Tender For Maintenance Contract For Civil Works From Mayapuri (Excluding) To Sarojini Nagar (Including) Metro Station Of Line-7 Including Dhaula Kuan Rss.
Tender Value
8.05 Crore
Estimated cost
Bid Submission
30 Nov 2026
17 days left
EMD
2.68 Lakhs
Bank guarantee accepted
Document Fee
23600
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
New Delhi → Delhi
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Maintenance Contract For Civil Works From Mayapuri (Excluding) To Sarojini Nagar (Including) Metro Station Of Line-7 Including Dhaula Kuan Rss.
BOQ
| Sl. No. | Item Description |
| 1 | Total of Schedule-A (DSR 2023 Items) + Schedule-B (NDSR Items) |
| 2 | Total of Schedule-C Manpower |
| 3 | Total of Schedule-A(DSR Civil 2023 Items) |
| 4 | Total of Schedule-B (NDSR Items) |
| 5 | Total of Schedule-C Manpower OCM-2345 APPENDIX- 3A PROFORMA FOR STATEMENT OF MINOR DEVIATIONS (Refer Clause C 2.2(d) and C 15.1 of ITT) 1. The following are the particulars of minor deviations from the requirements of the Tender Document: Sr. No Clause Deviations Price reduction for each deviation/s Note : 1. The Tenderer shall indicate price reduction against each deviation in Appendix-3A of BOQ. This price is the price which the tenderer shall reduce from this tender price if deviation(s) is/are accepted by the Employer. 2. Where there is no deviation, the statement should be returned duly signed with an endorsement indicating ‘No Deviations’. In case, Performa of deviations is not submitted or submitted as blank, it will be construed that the tenderer has not proposed any deviations from tender documents. 3. It shall be noted that in case Nil/Zero/NA Price quoted by Tenderer in Appendix-3A then it shall mean that contractor has quoted same price for deviation and undeviation bid. 4. If the tenderer proposes deviations in tender documents, and/or any other terms and conditions of the tender, other than in this Appendix, it will have no effect. Signature of authorized signatory On behalf of Tenderer OCM-2345 Preamble |
| 6 | The Bill of Quantities shall be read in conjunction with Notice Inviting Tenders, Instructions to Tenderers, General and Special Conditions of Contract, Employer's Requirement and Technical Specification and other relevant documents. |
| 7 | BoQ1 consists of Schedule A (DSR Civil 2023 Items) and Schedule-B (NDSR Items) & Schedule-C (manpower). |
| 8 | The rates and prices to be tendered in the unit Priced Bill of Quantities of Schedule A (DSR Civil 2023 Items) and Schedule-B (NDSR Items) & Schedule-C (manpower) are for completed and finished items of works and complete in all respect. |
| 9 | Tenderers shall quote their offer in Indian Rupees (INR) only. Tenderers are required to be quoted percentage (%) Excess/Less for schedule-A, B & Excess for Schedule- C in figures in the appropriate highlighted cells in the BoQ1 sheet. All the quoted rates will be deemed to include Duties, Taxes, Octroi, Royalty etc., cost of all plants, labour, supervision, materials, transport, all temporary works, erection, maintenance, utility identification, contractor’s profit and establishment/ overheads, together with preparation of design and drawings, all general risks, insurance liabilities, compliance of labour laws and obligations set out or implied in the contracts. For taxes and duties refer clause C2.5 of ITT & clause 10 of SCC. |
| 10 | The price offer in the BOQ shall be given without considering any deviation mentioned in Appendix-3 of FOT i.e. price in the box shall be quoted as per tender conditions without any deviation. |
| 11 | If the tenderer fails to quote rates against any item, the tender may be treated as incomplete and non- responsive and shall be rejected. |
| 12 | Errors will be corrected by the employer for any arithmetical errors in computation or summation as per contract conditions. |
| 13 | The Financial Proposal (as per BOQ) shall be uploaded online on the website http://etenders.gov.in/eprocure/app. The rates shall be quoted in the excel file provided in the bid documents. The tenderer shall download the excel file and quote the rates against each highlighted cells in BoQ1. After quoting their rates the excel file shall be uploaded accordingly. The rates shall not be offered/quoted elsewhere in the technical submission/ tender submission. |
| 14 | The actual work executed against all the BOQ as detailed in tender document would be paid on measurement basis. |
| 15 | The contractor may raise their “On Account” payments on monthly basis as per the status of work on the last day of the respective month as per relevant clause of Employer's Requirement |
| 16 | In case of DSR item the description is given in brief and detailed description of item should be as given in DSR 2023 (Civil) (published by CPWD). Please Enable Macros to View BoQ information DELHI METRO RAIL CORPORATION LIMITED Contract No.: OCM-2345 - “Maintenance Contract for Civil works from Mayapuri (excluding) to Sarojini Nagar (including) Metro Station of Line-7 including Dhaula Kuan RSS” S. No. Item No. Description of items Unit Qty Rate including GST @18% Amount (Rs.) Schedule-A : DSR Civil 2023 DSR-1 Basic rate,Sub head 1,2,3,4,5,6,7,8,9,10,11,12 Lump Sum 16600000.0 DSR-2 Sub head 13,14,15,16,17,18,19,20,21,22,23,24,25,26 Lump Sum 30000000.0 Total of Schedule-A(DSR-2023 Items) (excluding GST) 39491525.42 Total of Schedule-A (DSR-2023 Items) (excluding GST) after applying CPWD factor 0.973 38425254.23 GST on Schedule-A (DSR-2023 Items) @18% 6916545.76 Total of Schedule-A (DSR-2023 Items) (inclusive of all, GST@18%) 45341799.99 Schedule-B : NDSR Items NDSR-1 Hire Charges of Machinery 1.1 Supply of canter on hire charges basis for carriage DG set, pump set etc. of material, shifting of material from here and there as per requirement. For ten hours one shift shall be paid. The rate are inclusive of operator, helper and consumables etc. Nothing shall be paid extra. Each 110.0 1929.76 212273.6 1.2 Hire charges of sky lift (Hydra machine ) of 15 to 20 meter long boom including the cost of diesel, oil, consumables, temporary plastic barricading with safety cones, tricolor blinking lights, caution tape, operator with valid driving licence for heavy vehicle & valid RTA registration of vehicle, maintenance etc. complete in all respect. The skylift shall have third party certification for its safety worthiness, competency and maintenance certificate. Per shift 300.0 7275.43 2182629.0 1929.76 1.3 Providing and Operating Diesel Boom Lift of 25-28 metre reach. Rate shall include diesel charges, one operator with all safety items complete and loading/unloading of man lifter at site. Rate is inclusive of all taxes/levies/cartage/GST, cost of diesel, oil, consumables, temporary plastic barricading with safety cones, tricolor blinking lights, caution tape, operator with valid driving licence for heavy vehicle & valid RTA registration of vehicle, maintenance etc. complete in all respect. The rate shall include provision of traffic marshall and safety equipments like baton light while working at main road. The skylift shall have third party certification for its safety worthiness, competency and maintenance certificate. Per shift 150.0 9948.96 1492344.0 7275.42666666667 1.4 Supply of 10 KV generator set including the cost of diesel and operator etc. as per direction of Engineer- in-charge. Shift of 8 Hrs 100.0 1509.72 150972.0 9948.96 NDSR-2 Reinforced Cement Concrete/Concrete work 1509.71666666667 2.1 Core cutting member of RCC. /Plain CC. of all grades 100 mm dia and 200 mm thick RCC./PCC. work. Each 20.0 1983.86 39677.2 2.2 Core cutting member of RCC. /Plain CC. of all grades 200 mm dia and 150 mm thick RCC./PCC. work. Each 20.0 2021.29 40425.8 1983.86 2.3 Core cutting in RCC 100 mm dia and upto 300 mm depth complete including all man, materials, machine etc. complete Each 20.0 2412.51 48250.2 2021.29 2.4 Providing and fixing in poslition Precast RCC bollards of size 900mm (height) 150 mm vibro compcacted accurately design moulds appropriate reinforced with drawing plastic space and concrete block of mix 1:2:5 and pit size 30*30*30 cm including earthwork excavation etc complete as per direction and instruction of engineer in charge. Each 800.0 943.95 755160.0 2412.50666666667 NDSR-3 Stone Work 943.95 3.1 30 mm thick flamed granite : Providing and laying 30mm thick FLAMED (with 25% - 35% quantity polished as per pattern) Sadarhalli Grey Granite Stone flooring in treads and landings (including bull nosing, rounding the nose and making groove) of steps of approved colour, size and pattern, (sample of granite stone shall be approved by Engineer-in-charge) over 20mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with neat cement slurry mixed with pigment to match the shade of granite stone complete as per specifications and architectural drawings. Sqm 100.0 3729.9 372990.0 3.2 Extra for Red/ Raw Silk/ Tan Brown/ Jet Black granite Sqm 100.0 815.67 81567.0 3729.895 NDSR-4 Cladding Work 815.67 4.0 Dry Stone Cladding- GraniteSupplying, providing and fixing prepolished granite stone work ofup to and including sizes of 1200mm.X600mm of approved colour/pattern with 2mm wide groove all around at all levels for wall linings/columns/skirting (veneer work) by mechanical arrangement with SS cramps/brackets (SS Grade 316), anchor bolts, 5mm vertical SS pins, 65mm long (SS Grade 316) of approved make and inserts as per drawings and specifications. The cost of making necessary grooves all around stone pieces, chamfering of comer edges and polishing are included. Allow for cutting of holes and box outs for se1vices etc. Minimum Compressive strength shall be as per I Sm 1121 (part I) . Water absorption Test shall be carried out as per IS 1124. All Groove for fixing the Cramps to be cut on machine table only or as per direction of Engineer- in-charge 4.1 30 mm thick- mirror polished; Jeera white , Sadarali or euivalent Sqm 100.0 5373.19 537319.0 4.2 Extra for Jet Black, Jcone Brown, Lakha red or Red Silk, Blue Pearl granite Sqm 100.0 565.6 56560.0 5373.19 NDSR-5 Finishing/Repair of Building 565.6 5.1 Micro concrete: Providing and laying of micro concrete for repair of small damaged patches in RCC plinth or track or structure during traffic or non traffic hours. Kg 2000.0 97.23 194460.0 5.2 Providing and laying thick self-levelling epoxy floor coating FORGARD SL or equivalent, in approved color shade & as per manufacturer's specifications, on the concrete floor. The work includes surface preparation with cleaning, grinding by mechanical means and ensuring optimum moisture level in the floor, repairing filing of construction joints/small cracks in concrete floor with epoxy putty made of epoxy and silica powder, applying two components solvent free epoxy raisin based primer, applying 1mm thick three component self levelling epoxy floor coating to give a smooth glossy finish, all complete as per manufacturer's specifications. 97.23 5.2.1 1 mm thick Sqm 200.0 438.03 87606.0 NDSR-6 Rain Water Harvesting & Tubewells/Borewells 438.03 6.1 PVC pipe 160 mm providing and laying 110 mm dia 6 kg pressure PVC pipe for drainage all work complete including all fitings, fixtures socket, bend etc as per site requirement. The payment shall be on runing meter of length basis. The work shall be carried out as per directed by enineer in charge. mtr. 600.0 624.53 374718.0 6.2 Removal of water and existing filter material of old rain water harvesters, development and cleaning of bore, cleaning of material and putting back to the system including replacing the non usable filter media with new one (cost of new filter media will be paid under the corresponding DSR item). Each 80.0 39314.26 3145140.8 624.53 6.3 Supply 5-7.5 HP submersible pump of discharge capacity 50-60 kl/hrs including cost of operation etc. complete. Shift of 8 hrs 200.0 3256.4 651280.0 39314.2566666667 NDSR-7 Road Work 3256.40333333333 7.1 Retro reflective sheet : Providing and fixing of 2 mm thick SRBG/aluminium sheet cautionary retro reflective sheet on RCC pier with all T&P, staging, destaging fasteners, manpower, PPE's etc. all complete and as per direction of engineer in charge SQM 250.0 5866.95 1466737.5 7.2 Providing safety and traffic diversion arrangement at the location of work with two stage protection that is with Concrete barriers and PVC drum filled with Sand/Water. The item shall include transportation and placing in position of concrete barriers (06 nos. concrete barriers of size 2.5-3m (length) and 1.2 m height) and suitable nos. of drums as per approved plan and direction of Engineer-in-charge. The concrete barriers will be provided by DMRC (which will be required to be lifted by contractor from any DMRC site within NCR), whereas all other materials are to be provided by contractor. The item shall include all labour/material cost for filling of drums, providing reflective lights, reflective tapes, caution tapes, 02 nos. marshals for traffic diversion and any other miscellaneous item(s). The marshals shall remain available from the start of work at the location, till the location is cleared completely of all men and material. On completion of work, concrete barriers will have to be returned to DMRC and placed as per directed location. Nothing shall be paid extra for all the works described in this item. EACH LOCATION 100.0 15034.01 1503401.0 5866.95333333333 NDSR-8 & 9 Sanitary Installation, Water Supply & Drainage, Plumbing items 15034.0133333333 8.1 Providing and fixing of bulk type water meter class B flanged type with CI body with dry dial type & Magnetic drive make Kranti or equivalent confirming to IS 2373. The rates include all cost of material, labour, transportation, tools & plants all height, taxes etc as per direction of engineer in charge. 8.1.1 40mm Each 10.0 7579.32 75793.2 8.1.2 50mm Each 40.0 8273.0 330920.0 7579.32 8.1.3 65mm Each 10.0 12287.0 122870.0 8273.0 8.1.4 80mm Each 10.0 12287.0 122870.0 12287.0 9.1 Providing and fixing C.P. brass towel rail 24\\" as per approved make. Nos 50.0 1009.45 50472.5 12287.0 9.2 Providing and fixing, ABS plastic body liquid soap dispenser with push lever assembly complete with soap refill as per approved make. Nos 50.0 1059.92 52996.0 1009.45 9.3 Providing & fixing S.S. body tissue paper dispenser complete including cutting and making good the walls wherever required. Make: Kohler/Euronics/Hindware or equivalent Nos 20.0 5371.38 107427.6 1059.92 9.4 Providing & fixing Health faucet with 1 metre long Flexible Tube and CP wall hook with PVC & SS Screws including cutting and making good the wall wherever required complete as directed by the Engineer in-charge (IGBC Compliant 1.5 LPM at design water pressure 3 bar). Make: Jaquar/Kohler/Hindware or equivalent Nos 100.0 1613.01 161301.0 5371.38 9.5 Providing & fixing SS Gab bar for wash basin fixed on wall for Handicapped Toilet with fasteners/SS Screws incluting cutting & making good the wall complete in all respect and as per direction of the engineer in-charge. Make: Jaquar/Panyware/Hindware/Cera or equivalent Nos 10.0 11592.07 115920.7 1613.01 9.6 Providing & fixing CP Hinged Anns (Sliding rail) for Handicapped Toilet with SS Screws over Rawl Plugs complete as per instructions of the engineer-in-charge. Make: Jaquar/Panyware/Hindware/Cera or equivalent Nos 10.0 9698.29 96982.9 11592.07 9.7 Providing and fixing Diaper change station model no. EDC-012N, make Euronics, complete in all respects and as per direction of Engineer-in charge Each 10.0 23791.62 237916.2 9698.29 9.8 Providing and fixing of CP brass twin coat hooks (Jaguar Cat no. 1161 or equivalent) fixing on door with C.P brass screw complete in all respects and as per direction of Engineer-in charge Each 50.0 294.82 14741.0 23791.62 9.9 Providing and fixing clean out plug for 100 mm dia model no. COS0S SS Finish MATT complete in all respects and as per direction of Engineer-in charge Each 50.0 955.98 47799.0 294.82 9.1 Providing and fixing automatic sensor faucet for cold water, for wash basin complete in all respect including basin mounted auto tap, with infrared sensors with solenoid valves for cold water with electronic circuit and necessary accessories including cutting and making good the walls and floors as per requirement at site. Maximum flow required. 2 LPM. Fixture to be taken as IGBC approved or approved by Engineer-in-charge/Architect Incharge Nos. 20.0 8929.19 178583.8 955.98 9.11 Providing and fixing. Metallic Body liquid soap dispenser with push lever assembly complete with soap refill. Make: Jaguar, Cat No.ACN-1137N , complete in respect and as per direction of Engineer-in-charge Nos. 20.0 3327.12 66542.4 8929.19 9.12 Supply, Fixing solid state, no touch operting, fully hygienic hand drier (Jaquar - HDR-SAP-M99ACS) of approved shade with single blower, with time delay, summer & winter control, music while d1ying, volume ON/OFF controls including providing necessary brackets, cable from drier to Plug, Plug top key and lock etc, complete as required. Nos. 10.0 21713.58 217135.8 3327.12 9.13 Providing & fixing Toilet Cubicle (of following standard dimension which includes 600mm door size width) made of heat, bacteria, water, chemical, scratch,impact and anti bacterial resistant 12mm thick high pressure laminate panels tested in approved laboratory. Finish of the compact laminate should be Suede,Raw silk model includes doors, pilasters & intennediate panels finished with approved texture/shade as per the detail drawings & as per IS 2046 (Indian Standard) and as per fire retardant BS-476/97 standard. This also includes providing and fixing in position necessary hardware made out of Stainless steel (Grade 304) as per manufacturer's specifications & Architects instructions like ( I) Door Knob, (2) Gravity Hinges, (3) Thumb tum lockset with Occupancy indicators, (4) Coat hooks with Door stopper (5) U- Channels, (6) Adjustable foot/pedestal, (7) Top rail (8) Rubber noise deafening tape, (9) Screws & wall Plugs. All screws will of 304 Grade in stainless steel with satin finish. All pilasters are supported by stainless steel Bottom Cladding.The base of the stainless steel bottom cladding will be anchored to the floor with a clearance height upto 150mm. The top fitting should consist ofSS top rail which will get fixed with pilasters. SS wall fixing is used only on the wall which will hold the ss top rail 21713.58 9.13.1 Toilet Cubicle with standard dimension of 2000-2100mm Height x 1000mm Width x 1550mm Depth, which includes 600mm door size width as per drawing, however in case of change nothing shall be paid extra). Nos 10.0 38257.27 382572.7 9.14 Providing and fixing Urinal partition made of 12 mm thick compact laminate total height 1195 mm, Depth 450-500mm, Gap from ground 500 to 600 mm (as per drawing) and fixingToilet UMP (urinal modesty panel) made up of thermosetting resign treated high pressure, self supporting decorative compact laminates with permanently incorporate anti-bacterial agents(under JIS Z2801:2000 ce11ification) during manufacturing. Compact board should beresistance to water immersion through permissible increase on thickness and mass <0.60%and board density > J.35kg/cm3 and fulfilled the criteria of green guard gold certification andmanufactured under EN438-2&3:2005 standard. 12mm thick compact board should be Moisture resistant, Impact resistant, termite resistant, Scratch resistant ,Weather and climatic shock resistant. Finish of compact laminates should be suede finish which includes door,pilasters and intermediate panels finished with approved texture/shades as per 1S2046 and fulfilled the criteria of fire retardant under BS-476/97 and EN438-6 with classification of BS ID0 standard. Screw & wall plugs should be approved under the instruction ofEngineer-incharge. 38257.27 9.14.1 i) All screw will of 304 grade in SS with stain finish. All pilasters are supported by SS bottom cladding. Stainless steel L clamp is used to attach the divider to the wall, stainless steel L clamp hardware fittings along with SS 304 screws are used to fix the Urinal partitions on the wall. Nos 50.0 5241.25 262062.5 9.15 Drain cleaning: Cleaning of chocked drains including removing of covers, cleaning of silt, mud, rubbish etc and refixing of top cover. All work complete including removing and disposal of silt as per direction of Engineer- In-charge for size width (500 to 1000 mm) depth upto 600 to 1200 mm. mtr. 3000.0 158.02 474060.0 5241.25 9.16 Drain cleaning: Cleaning of choked drains including removing of covers, cleaning of silt, mud, rubbish etc and refixing of top cover. All work complete including removing and disposal of silt as per direction of Engineer- In-charge for size width (300to 450 mm) depth upto 500 mm. mtr. 3000.0 97.86 293580.0 158.02 9.17 Cleaning of under ground water tank of all the section/capacity of tank by emptying of water in other tank or in a separate storage device to avoid wastage of water. The rate are inclusive of all taxes man, material, safety equipment and other required resources. Nothing shall be paid extra and work shall be carried out as per direction of Engineer- In-Charg. The tank shall be cleaned on half yearly basis i.e. two times in a year and report shall be submitted to DMRC. Per Tank 80.0 9749.12 779929.6 97.8566666666667 NDSR-10 Repairing and maintenance of existing rolling shutters : 9749.12333333333 10.1 Oiling and greasing of shutters:Oiling and greasing of rolling shutter with H.P.equipment greasing including complete cleaning of oil and scrapping of grease including labours and materials during night time as per direction of Engineer-In-Charge. For rolling shutter up to 4.5 m height. Each 300.0 889.59 266877.0 10.2 Providing hardware or other parts for smooth functioning of rolling shutters items will be supplied as per CPWD specifications. 889.59 10.2.1 Brackets(sides) Each 100.0 381.74 38174.0 10.2.2 Wire spring Each 100.0 534.42 53442.0 381.736666666667 10.2.3 Spring holder Each 100.0 190.88 19088.0 534.42 10.2.4 MS. Gararee device. Each 100.0 1526.93 152693.0 190.88 10.2.5 Gear box. Each 100.0 3817.31 381731.0 1526.93 10.2.6 Rolling shutter handle. Each 100.0 229.05 22905.0 3817.30666666667 10.2.7 Locking Naka/kundee including welding. Each 100.0 76.35 7635.0 229.046666666667 10.2.8 Ball bearing. Each 100.0 229.05 22905.0 76.35 10.2.9 Gararee rod. Each 100.0 916.16 91616.0 229.046666666667 10.2.10 MS. Top cover. mtr. 100.0 375.68 37568.0 916.156666666667 10.2.11 Bottom locking rail. mtr. 100.0 626.13 62613.0 375.68 10.2.12 MS. Lath. mtr. 100.0 100.19 10019.0 626.13 10.2.13 MS. Pipe shaft 2\\" dia. mtr. 100.0 375.71 37571.0 100.186666666667 10.2.14 Side guide rail mtr. 100.0 250.46 25046.0 375.71 10.2.15 M.S. Grill. For ( existing pattern ) Sq. m. 100.0 2052.94 205294.0 250.463333333333 10.2.16 Rolling shutter lever lock. Each 100.0 1449.84 144984.0 2052.93666666667 NDSR-11 Steel Work 1449.84 11.1 Polishing and buffing of SS 304 railing/ SS surface of provided in metro stations with minor grinding ( as required) and removing stains/blemish with proper rubbing and polishing. The surface with suiatable material & finally buffing the surface with high speed buffing machine using buffing mterial as per direction of Engineer-in-charge. The work will be carried out in non revenue hours and rates are inclusive of all taxes, man power, material, tools and plants, CO and OH etc all complete. Sqm. 2500.0 417.31 1043275.0 11.2 Providing and pasting stainless steel of 304 grade name plate (12\\"x4' ) (as per DMRC approved list) as per direction of engineer- in- charge. Each 100.0 325.02 32502.0 417.31 11.3 Glass door locking arrangement: Providing and fixing 6 lever/pin cylinder mortice cylinder/latch set Complete with door srtike/lever handle/screw etc. (as per DMRC approved list) complete in stainless steel or approved glazed door etc. including all fixing and othr accessories as required maufacture for the on pannel/solid and and as per drawing/ specification and as directed complete. Each 100.0 385.29 38529.0 325.02 NDSR-12 Roofing/poly carbonate Sheet 385.29 12.1 Providing and fixing 10 mm thick poly corbonate sheet make GE or equivalent and make confirming to IS 14443:1987) of required colour, fasteners, silicon sealent, EPDM gaskets and shade including self drilling/self taping screw as per requirement. Sqm 200.0 1622.2 324440.0 12.2 Providing, supplying, erecting and fixing in position 3 mm thick poly corbonate sheet of approved color and texture. Cost to include jointing, sealing with butul adhesive and tape etc as per manufactures specification and cover all cost of labours tools, plants, temporary works. etc. all complete. Sqm 200.0 864.42 172884.0 1622.195 12.3 Providing and fixing single skin Hi-rib Profiled sheeting 930-1020 mm cover width 28-30 mm crests @ 186-333 mm c/c manufactured out of 0.45 mm BMT ( base metal thickness) Hi-tensile galvalume/zinclume steel sheets shall have wide pans with 2-3 nos. stiffning ribs for effective water shedding and special male/female ends with full return legs on side laps for purlin supports on both surfaces including side and end caps.(Roof of buildings) Sqm. 100.0 819.73 81973.0 864.415 12.4 Polycarbonate sheet: Providing and fixing of leak proof fire resistance and UV resistance at all height of Lexan compact clear sheet of 5mm thick GE plastic or approved equivalant make confirming to IS14443-1987 the rates i.e the cost of fasteners silicon sealent, EPDM gasket and all other ancillary works as required for completion of work as per Engineer- in- charge are inclusive. Sqm. 100.0 2947.61 294761.0 819.73 12.5 Providing and fixing of Anti Birds Spikes made of high quality of Poly Carbonate, 5 Row 304mm. Rates are inclusive of screws, cable ties, adhesives, fasteners up to 5 meter Height complete as per direction of Engineer-in-Charge. RMT 500.0 290.9 145450.0 2947.605 NDSR-13 Aluminium Work 290.896666666667 13.1 Designing, Providing, Fabrication and Erection of extruded Aluminium fixed Louvers / aerofoil sections of approved shade and color powder coated (minimum thickness of coating 55 microns) with extrnded Aluminium subframe, extrnded built up standard eliptical sections conforming to IS : 733 and IS : 1285 fixed with raw plugs and stainless steel screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/ neoprene felt complete in all respect. Aluminium sections shall be smooth, rust free, straight, as per architectmal drawings and the directions of Enginner-in-charge etc.All structural steel support frame work shall be paid separately as per DSR Civil 2023 item. Kg 100.0 565.82 56582.0 NDSR-14 Glazing Work 565.82 14.1 Providing and fixing in position laminated toughened glass of 13.52 mm (6mm+1.52PVB+6mm)thickness at various location in ticket counter window of SCR door of EFO wall of EFO rooms including the cost of filling gap with clear/coloured sealent of approved make and brand etc. complete and as per site requirement (as per DMRC approved list). Sqm 500.0 3321.29 1660643.33 14.2 Providing and fixing 6 mm thick toughened glass (as per DMRC approved list) in existing frame subframe with EPDM rubber gasket silicon sealent and necessary pressure clip as and where required.The rate quoted shall be inclusive of fixing and grinding corners and required hole etc all complete and all taxes etc .The contractor shall visit the site and take exact measerement of size in which glass is to be provided at various location. Sqm 100.0 1677.46 167746.0 3321.28666666667 14.3 Providing and fixing 10 mm thick toughened glass (as per DMRC approved list) in existing frame subframe with EPDM rubber gasket silicon sealent and necessary pressure clip as and where required.The rate quoted shall be inclusive of fixing and grinding corners and required hole etc all complete and all taxes etc .The contractor shall visit the site and take exact measurement of size in which glass is to be provided at various location. Sqm 100.0 2082.76 208276.0 1677.46 14.4 Providing and pasting sun film of approved make (as per DMRC approved list) as per direction of engineer- in- charge. Sqm. 50.0 219.73 10986.5 2082.76 14.5 Providing and pasting froasted film of approved make (as per DMRC approved list) as per direction of engineer- in- charge. Sqm. 50.0 420.82 21041.0 219.73 14.6 Providing and fixing Mac vertical /Regular blind /100 mm including removing, refixing, cartage as per direction of Engineer-In-Charge. Sqm 50.0 1144.21 57210.5 420.82 14.7 Providing and fixing of floor spring for glass door (make Ozone, Dorma etc. or equivalent up to 150 Kg capacity) complete as per direction of engineer in charge Each 100.0 6989.65 698965.33 1144.21 14.8 Digital ultraviolet printing over glass/SS sandwhich panel/metal sheets/tiles etc. designed as desired and using original UV 8 color inks with 29 picolitre SPECTRA Galaxy print head or equivalent, Double deposition of ink, on fixed vacume table of size bigger than 2500 X 1500 for precision holding of glass/metal sheet etc. including the cost of transportation, loading and unloading etc. complete as per architectural drawing and direction of engineer in charge. Printing shall be smooth/textured face directed. Sqm 100.0 1651.02 165101.67 6989.65333333333 NDSR-15 Other Miscellaneous items 1651.01666666667 15.1 (A) Supply and installation of 1200 mm dia TO mirror at Platform level in block hours as per the approved drawing and instruction of engineer in charge including @ Providing and fixing MS frame work (including painting) for the installation of 1200 mm dia TO mirror as per approved drawing and instruction of engineer in charge,(B) Providing and fixing of SS clamp 3 mm thickness with all necessary bolting screwing etc for the installation of 1200 mm dia TO mirror as per approved drawing and instruction of engineer in charge.(C) Removing and disposal of old mirror and frame as per the instruction of the engineer in charge lead upto 50 mtr.(D) Fixing of TO mirror frame with the exiting roof structure with clamping fastner etc. including all as per the approved drawing and instruction of engineer in charge. Each 20.0 34958.81 699176.2 15.2 GI Sheet tray: Supplying,fabricating,fitting & fixing of GI sheet 18 SWG sheet tray fixing with dash fastner of 100x100 mm with the help of supporting MS flat clamp 50x4 mm and clamp will be fixed on beam by desh fastner Tray will be made/fabricated by the way of rivets NUt/bolts m-seal sealent throughly provided to make the join of tray perfect water proof, rate are inclusive of all tools and plants such as cutter welding set power hammer driller drilling machine etc scaffolding transportation of materials to the site of work and rate also inclusive of all skilled and unskilled labours. Work shall be carried out as per direction of Engineer. Rate are also inclusive of all lead lift ascent and descent etc. complete as per instruction of Engineer-In-Charge. Sqm 100.0 1555.17 155517.33 34958.81 15.3 Weathering of granite stone by flaming of thermaling with the application of high temperature to the surface of stone to prevent slipping of commuters. This item is inclusive of all manpower, materials, tools, overhead and taxes etc. The work is to be primarily done during non-revenue (night) hours. Nothing extra shall be payble on this account. Sqm 1000.0 229.19 229185.0 1555.17333333333 15.4 Providing fixing on wall face unplasticised rigid PVC rain water pipes (working pressure 6 kg/cm^2) conforming to IS:13592 Type:A including jointing with seal ring conforming to IS:5382, leaving 10 mm gap for thermal expansion.(i) Single socketed pipes 229.185 15.4.1 200 mm diameter Mtr 800.0 1751.06 1400845.33 15.5 Providing fixing on wall face unplasticised PVC moulded fittings/accessories for unplasticised PVC rain water pipes (working pressure 6 kg/cm^2) conforming to IS:13592 Type:A including jointing with seal ring conforming to IS:5382, leaving 10 mm gap for thermal expansion. 1751.05666666667 15.5.1 200 mm x 100 mm Dia, Reducer Tee Each 100.0 1910.97 191097.33 15.5.2 200 mm x 200 mm Dia, Bend Each 300.0 687.63 206290.0 1910.97333333333 15.6 Providing and laying Cobble stone of approved size 100 mm x 100 mm x 75 mm of approved colour / Black over 30 mm thick compacted bed cement mortar 1 :4 ( 1 cement :4 coarse sand) along with grouting with cement mortar 1 :2 ( 1 cement : 2 comse sand) complete as per direction of Engineer lncharge. Sqm 20.0 2912.55 58251.0 687.633333333333 15.7 Providing & Fixing of Glass Reinforced Concrete (G.R.C) JaJi 40mm thick in approved size, pattern, design, thickness and color to be fixed on/between RCC/Block work Column or Structural Steel work with 'Dry fixing' method with Stainless Steel (SS - 304) 'L' shaped Clamps, dash fasteners and pins including anchoring, lifting, scaffolding etc. complete as per architectural drawing and manufacture specification. The Screens should be made from '53 h'Tade' White Portland Cement manufactured by 'JK Cement' or equivalent, Quartz, Fine Silica Sand, Alkali Resistant Glass Fiber manufactured by 'Saint Gobain' or equivalent, Super Plasticizers manufactured by 'BASF' or equivalent, Polymers manufactured by 'BASF' or equivalent and U.V resistant Synthetic inorganic pigments should be used for pigmentation manufactured by 'BA YFERROX (Germany)' or equivalent. The material casting should take place in Synthetic Rubber / FRP Mould manufactured by 'Reckli' or equivalent. (All appropriate supporting strucn1re steel work shall be paid extra as per DSR item no 10.25/10.26) Sqm 100.0 4135.59 413559.0 2912.55 15.8 Supplying, Providing & fixing in position baffle ceiling system comprising of closed box shaped profiles. Metal bames shall be made out of 0.50 mm thick hot dipped galvanized steel mate1ial in lengths ofup to 4000mm. The Coil should be stove enamelled on acontinuous application for pre- treatment. The coils to go through 4 stages of pre-treatment, three times oven baked through conversion coating, priming and finish coat ensuring superior adhesion, high corrosion resistance and good colour stability. The coils to be painted on both sides after degreasing. Inside surface to have a primer of 5 microns and a coat of natural colour of 5 microns, exposed smface to have a primer of 5 microns. binder of 5 microns and topcoat of approved colour of 15 microns. Bame Ceiling shall be mounted on slotted galvanized steel grid profile of minimum 2mm thickness in a module of225 mm. Baffle grid shall be suspended and supported by means of minimum 6mm/8mm/12mm dia (suitable for guarantee of stability) threaded suspenders at a distance of 150mm from the edge and 1200mm c/c maximum spacing. Bame fixing brackets shall be used to keep the ceiling in correct place for the leveling purpose. Metal baffles shall be coil coated in desired colour.Bame ceiling shall be installed as per manufacturers technical specification 0.0 0.0 4135.59 15.8.1 Size- 25mm x 200mm (25nun Width & 200mm Height) Sqm 60.0 3984.6 239076.0 0.0 15.9 Supply and fixing factory made solid 25mm thick WPC panel (Wood Polymer Composite) of approved design as per the dimensions provided. WPC is composed of rice and wheat husk with thermo plastic single extruded. which should he termite proof, water proof, fire retardant (Grade A) and Scrcwable having 1400 N scrcw holding capacity on the face and 1100N on edge. of approved make with UV stabilizers. which makes it 100% exterior grade. Material to be of density 550 kgs/cum. The WPC panel shall he fixed on metal frame work (metal frame work shall be paid separately under relavent item head) wilh aluminium clamps/studs/rivets/bolts ofsuitable size as per manufacturer's specification. The contractor shall get the sample approved from competent authority prior to start of execution. Rate are inclusive of all labour, tool & plant, machineries, work at any height and complete in all respects and as per direction of Engineer-in-charge. 0.0 0.0 3984.6 15.9.1 for WPC panel 25mm thick with or without CNC cutting, Coloured Exterior grade Sqm 40.0 4800.66 192026.4 0.0 15.1 Providing and fixing 6mm thick exterior grade High Pressure Laminates (HPL) wall cladding of approved brand with open grooves for linear as well as curvilinear portions of the buildiing for all heights and levels conforming to BS-476/97 and EN438 standard. The HPL cladding lo he fixed tm extruded aluminium framing with the help of angle cleats mcludmg weather sealents and stainless steel screws. Extruded aluminium section shall he fixed @600mm C/C with the help of brackcts and fasteners as per architectural drawing and as per direclion of Engineer-in-Charge. Only the actual area on the external face of the curtain wall with High Pressure Laminates (HPL) panel cladding (including width of groove) shall be measured upto two decimal places. Rates are inclusive of all lahour, tool & plant machincneries. work at any height and complete in all respects and as per direction of Engineer-in-charge. Sqm 40.0 5169.9 206796.0 4800.66 15.10.1 Extra for CNC cutting in HPL sheet as per architectural drawing Sqm 40.0 1334.87 53394.8 5169.9 Total of Schedule-B (Inclusive of 18% GST) Rs. 28391729.72 1334.87 Total of Schedule-B (Exclusive of GST@18%) 24060787.9 GST Amount @ 18.00% 4330941.82 Total Amount of Schedule-B : NDSR Items (Inclusive of 18% GST) Rs. 28391729.72 Schedule C : Manpower items NDSR-16 Providing Plumber/fitter/mason/carpentor for plumbing/sewerage/ rectification/ carpentory/masonary work with all required T&P as per direction of Engineer-In-charge.The payment shall be made on attendance basis and reporting shall be made to Engineer-In-charge. Per Day 1250.0 1456.36 1820450.0 NDSR-17 Providing welder/fitter for welding works along with welding machine to carry out welding work in Line-7 as per direction of Engineer-In-charge including cost of consumable ,T&P etc (electrodes). The payment shal be made on attendance basis and reporting shall be made to engineer-In-Charge. Per Day 600.0 1456.36 873816.0 NDSR-18 Providing unskilled labours /helper/beldar as per direction of Engineer-In-charge with all tools and plants.The payment shall be made on attendance basis and reporting shall be made to Engineer-in-charge. Per Day 3000.0 1210.74 3632220.0 NDSR-19 Deployment of Highly Skilled Labours as Supervisor for 8 Hrs for Miscellaneous works with all required T&P as per direction of Engineer-In-charge.The payment shall be made on attendance basis and reporting shall be made to Engineer-In-charge. Per Day 100.0 1573.06 157306.0 NDSR-20 Supply of Engineer/Supervisor/Surveyor (Highly skilled category of worker) by agency to assist DMRC engineers for inspection, measurement and other miscellaneous works in Line-7 of DMRC Network. The payment shall be made on attendance basis and reporting Per Day 100.0 1573.06 157306.0 NDSR-21 Supply of Skilled Helper (Skilled/Clerical category of worker) by agency to assist DMRC engineers for inspection, measurement and other miscellaneous works in Line-7 of DMRC Network. The payment shall be made on attendance basis and reporting shall be ma Per Day 100.0 1456.36 145636.0 Total of Schedule-C (Inclusive of 18% GST) Rs. 6786734.0 Total of Schedule-C (Exclusive of GST@18%) 5751469.49 5751469.49 GST Amount @ 18.00% 1035264.51 Total of Schedule C : Manpower items (Inclusive of 18% GST) Rs. 6786734.0 Gross Total of Schedule-A + Schedule-B + Schedule-C exclusive of GST@18% 68237511.62 GST Amount @ 18.00% 12282752.09 Gross Total of Schedule-A + Schedule-B + Schedule-C (inclusive of GST ) 80520263.71 4.0 |
AI Tender Summary
Tender Timeline
Nov 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 30, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysDec 01, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 18 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender