Tender For Replacement Of Paver Block, Kerb Stone & Other Miscellaneous Civil & Allied Works Infront Of C Block Entrance, Amd Office Complex
Tender Value
12.18 Lakhs
Estimated cost
Bid Submission
23 Nov 2026
8 days left
EMD
24370
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Hyderabad → Telangana
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Replacement Of Paver Block, Kerb Stone & Other Miscellaneous Civil & Allied Works Infront Of C Block Entrance, Amd Office Complex
BOQ
| Sl. No. | Item Description |
| 1 | 1.0 Contractor shall inspect the site to acquaint with the site conditions as well as security conditions and upload site inspection report issued by the departmental officer with seal and signature which is mandatory document without which tender will not be considered for evaluation.2.0 All the dismantled/ demolished materials shall be dumped at one place as decided by the department within the lead of 50.0mtr. 3.0 All the samples of materials which are to be incorporated in the work shall be got approved by the Engineer -In- charge well in advance and necessary testing of materials shall be carried out by the contractor as per the instruction of E-I-C. Charges towards the testing shall be borne bt the contractor itself.4.0 It is the responsibility of the contractor to handover the dismantled items to Dept. At site. Contractor shall be held responsible for any shortage/ missing of dismantled items until handing over the same to dept. stores.5.0 Contractor shall quote rates for all items after considering cost of materials and labour components and all such conditions leads, lifts, safety precautions, security restrictions that are necessary for satisfactory completion of work as per instructions and site conditions. Security regulations shall be followed.6.0 The rates quoted shall include cost of all tools and tackles, manpower including wages, liveries, all wastages and GST, water charges, Labour cess, seignorage charges etc. as applicable but exclusive of EPF and ESI. EPF and ESI are reimbursable as per relevant clause on production of proof of payment as per CPWD norms. |
| 2 | Excavation work of ordinary rock by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m as per specification & direction of E-I-C. |
| 3 | Demolishing cement concrete nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. |
| 4 | Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge. |
| 5 | Taking out existing kerb stones of all types from footpath/ central verge, including removal of mortar etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge. |
| 6 | Dismantling Aluminium Composite Panel /aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineerin-charge. |
| 7 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved |
| 8 | Providing and laying in position 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural resources : 4 graded stone aggregate 20 mm nominal size derived from natural resources)cement concrete of specified grade excluding the cost of centering and shuttering - All work up to up to floor five levelas per specification and direction of E-I-C. |
| 9 | Providing and laying Outdoor parking Polished heavy duty Vitrified tiles of 600X600mm size, thickness 12mm, colour and pattern as decided by E-I-C. Tiles shall be laid over a 20 mm thick cement mortar bed (1:4) with spacer of min.3mm, maintaining proper line, level and uniform joints Joints shall be filled with epoxy grouting, and the finished surface shall be cured for at least seven days. The completed work shall be even, durable, anti-skid, free from cracks or defects, and finished to the satisfaction of the Engineer-in-Charge. |
| 10 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). |
| 11 | Brick work with Cement mortar 1:4 (1 cement : 4 coarse sand) common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes. |
| 12 | Cement plastering 12mm thick for internal walls, ceilings, at all floors and locations with cement mortar 1:4 finished smooth over brick/concrete surfaces including hacking of concrete surfaces, raking out of brick joints, curing complete as per specifications and directions of Engineer-in-charge. |
| 13 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 14 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 15 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content with water thinnable cement primer on wall surface having VOC content less than 50 grams/litre. |
| 16 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.Two coats. |
| 17 | Painting on G.S. sheet/ MS with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : |
| 18 | Varnishing with varnish of approved brand and manufacture :Two or more coats of glue sizing with copal varnish over anunder coat of flatting varnish. |
| 19 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion: Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 20 | Designing, providing and fixing of 4 mm thick approved make and shade Aluminium Composite Metal Panel of approved make cladding at different locations including soffits of over-hangs but excluding aluminium frame work with grids filled in with weather silicon sealant as per the drawings. The ACM panel composition shall be of 0.5 mm thick PVDF coated aluminium sheet + 3 mm thick low density polyethelene virgin resin core + 0.5 mm thick polyester (PVDF) coated Aluminium sheet all complete as per approved shop drawings and specification (Aluminium frame work will be paid under reelevant item).Note : ACMP shall be measured to the actual visible area of the ACP sheet including silicon joints as fixed on site. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 11, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 23, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 8 daysNov 25, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 10 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender