Tender For repair maintenance Specialized Electrical And Mechanical Services Installed At Delhi High Court, New Delhi.(Sh:- Replacement Of All Led Light Fitting And Miscellaneous Work At S Block )
Tender Value
98.75 Lakhs
Estimated cost
Bid Submission
18 Nov 2026
5 days left
EMD
1.97 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Delhi → Delhi
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for repair maintenance Specialized Electrical And Mechanical Services Installed At Delhi High Court, New Delhi.(Sh:- Replacement Of All Led Light Fitting And Miscellaneous Work At S Block )
BOQ
| Sl. No. | Item Description |
| 1 | Supplying, installation, Testing & Commissioning of LED surface mounted Batten light of following body material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85% ,Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, Flicker free, (flicker should be below 5 %), life time (LED,Driver & electrical circuitary), of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Embossing/ Engraved/ Screen printing on housing. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved byEngineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C). Powder coated die cast / Extruded aluminium Body (Thickness ≥ 1.20 mm) |
| 2 | 36 watt |
| 3 | Supplying, installation, Testing & Commissioning of LED Recessed/ surface Down lighter (Round/ square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80 , UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below 5%), life time (LED,Driver & electrical circuitary), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends , CCT 3000°K / 4000°K / 5700°K / 6000°K / 6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be confirming to relevant BIS standards and trade mark certificate (T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105and <120 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C)Powder coated die cast /Extruded aluminum Body including trim |
| 4 | 12 -15 watt |
| 5 | 18 watt |
| 6 | 22 watt |
| 7 | Supplying, installation, Testing & Commissioning of Panel light 2x2 ft., of following body material and construction as per IS : 10322 with driver as pethe requirement with Driver efficiency >85%, Operating voltage AC 140- 270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg 1.6 centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED,Driver & electrical circuitry), of minimum 50000 Burning Hours with, 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6000°K / 6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing onhousing. complete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement.(Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C). Powder coated die cast / Extruded aluminium Body (Thickness ≥ 1.20 mm) |
| 8 | 36 watt |
| 9 | Supply and fixing of IP20 5mtr/ roll LED strip for mounting in cove with color temperature 3000K, CRI≥80, efficacy of 104lm/W, SDCM<3, working temperature -20°C to +35°C, supply voltage 24V DC. Aluminium profile & driver have to supply as per the requirement along with accessories. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Both the fixture and Driver should have separate BIS approval. The Fixture will be dali Dimmable. |
| 10 | Supply and fixing of 1’x 4’ recessed LED luminaire with CRCA sheet steel housing, finished with high-quality powder-coated white finish and provided with fully diffused opal cover to ensure uniform, glare-free illumination, including installation, testing and commissioning complete as per CPWD specifications. The luminaire shall be energy efficient with system efficacy greater than 120 lm/W and shall be available in lumen packages of approximately 3600 lumens. The luminaire shall have correlated colour temperature (CCT) options of 4000K/5700K/6500K with colour rendering index (CRI) ≥80 and SDCM <5 for colour consistency. It shall operate on 140–270V AC supply with fixed output LED driver, having THD <10% and surge protection of 4 kV. The luminaire shall be suitable for operation at ambient temperature up to 45°C. The luminaire shall be of CRCA housing construction with serviceability class B and shall have ingress protection rating of IP20 and impact protection IK02. The overall dimensions shall be approximately 1195 mm x 295 mm x 35 mm. The luminaire shall have minimum rated life of 50,000 burning hours (L70B50). The fitting shall conform to relevant BIS standards and LM-79/LM-80 reports. |
| 11 | SITC of 25 W recessed LED linear luminaire with extruded aluminum housing, white powder-coated finish, prismatic diffuser, integral LED driver and SMD LED light source. The aluminaire shall deliver 2750 lumens at 400K/5700K/6500K K CCT, with CRI =≥80, power factor≥0.90, THD less =than 10%, Delivered efficacy of min. 110 lm/W and beam angle of 120°. It shall operate on 140–270 V AC supply, with IP20cprotection, Class I electrical csafety and surge protection upcto 3.0 kV. Rated life shall be L70B50 of 50,000 hours. Dimensions shall be approximately 1132 × 67 × 40 mm (L × W × H), conforming to IS 10322 (Part 5/Sec 2): 2012. |
| 12 | Supply, Installation, testing and commissioning of desktop-style delegate conference microphone unit, supplied complete with a base and detachable gooseneck microphone with Mute/Unmute, unit shall have RJ45/CAT6 connectivity with cardioid or better capsule, sensitivity: 46 dBV/Pa, frequency response: 20 Hz to 20 kHz, input impedance: 2 kΩ, with directional response at 0°/180° greater than 20 dB at 1 kHz, equivalent noise level shall not more than 20 dBA SPL, maximum sound pressure level: 125 dB with signal-to-noise ratio shall be greater than 80 dB, cross talk shall be greater than 80 dB, and total harmonic distortion shall remain below 0.05%. The unit shall be equipped with a 2.4-inch or bigger IPS TFT display and provide audio output through a 3.5 mm earphone jack supporting loads above 10 Ω, with an output power of 10 mW, while the gooseneck microphone shall be 420 mm or more in length with dual adjustment band and lighting indication should be in ON/OFF touch and gooseneck both, unit should have functionality to select services (tea, pen, etc) for requirement in meeting, lighting indication in microphone can be change as per user requirement, with camera tracking function support, etc complete required as per specifications. |
| 13 | Supply, Installation, testing and commssioning of desktop-style chairman conference microphone unit, supplied complete with a base and detachable gooseneck microphone with Mute/Unmute, delegate priority touch and delegate canceling touch functionality, unit shall have RJ45/CAT6 connectivty with cardioid or better capsule, sensitivity: 46 dBV/Pa, frequency response: 20 Hz to 20 kHz, input impedance: 2 kΩ, with directional response at 0°/180° greater than 20 dB at 1 kHz, equivalent noise level shall not more than 20 dBA SPL, maximum sound pressure level: 125 dB with signal-to-noise ratio shall be greater than 80 dB, cross talk shall be greater than 80 dB, and total harmonic distortion shall remain below 0.05%. unit should have option to change the lighting indication of microphone as per client requirement and should have option to send request of services like pen, paper, tea, help, etc, The unit shall be equipped with a 2.4-inch or bigger IPS TFT display and provide audio output through a 3.5 mm earphone jack supporting loads above 10 Ω, with an output power of 10 mW, while the gooseneck microphone shall be 420 mm or more in length with dual adjustment band and lighting indication should be in ON/OFF touch and gooseneck both, unit should have functionality to select services (tea, pen, etc) for requirement in meeting, lighting indication in microphone can be change as per user requirement, and with camera tracking function support, etc complete required as per specifications. |
| 14 | Supply, Installation, testing and commissioning of central control unit, shall operate on AC 100–240V, 50/60Hz power supply and provide a frequency response from 20 Hz to 20 kHz, signal-to-noise ratio shall be greater than 96 dBA and total harmonic distortion shall remain below 0.05%, equipped with one USB recording connector, four or more DIN-8 input connectors, and four or more RJ45 group connectors. It shall include RS-232 (3P) connectors for both central controller and camera switch, Camera control shall be provided through a 6P connector, while computer connectivity shall be available via USB and RJ45. The building alarm integration interface shall consist of two 2P connectors (5V + Audio), Audio input shall be supported through one 2P unbalanced connector and one RCA unbalanced connector and output shall include one 3P balanced connector, two 2P unbalanced connectors, one XLR balanced connector, one 6.35 mm unbalanced connector, one RCA unbalanced connector, one coaxial connector, and one optical fiber connector. The unit shall also incorporate a sound card with USB and RCA (unbalanced ×2) interfaces, shall be built on advanced digital processing with inbuilt digital signal processor for better audio output and transmission technology, fully compliant with IEC60065 international standards with powered by a 1.4 GHz industrial-grade embedded processor with 1 GB memory to ensure high-speed performance and smooth system response system scalability, Touch screen: 4.3-inch or bigger full-view IPS capacitive touch screen, accommodating up to 240 units per host interface and a total system capacity of 76,800 units, with flexible connection methods. Leadership control shall be unlimited, with configurable speaker limits from 1 to 20 and no restrictions for chairman or VIP units with eight intelligent conference modes including FIFO, LIFO, quantity limit, chairman permission, voice activation, timed speech, queuing, and free discussion, ensuring adaptability to diverse meeting styles. Camera integration shall support PELCO-D/P, SONY, SAMSUNG, and other protocols, with tracking, preset positions, RS-232/RS-485 control, and HDMI/SDI matrix switching for cameras, etc complete required as per specifications. |
| 15 | Supply, Installation, Testing & Commissioning of Two way Passive wall mount loudspeaker with LF: 5.25\\" or better, HF : 1\\" or better having Frequency Response (+/-3 dB) : 70Hz - 18 kHz or better, RMS power : 40 W at 100V & 50 W at 8 Ohms or better, Power Taps : 40 W/20 W/ 10 W/ 5 W, Maximum SPL: 104 dB or better, Sensitivity: 87 dB or better, Dispersion : 110 degree X 110 degree or better, Transformer Taps : 100 V/ 70V with OEM mounting arrangement having vertical and horizontal rotation to aim the speaker in any direction. CE Certification or more |
| 16 | Supplying and fixing of Hand Dryer : Casing :SS 304 Grade, BIS & ISI Certified, Hepa Filter, Sensor Range :12–15 CM, Hand Dry Time :Less than 30 seconds, Auto Cut-off :60 seconds, Motor :Brush AC Type, Speed :30,000 RPM, Rated Power :1250 W (Motor 500 W + Heating Element 750 W), Voltage :220–240 V / 50–60 Hz, Protection Class :IPX3, Blowing Volume :>270 m³/h, Air Speed :100 m/s etc complete as required at site. |
| 17 | Supply and replacement of 200 AH, 12 V FR Sealed Maintenance Free (SMF) battery of approved make, suitable for UPS/charger system, on existing battery mounting rack, including dismantling and removal of existing unserviceable battery and credit under buyback, connection, interconnection with existing system, necessary battery terminals/connectors, hardware, testing and commissioning, complete in all respects as required. (With buyback of old batteries) |
| 18 | Credit by back old dismantle |
| 19 | LED Batton (assorted size) |
| 20 | Down lighter |
| 21 | 2X2 LED fitting /1X4”/ 4 inch |
| 22 | LED Strip Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 18, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysNov 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 5 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender