Tender For Construction Of Administration Block (14-Battalion & Air Squadron) G+2 At Ncc Campus, Imphal West, Manipur.
Tender Value
13.29 Crore
Estimated cost
Bid Submission
02 Dec 2026
11 days left
EMD
23.29 Lakhs
Bank guarantee accepted
Document Fee
5000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Imphal West → Manipur
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Administration Block (14-Battalion & Air Squadron) G+2 At Ncc Campus, Imphal West, Manipur.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means {Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1. 5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc., in layers not exceeding 20mm in depth consolidating each deposited layer by ramming and watering and lead upto 50m and lift of 1.5m. |
| 3 | Supplying and filling in plinth with sandy soil under floors i/c watering, ramming, consolidating and dressing complete. |
| 4 | Earth work in rough excavation, banking excavated earth in layers not exceeding 20 cm in depth, breaking clods watering, rolling each layer with ½ tonne roller or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions, lead upto 50 m and lift upto 1.5 m : |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering- All work upto Plinth Level. 1 : 4 : 8 ( 1 cement:4 coarse sand:8 graded stone aggt. 40 mm nominal size ) |
| 6 | Boring, providing and installation bored cast-in-situ reinforced cement pile of specified diameter and length below the pile cap M 25 in cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with casing and/ or bentonite solution and the length of pile to be embeded in the pile cap etc. all completed(Length of the pile for payment shall be measured up to bottom of pile cap) Note: Truck Mounted rotary/TMR/ Tubewell boring machine shall not be used. (a) 450 mm diameter |
| 7 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana I Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All works upto Plinth level. Concrete of M-25 grade with minimum cement content of 330 kg/cum. |
| 8 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana I Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All works above Plinth level upto floor V Level. Concrete of M-25 grade with minimum cement content of 330 kg/cum. |
| 9 | Reinforcement for RCC work i/c straightening, cutting, bending, placing in position and binding all complete up to plinth level. (a) Thermo-Mechanically Treated bars. |
| 10 | Centering and shuttering including strutting, propping etc and removal of form for: |
| 11 | (a) Foundation, footings, bases of columns etc. |
| 12 | (b) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. |
| 13 | (d) Suspended floors, roofs, landings, balconies and access platform, with water proof ply 12mm thick. |
| 14 | (b) Columns, Pillars,Piers,Abutments, Posts and Struts . |
| 15 | (c) Lintels, beams, plinth beams, girders,bressurmers and cantilevers, with waterproof ply 12 mm thick. |
| 16 | (g) Stairs, (excluding landings) except spiral-staircases. |
| 17 | Brickwork with 1st class common burnt clay FPS (non modular) bricks in foundation and plinth - cement mortar 1:4 (1 cement : 4 coarse sand) |
| 18 | Half brick masonry with 1st class common burnt clay F.P.S. (non modular) bricks in superstructure above plinth level upto floor V level in Cement mortar 1:4( 1 cem : 4 c / sand ) |
| 19 | Providing wood work in frames of doors, windows, clerestory windows and other frames wrought, framed and fixed in position with hold fast lugs or with dash fastener of required dia and length (hold fast lugs or dash fastener shall be paid for seperately.- a) Local best quality teak wood. |
| 20 | Providing and fixing panell or panelled and glazed shutter for doors, windows and clerestory windows including ISIS marked MS butt hinges of required size with necessary screws excluding panelling which will be paid for seperately, all complete as per direction of engineer in charge.- a) Local best quality Teak wood - 35 mm thick shutters |
| 21 | Providing and fixing aluminium sliding door bolts ISi marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 300x16 mm |
| 22 | Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles with necessary screws etc. complete (best make of approved quality). |
| 23 | Providing & fixing bright finished brass Tower bolts (barrel type) with necessary screws etc. complete. |
| 24 | (a) 250x10 mm. |
| 25 | (b)150 x 10 mm |
| 26 | Providing and fixing chromium plated brass handles with necessary screws etc. complete: |
| 27 | (a) 125mm |
| 28 | (b) 75 mm |
| 29 | Providing and fixing bright finished brass hard drawn hooks and eyes : |
| 30 | (a) 250 mm |
| 31 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10 x 15cm 1 :3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) |
| 32 | Providing and fixing ISi marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: (a) 125x75x4 mm |
| 33 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc. |
| 34 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing and staircase railing including applying a priming coat of approved steel primer. M.S. tube |
| 35 | Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar bent to shape with hooked ends in R.C.C. slabs, beams during laying including painting the exposed portion of loop, all as per standard design complete. |
| 36 | Providing and fixing in position collapsible steel shutters with vertical channels 20xl0x2mm and braced with flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia, steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer |
| 37 | Steel work in built up tubular (round, square or rectangular tubes etc.) trusses et., including cutting, hoisting fixing in position and applying a priming coat of approved steel primer, including welding and bolted including special shaped washers etc. complete.- a ) Electric resistance or induction butt welded tubes |
| 38 | Providing and fixing precoated galvanised iron profile sheet ( size, shape and pitch of corrugation as approved by Enginner-in-charge) with zinc coating of 120 grams per sqmt as per IS:277, in 240 mpa steel grade, 5-7 microns epoxy primer on both sides of the sheet and polyster top coat 15-18 micron. Shet sholuld have protective guard film of 25 micron minimum to avoid scratces during transportation and should be supplied in single lenfth upto 12 mt or as desired by engineer in charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal / vertical or curve surface, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required with. (a) precoated galvanised iron profile sheets 0.50 mm thick |
| 39 | Providing and fixing precoated galvanised steel sheet roofing accessories , Zinc coating 120gsm as per IS: 277 in 240mpa steel arade, 5-7 microns epoxy primer on both side of the sheet and Dolvester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L'hooks, bolts and nuts and or GL. seam bolts and nuts, G.!. plain and bitumen washers Complete: Ridges Plain (500-600mm).Precoated Galvanised iron profile sheets 0.50mm thick. |
| 40 | Ridges plain (500-600mm) Precoated galvanised iron profile sheets 0.35 mm thick |
| 41 | Barge board (Upto 300 mm) Precoated galvanised iron profile sheets 0. 50 mm thick |
| 42 | Gutter (600mm over all girth) Precoated galvanised iron profile sheets 0.50 mm thick |
| 43 | Providing and fixing at all height false ceiling including providing and fixing of frame work made of special sections, power pressed from M.S. sheet and galvanised with zinc coating of 120 gms/ sqm (both sided inclusive) as per IS: 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5mm diax50mm long with 6mm dia bolts.other flange of cleat fixed to the angle hangers of 25x25x0.55mm of required length with nuts and bolts of required size and the other end of the angle hanger fixed with intermediate G.I. channels 45x15x0. 9mm running at the spacing of 1200mm centre to centre, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre, with 25mm long drive-all screws @ 230mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishng to a flush finish of tapered and square edges of the board with recommended jointing compound,jointing tapes, finishing with jointing compund in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board.all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, and specification and direction of the Engineer in Charge but excluding the cost of painting with : |
| 44 | (i) Fully Perforated Gypsum Plaster Board of size 1200 x 2400 x 12. 5 mm having approx. 15% perforated size and pattern as approved by the Engineer-in-charge and as per manufacter's specification, with all 4 sides tapered and backed by acoustical tissue with NRC value not less than 0.60. |
| 45 | Providing wood work in frames of false ceiling, partitions etc. sawn and put up in position : Local best quality Uningthou wood |
| 46 | Providing and fixing Echoseal Premium Acoustic Panel |
| 47 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1 :4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily Double charge vitrified tile polished finish of size of Tile 600 x 1200 mm |
| 48 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1 :3 (1 cement: 3 coarse sand} and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 49 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm ( average ) thick base of cement mortar 1 : 4 ( 1 cement: 4 coarse sand ) laid and pointing with cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer -in - Charge. Polished Granite stone slab Jet Black, Cherry Red, Elite Brown Cat Eye or equivalent. |
| 50 | Providing and laying factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. 80 mm thick |
| 51 | 12 mm cement plaster of mix 1 :4 (1 cement : 4 coarse sand) |
| 52 | 15 mm cement plaster 1 :3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement on the roughside of single or half brick wall. |
| 53 | Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth Inner Wall and Ceiling |
| 54 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content. With water thinnable cement primer on wall surface having |
| 55 | Varnishing with varnish of approved brand and manufacture: Two or more coats of glue sizing with copal varnish over an under coat of flatting varnish. |
| 56 | Applying priming coats with primer of approved brand and manufacture, having low voe (Volatile Organic Compound) content. With ready mixed red oxide zinc chromatic on steel / iron works having voe content less than 250 grams/ litre |
| 57 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture. |
| 58 | Painting with silicon & acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces: Two coat |
| 59 | Making plinth protection 50mm thick of cement concrete 1 :3:6 (1 cement : 3 coarsesand : 6 graded stone aggregate 20 mm nomina size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 60 | LINE BRICK DRAIN:- |
| 61 | Earthwork in excavation by mrchanical means (hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth 1.5 m in width as well as 10 sqm on plan ) including getting out and disposal of excavated earth, lead upto 50 mt and lift upto 1.5 m as directed by th engineer in charge. All kind of soil |
| 62 | Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc., in layers not exceeding 20mm in depth consolidating each deposited layer by ramming and watering and lead upto 50m and lift of 1.5m. |
| 63 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering- All work upto Plinth Level. 1 : 2 : 4 ( 1 cement:2 coarse sand:4 graded stone aggt. 20 mm nominal size ) |
| 64 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering- All work upto Plinth Level. 1 : 4 : 8 ( 1 cement:4 coarse sand:8 graded stone aggt. 40 mm nominal size ) |
| 65 | Brickwork with 1st class common burnt clay FPS (non modular) bricks in foundation and plinth - cement mortar 1:4 (1 cement : 4 coarse sand) |
| 66 | 15 mm cement plaster 1 :3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement on the roughside of single or half brick wall. |
| 67 | SANITARY ITEMS/ WATER SUPPLY |
| 68 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.1. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISi marked white solid plastic seat and lid. |
| 69 | Providing and fixing wash basin with C.l. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern. including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P.brass pillar taps |
| 70 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x41 0x265 mm sizes respectively with utomatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern |
| 71 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with One step CPVC solvent cement and the cost of cutting chases and direction making good of Engineer the same in Chargeincluding testing of joints complete as per Concealed work, including cutting chases and making good the wall etc (a) 15mm Diameter |
| 72 | (a) 15mm Diameter |
| 73 | (a) 25mm Diameter |
| 74 | P/F C.P. brass bib cock of approved quality conforming to IS 8931 (a)15mm nominal bore |
| 75 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. (a)15mm diameter. |
| 76 | Providing and fixing unplasticised -PVC pipe clips of approved design to Unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs,screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar cement: 4 coarse sand) and making good the wall etc. complete. 110mm |
| 77 | P/F 110mm PVC door bend pipe of approved quality i/c filling the joints with rubber gasket and solvent cement etc. complete. |
| 78 | P/F HCI traps with 100 mm inlet and 100mm outlet of self cleaning design with HCI screwed down of hinged grating with or without vent arm complete i/c cost of cutting and making good the walls and floors. |
| 79 | Providing and placing on terrace (at all floor level) polyethylene water storage tank, IS: 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipe but without fitting and the base support for tank. |
| 80 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 81 | Providing and fixing toilet paper holder C.P. brass |
| 82 | Providing and fixing PTMT towel rail complete with brackets fixeings to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms |
| 83 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. |
| 84 | IEI :- |
| 85 | Wiring for light point / Fan point / Exhaust Fan point / Call bell point with 1.5mm2 FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit with modular type switch , modular plate suitable size G.I. box and earthing the point with 1.5mm2 FR PVC insulated copper coductor single core etc. as reqd. |
| 86 | 1. Group A |
| 87 | 2. Group B |
| 88 | 3. Group C |
| 89 | Wiring for twin control light point with 1.5mm2 FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, 2 way switch, modular plat, modular type switch suitable size G.I. box and earthing the point with 1.5mm2 FR PVC insulated copper coductor single core etc. as reqd. |
| 90 | Wiring for light point / power point plug with 2x4mm2 FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit along with 1 no. 4mm2 FR PVC insulated copper conductor single core cable for loop earthing etc. as reqd. |
| 91 | Wiring for circuit / sub-main wiring along with earth wire with (the following sizes) of FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit etc. as reqd. |
| 92 | 1. 2x1.5mm2 + 1x1.5mm2 earth wire. |
| 93 | 2. 2x2.5mm2 + 1x2.5mm2 earth wire. |
| 94 | 3. 2x4mm2 + 1x4mm2 earth wire. |
| 95 | 10. 4x6mm2 + 2x6mm2 earth wire. |
| 96 | 11. 4x10mm2 + 2x10mm2 earth wire. |
| 97 | S/F suitable size G.I. box with modular plate and cover in front on surface or in recess i/c P/F 3 pin 5/6 amp modular socket outlet 5/6 amp modular switch, connection painting etc. as reqd. |
| 98 | S/F suitable size G.I. box with modular plate and cover in front on surface or in recess i/c P/F 6 pin 15/16 and 5/6 amp modular socket outlet 15/16 amp modular switch, connection painting etc. as reqd. |
| 99 | S/F 48\\" Sweep (1200mm) A.C Ceiling fan complete with down rod, canopy,3(three) blades but without regulator etc. as reqd. (make Bajaj/Usha or similar). |
| 100 | Suppying & Fixing stepped type electronic fan regulator on the existing modular plate switch box i/c connection but excluding modular plate etc. as reqd. |
| 101 | S/F of 305mm sweep exhauset fan complete with all accessories i/c connection etc. as reqd. |
| 102 | S/F 8 way, (4+24 way) single door TPN prewired, sheet steel MCB distribution board, 240V on surface/recessed complete with loose wire box, terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnection, phospohorized power painted i/c earthing etc as reqd (but without MCB/RCCB/Isolator). |
| 103 | P/F 40 amp. Four pole 240V isolator in the existing MCB DB complete with connection testing and commissioning etc. as reqd. |
| 104 | P/F 63 amp. four pole 240V isolator in the existing MCB DB complete with connection testing and commissioning etc. as reqd. |
| 105 | P/F 5 amp. to 32 amp. rating 230V 'B' series MCB for lighting and other load of single pole in the existing MCB DB complete with connection testing and commissioning etc. as reqd. |
| 106 | Fabrication of control panel board by 16 gauge steel sheet, along with components mounting, making strip wiring auxiliary components, wiring all over the panel i/c fixing charge, painting etc. as reqd. |
| 107 | Indicating Lamp |
| 108 | Voltmeter range 0-500 volts. |
| 109 | Ammeter range 0-200 volts. |
| 110 | Current transformer coil range 0-200 amp. |
| 111 | Hinges for panel door |
| 112 | Panel door locks. |
| 113 | Selector switch for ammeter & voltmeter. |
| 114 | Providing and fixings 4 pole MCCB 160 amp. 25 KA in existing cubicle panel board including drilling holes in cubicle panel & making connection etc. as reqd. |
| 115 | S/F bus bar chamber with 4 strip scopper bus bar of length suitable for 200A capacity complete with all accessories i/c connection earthing the body etc as reqd. |
| 116 | p/f lighting conductor finial made of 25mm dia 300mm long copper tube having single prong at top with 85mm dia 3mm thick copper plate i/c holes etc. Complete as reqd |
| 117 | P/F copper tape in horizontal run p/f copper tape 2ommx3mm thick on parapet or surface of wall for lightning conductor as reqd(for horizontal run) |
| 118 | p/f copper tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as reqd(for vertical run) |
| 119 | Earthing with Copper earth Plate 600mmx600mmx6mm thick i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) as reqd. |
| 120 | Extra for using salt and charcoal for G.I. or copper plate earth electrode as reqd. |
| 121 | P/F earth bus of 25mmx5mm copper strip on surface or in recessed for connection etc. as reqd. |
| 122 | Supply of 50mm2 4-core PVC/XLPE insulated heavy duty armoured cable 1.1KV grade. |
| 123 | Laying of 1 no. PVC insulated PVC sheathed power cable of 1.1KV grade of size not less than 25mm2 but not exceeding 120mm2 direct in ground i/c excavation, sand cushioning, protective covering and re-filling the trench etc. as reqd. |
| 124 | S/F Surface mounting 12W LED down lighter i/c connection etc as reqd. ( Make- Havell: ZIVSURRDDLR12WLED830S or similar) |
| 125 | S/F Surface mounting 18W LED down lighter i/c connection etc as reqd. ( Make- Havell: ZIVSURRDDLR18WLED830S or similar) |
| 126 | S/F recess mounting 2x2 LED down light i/c connection etc as reqd. ( Make- Havell: BOCR2X2R36WLED857SPCMSEXE or similar) |
| 127 | Supply and fixing of CO2 type fire extinguisher having 4.5 Kg capacity ISI marked for IS 2878 filled with CO2 gas with 1 mtr long horn pipe fixing with dash fastener complete in all respect i/c numbering etc as required. |
| 128 | Providing and fixing of ABC type Stored Pressure type fire extinguisher having 6 kg capacity ISI marked under IS:15683 complete with imported Mono Ammonium Phosphate based ABC Powder suitable for all classes of fire. |
| 129 | SUBSTATION |
| 130 | 9.0 m S.T.P.(410:SP-31) |
| 131 | Channel 100×50,@7.9 kg/m 2.8×2 for supporting transformer |
| 132 | Channel 100×50,@7.9 kg/m 2.8×2 for DP X-arm |
| 133 | Channel 100×50,@7.9 kg/m 0.46×2 for supporting of item 2 |
| 134 | Channel 75×[email protected]/m 2×2.8m for HG fuse unit & AB switch |
| 135 | Clamp for Transformer belting |
| 136 | Channel 75×[email protected]/m 2×0.5m for supporting HG fuse main channel X-arm |
| 137 | Angle (50x50x6)mm 2.8x2 @4.5kg/m transformer belting and angle(35x35x5),[email protected]/m. Transformer belting support |
| 138 | Clamp for transformer base channel for MS flat [email protected]/m 0.27mx2 |
| 139 | Clamp for AB switch bracing 50x8mm@ 3.1kg/m 0.23mx2=0.46m |
| 140 | Clamp for DB Box Cross Arm |
| 141 | Distribution Transformer 100 kVA, Efficiency Level-II |
| 142 | 11 kV A.B.Switch 200 Amp |
| 143 | Horn gap fuse unit/D.O fuse, 3-ph |
| 144 | 3 Way D.B box with complete accessories with kit kat |
| 145 | 1.1KV grade 3.5 core 120 sq.mm PVC insulated al. power cable |
| 146 | D.B box cross arm of MS angle 35x35x5mm @ 2.6kg/m 2.8x2=5.6m |
| 147 | Sub-station Earthing |
| 148 | Sub-station Fencing |
| 149 | Danger board |
| 150 | 11 kV lighting arrester |
| 151 | Nuts & Bolts with washers. |
| 152 | (5/8)\\" x 3\\" |
| 153 | (5/8)\\" x 8.5\\" |
| 154 | Pole muffing |
| 155 | Pole painting |
| 156 | HT LINE |
| 157 | 8.0 m S.T.P.(410:SP-14) |
| 158 | LT Cross Arm 0.5 m long MS Angle |
| 159 | Back clamp for cross arm |
| 160 | Dead end fitting for AB Cables with bare messenger wire complete with eye hook as per construction standard |
| 161 | Suspension fitting for AB Cables with bare messenger wire complete with eye hook as per construction standard |
| 162 | Insulation pierching connector for AB Cable Big Size (Main: 16-95sq.mm, Service: 4-35(50) sq.mm) as per TS & construction standards. |
| 163 | AB Cables (3x50 + 1x35) sq.mm |
| 164 | Stay Set complete with stay wire, base plate, stay rod, stay insulator,clamp etc. |
| 165 | Bolts & Nuts with washer (5/8x3'' full thread) |
| 166 | Pole Muffing |
| 167 | Pole painting |
| 168 | LT LINE |
| 169 | 8.0 m S.T.P.(410:SP-14) |
| 170 | LT Cross Arm 0.5 m long MS Angle |
| 171 | Back clamp for cross arm |
| 172 | Dead end fitting for AB Cables with bare messenger wire complete with eye hook as per construction standard |
| 173 | Suspension fitting for AB Cables with bare messenger wire complete with eye hook as per construction standard |
| 174 | Insulation pierching connector for AB Cable Big Size (Main: 16-95sq.mm, Service: 4-35(50) sq.mm) as per TS & construction standards. |
| 175 | AB Cables (3x50 + 1x35) sq.mm |
| 176 | Stay Set complete with stay wire, base plate, stay rod, stay insulator,clamp etc. |
| 177 | Bolts & Nuts with washer (5/8x3'' full thread) |
| 178 | Pole Muffing |
| 179 | Pole painting |
| 180 | SOLAR PLANT AND STREET LIGHT |
| 181 | S/F steel tubular pole 6 mtr. Long 70mm dia. with base plate i/c painting etc. as reqd. |
| 182 | P/L (0.45x0.45x0.90)+(0.90x0.90x0.90)cum type muffing for errection of 4 mtr. Long pole embaded in 1:3:6 ( 1 cement :3 c/sand : 6 stone aggt. of 40mm nominal gause i/c centering & shuttering the earth work etc. as reqd. |
| 183 | S/F 15 Watt Solar Street Lamp complete with bulb, battery and solar plate i/c connection etc. as reqd. |
| 184 | Supplying , Installation, Testing & commissioning of 20 KW Hybrid type Solar Power Plant including all accessories as reqd. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 11, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 02, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 11 daysDec 02, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 11 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender