Tender For Addition/Alteration To Sncos Mess At Af Stn Dinjan Under Ge (Af) Mohanbari
Tender Value
43.50 Lakhs
Estimated cost
Bid Submission
24 Nov 2026
9 days left
EMD
87000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dibrugarh → Assam
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition/Alteration To Sncos Mess At Af Stn Dinjan Under Ge (Af) Mohanbari
BOQ
| Sl. No. | Item Description |
| 1 | Excavating in trenches n.exc 15 m wide and n.exc 1.5 m wide deep for foundations, etc or for shafts, wells, cesspits, manholes, pier holes etc n.exc 10 Sqm on plan and getting out in ordinary soft/loose soil complete all as specified and directed. |
| 2 | M&L for PCC (1:4:8) type D-2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed. |
| 3 | Returing, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cms in soft /loose soil complete all as specified and directed. |
| 4 | Removing excavated material n exc. 50m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed. |
| 5 | M&L for RCC 1:2:4 Nominal Mix type B1 (20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, columns, etc basement slabs, under-reamed piles and mass concrete complete all as specified and directed. |
| 6 | M&L for RCC 1:2:4 nominal mix type B1 (20mm graded stone aggregate) as in columns, pillars,piers, posts and struts complete all as specified and directed. |
| 7 | M&L for RCC types A1 1:1.5:3 nominal mix (20mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. |
| 8 | M&L for MS TMT bars 10 mm and over dia and cut to lenth, bent to shape required incl cranking bending spirally for hooping for clos hooking ends and binding with and incl MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 9 | M&L for TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed. |
| 10 | M&L for Formwork to flat sides of foundations , footings bases for columns, rafts and raft beams, sides and soffits (if any) of of foundation and plinth beams, and similar work vertical or to batter rough finished surfaces of concrete flat complete all as specified and directed. |
| 11 | M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, n.exc 200mm thick (Horizontal or sloping) fare finished complete all as specified and directed. |
| 12 | M&L for Formwork to sides of pillars,posts, struts, piers, columns and stanchions Square, rectangular on plan fare finished complete all as specified and directed. |
| 13 | M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete reilings, openings in concrete walls, floor and roofs exc 5 cm but in exc 10 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping ad similar work rough finished surface of concrete complete all as specified and directed. |
| 14 | M&L for brick work built in cement mortar 1:4 with well burnt bricks having crushing strength 75 Kg/ Sqcm straight or curved on plan exc 6 m mean radius etc complete all as specified and directed. |
| 15 | M&L for rendering 15mm thick cement plaster in cement mortar ( 1:4) on fair face of block/ brick or concrete surface with water proofing compound finished even and smooth without using extra cement complete all as specified and directed. |
| 16 | M&L for rendering/ plastering, 10 mm thick in cement mortar (1:6 )on fair faces of brick work or concrete surface of wall complete all as specified and directed. |
| 17 | S&F for 10-12mm thick high density PVC fluted decorative wall panelling of approved make, design, frame work using approved polymer-based construction adhesive and stainless steel/brass screws wherever required, including cutting, drilling, edge trimming, corner mouldings, joint finishing, sealant, all accessories, scaffolding, labour and making good distrubed surface complete as specified and directed. |
| 18 | S&F for factory made uPVC white colour Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed (3mm selected glass) & one no. wire meshpanels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed.Including taking down of old aluminum windows and cost of Glass and wiremesh used in it complete all as specified and directed.Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 19 | S&F for factory made uPVC white colour Single / Double leaf Door with hardwares, fittings and accessories complete all as specified and directed. Door shall be made of (big series) frame 116 x 45 mm and shutter/sash 70 x 35 mm having wall thickness of 2.3 ± 0.2 mm. Leaf shall be filled with uPVC multi-chambered panel / opaque panel / laminated glass / 6 mm toughened glass or as specified. Door height up to 2.40 m (or as per site requirement) and width as shown in drawings. Comprising of uPVC multi-chambered frame and sash, with inbuilt threshold / bottom track and weather drip, EPDM gasket, wool pile, uPVC glazing beads / panel beads of appropriate dimension, uPVC extruded interlocks and stiffeners. Shutter reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile). Profile of frame & sash shall be mitred cut and fusion welded at all corners, drilling of holes for fixing hardware's, lock and drainage of water etc.Hardware: Zinc alloy (white powder coated) door handle set with plate, multipoint locking system / mortise lock, zinc alloy tower bolts, door hinges (SS 304 / zinc alloy) heavy duty with SS pins, door stopper, necessary SS screws etc. All hardware shall be of approved quality.Fixing: G.I fasteners 100 x 8 mm size / chemical anchor bolts for fixing frame to finished wall. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality. Taking down of old doors (any material) and disposal, including cost of materials, labour, tools & plant, scaffolding and other sundries complete all as specified and directed.Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile & glass dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 20 | M&L for Providing and fixing 10mm thick plaster of paris in ceiling (Gypsumanhydrous) to flat surface over metal frame work and reinforced with G.I. wire mesh including metal frame Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre work incl GI wire mesh complete all as specified and directed. |
| 21 | All as per item No 20 above but but for raised moulding in cornices etc complete all as specified and directed. |
| 22 | S&F for aluminium louvered ventilators of section size 80mmx20mmx1.50mm including 5mm thick frosted glass fixed in half portion & adjustable type louvers in another half and stainless steel wire mesh fixed type on outside frame etc making to the jambs, including taking down old u/s ventilator and making good the wall for fixing new window complete all as specified and directed. |
| 23 | S&F in repair E-board 'Everest' or equivalent make 600x600x4mm thick white prelaminated sett embosed reinforced designed ceiling board tiles of approved texture at any height laid on Hot dipped Galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick GS sheet and of size 24x32x3000mm and spaced at 1200mm centers securely fixed to the structural soffits by approved hangers at 1200mm maximum centers. Hangers of GI wire 2mm dia to be fixed by approved rawl plug, level and justers and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall. Flush fitting of 1200mm long cross tee (with double stitching) to be interlocked between main runners at 600mm center to form 1200x600mm modules cross tee longer than 600mm to be supported independently. 600x600mm modules to be formed by fitting 600mm long cross Tee centrally between the 1200mm cross tee. Tee, Perimeter wall angle shall be of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour all as per manufacture instruction, including taking down wall/ceiling boards(fibre, pulp insulation etc) or inslutation boards any thickness incl fillets complete all as specified and directed. |
| 24 | Dismantling Brickwork or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins,arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles including removing of demolished materialfrom work site complete all as specified and directed. |
| 25 | Demolition of unreinforced cement concrete in ground floors and pavings n.exc 15 cm thickness (below or above ground level) complete all as specified and directed. |
| 26 | M&L for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 27 | M&L for 0.63 mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed. |
| 28 | S&F for tubular roof trusses (framed) trussed, purlins, crane gantries, rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS1161 1979 grade St.-240 complete all as specified and directed. |
| 29 | M&L for MS Plates (plain or chequered) of grade Fe-290 (Gde E-165) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed. |
| 30 | M&L for Cement concrete type type C-2, 1:3:6 (40mm graded stone aggregate) 50mm thick, as in plinth protection, pathway finished even and fair without using extra cement complete all as specified and directed. |
| 31 | M&L for broken stone as hardcore of gauge n.exc 63 mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 32 | Demolition of stone slabs and tiles of any description or thickness in floors aprons etc laid bedded and pointed in any mortar complete all as specified and directed. |
| 33 | M&L for 20mm thick granite (of any type) tiles machine cut on floor/window cill over cement screed 15mm thick in cement mortar 1:4 and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed. |
| 34 | M&L for Non Skid coloured ceramic tiles 7 to 8mm thick (Square/rectangular area of each tile exc 0.11 Sqm but n.exc 0.18 Sqm in floors etc over 25 mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate) 15mm screed bed in cement mortar 1:6 set and joined in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 35 | M&L for glazed ceramic coloured tiles of size 350X250X7mm/ 450X350X7 mm thick set and jointed in neat cement slurry and pointed in coloured cement as in vertical surfaces such as dado/skirting and facea of side bldg complete all as specified and directed. |
| 36 | M&L for rendring 5mm thick plaster in cement mortar (1:3) as in ceiling on fair faces of brick work or concrete surfaces including finishing even & smooth without using extra cement complete all as specified and directed. |
| 37 | M&L for three coats of white wash including preparingthe new/old concrete or plastered surface of ceiling complete all as specified and directed. |
| 38 | M&L for preparation of old plastered wall surfaces and applying 3mm thick wall care putty to get smooth and even surfaces as directed and applying two coats of oil bound distemper complete all as specified and directed. |
| 39 | M&L for preparation of New plastered wall surfaces and applying 3mm thick wall care putty to get smooth and even surfaces as directed and applying two coats of oil bound distemper complete all as specified and directed. |
| 40 | M&L for preparation of plastered or unplastered surfaces of new wall, cornices etc by brooming down or steel wire brushing, scrapping down, smoke soot, moulds, moos efflorescent and trading oil and greasy spots and applying two coat of cement base paint (white or tinned) complete all as specified and directed. |
| 41 | M&L for preparation of old decorated plastered or unplastered surfaces of old plastered wall, cornices etc by brooming down or steel wire brushing, scrapping down, smoke soot, moulds, moos efflorescent and trading oil and greasy spots complete removal of old plaster and applying two coat of cement base paint (white or tinned) complete all as specified and directed. |
| 42 | M&L for preparation new steel surfaces of any description exc 10 cm width or girth and applying two coats of Synthetic Enamle Paint over a coat of red oxide complete all as specified and directed. |
| 43 | M&L for preparing newly wood or wood based surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 44 | S&F for solid PVC door frames of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed. |
| 45 | S&F for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solovent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded sealed to the stiles and rail with suitable PVC sheet beading and jointed together with solvent cement supply and fixing in the frame at site as per specification and drawing and complete all as specified and directed. |
| 46 | S&F for 25mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides both face is covered with deco rative face veneer with lipping/frame to match as in cupboard door shutters complete all as specified and directed. |
| 47 | S&F for Pressed steel frames made of 1.25 mm thick MS Sheet size 125x60mm for doors, ventilator with double rebates including necessary fixing lugs, hinges, lock strike plate etc and incl providing PCC 1:2:4 type B1 (using 20mm graded stone agg) to fill the frame & making good complete all as specified and directed. |
| 48 | M&L for 35 mm thick factory made 1st class hard wood glazed/gazsed and skelton door shutter, factory made, open rebated and prepared to receive glass/guage etc. (without sash bar) edge of frames plain, chamfered or rounded, fitted with cut & mitred beads for securing glass/guage etc size of member as specified in SSR Part I Section 8 clause 8.24(a) and fixed to chowkat complete all as specified and directed. |
| 49 | S&F for Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm complete all as specified and directed. |
| 50 | S&F for Aluminium, anodised, handles 150 mm of extruded section complete all as specified and directed. |
| 51 | S&F for Aluminium, anodised, tower bolt, Length of bolt in mm 150 mm of extruded section complete all as specified and directed. |
| 52 | S&F for 100 mm long butt hinges, extruded alminium alloy with galavanised mild steel hinge pin, anodised and fixed , type C-21 complete all as specified and directed. |
| 53 | S&F in repair vitreous china wash basin white flat back size 580x450 mm excluding,pillar tap, 32 mm dia CP waste fitting and PVC waste pipe 610 mm long and brackets complete all as specified and directed. |
| 54 | S&F for Vitreous china squatting pan of pattern, long pan, 'Orissa pattern', size 580 x 440 mm white with integral foot rests (excl flushing cistern and flush pipe) but including provision of lime concrete complete all as specified and directed. |
| 55 | S&F for PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle (incl brackets & flush pipe PVC 32 mm dia) capacity of 10 Litres complete all as specified and directed. |
| 56 | S&F for 3 layered rotational moulded polyethylene water storage tanks capacity 1000 lit in white colour (cylindrical vertical with closed top) hoisted and fixed in position including dismantling and removing of old tank complete all as specified and directed. |
| 57 | S&F in repair 20mm dia ball brass valves high pressure with polythene float valve & fly nut screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 58 | S&F for steel water tubing 15 mm bore medium grade galvanised with all fittings (ISI marked) fixed complete to walls, ceiling or laid in floors complete all as specified and directed. |
| 59 | S&F for steel water tubing 20 mm bore medium grade galvanised with all fittings (ISI marked) fixed complete to walls, ceiling or laid in floors complete all as specified and directed. |
| 60 | S&F for Bib tap 15 mm bore, Brass CP, fancy type (long shank), with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 61 | S&F in repair Pillar taps chromium plated cast copper alloy with capstan heads screwed down high pressure with or without lettered hot or cold With long screwed shanks and fly nutsscrewed for iron pipes 15mm bore dia complete all as specified and directed. |
| 62 | S&F for brass CP shower rose 125mm size with swivel joint incl fixing to steel pipe fixed in repairs complete all as specified and directed. |
| 63 | S&F for Looking mirror 600mm x 450 mm beveled edge of selected quality glass fixed with PVC moulded frame, fixed to plugs with chromium plated brass screws all as spd and directed by EIC complete all as specified and directed. |
| 64 | S&F for towel rail 450 mm long of PTMT fixed with and including chromium plated brass screw and wooden / plastics cleats (min wt 170 gms) complete all as specified and directed. |
| 65 | S&F in repair MS Curtain rod 20mm dia covered with coloured PVC layer with and including decorative Knob and brackets complete all as specified and directed. |
| 66 | S&F for health Faucet cera Model-F 8030105AB (ABS) with 1 meter SS Braided connection pipe or techno commercial equvalent complete all as specified and directed. |
| 67 | S&F for Stop valve (ISI Marked), cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore and fixed complete all as specified and directed. |
| 68 | S&F for 15 mm dia PVC connection pipe 450 mm long with two nuts fly nuts complete all as specified and directed. |
| 69 | S&F for PVC(SWR) sewage pipe 110 dia single socket in any length with rubber ring joints fixed to wall or floor complete all as specified and directed. |
| 70 | S&F for PVC(SWR) sewage pipe 75 dia single socket in any length with rubber ring joints fixed to wall or floor complete all as specified and directed. |
| 71 | S&F for 100/110mm bore PVC (SWR) bends any radius, duck's foot or heel rest complete all as specified and directed. |
| 72 | S&F for 75mm bore PVC (SWR) bends any radiu, duck's foot or heel restcomplete complete all as specified and directed. |
| 73 | S&F for 100/110mm bore PVC (SWR) reducers complete all as specified and directed. |
| 74 | S&F for 110mm PVC (SWR) `P' trap complete all as specified and directed. |
| 75 | S&F for PVC (SWR) branch piece, single (single Y) 110 mm dia equal or unequal complete all as specified and directed. |
| 76 | S&F for 110mm bore PVC (SWR) junction single (Single T) equal or unequal complete all as specified and directed. |
| 77 | S&F for PVC (SWR) cowl suitable for pipes of 75 mm bore complete all as specified and directed. |
| 78 | S&F for Stack clamps out of 75 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75mm bore pipe complete all as specified and directed. |
| 79 | S&F for PVC (SWR) floor trap, Diameter of outlet in 75 mm plain with grating including jointing with solvent cement complete all as specified and directed. |
| 80 | S&F in repair kitchen sink with drainage board made out of 1mm thick stainless steel with plugs, washers & wastes including CI cantilever bracket & connection union to pipe over all size 915mmx460mm & bowl size 410 x330x160mm complete all as specified and as directed. |
| 81 | M&L for plain, galvanised mild steel sheeting in ridges hips valley gutters drip and straight flashing (length and girth as fixed) by using 1.0mm thick sheet grade of zinc coating @275 Gms/Sqm both sides and welded or soldered joints including necessary fittings and plain or corrugated steel sheeting any gauge thickness (including Nainital or similar pattern) as in roof valley gutters complete all as specified and directed. |
| 82 | M&L for Machine cut cudappa stone slab 20-25mm thick as in steps, jambs, pillars, window- cills, cooking platforms, and like over 15mm thick cement screed base in cement mortar (1:4) and jointed in grey cement slurry mixed with pigment to match with shade of slab of existing cill/cooking plat form complete all as specified and directed. |
| 83 | M&L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed. |
| 84 | M&L for Machine cut Kota stone slab 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, over and including 10 mm thick screed bed in cement mortar (1:6) as in flooring, kitchen platform, steps etc complete all as specified and as directed. |
| 85 | Taking down carefully aluminium/ copper point wiring (light, fan, socket, power point) including batten, conduit and fittings such as switches, ceiling rose, sockets, brackets, light fittings, switch board etc removing, making good distrubed surfaces of wall, floor, ceiling etc complete all as specified and directed. |
| 86 | M&L for point wiring with 1.5 sqmm cable PVC unsheathed and insulated copper multistranded conductor (FRLS) 1100 Volts grade cable (red colour cable to be used for phase connection and black colour cable to be used for neutral connection) including PVC concealed conduit medium grade with all accessories including 1.5 sqmm copper multistrand conductor (FRLS) 1100 Volts grade unsheathed PVC insulated (green colour) continuity earth wire connected to common earth dolly and steel terminal box suitable for Modular switch and sockets ,fan regulator etc incl cutting chases pinning in, for concealed conduit wiring and making goods of disturbed surface not exc 15 cm girth complete all as specified and directed for the following:- Note: Cutting and chasing deemed to be included in coated rate. |
| 87 | Light/ Fan/ Bell point controlled by one switch |
| 88 | 5 amp socket on same boared |
| 89 | 5 Amp switch socket on Independent Board. |
| 90 | All as per item No 86 here in before but 2.5 sqmm P.V.C insulated unsheathed cable with stranded copper conductor for 6 pin, 6/16 Amp switch socket combination on independent board complete all as specified and directed. |
| 91 | S&F for modular flush Box 6 module complete all as specified and directed. |
| 92 | S&F for Modula cover plate with frame 6 module complete all as specified and directed. |
| 93 | S&F for modular flush Box 3 module (For 5A /15A indepandant sockets) complete all as specified and directed. |
| 94 | S&F for Modula cover plate with frame 3 module complete all as specified and directed. |
| 95 | S&F for Socket of indo american universal type, 6A - 2/3 pin combined 2 module, 230 volt, multipurpose complete all as specified and directed. |
| 96 | S&F for Socket of indo american universal type 6A/16A - 2/3 pin combined 2 module, 230 volt, multipurpose complete all as specified and directed. |
| 97 | S&F for Modular switch 1 way 6A, 1 module single pole complete all as specified and directed. |
| 98 | S&F for Modular switch 1 way 16A, 1 module single pole complete all as specified and directed. |
| 99 | S&F in ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified and directed. |
| 100 | S&F in Modular fan regulator , stap type, 220/240 volts complete all as specified and directed. |
| 101 | S&F in repair of factory made sheet metal enclosure for DBs double door, SPN, 240 volt, 8 Way, IP-42 protection with bus bar, neutral link, earth link complete all as specified and directed. |
| 102 | S&F for 240V, 10KA 'C' curve miniature circuit breaker (MCB) SP 10 to 32 Amp current carrying capacity complete with connection testing complete all as specified and directed. |
| 103 | S&F for 240V, 10KA 'C' curve miniature circuit breaker (MCB) SPN 63 Amp current carrying capacity complete with connection testing complete all as specified and directed. |
| 104 | S&F for exhaust fan, heavy deuty, steel body AC single Phase. 230V of size 300m sweep 1400RPM, and min air delivery 1850m3/h with, blades, and frame and louvers complete all as specified and directed. |
| 105 | S&F for ceiling fans complete with blades, anti suicide down rods 12 inch length (off white color), and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed. |
| 106 | S&F for wall mounted fan, PVC body AC single Phase. 230V of size 400m sweep with, blades, and frame with provision of ossilation of 60 degree and provision of pull cord for speed and ossilation control complete all as specified and directed. |
| 107 | M&L for sub main wiring with 2 run of FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.0 sqmm alongwith one run of FRLS PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.0 sqmm as earth continuity conductor drawn through & including PVC casing-caping medium grade complete all as specified and directed. |
| 108 | S&F for ultra slim LED 20 Watt, 230 volts, 50 Hz, 4 feet,inverter type lighting fixture with extruded polycarbonate lighting fixture, environmental friendly, energy efficient ready to use pack including lamp complete all as specified and directed. Make : Havells, Cat Part No LXEXASP7IN1W020. |
| 109 | S&F for recessed mounted 36 Watt (clear white) LED panel light 2x2 feet, ultra slim design, 230 volts, 50 Hz with CRCA sheet housing precoated white colour and high quality diffuser for uniform light and high efficiency with separate replaceable electronic driver including lamp complete all as specified and directed. Make : Crompton, Cat Part No CCB-122-36-57-SL-MWS-DP-NWH. |
| 110 | S&F for recessed mounted LED light of round type, minimum 1200 Lumen (12Watt ) with all accessories internally prewired and including connecting up with twisted copper conductor cable of suitable size complete all as specified and directed. Make : Crompton, Cat Part No CDR-205-12-57-SL-NWH. |
| 111 | S&F for Wall mounted LED light of type, minimum 1200 Lumen (12Watt ) with all accessories internally prewired and including connecting up with twisted copper conductor cable of suitable size complete all as specified and directed. Please Enable Macros to View BoQ information |
| 112 | S&F for Wall mounted LED light of type, minimum 1200 Lumen (12Watt ) with all accessories internally prewired and including connecting up with twisted copper conductor cable of suitable size complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 11, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 24, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysNov 25, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 10 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender