Tender For Various Development And Repair Works At The Park Located On Aman Street, Jagannathpuri, Ambe Nagar Park, And The Park Near The Community Centre In Ward No. 19, Vidyadhar Nagar Zone.
Tender Value
49.25 Lakhs
Estimated cost
Bid Submission
17 Nov 2026
6 days left
EMD
98500
Bank guarantee accepted
Document Fee
590
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jaipur → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Various Development And Repair Works At The Park Located On Aman Street, Jagannathpuri, Ambe Nagar Park, And The Park Near The Community Centre In Ward No. 19, Vidyadhar Nagar Zone.
BOQ
| Sl. No. | Item Description |
| 1 | (4.10.1.1) Earth work in excavation in foundation, trenches etc. including dressing of sides and ramming of bottoms, including getting out the excavated material, refilling after laying pipe/ foundation and disposal of surplus excavated material at a lead upto 50m suitable site as per direction of Engineer for following depths, below natural ground / Road top level.In all types soils/ saturated soil such as moorum, sand, sandy silt, clay, black cotton soil, kankar, etc.Depth upto 1.5 m |
| 2 | (4.1) Dressing of earth work in surface excavation including cutting and filling upto 30cm depth including disposal of excavated earth upto 50m and lift upto 1.5 m. |
| 3 | (1.1.1) Carriage of Materials by mechanical transport including\ loading, unloading and\ stacking ::Earth upto 10 km |
| 4 | (25.1.1) Random rubble masonry with hard stone in foundation and plinth :Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 5 | (24.5.2) Brick work with FPS bricks of class designation 75 in superstructure above plinth level upto two stories in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 6 | (32.2.2) Cement plastering including T&P, scaffolding, material and complete labour, including cost of water, curing, racking of joints etc. with 15 mm cement plaster on the rough side of single or half brick wall of mix : including Providing /mixing of synthetic fibers compulsorily complying with IS 16481:2022 of 06 mm/12 mm length to be mixed @ 0.25% by weight of Cement i.e. 125 gms per 50 kg Cement up to 900 gms per cum of Concrete/ mortar 1:6 (1 cement : 6 fine/ coarse sand) |
| 7 | (32.15) Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete |
| 8 | (32.35.1) Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20kg/ 10 sqm). |
| 9 | (9.3) Providing and laying lean cement concrete 1:4:8 in Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in concrete mixer, laid manually, compacted with surface vibrator, finishing and curing complete as per clause 601, 112 of MoRT&H specification including all material, labour, machinery, lighting, guarding and maintenance of diversion. |
| 10 | (30.20.4) Chequered terrazzo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) :Ordinary cement without any pigment |
| 11 | (9.11) Providing and fixing of 60mm thick precast cement concrete interlocking paver block casted with rubber moulds in approved reflective colour and design having minimum compressive strength of 300 kg/ sq cm. The CC paving blocks be laid on average 50mm thick bed of coarse sand and the joint is to be filled with fine sand. Laying procedure on compacted sub-base as defined. Complete job is to be executed as per the instruction of Engineer in-charge. The rates to be inclusive of all lead & Lifts etc. complete as per specifications. |
| 12 | (10.1) Providing and fixing precast cement concrete M-20 grade (Using mechanical Concrete Mixer) kerb stone top and bottom width 115 and 165 mm respectively, 250 mm high on 150 mm thick PCC M-10 grade foundation as per design, including fixing at site as per clause 408 of MoRT&H Specification including all material, labour, machinery, lighting, guarding and maintenance of diversion. |
| 13 | (21.1.2) Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level :1:1½:3 (1 Cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size). |
| 14 | (32.50.1) Supplying, erecting and fixing in position specified precast RCC bench made of RCC grade M-30 consisting of 2 Nos. “L” shaped base support of thickness 100 mm back height 1000mm, front height 450 mm, base width 420mm and 5 Nos. RCC planks of size of 1500x100 x 50 mm and 1 Nos RCC planks of 150x200x50mm including joining all parts with galvanised nuts and bolts of suitable size. All bolts to be sealed after assembly with nice finish and appearance and level complete in all respect as per direction of engineer in-charge. Every bench should have a manufacturer’s logo of appropriate size Engraved at suitable place. |
| 15 | (32.50.1) Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work |
| 16 | (29.26.2) Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 17 | CROSS TRAINERProviding and fixing of Cross trainer of size not less than 1140mm (Length) x 625mm (Width) x 1750mm. (Height), to enhance the mobility of upper and lower limbs and improve the flexibility of joints. The main structure frame shall be made from G.I. pipe minimum of 80NB “C” class welded with M.S. round base plate at least Ø250 mm & 10mm thick. The Handle Frame shall be made up of at least 25NB “C” Class G.I. Pipe. The footrests shall be made from LLDPE/Aluminum casting material of size not less than 130 mm X 310mmX5mm thickness and mounted on M.S. Plate of Size 130mmx310mmx3mm thick. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders of Ackzonoble/ Berger/ Nerolac Paints with 60 to 70 Micron thicknesses complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in- charge to fulfill the functional requirement. |
| 18 | SEATED PULLERProviding and fixing of Seated Puller of size not less than 2400mm (Length) x 800mm (Width) x 2000mm. (Height), to enhance the strength of upper limbs and the muscles in chest and back and promote cardio-pulmonary function. The main structure frame shall be made from G.I. pipe minimum of 100NB “C” class welded with M.S. round base plate at least Ø250 mm & 10mm thick. The handle frame shall be minimum of 32NB “C” class G.I. pipe. The seat frame minimum of 50NB “C” class G.I. pipe, Closing Caps shall be made up of LLDPE/high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts & bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders of Ackzonoble/ Berger/ Nerolac Paints with 60 to 70 micron thickness complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fulfill the functional requirement. |
| 19 | CHEST PRESSProviding and fixing of Chest Press of size not less than 2200mm (Length) x 800mm (Width) x 2000mm. (Height), to enhance the strength of upper limbs and the muscles in chest & back and promote cardio pulmonary function. The main structure frame shall be made from G.I. pipe minimum of 100NB “C” class welded with M.S. round base plate at least Ø250 mm & 10mm thick. The handle frame shall be made up from at least 32NB “C” class G.I. pipe. The seats and Back rests to be fitted on the outer frames shall be made up of M.S. Sheet of size not less than 330mm X 300 mmX2mm thickness. Closing Caps shall be made up of LLDPE/high quality Fiber reinforced Plastic material. High tensile steel with galvanized nuts & bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble/ Berger/ Nerolac Paints with 60 to 70 micron thickness complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fulfill the functional requirement. |
| 20 | Providing and fixing of Double Twister Standing of size not less than 1500mm (Length) x 600mm (Width) x 1300mm. (Height), to enhance flexibility of waist. The main structure frame shall be made from G.I. pipe minimum of 100NB “C” class welded with M.S. round base plate at least Ø250 mm & 10mm thick. The handle frame is minimum of 25NB shall be made from “C” class G.I. pipe. The Twister plate to be fitted on the bottom frame shall be made up of M.S. Round Plate of minimum size Ø250mm and 10mm thick. Closing Caps shall be made up of high quality LLDPE/Fiber reinforced Plastic material. High tensile steel with galvanized nuts and bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders from Ackzonoble/ Berger/ Nerolac Paints with 60 to 70 micron thickness complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in- charge to fulfill the functional requirement. |
| 21 | SKY WALKER : Area : - 1.72 Mtr x 0.63 Mtr Safe Area :- 2.54 Mtr x 1 MtrProviding and fixing sky walker made from \\"B\\" class G.I. pipe. the main frame pipe is Ǿ 80mm made from \\"C\\" class G.I. pipe. the outer ring of sky walker is Ǿ 32mm made from \\"C\\" class G.I. pipe. for connecting the handle frame to main pipe Ǿ 60mm \\"C\\" class G.I. pipe is used. the bottom support of M.S. round plate of Ǿ 250mm x 10mm thickness is welded at bottom. the leg movement frame is of 50x50mmx2mm thick CRC square pipe. the handle frame is of Ǿ 40mm made from \\"C\\" class G.I. pipe. the foundation used for fixing is 80x40mmx3mm thickness C-channel. the footrests is made from aluminum casting material, its sizes are 130x310x5mm. closing caps made from top quality FRP material with 2mm thickness & plastic cap are used. the pins used are made up of Ǿ 25mm bright bar. the bearings used are \\"6205zz\\" & \\"6203zz\\" permanent lubricated sealed bering of reputed make (SKF/FAG). high tensile steel with galvanized nut bolts are used for assembly. the serclips used for assembly are of Ǿ 25mm. the powder coat is done by poly urethane & epoxy powder with 60 to 70 micron thickness |
| 22 | SURFING BOARDProviding and fixing of Surfing Board of size not less than 1150mm (Length) x 900mm (Width) x 1400mm (Height), to build up the muscle groups of the waist, enhance the body coordination and flexibility. The main structure frame shall be made from G.I. pipe minimum of 100NB “C” class welded with M.S. round base plate at least Ø250 mm & 10mm thick. The footrests shall be made from high quality LLDPE/fiber reinforced plastic material. High tensile steel with galvanized nut bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powder of Ackzonoble/ Berger/ Nerolac with minimum 60 to 70 micron thickness complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fulfill the functional requirement. |
| 23 | STANDING SEATING TWISTERProviding and fixing of Seating & Standing Twister of size not less than 1700mm (Length) x 540mm (Width) x 1250mm. (Height), to enhance flexibility of waist. Suitable for people of different ages except children. The main structure frame shall be made from G.I. pipe minimum of 100NB “C” class welded with M.S. round base plate at least Ø250 mm & 10mm thick. The bottom frame of the Seating & Standing twister be at least of 32 NB, 50 NB, and 25 NB shall be made from “C” class G.I. pipe. The handle frame of Seating & Standing twister of minimum 25 NB & Foot resting frame of seating side shall be made from “C” class G.I. pipe minimum of 25mm NB. The Twister plate to be fitted on the bottom frame shall be made up of M.S. Round Plate of minimum size 250 mm diameters and 10mm thickness. Closing Caps shall be made up of high quality LLDPE/Fiber reinforced Plastic material. High tensile steel with galvanized nuts & bolts shall be used for assembly. The powder coating shall be done by Pure Polyester powder of Ackzonoble/ Berger/ Nerolac Paint with 60 to 70 micron thickness complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in- charge to fulfill the functional requirement. |
| 24 | PUSH UP BARSProviding and fixing of Push Up Bars of size not less than 1800mm (Length) x 680mm (Width) x 1550mm. (Height), To enhance the strength and stamina of the body. The main structure frame shall be made from G.I. pipe minimum of 100NB “C” class welded with M.S. round base plate at least Ø250 mm & 10mm thick. The handle frame minimum of 25 NB shall be made from “C” Class G.I. pipe. Closing Caps shall be made up of high quality LLDPE/Fiber reinforced Plastic material. High tensile steel with galvanized nuts & bolts shall be used for assembly. The powder coating shall be done with Pure Polyester powders of Ackzonoble/ Berger/ Nerolac Paints with 60 to 70 micron thickness complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fulfill the functional requirement. |
| 25 | SIT UP BOARD DOUBLEProviding and fixing of Sit up Board double of size not less than 1580mm (Length) x 1400mm (Width) x 680mm (Height), to enhance the flexibility of whole body. The main structure frame shall be made from G.I. pipe minimum of 100NB “C” class welded with M.S. round base plate at least Ø250 mm & 10mm thick. The remaining frame of the sit up board minimum of 32mm NB shall be made from “C” class GI pipe. The powder coating shall be done with Pure Polyester powder Ackzonoble/ Berger/ Nerolac Paints with 60 to 70 micron thickness complete in all respect including fixing the M.S. holdfast in cement concrete to hold the whole structure, under the directions of Engineer-in-charge to fulfill the functional requirement. |
| 26 | LEG PRESS : Area :- 0.40x1.77 MtrSafe Area :- Providing and the center pThe bottom support thickness is welded the remaining outer frame pipe. the foundation used for Ǿ 80mm made from \\"C\\" c & 10 mm thickness, 25mmx25mm. to join the c 3mm thicness is used. the seats are size 330mmx3mm and size 250mmx 200mm. the footrests is made 130mmx311.77 mtr.-1x2.38mtr. fixing leg press made from \\"B\\" class G.I. p pipe is of Ǿ 115mm made from \\"C\\" class G.I. of M.S. round plate of Ǿ 250mm & at bottom. is of Ǿ 40mm made from \\"C\\" class G.I. foundation fixing is consist of three equal class G.I. pipe, M.S. round p x 3mm M.S. angle. centre pipe & outer frame seamless pipe of thickness fitted on the outer frame is made up of FRP material of 300mm of thickness 3mm & M.S. plate of is used to support it. from aluminum casting material, i 10mm & 5mm thickness. pipe, made pipe and 250mm, 10mm items i.e. plate of Ǿ 250mm angle. Ǿ 120mm & thickness 5 support its sizes are the frame of footrests consists of Ǿ 32mm made from \\"C\\" class G.I. pipe. closing caps made from top quality FRP material which is of 2 mm thickness. the inner bushes is made from seamless pipe, its diameter is 60mm & 5mm thickness. the pins used in are made up of Ǿ 25 mm hardened bright bar, the bearings used are of \\"6205zz\\" permanent lubricated sealed bearing of reputed make (FAG/SKF). the handles used are of rubber grip. high tensile steel with galvanized nut bolts are used for assembly. the serclips used for assembly are of Ǿ 25 mm. the powder coat is done by poly urethane & exoxy powder with 60-to-70-micron thickness. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 07, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysNov 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender