Tender For Fabrication Of Room Over The Edp Room At North West Corner Of Electrical Work Shop
Tender Value
4.30 Lakhs
Estimated cost
Bid Submission
24 Nov 2026
9 days left
EMD
10770
Bank guarantee accepted
Document Fee
1020
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kollam → Kerala
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Fabrication Of Room Over The Edp Room At North West Corner Of Electrical Work Shop
BOQ
| Sl. No. | Item Description |
| 1 | GI frame work welding cutting fixing over the RCC slab with baseplate anchored into slab etc including 1 coat primer. |
| 2 | Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete |
| 3 | RCC beam at bottom periphery |
| 4 | Providing and laying up to floor five level reinforced cement concrete in kerbs, steps and the like excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (Zone - III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 5 | Centering and shuttering |
| 6 | Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers |
| 7 | Steel reinforcement bars |
| 8 | Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelHard drawn steel wire |
| 9 | Painting the GI structures with 2 coats of anticorrosive bitumastic paint |
| 10 | Painting with black anti- corrosive bitumastic paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 11 | Providing and wrapping the GI structures with hot torch applied anti corrosive wrapping tape as per the instruction of engineer in charge |
| 12 | Providing and wrapping the structural steel item with Coal tar based anticorosion tape for protection of MS/GI structurals as per IS 15337:2003. Thickness of the tape shall be 3 mm. The material shall be fixed as per the instruction of engineer in charge. The wrapping tape shall be overlapped on each wrap to avoid exposed surface. Ref. MS fabrication of room over EDP room at north west corner of electricalworkshop 2026 MS work. Rate taken from Indiamart Dtd 16-09-2026 Pipe Wrap CT 10221 (Hot Applied Anti-Corrosive Bituminous Tape). Rs. 1850/roll. One roll is 10 m2. Total 60 m2 area. One roll of tape is having 2m2 area. Total 2 workers shall work for 2 days to complete this job. |
| 13 | Double sided partition with cement board of 8 mm thick incl putty work and cement primer application. Eventhough at both sides of GI frame, cement board to be fixed, area of one side only will be measured for payment. |
| 14 | Double sided partition with cement board of 8 mm thick incl putty work and cement primer application.Providing and fixing partition upto ceiling height consisting of required cement board, with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete. Double skinned (Means cement board at both sides of metal frames) 66 mm overallthickness partition using 8 mm thick double skin multipurpose cement board reinforced with cellulose fibre/ any approved material manufactured by well known companies as instructed by engineer in charge as per IS : 14862 with suitable fibre cement screws. Including application of putty work with joint tape at joints and application of cement primer of aproved manufacturer. One side area only will be measured. |
| 15 | Providing and fixing 8mm thick single cement board cut into suitable size over GI frames for parapet and rack top. Primering is not included in this item. |
| 16 | Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately).6 mm thick cement fiber board as per IS: 14862 |
| 17 | Applying external wall putty over single skinned cement board |
| 18 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 19 | Applying 2 coats of primer over cement board (Singles skinned only) provided for rack and parapet board |
| 20 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer |
| 21 | Scrapping and removing existing building painting |
| 22 | Removing white or colour wash by scrapping and sand papering and preparing thesurface smooth including necessary repairs to scratches etc. complete. |
| 23 | Painting existing walls |
| 24 | Finishing walls with Acrylic Smooth exterior paint of required shade :Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface |
| 25 | Roofing with PVC roofing sheet 2mm or more thick layer fixed with zinc phosphated bolts of approved manufacturer like Aargee Associates or equivalent etc. |
| 26 | Providing & fixing PVC corrugated roofing sheets of good quality up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8 mm dia G. I plain/ bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. |
| 27 | Vitrified tiling works for floor skirting edge thickening etc. |
| 28 | Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile600x600 mm |
| 29 | Epoxy grouting for tiling works |
| 30 | Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 600x600 mm |
| 31 | FRP single moulded glazed door frames |
| 32 | Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of crosssection 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminated shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame. |
| 33 | FRP door shutters |
| 34 | Providing and fixing to existing door frames.30 mm thick Fiberglass Reinforced Plastic (F.R.P) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF) / Polystyrene foam to be used all filler material throughout the hollow panel, casted monoolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS : 14856, complete as per direction of Engineerin- charge. |
| 35 | Providing and fixing 4mm thick float glass on FRP door with necessary fittingsetc |
| 36 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) |
| 37 | Providing and fixing 5mm or above size tempered / toughened glass on GI frame works with necessary rubber gaskets, silicon sealant, clips etc |
| 38 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) |
| 39 | Providing hydraulic Door closer |
| 40 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width form 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 41 | Providing and fixing chromium plated brass 100 mm mortice latch |
| 42 | Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. |
| 43 | Stainless steel butt hinges with stainless steel screws 125x64x1.90 mm |
| 44 | Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete:125x64x1.90 mm |
| 45 | Providing and fixing aluminium hanging floor door stopper |
| 46 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Single rubber stopper |
| 47 | Providing and fixing SS tower bolt of size 20 cm or above |
| 48 | Providing and fixing bright finished brass tower bolts (barrel type) with necessaryscrews etc. complete:250x10 mm |
| 49 | Providing false ceiling with 12.5mm thick Gypsum moisture resistant board including frames hangers etc complete 2 coats of cement primer etc complete |
| 50 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum moisture resistant board |
| 51 | Painting with acrylic emulsion exterior paint |
| 52 | Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 53 | Miscellaneous labour |
| 54 | Miscellaneous labour for all unforeseen works Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 24, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysNov 25, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 10 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender