or Through Gas Welding, As Per Direction Of Supervising Engineer. It Includes The Cost Of All Material Labour, T&P, Carrier Etc. Required For Proper Completion Of Work. The Aforesaid Work Shall Be Carried Out As Per Resspo Norms. , Construction Of Plinth At Various 11/0.4 Kv Sub-Station Suitable For Distribution Transformer Having Size 2X2x1.5 Mtr. Work Will Include Digging Of Foundation 2 Deep & Brick Work With Ist Class Bricks Having Cement And Sand Mortar Of Ratio 1:6 On All The Walls, Each Of 9 Thickness. The Area Inside The Wall Shall Be Duly Filled By Mud Up To The Height Of Appropriate Level From Ground Level And Shall Be Duly Watered & Rammed. Above The Filling C.C. Of Ration 1:6:12 (Cement Sand And Brick Ballast) Giving 4 Layer Shall Be Provided. Above C.C. Layer Rcc Layer Having 4 Thickness And With Ratio 1:2:4 Of Cement Sand And Stone Ballast Shall Be Provided Re-Enforcement Shall Be Provided By Providing Net Of (8 Nos. + 8 Nos.) M.S. Rods Of Size 10 Mm Dia And Each Of 2M Length In The Middle Of The Top Of C.C. Layer. The Plinth Shall Be Plastered With 12Mm Thick Plaster In Ratio 1:4 At All Sides. This Work Will Include Cost Of Labour, T&P And All Material Required For Construction Of Plinth Which Shall Be Provided By The Contractor As Per Resspo Norms. , Providing And Fixing Of Welded Wire Mesh Fencing Around Transformer Plinth With M.S. Angle Of Size 35X35x6 Mm. Length And 1.20 Meters Height, Such Panels Shall Be Supported On M.S. Angle From Of Size 40X40x6 Mm. Having 04 Nos. Corner Supports Of Height 1.65 Meters Including Extended Legs For Grouting Which Will Be Used As A Door For Entry Of The Personnel Or Removal/Shifting Of Transformer With Welded Hinges, Sliding Belt Etc. For Locking The Arrangement As Per Drawing And Specifications The Fencing Will Be Painted One Coat Of Red Oxide Primer And Then Two Coats Of Bus Green Synthetic Enamel Paint. The Rates Should Be Inclusive Of All Materials Required For Proper Completion Of Above Work (Length Of Each Fencing Approx. 11 Meters) , Supply, Fixing And Erection Of Following Materials As Per Site Requirement As Per Respo Norms:- , 11Mtr S.T. Pole (Scrap) (17+13 = 30 X175kg/Pole) , Weasel Conductor (Scrap) (540Mtr. X 0.109Kg/Meter) , Dog Conductor (Scrap) (2000Mtr. X 0.335Kg/Meter) , Other Line Material Scrap Such As Cross Arm, Clamp, Angle, Channel, Pin Etc. (17+13=30No. /8Kg/Pole) , 9Mtr. S.T. Pole Scrap (10No. X 123Kg/Pole) , L.T. Ab Cable Scrap (440+50 = 490 X 1.17X 0.8 = 459Kg) , Shifting Of 33 Kv Lines , Safe Carriage Of Following Materials From Store Centre Or Any Other Place To The Respective Site Of Work Through The Kachha/Pacca Road Including Loading, Unloading At The Respective Ends And Erection Of Same Including The Work Of Dragging As Per Site Requirement, Jumphering Through Xlpecable, Weasal Conductor Etc. Cost Of Labour, T&P Carrier Etc. Required For Proper Completion Of Work As Per Respo Norms Is Included In The Work. , St Pole 13 Meter (For Make Single Support / Double Pole) , 33Kv Disc Insulator 70Kn , 33Kv Disc Fitting , 33Kv Pin Insulator , 33Kv Pin With Nut , Earthing Complete , 33Kv V-Type Steel Cross Arm , Stay Set , Acsr Dog Conductor , Supply, Fixing And Erection Of Following Materials As Per Site Requirement As Per Respo Norms:- , G.I. Angle Iron 65X65x6mm. 4300Mm Long Bracing With 04 No. Clamps , G.I. Top Channel (125X65x6mm. 3200Mm Long) , Stone Pad 300X300x75mm. , Clmap With Bolt, Nut & Washer , Number Plate , Danger Board , Gi Barbed Wire , Aluminum Tape , Aluminum Paint , Nut , Bolt & Washer , Red Oxide Paint , Guarding Angle (For Guarding Of 33 Kv Lines) , Guarding Clamp , Gi Wire 8Swg , Gi Wire 6Swg , Concreting Of Support , Concreting Of Stay , Supply, Fixing And Erection Of Following Materials As Per Site Requirement As Per Respo Norms:- , Dog Conductor Scrap (8500 Mtr.) , 13 Mtr. S.T. Pole Scrap (40 No.) , Iron Scrap 102 No.

BOQ

Sl. No. Item TitleItem Description
1SHIFTING OF 11 KV & L.T. LINESSHIFTING OF 11 KV & L.T. LINES
2Safe carriage of following materials from Store centre or any other place to the respective site of work through the Kachha/Pacca road including loading, unloading at the respective ends and erection of same including the work of dragging as per site requirement, jumphering of Transformer with 11 KV line through LT ABC cable, Weasal conductor etc. Cost of labour, T&P carrier etc. required for proper completion of work as per RESPO Norms is included in the work.Safe carriage of following materials from Store centre or any other place to the respective site of work through the Kachha/Pacca road including loading, unloading at the respective ends and erection of same including the work of dragging as per site requirement, jumphering of Transformer with 11 KV line through LT ABC cable, Weasal conductor etc. Cost of labour, T&P carrier etc. required for proper completion of work as per RESPO Norms is included in the work.
311KV XLPE cable 3x185 mm2 (For Road Crossing)11KV XLPE cable 3x185 mm2 (For Road Crossing)
4LT ABC (3X120+1X70+1X16) SQMMLT ABC (3X120+1X70+1X16) SQMM
5ST Pole 11 Meter (For Make Double Pole)ST Pole 11 Meter (For Make Double Pole)
6ST Pole 9 METERST Pole 9 METER
711KV DISK INSULATOR WITH FITTING11KV DISK INSULATOR WITH FITTING
8Earthing CompleteEarthing Complete
9ACSR Dog ConductorACSR Dog Conductor
10LT XLPE Cable 3.5x400mm2LT XLPE Cable 3.5x400mm2
11LT XLPE Cable 3.5x240mm2LT XLPE Cable 3.5x240mm2
12LT XLPE Cable 1x120mm2LT XLPE Cable 1x120mm2
13V-TYPE CROSS ARMV-TYPE CROSS ARM
14Stay SetStay Set
15LT DISTRIBUTION BOX 3 PHASE WITH CLAMPLT DISTRIBUTION BOX 3 PHASE WITH CLAMP
16Cable Jointing Kit 3x185sq.mm. Outdoor typeCable Jointing Kit 3x185sq.mm. Outdoor type
1711KV PIN INSULATOR WITH PIN11KV PIN INSULATOR WITH PIN
1811KV TPMO SET11KV TPMO SET
1911KV DO FUSE SET11KV DO FUSE SET
20Supply, fixing and erection of following materials as per site requirement as per RESPO Norms:-Supply, fixing and erection of following materials as per site requirement as per RESPO Norms:-
21STONE PADSTONE PAD
22Cross Braccing AngleCross Braccing Angle
23Nut Bolt & WasherNut Bolt & Washer
24Barbed wireBarbed wire
25Danger BoardDanger Board
26PG ClampPG Clamp
27Number PlateNumber Plate
28Aluminium PaintAluminium Paint
29Rex Oxide PaintRex Oxide Paint
30Top ChannelTop Channel
31Dropper ChannelDropper Channel
32DP HOLDING CLAMPDP HOLDING CLAMP
33T/F BASE CHANNELT/F BASE CHANNEL
34Alumunium Lug 400MMSQAlumunium Lug 400MMSQ
35Alumunium Lug 240MMSQAlumunium Lug 240MMSQ
36Alumunium Lug 120MMSQAlumunium Lug 120MMSQ
37T-OFF CHANNELT-OFF CHANNEL
38PG CLAMPPG CLAMP
39F-BRACKETF-BRACKET
40WINDING WIRE 6 SWGWINDING WIRE 6 SWG
41SUSPENSION CLAMP WITH EYE HOOKSUSPENSION CLAMP WITH EYE HOOK
42LT PIERCING CONNECTOR FOR 120/50MMLT PIERCING CONNECTOR FOR 120/50MM
43DEAD END CLAMP WITH EYE HOOKDEAD END CLAMP WITH EYE HOOK
44Concreting of SupportConcreting of Support
45Concreting of StayConcreting of Stay
46Neutral & body earthing of Distribution Transformer by digging of pit upto water level and then inserting 1-¼” dia GI pipe of ‘A’ grade, conforming to the requirement of IS specification and then connecting the top of the inserted pipe and transformer body through GI strip of size 40x6 mm with the help of nut and bolt or through gas welding, as per direction of supervising engineer. It includes the cost of all material labour, T&P, carrier etc. required for proper completion of work. The aforesaid work shall be carried out as per RESSPO norms.Neutral & body earthing of Distribution Transformer by digging of pit upto water level and then inserting 1-¼” dia GI pipe of ‘A’ grade, conforming to the requirement of IS specification and then connecting the top of the inserted pipe and transformer body through GI strip of size 40x6 mm with the help of nut and bolt or through gas welding, as per direction of supervising engineer. It includes the cost of all material labour, T&P, carrier etc. required for proper completion of work. The aforesaid work shall be carried out as per RESSPO norms.
47Construction of plinth at various 11/0.4 KV Sub-station suitable for distribution transformer having size 2x2x1.5 Mtr. Work will include digging of foundation 2’ deep & brick work with Ist class bricks having cement and sand mortar of ratio 1:6 on all the walls, each of 9” thickness. The area inside the wall shall be duly filled by mud up to the height of appropriate level from ground level and shall be duly watered & rammed. Above the filling C.C. of ration 1:6:12 (Cement sand and brick ballast) giving 4” layer shall be provided. Above C.C. layer RCC layer having 4” thickness and with ratio 1:2:4 of cement sand and stone ballast shall be provided Re-enforcement shall be provided by providing net of (8 Nos. + 8 Nos.) M.S. rods of size 10 mm dia and each of 2M length in the middle of the top of C.C. layer. The plinth shall be plastered with 12mm thick plaster in ratio 1:4 at all sides. This work will include cost of labour, T&P and all material required for construction of plinth which shall be provided by the contractor as per RESSPO Norms.Construction of plinth at various 11/0.4 KV Sub-station suitable for distribution transformer having size 2x2x1.5 Mtr. Work will include digging of foundation 2’ deep & brick work with Ist class bricks having cement and sand mortar of ratio 1:6 on all the walls, each of 9” thickness. The area inside the wall shall be duly filled by mud up to the height of appropriate level from ground level and shall be duly watered & rammed. Above the filling C.C. of ration 1:6:12 (Cement sand and brick ballast) giving 4” layer shall be provided. Above C.C. layer RCC layer having 4” thickness and with ratio 1:2:4 of cement sand and stone ballast shall be provided Re-enforcement shall be provided by providing net of (8 Nos. + 8 Nos.) M.S. rods of size 10 mm dia and each of 2M length in the middle of the top of C.C. layer. The plinth shall be plastered with 12mm thick plaster in ratio 1:4 at all sides. This work will include cost of labour, T&P and all material required for construction of plinth which shall be provided by the contractor as per RESSPO Norms.
48Providing and fixing of welded wire mesh fencing around transformer plinth with M.S. Angle of size 35X35X6 mm. length and 1.20 Meters height, such panels shall be supported on M.S. Angle from of size 40X40X6 mm. having 04 Nos. corner supports of height 1.65 Meters including extended legs for grouting which will be used as a door for entry of the personnel or removal/shifting of transformer with welded hinges, sliding belt etc. for locking the arrangement as per drawing and specifications the fencing will be painted one coat of red oxide primer and then two coats of bus green synthetic enamel paint. The rates should be inclusive of all materials required for proper completion of above work (length of each fencing approx. 11 Meters)Providing and fixing of welded wire mesh fencing around transformer plinth with M.S. Angle of size 35X35X6 mm. length and 1.20 Meters height, such panels shall be supported on M.S. Angle from of size 40X40X6 mm. having 04 Nos. corner supports of height 1.65 Meters including extended legs for grouting which will be used as a door for entry of the personnel or removal/shifting of transformer with welded hinges, sliding belt etc. for locking the arrangement as per drawing and specifications the fencing will be painted one coat of red oxide primer and then two coats of bus green synthetic enamel paint. The rates should be inclusive of all materials required for proper completion of above work (length of each fencing approx. 11 Meters)
49Supply, fixing and erection of following materials as per site requirement as per RESPO Norms:-Supply, fixing and erection of following materials as per site requirement as per RESPO Norms:-
5011Mtr S.T. Pole (Scrap) (17+13 = 30 x175KG/Pole)11Mtr S.T. Pole (Scrap) (17+13 = 30 x175KG/Pole)
51Weasel Conductor (Scrap) (540Mtr. X 0.109KG/Meter)Weasel Conductor (Scrap) (540Mtr. X 0.109KG/Meter)
52Dog Conductor (Scrap) (2000Mtr. X 0.335KG/Meter)Dog Conductor (Scrap) (2000Mtr. X 0.335KG/Meter)
53Other Line Material scrap such as Cross Arm, Clamp, Angle, Channel, Pin etc. (17+13=30No. /8KG/Pole)Other Line Material scrap such as Cross Arm, Clamp, Angle, Channel, Pin etc. (17+13=30No. /8KG/Pole)
549Mtr. S.T. Pole Scrap (10No. X 123KG/Pole)9Mtr. S.T. Pole Scrap (10No. X 123KG/Pole)
55L.T. AB Cable scrap (440+50 = 490 x 1.17x 0.8 = 459KG)L.T. AB Cable scrap (440+50 = 490 x 1.17x 0.8 = 459KG)
56SHIFTING OF 33 kV LINESSHIFTING OF 33 kV LINES
57Safe carriage of following materials from Store centre or any other place to the respective site of work through the Kachha/Pacca road including loading, unloading at the respective ends and erection of same including the work of dragging as per site requirement, jumphering through XLPEcable, Weasal conductor etc. Cost of labour, T&P carrier etc. required for proper completion of work as per RESPO Norms is included in the work.Safe carriage of following materials from Store centre or any other place to the respective site of work through the Kachha/Pacca road including loading, unloading at the respective ends and erection of same including the work of dragging as per site requirement, jumphering through XLPEcable, Weasal conductor etc. Cost of labour, T&P carrier etc. required for proper completion of work as per RESPO Norms is included in the work.
58ST Pole 13 Meter (For Make Single Support / Double Pole)ST Pole 13 Meter (For Make Single Support / Double Pole)
5933KV Disc Insulator 70KN33KV Disc Insulator 70KN
6033KV Disc Fitting33KV Disc Fitting
6133KV Pin Insulator33KV Pin Insulator
6233KV Pin with Nut33KV Pin with Nut
63Earthing CompleteEarthing Complete
6433KV V-type Steel Cross Arm33KV V-type Steel Cross Arm
65Stay SetStay Set
66ACSR Dog ConductorACSR Dog Conductor
67Supply, fixing and erection of following materials as per site requirement as per RESPO Norms:-Supply, fixing and erection of following materials as per site requirement as per RESPO Norms:-
68G.I. Angle Iron 65x65x6mm. 4300mm Long Bracing with 04 No. ClampsG.I. Angle Iron 65x65x6mm. 4300mm Long Bracing with 04 No. Clamps
69G.I. Top Channel (125x65x6mm. 3200mm Long)G.I. Top Channel (125x65x6mm. 3200mm Long)
70Stone Pad 300x300x75mm.Stone Pad 300x300x75mm.
71Clmap with bolt, nut & washerClmap with bolt, nut & washer
72Number PlateNumber Plate
73Danger BoardDanger Board
74GI Barbed WireGI Barbed Wire
75Aluminum TapeAluminum Tape
76Aluminum PaintAluminum Paint
77Nut , Bolt & WasherNut , Bolt & Washer
78Red Oxide PaintRed Oxide Paint
79Guarding Angle (for Guarding of 33 Kv Lines)Guarding Angle (for Guarding of 33 Kv Lines)
80Guarding ClampGuarding Clamp
81GI Wire 8SWGGI Wire 8SWG
82GI Wire 6SWGGI Wire 6SWG
83Concreting of SupportConcreting of Support
84Concreting of StayConcreting of Stay
85Supply, fixing and erection of following materials as per site requirement as per RESPO Norms:-Supply, fixing and erection of following materials as per site requirement as per RESPO Norms:-
86Dog Conductor Scrap (8500 Mtr.)Dog Conductor Scrap (8500 Mtr.)
8713 Mtr. S.T. Pole Scrap (40 No.)13 Mtr. S.T. Pole Scrap (40 No.)
88Iron Scrap 102 No.Iron Scrap 102 No.

AI Tender Summary

OUR REF NO 58500960
AUTHORITY Government Departments
TENDER VALUE 25 Lakhs
LAST DATE 04-12-2026
Authority
Authority Name Uttar Pradesh Power Corporation Limited
Work Description Bids Are invited for Repair, Maintenance, And Installation Of Plant/ Systems/Equipments (Version 2) - In The Area Of Eutd-1 2 Aligarh; Electrical System Or Installation; On Semi Turnkey Basis - Shifting Of 11 Kv & L.T. Lines , Safe Carriage Of Following Materials From Store Centre Or Any Other Place To The Respective Site Of Work Through The Kachha/Pacca Road Including Loading, Unloading At The Respective Ends And Erection Of Same Including The Work Of Dragging As Per Site Requirement, Jumphering Of Transformer With 11 Kv Line Through Lt Abc Cable, Weasal Conductor Etc. Cost Of Labour, T&P Carrier Etc. Required For Proper Completion Of Work As Per Respo Norms Is Included In The Work. , 11Kv Xlpe Cable 3X185 Mm2 (For Road Crossing) , Lt Abc (3X120+1X70+1X16) Sqmm , St Pole 11 Meter (For Make Double Pole) , St Pole 9 Meter , 11Kv Disk Insulator With Fitting , Earthing Complete , Acsr Dog Conductor , Lt Xlpe Cable 3.5X400mm2 , Lt Xlpe Cable 3.5X240mm2 , Lt Xlpe Cable 1X120mm2 , V-Type Cross Arm , Stay Set , Lt Distribution Box 3 Phase With Clamp , Cable Jointing Kit 3X185sq.Mm. Outdoor Type , 11Kv Pin Insulator With Pin , 11Kv Tpmo Set , 11Kv Do Fuse Set , Supply, Fixing And Erection Of Following Materials As Per Site Requirement As Per Respo Norms:- , Stone Pad , Cross Braccing Angle , Nut Bolt & Washer , Barbed Wire , Danger Board , Pg Clamp , Number Plate , Aluminium Paint , Rex Oxide Paint , Top Channel , Dropper Channel , Dp Holding Clamp , T/F Base Channel , Alumunium Lug 400Mmsq , Alumunium Lug 240Mmsq , Alumunium Lug 120Mmsq , T-Off Channel , Pg Clamp , F-Bracket , Winding Wire 6 Swg , Suspension Clamp With Eye Hook , Lt Piercing Connector For 120/50Mm , Dead End Clamp With Eye Hook , Concreting Of Support , Concreting Of Stay , Neutral & Body Earthing Of Distribution Transformer By Digging Of Pit Upto Water Level And Then Inserting 1-¼ Dia Gi Pipe Of ‘A Grade, Conforming To The Requirement Of Is Specification And Then Connecting The Top Of The Inserted Pipe And Transformer Body Through Gi Strip Of Size 40X6 Mm With The Help Of Nut And Bolt Or Through Gas Welding, As Per Direction Of Supervising Engineer. It Includes The Cost Of All Material Labour, T&P, Carrier Etc. Required For Proper Completion Of Work. The Aforesaid Work Shall Be Carried Out As Per Resspo Norms. , Construction Of Plinth At Various 11/0.4 Kv Sub-Station Suitable For Distribution Transformer Having Size 2X2x1.5 Mtr. Work Will Include Digging Of Foundation 2 Deep & Brick Work With Ist Class Bricks Having Cement And Sand Mortar Of Ratio 1:6 On All The Walls, Each Of 9 Thickness. The Area Inside The Wall Shall Be Duly Filled By Mud Up To The Height Of Appropriate Level From Ground Level And Shall Be Duly Watered & Rammed. Above The Filling C.C. Of Ration 1:6:12 (Cement Sand And Brick Ballast) Giving 4 Layer Shall Be Provided. Above C.C. Layer Rcc Layer Having 4 Thickness And With Ratio 1:2:4 Of Cement Sand And Stone Ballast Shall Be Provided Re-Enforcement Shall Be Provided By Providing Net Of (8 Nos. + 8 Nos.) M.S. Rods Of Size 10 Mm Dia And Each Of 2M Length In The Middle Of The Top Of C.C. Layer. The Plinth Shall Be Plastered With 12Mm Thick Plaster In Ratio 1:4 At All Sides. This Work Will Include Cost Of Labour, T&P And All Material Required For Construction Of Plinth Which Shall Be Provided By The Contractor As Per Resspo Norms. , Providing And Fixing Of Welded Wire Mesh Fencing Around Transformer Plinth With M.S. Angle Of Size 35X35x6 Mm. Length And 1.20 Meters Height, Such Panels Shall Be Supported On M.S. Angle From Of Size 40X40x6 Mm. Having 04 Nos. Corner Supports Of Height 1.65 Meters Including Extended Legs For Grouting Which Will Be Used As A Door For Entry Of The Personnel Or Removal/Shifting Of Transformer With Welded Hinges, Sliding Belt Etc. For Locking The Arrangement As Per Drawing And Specifications The Fencing Will Be Painted One Coat Of Red Oxide Primer And Then Two Coats Of Bus Green Synthetic Enamel Paint. The Rates Should Be Inclusive Of All Materials Required For Proper Completion Of Above Work (Length Of Each Fencing Approx. 11 Meters) , Supply, Fixing And Erection Of Following Materials As Per Site Requirement As Per Respo Norms:- , 11Mtr S.T. Pole (Scrap) (17+13 = 30 X175kg/Pole) , Weasel Conductor (Scrap) (540Mtr. X 0.109Kg/Meter) , Dog Conductor (Scrap) (2000Mtr. X 0.335Kg/Meter) , Other Line Material Scrap Such As Cross Arm, Clamp, Angle, Channel, Pin Etc. (17+13=30No. /8Kg/Pole) , 9Mtr. S.T. Pole Scrap (10No. X 123Kg/Pole) , L.T. Ab Cable Scrap (440+50 = 490 X 1.17X 0.8 = 459Kg) , Shifting Of 33 Kv Lines , Safe Carriage Of Following Materials From Store Centre Or Any Other Place To The Respective Site Of Work Through The Kachha/Pacca Road Including Loading, Unloading At The Respective Ends And Erection Of Same Including The Work Of Dragging As Per Site Requirement, Jumphering Through Xlpecable, Weasal Conductor Etc. Cost Of Labour, T&P Carrier Etc. Required For Proper Completion Of Work As Per Respo Norms Is Included In The Work. , St Pole 13 Meter (For Make Single Support / Double Pole) , 33Kv Disc Insulator 70Kn , 33Kv Disc Fitting , 33Kv Pin Insulator , 33Kv Pin With Nut , Earthing Complete , 33Kv V-Type Steel Cross Arm , Stay Set , Acsr Dog Conductor , Supply, Fixing And Erection Of Following Materials As Per Site Requirement As Per Respo Norms:- , G.I. Angle Iron 65X65x6mm. 4300Mm Long Bracing With 04 No. Clamps , G.I. Top Channel (125X65x6mm. 3200Mm Long) , Stone Pad 300X300x75mm. , Clmap With Bolt, Nut & Washer , Number Plate , Danger Board , Gi Barbed Wire , Aluminum Tape , Aluminum Paint , Nut , Bolt & Washer , Red Oxide Paint , Guarding Angle (For Guarding Of 33 Kv Lines) , Guarding Clamp , Gi Wire 8Swg , Gi Wire 6Swg , Concreting Of Support , Concreting Of Stay , Supply, Fixing And Erection Of Following Materials As Per Site Requirement As Per Respo Norms:- , Dog Conductor Scrap (8500 Mtr.) , 13 Mtr. S.T. Pole Scrap (40 No.) , Iron Scrap 102 No.
Basic Detail
Tender No GEM/2026/B/8269087
Bidding Type Tender
Location
City Aligarh
State Uttar Pradesh
Key Dates
Publish Date 12 Nov 2026
Submission Date 04 Dec 2026
Open Date 05 Dec 2026
Finance
Tender Value 25 Lakhs
Tender Fee Ref. Documents
EMD 30000
Exemption Not Available
Document List
cb8fae54-d80a-46eb-a224-de64761f26fc.pdf
1794484079.xlsx
1794484093.pdf
1794484103.pdf
1794484742.pdf
Tender27_fb246591-a957-4ad6-bb561794484912445_BUYEREUDCALIGARH.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 12, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 04, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 16 days
Dec 05, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 17 days

Tender Documents

Download All (ZIP) ↓
pdf

cb8fae54-d80a-46eb-a224-de64761f26fc.pdf

xlsx

1794484079.xlsx

pdf

1794484093.pdf

pdf

1794484103.pdf

pdf

1794484742.pdf

pdf

Tender27_fb246591-a957-4ad6-bb561794484912445_BUYEREUDCALIGARH.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender