Rural Development Local Bodies Closing in 4 days TDR #58483239

Tender For Chalavara Grama Panchayath ,Vendor Selection For Supply Of Various Mterials For Vb-G Ram (G)

Issued by Local Bodies · Palakkad, Kerala
Tender Value
40 Lakhs
Estimated cost
Bid Submission
19 Nov 2026
4 days left
EMD
50000
Bank guarantee accepted
Document Fee
2500
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Palakkad → Kerala
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender for Chalavara Grama Panchayath ,Vendor Selection For Supply Of Various Mterials For Vb-G Ram (G) , Quarry Waste , Stone Aggregate(Single Size): 40 Mm Nominal Size , Stone Aggregate(Single Size):20 Mm Nominal Size , Stone Aggregate(Single Size): 10 Mm Nominal Size , Stone Aggregate(Single Size): 06 Mm Nominal Size , Fine Sand (Zone Iv) , Coarse Sand (Zone Iii) , Gravel 5Mm To 10Mm , Stone For Masonry Work , Portland Cement , M.S. Tube 40 Mm Dia , Mild Steel Tubes Hot Finished Welded Type , Galvanised Steel Bolts & Nuts 6 Mm Dia And 25 Mm Long Round Head With Slots , Galvanised Steel J Or L Hooks 8 Mm Dia , G.I Limpet Washer , Bitumen Washer , Mild Steel Round Bar 12 Mm Dia And Below , Mild Steel Round Bar Above 12 Mm Dia , Mild Steel Sheets With Bolts And Nuts To Rest On Pintels , Iron Pintels Including Weldded Pin , Mild Steel Sheets For Tanks , Mild Steel Hooks , Mild Steel Plate , Mild Steel Tubes Electric Resistant Or Induction Butt Welded , Welding By Electric Plant , Wire Nails , Bright Finished Or Black Enameled Mild Steel Butt Hinges 100X58x1.90 Mm , Bright Finished Or Black Enameled Mild Steel Screws 40 Mm , Bright Finished Or Black Enameled Mild Steel Screws 20 Mm , Powder Coated M.S. Butt Hinges 100 Mm X58 Mm X 1.9 Mm , Flats Up To 10 Mm In Thickness , Galvanised Wire Mesh Of Average Width Of Aperture 1.4 And Nominal Dia.Of Wire 0.63 Mm , G.I Trafford Profile Sheet 0.35Mm Thick , Precoated Aluminium Traffored Sheet 0.450 Mm Thick , Structural Steel Such As Tees,Angles,Channels And Rs Joists , Stainless Steel Screws 50 Mm , Red Oxide Zinc Chromate Primer , Precoated Galvanised Steel Plain Ridges , Stainless Steel (Grade - 304) Hollow Section Round/Square Tubes , Stainless Steel Bolts /Square Bar And Plates , G.I Pipe 40Mm Dia , Gi Plain Washer Thick , Twisted Steel/Deformed Bars , Hire Charges Of Concrete Mixer 0.25 To 0.40 Cum With Hopper , Vibrator (Needle Type 40 Mm) , Hire Charge Of 10 Hp Engine And Pump Set - Materials , Wall Form Panel 1250X500 Mm , Corner Angle 45X45x5 Mm 1.50 M Long , 100 Mm Channel Shoulder 2.5 M Long , Double Clip (Bridge Clip) , Single Clip , Wall Form Panel 1250X450xmm , Corner Angle 45X45x5 Mm 2.50 Long , Column Clamp 450X1070 Mm , Prop 2 M (2-3.5M) , Adjustable Telescopic Prop 3 M (2.02-3.75M) , Beam Clamp 300-380 Mm (450-1070 Mm) , Adjustable Span Eso+Si (2.35-3.40) , Second Class Kail Wood In Planks , Second Class Kail Wood In Scantling , Hollock Ballies 125 Mm Diameter , Solid Blocks Of Size 30X20x20cm , Solid Blocks Of Size 30X20x15cm , Hollow Blok Of Size 40X20x10cm , Interlocking cement concrete Paver Block (80 Mm Thick, M-30) , Pvc Vent Cowl 63 Mm Dia , Pvc Vent Cowl 110 Mm Dia , Brass Bib-Cock-15 Mm Dia , Pvc Pipe 63 Mm Outer Dia . 6Kgf/Cm2 , Pvc Pipe 110 Mm Outer Dia 6Kgf/Cm2 , Pvc Pipe 25 Mm Outer Dia . 12 Kgf/Cm2 , Pvc Pipe 32 Mm Outer Dia. 10Kgf/Cm2 , Pvc Elbow 63 Mm Dia , Pvc 45 Degree Elbow 63 Mm Dia , Pvc Door Elbow 63 Mm Dia , Pvc Bend 63 Mm Dia , Pvc Tee 63X63x63 Mm Dia , Pvc Socket/Coupling 63 Mm Dia , Pvc Elbow 110 Mm Dia , Pvc 45 Degree Elbow 110 Mm Dia , Pvc Door Elbow 110 Mm Dia , Pvc Bend 110 Mm Dia , Pvc Tee 110X110x110mm Dia , Pvc Socket/Coupling 110 Mm Dia , Pvc Pipe 40 Mm Outer Dia. 10Kgf/Cm2 , Pvc Pipe 20 Mm Outer Dia 10 Kfg/Cm2 , Pvc Pipe 63 Mm Outer Dia . 4Kgf/Cm2 , Pvc Pipe 32 Mm Outer Dia 6Kgf/Cm2 , Pvc Pipe 40 Mm Outer Dia. 6Kgf/Cm2 , Pvc Pipe 75 Mm Outer Dia 6Kgf/Cm2 , Pvc Pipe 110 Mm Outer Dia. 4Kgf/Cm2 , Pvc Pipe 160 Mm Outer Dia. 4Kgf/Cm2 , Pvc Elbow 75 Mm Dia , Pvc 45 Degree Elbow 75 Mm Dia , Pvc Socket/Coupling 75 Mm Dia , Pvc Reducer 63X50 Mm Dia , Pvc Vent Cowl 75 Mm Dia , Vitreous China Orrisa Type W.C. Pan Size 580 Mm , Brass Stop-Cock 15 Mm Dia , Flushing Cistern P.V.C. 10 Lts Capacity (Low Level) (White) (With Fittings, Accessories And Flush Pipe) , 100 Mm S.C.I. Trap With Vent Heel , Black Plastic Seat (Soild) With Lid C.P.Brass Hinges And Rubber Buffers , Vitreous China Pedestal Type Water Closet , Stainless Steel Kitchen Sink - Without Drain Board 470X420 Mm Bowl Depth 178 Mm , C.I. Bracket For Wash Basin And Sinks , Polyethylene Water Storage Tank With Cover And Suitable Locking Arrangemnet , Vitreous China Flat Back Wash Basin 550X400 Mm , 15 Mm C.P.Brass Tap , C.P. Brass Waste 32 Mm , Rectangular Shape 453X357 Mm Mirror With Plastic Moulded Frame , Rawl Plug 50 Mm (Designation 10 Nos) , Ptmt - Towel Rail (600 Mm) , Chromium Plated Brass Screws 25 Mm , White Vitreous China 10 Lit. (Full Flush) Capacity Controlled Low Level Flushing Cistern With All Fittings , Factory Made Door Frame Size 50X47 Mm With Wall Thickness 5 Mm Made Of Single Piece Extruded Profile , 35 Mm Thick Factory Made Solid Panel Pvc Door Shutter Of Single Piece Extruded Profile Non Decorative Finished (Matt Finished) , Float Glass Sheet Of Nominal Thickness 4 Mm (Weight Not Less Than 10 Kg/Sqm) , Aluminium T Or L Sections , Hard Board 6 Mm Thick , Powder Coating 50 Microns On Aluminium Sections , Neoprene / Epdm Rubber Gasket , Second Class Teak Wood In Scantling , 200 Mm Aluminium Aldrop , Multi Surface Paint , Special Primer (C.W) , Synthetic Enamel Paint In Black Or Chocolate Shade , Acrylic Exterior Paint , Premium Acrylic Emulsion Of Interior Grade, Having Voc Content Less Than 50 Gm/Litre , Exterior Primer , Epoxy Paint , Deharadun White Lime , Vitrified Floor Tile 60X60 Cm , Ceramic Glazed Tiles Ist Quality 300 X 300 Mm In All Shades And Designs Of White, Ivory, Grey, Fume Red Brown Etc. , Ceramic Glazed Tiles Ist Quality Minimum Thickness 5 Mm In All Colours Shades And Designs Except Burgundy, Bottle Green Black , Bamboo Nails , Aracanut Post , Royalty For Good Earth , Common Burnt Clay F.P.S. (Non Modular) Bricks Class Designation 7.5

BOQ

Name of Work:- Chalavara grama panchayath ,Vendor selection for supply of various mterials for VB-G RAM (G)
Sl. No. Item Description
1QUARRY WASTE
2Stone Aggregate(single size): 40 mm nominal size
3Stone Aggregate(single size):20 mm nominal size
4Stone Aggregate(single size): 10 mm nominal size
5Stone Aggregate(single size): 06 mm nominal size
6Fine sand (Zone IV)
7Coarse sand (zone III)
8gravel 5mm to 10mm
9Stone for masonry work
10Portland Cement
11M.S. Tube 40 mm dia
12Mild steel tubes hot finished welded type
13Galvanised steel bolts & nuts 6 mm dia and 25 mm long round head with slots
14Galvanised steel J or L hooks 8 mm dia
15G.I Limpet washer
16Bitumen washer
17Mild steel round bar 12 mm dia and below
18Mild Steel round bar above 12 mm dia
19Mild steel sheets with bolts and nuts to rest on pintels
20Iron pintels including weldded pin
21Mild steel sheets for tanks
22Mild steel hooks
23Mild steel plate
24Mild steel tubes electric resistant or induction butt welded
25Welding by electric plant
26Wire nails
27Bright finished or black enameled mild steel butt hinges 100x58x1.90 mm
28Bright finished or black enameled mild steel screws 40 mm
29Bright finished or black enameled mild steel screws 20 mm
30Powder coated M.S. butt hinges 100 mm X58 mm X 1.9 mm
31Flats up to 10 mm in thickness
32Galvanised wire mesh of average width of aperture 1.4 and nominal dia.of wire 0.63 mm
33G.I Trafford profile sheet 0.35mm thick
34Precoated Aluminium Traffored sheet 0.450 mm thick
35Structural steel such as tees,angles,channels and RS Joists
36Stainless steel screws 50 mm
37Red oxide Zinc chromate primer
38Precoated galvanised steel plain ridges
39Stainless steel (Grade - 304) hollow section round/square tubes
40Stainless steel bolts /square bar and plates
41G.I pipe 40mm dia
42GI plain washer thick
43Twisted steel/deformed bars
44Hire charges of Concrete Mixer 0.25 to 0.40 cum with Hopper
45Vibrator (Needle type 40 mm)
46Hire charge of 10 HP engine and pump set - Materials
47wall form panel 1250x500 mm
48Corner angle 45x45x5 mm 1.50 m long
49100 mm channel shoulder 2.5 m long
50Double clip (bridge clip)
51Single clip
52Wall form panel 1250x450xmm
53Corner angle 45x45x5 mm 2.50 long
54Column clamp 450x1070 mm
55Prop 2 m (2-3.5m)
56Adjustable telescopic prop 3 m (2.02-3.75m)
57Beam clamp 300-380 mm (450-1070 mm)
58Adjustable span ESO+SI (2.35-3.40)
59Second class kail wood in planks
60Second class kail wood in scantling
61Hollock ballies 125 mm diameter
62Solid blocks of size 30x20x20cm
63Solid blocks of size 30x20x15cm
64Hollow Blok of size 40x20x10cm
65Interlocking C.C. paver block (80 mm thick, M-30)
66PVC vent cowl 63 mm dia
67PVC vent cowl 110 mm dia
68Brass bib-cock-15 mm dia
69PVC pipe 63 mm outer dia . 6kgf/cm2
70PVC pipe 110 mm outer dia 6kgf/cm2
71PVC pipe 25 mm outer dia . 12 kgf/cm2
72PVC pipe 32 mm outer dia. 10Kgf/cm2
73PVC Elbow 63 mm dia
74PVC 45 degree Elbow 63 mm dia
75PVC door Elbow 63 mm dia
76PVC bend 63 mm dia
77PVC Tee 63x63x63 mm dia
78PVC Socket/coupling 63 mm dia
79PVC Elbow 110 mm dia
80PVC 45 degree Elbow 110 mm dia
81PVC door Elbow 110 mm dia
82PVC bend 110 mm dia
83PVC Tee 110x110x110mm dia
84PVC Socket/coupling 110 mm dia
85PVC pipe 40 mm outer dia. 10kgf/cm2
86PVC pipe 20 mm outer dia 10 kfg/cm2
87PVC pipe 63 mm outer dia . 4kgf/cm2
88PVC pipe 32 mm outer dia 6Kgf/cm2
89PVC pipe 40 mm outer dia. 6kgf/cm2
90PVC pipe 75 mm outer dia 6kgf/cm2
91PVC pipe 110 mm outer dia. 4kgf/cm2
92PVC pipe 160 mm outer dia. 4kgf/cm2
93PVC Elbow 75 mm dia
94PVC 45 degree Elbow 75 mm dia
95PVC Socket/coupling 75 mm dia
96PVC Reducer 63x50 mm dia
97PVC vent cowl 75 mm dia
98Vitreous China orrisa type w.c. pan size 580 mm
99Brass stop-cock 15 mm dia
100Flushing Cistern P.V.C. 10 lts capacity (low level) (white) (with fittings, accessories and flush pipe)
101100 mm S.C.I. trap with vent heel
102Black plastic seat (soild) with lid C.P.brass hinges and rubber buffers
103Vitreous china pedestal type water closet
104Stainless steel kitchen sink - without drain board 470x420 mm bowl depth 178 mm
105C.I. bracket for wash basin and sinks
106Polyethylene water storage tank with cover and suitable locking arrangemnet
107Vitreous china flat back wash basin 550x400 mm
10815 mm C.P.brass tap
109C.P. brass waste 32 mm
110Rectangular shape 453x357 mm Mirror with Plastic moulded frame
111Rawl plug 50 mm (designation 10 nos)
112PTMT - Towel Rail (600 mm)
113Chromium plated Brass screws 25 mm
114White Vitreous china 10 lit. (full flush) capacity controlled low level flushing cistern with all fittings
115Factory made door frame size 50x47 mm with wall thickness 5 mm made of single piece extruded profile
11635 mm thick factory made solid panel PVC door shutter of single piece extruded profile non decorative finished (Matt finished)
117Float glass sheet of nominal thickness 4 mm (weight not less than 10 kg/sqm)
118Aluminium T or L Sections
119Hard board 6 mm thick
120Powder coating 50 microns on aluminium sections
121Neoprene / EPDM rubber gasket
122Second class teak wood in scantling
123200 mm Aluminium aldrop
124Multi surface paint
125Special primer (C.W)
126Synthetic enamel paint in black or chocolate shade
127Acrylic exterior paint
128Premium acrylic emulsion of interior grade, having VOC content less than 50 gm/litre
129Exterior primer
130Epoxy paint
131deharadun white lime
132Vitrified floor tile 60x60 cm
133Ceramic Glazed Tiles Ist quality 300 x 300 mm in all shades and designs of White, Ivory, grey, Fume Red brown etc.
134Ceramic Glazed Tiles Ist quality minimum thickness 5 mm in all colours shades and designs except burgundy, bottle green black
135Bamboo nails
136Aracanut post
137Royalty for good earth
138Common burnt clay F.P.S. (non modular) bricks class designation 7.5 Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58483239
AUTHORITY Local Bodies
TENDER VALUE 40 Lakhs
LAST DATE 19-11-2026
Authority
Authority Name Grama Panchayat
Work Description Tender for Chalavara Grama Panchayath ,Vendor Selection For Supply Of Various Mterials For Vb-G Ram (G) , Quarry Waste , Stone Aggregate(Single Size): 40 Mm Nominal Size , Stone Aggregate(Single Size):20 Mm Nominal Size , Stone Aggregate(Single Size): 10 Mm Nominal Size , Stone Aggregate(Single Size): 06 Mm Nominal Size , Fine Sand (Zone Iv) , Coarse Sand (Zone Iii) , Gravel 5Mm To 10Mm , Stone For Masonry Work , Portland Cement , M.S. Tube 40 Mm Dia , Mild Steel Tubes Hot Finished Welded Type , Galvanised Steel Bolts & Nuts 6 Mm Dia And 25 Mm Long Round Head With Slots , Galvanised Steel J Or L Hooks 8 Mm Dia , G.I Limpet Washer , Bitumen Washer , Mild Steel Round Bar 12 Mm Dia And Below , Mild Steel Round Bar Above 12 Mm Dia , Mild Steel Sheets With Bolts And Nuts To Rest On Pintels , Iron Pintels Including Weldded Pin , Mild Steel Sheets For Tanks , Mild Steel Hooks , Mild Steel Plate , Mild Steel Tubes Electric Resistant Or Induction Butt Welded , Welding By Electric Plant , Wire Nails , Bright Finished Or Black Enameled Mild Steel Butt Hinges 100X58x1.90 Mm , Bright Finished Or Black Enameled Mild Steel Screws 40 Mm , Bright Finished Or Black Enameled Mild Steel Screws 20 Mm , Powder Coated M.S. Butt Hinges 100 Mm X58 Mm X 1.9 Mm , Flats Up To 10 Mm In Thickness , Galvanised Wire Mesh Of Average Width Of Aperture 1.4 And Nominal Dia.Of Wire 0.63 Mm , G.I Trafford Profile Sheet 0.35Mm Thick , Precoated Aluminium Traffored Sheet 0.450 Mm Thick , Structural Steel Such As Tees,Angles,Channels And Rs Joists , Stainless Steel Screws 50 Mm , Red Oxide Zinc Chromate Primer , Precoated Galvanised Steel Plain Ridges , Stainless Steel (Grade - 304) Hollow Section Round/Square Tubes , Stainless Steel Bolts /Square Bar And Plates , G.I Pipe 40Mm Dia , Gi Plain Washer Thick , Twisted Steel/Deformed Bars , Hire Charges Of Concrete Mixer 0.25 To 0.40 Cum With Hopper , Vibrator (Needle Type 40 Mm) , Hire Charge Of 10 Hp Engine And Pump Set - Materials , Wall Form Panel 1250X500 Mm , Corner Angle 45X45x5 Mm 1.50 M Long , 100 Mm Channel Shoulder 2.5 M Long , Double Clip (Bridge Clip) , Single Clip , Wall Form Panel 1250X450xmm , Corner Angle 45X45x5 Mm 2.50 Long , Column Clamp 450X1070 Mm , Prop 2 M (2-3.5M) , Adjustable Telescopic Prop 3 M (2.02-3.75M) , Beam Clamp 300-380 Mm (450-1070 Mm) , Adjustable Span Eso+Si (2.35-3.40) , Second Class Kail Wood In Planks , Second Class Kail Wood In Scantling , Hollock Ballies 125 Mm Diameter , Solid Blocks Of Size 30X20x20cm , Solid Blocks Of Size 30X20x15cm , Hollow Blok Of Size 40X20x10cm , Interlocking cement concrete Paver Block (80 Mm Thick, M-30) , Pvc Vent Cowl 63 Mm Dia , Pvc Vent Cowl 110 Mm Dia , Brass Bib-Cock-15 Mm Dia , Pvc Pipe 63 Mm Outer Dia . 6Kgf/Cm2 , Pvc Pipe 110 Mm Outer Dia 6Kgf/Cm2 , Pvc Pipe 25 Mm Outer Dia . 12 Kgf/Cm2 , Pvc Pipe 32 Mm Outer Dia. 10Kgf/Cm2 , Pvc Elbow 63 Mm Dia , Pvc 45 Degree Elbow 63 Mm Dia , Pvc Door Elbow 63 Mm Dia , Pvc Bend 63 Mm Dia , Pvc Tee 63X63x63 Mm Dia , Pvc Socket/Coupling 63 Mm Dia , Pvc Elbow 110 Mm Dia , Pvc 45 Degree Elbow 110 Mm Dia , Pvc Door Elbow 110 Mm Dia , Pvc Bend 110 Mm Dia , Pvc Tee 110X110x110mm Dia , Pvc Socket/Coupling 110 Mm Dia , Pvc Pipe 40 Mm Outer Dia. 10Kgf/Cm2 , Pvc Pipe 20 Mm Outer Dia 10 Kfg/Cm2 , Pvc Pipe 63 Mm Outer Dia . 4Kgf/Cm2 , Pvc Pipe 32 Mm Outer Dia 6Kgf/Cm2 , Pvc Pipe 40 Mm Outer Dia. 6Kgf/Cm2 , Pvc Pipe 75 Mm Outer Dia 6Kgf/Cm2 , Pvc Pipe 110 Mm Outer Dia. 4Kgf/Cm2 , Pvc Pipe 160 Mm Outer Dia. 4Kgf/Cm2 , Pvc Elbow 75 Mm Dia , Pvc 45 Degree Elbow 75 Mm Dia , Pvc Socket/Coupling 75 Mm Dia , Pvc Reducer 63X50 Mm Dia , Pvc Vent Cowl 75 Mm Dia , Vitreous China Orrisa Type W.C. Pan Size 580 Mm , Brass Stop-Cock 15 Mm Dia , Flushing Cistern P.V.C. 10 Lts Capacity (Low Level) (White) (With Fittings, Accessories And Flush Pipe) , 100 Mm S.C.I. Trap With Vent Heel , Black Plastic Seat (Soild) With Lid C.P.Brass Hinges And Rubber Buffers , Vitreous China Pedestal Type Water Closet , Stainless Steel Kitchen Sink - Without Drain Board 470X420 Mm Bowl Depth 178 Mm , C.I. Bracket For Wash Basin And Sinks , Polyethylene Water Storage Tank With Cover And Suitable Locking Arrangemnet , Vitreous China Flat Back Wash Basin 550X400 Mm , 15 Mm C.P.Brass Tap , C.P. Brass Waste 32 Mm , Rectangular Shape 453X357 Mm Mirror With Plastic Moulded Frame , Rawl Plug 50 Mm (Designation 10 Nos) , Ptmt - Towel Rail (600 Mm) , Chromium Plated Brass Screws 25 Mm , White Vitreous China 10 Lit. (Full Flush) Capacity Controlled Low Level Flushing Cistern With All Fittings , Factory Made Door Frame Size 50X47 Mm With Wall Thickness 5 Mm Made Of Single Piece Extruded Profile , 35 Mm Thick Factory Made Solid Panel Pvc Door Shutter Of Single Piece Extruded Profile Non Decorative Finished (Matt Finished) , Float Glass Sheet Of Nominal Thickness 4 Mm (Weight Not Less Than 10 Kg/Sqm) , Aluminium T Or L Sections , Hard Board 6 Mm Thick , Powder Coating 50 Microns On Aluminium Sections , Neoprene / Epdm Rubber Gasket , Second Class Teak Wood In Scantling , 200 Mm Aluminium Aldrop , Multi Surface Paint , Special Primer (C.W) , Synthetic Enamel Paint In Black Or Chocolate Shade , Acrylic Exterior Paint , Premium Acrylic Emulsion Of Interior Grade, Having Voc Content Less Than 50 Gm/Litre , Exterior Primer , Epoxy Paint , Deharadun White Lime , Vitrified Floor Tile 60X60 Cm , Ceramic Glazed Tiles Ist Quality 300 X 300 Mm In All Shades And Designs Of White, Ivory, Grey, Fume Red Brown Etc. , Ceramic Glazed Tiles Ist Quality Minimum Thickness 5 Mm In All Colours Shades And Designs Except Burgundy, Bottle Green Black , Bamboo Nails , Aracanut Post , Royalty For Good Earth , Common Burnt Clay F.P.S. (Non Modular) Bricks Class Designation 7.5
Basic Detail
Tender No SC1-1235/2026
Bidding Type Tender
Location
City Palakkad
State Kerala
Key Dates
Publish Date 11 Nov 2026
Submission Date 19 Nov 2026
Open Date 23 Nov 2026
Finance
Tender Value 40 Lakhs
Tender Fee 2500
EMD 50000
Exemption Available
Document List
BOQ_1515641.xls
cfc37209-1625-4992-b4cf-7e883e829dfe.html
NIT.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 11, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Nov 19, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 4 days
Nov 23, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 8 days

Tender Documents

Download All (ZIP) ↓
xls

BOQ_1515641.xls

html

cfc37209-1625-4992-b4cf-7e883e829dfe.html

pdf

NIT.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender