Tender For Construction Of Bulk Gas Storage Shed Including Roads, Drains, Boundary Wall, Fencing Etc. For Rapp-7&8.
Tender Value
2.92 Crore
Estimated cost
Bid Submission
01 Dec 2026
10 days left
EMD
5.85 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chittorgarh → Rajasthan
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Bulk Gas Storage Shed Including Roads, Drains, Boundary Wall, Fencing Etc. For Rapp-7&8.
BOQ
| Sl. No. | Item Description |
| 1 | Site Clearance: Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m as per direction of EIC. |
| 2 | Earthwork in excavation in all types of ground substrata consisting of hard rock / fragmented rock / soft rock / ordinary soils / filled up ground / murrum requiring use of rock breaker, drilling, chiselling with mechanical / manual means etc. up to a required depth from the original ground level and dewatering if required for foundation of walls, columns, platforms, Tree pits etc. including backfilling with selected excavated materials in plinth and foundation trenches in layers not exceeding 200 mm thick, watering ramming etc. complete and disposing off the surplus materials to a maximum radially measured lead of 1.0 KM. as per drawings, design , safety and specifications and directions of the Engineer. Note :- Bidders should essentially visit and inspect the construction sites and determine themselves the right and safest method/s of excavation considering the safety of nearby structures and population, before quoting their item rates (Blasting is not permitted). |
| 3 | Up to depth of 1.5m |
| 4 | Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift |
| 5 | Providing and laying 150 mm to 230 mm thick stone soling under floors properly hand packed, filling interstices with spalls, gravels and inert fine material and consolidating to required gradient and camber, spreading, watering etc. complete as per drawings, specifications and direction of Engineer. |
| 6 | Providing and laying in position site batched design mix cement concrete for PCC/RCC work; using coarse aggregate of maximum size not exceeding 20 mm and fine aggregate derived from natural sources, portland pozzolana/ordinary portland /portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. |
| 7 | Plain cement concrete of M15 grade with minimum cement content of 240 kg /cum |
| 8 | RCC of M25 grade with minimum cement content of 330 kg /cum |
| 9 | Providing and laying in position cement concrete of 1:1.5:3 (1 Cement: 1.5 coarse Sand : 3 Graded Stone aggregate 20 mm nominal size) - up to plinth level , transporting of concrete to site, laying, consolidation, finishing, curing etc. all complete excluding cost of centering & shuttering, as per direction of Engineer-in-charge. |
| 10 | Reinforcement: Providing and laying Thermo-Mechanically Treated reinforcement bars of grade as specified in drawings/specifications and as directed by engineer conforming to IS : 1786 latest revision or the latest relevant code for RCC work including straightening, cutting, bending, placing in position and binding with 20 gauge annealed binding wire and cement mortar cover block of all size in C.M. 1:2 MIX or any combination of any suitable material by the approval of EIC, all complete- as per drawings , specifications & direction of engineer in charge. Rate shall be inclusive of equipment, labour, tools & tackles,etc. |
| 11 | Structural steel work riveted, bolted or welded in built up sections, trusses and frame work M.S. door & fix ventilators, anchors etc made out M.S. angle, channels, flats, rods, bars, weld mesh, M.S. pipe etc including supplying, cutting, hoisting, fixing in position and applying two coat of approved quality synthetic enamel paint over a priming coat of approved steel primer all complete as per standard design, including the cost of all material and labour complete- as per drawings , specifications & direction of engineer in charge. |
| 12 | Providing & Fixing of Welded Mesh of different sizes and guage like 6 mm x 6 mm size / 10mmx10mm / 25mmx25mm / 50mm x 50mm or as Directed by the Engineer-in-Charge. |
| 13 | Providing and fixing ISI marked oxidised M.S. sliding door bolts of 16mm dia and 300mm long with nuts and screws etc. complete (Copper oxidised as per IS 1378) as Directed by the Engineer-in-Charge. |
| 14 | Providing & Fixing of M.S. Nickel Chromium \\"D\\" Heavy quality Door Handle of 125 mm Long as Directed by the Engineer-in-Charge. |
| 15 | Providing & Fixing of M.S. Oxidized Butt Hinges of 75 mm (14 Gauge) size size with necessary screws etc., as Directed by the Engineer-in-Charge. |
| 16 | RR Masonry: Providing & laying Random Rubble masonry with hard stone in foundation and plinth level of building & upto 3.00 Mtr. height from NGL for boundary/compound wall with Cement mortar 1:6 (1 Cement :6 Coarse sand) including cost of labour, materials, curing, raking out the joints , finishing, scaffoldings etc. all complete as per drawing, specifications and direction of Engineer in charge. |
| 17 | Providing and laying 225 mm thick R.R. stone pitching including preparation of bed in proper slope and spreading locally available earth over pitching to fill up the gaps as binding material etc. all complete as per drawings, specifications and direction of Engineer. |
| 18 | Pointing on stone work with cement mortar 1:3 (1 cement :3 coarse sand): Raised and cut pointing including finishing, curing, scaffoldings etc. complete at all height as per direction of Engineer-in-charge. |
| 19 | Providing and laying 15mm thick cement plaster 1:4 (1 cement : 4 sand) in single coat on either side of single or half brick wall for interior plastering at all levels using galvanized M.S. wire of I.S. gauge designation 26 s.w.g. chicken mesh over junctions of brick work, beams and column as required including necessary grooves at the junction of RCC and brick work, arises, internal rounded angles, chamfers and / or rounded angles not exceeding 80mm in girth including scafolding, finishing, curing etc all complete as per specifications and direction of engineer in-charge. |
| 20 | Providing and laying 20 mm thick cement plaster of mix :- 1:4 (1 cement : 4 coarse sand ) including finishing, curing, scaffoldings etc. complete at all height as per direction of Engineer-in-charge. |
| 21 | Providing, applying and painting with premium acrylic emulsion paint of interior grade, having VOC content less than 50 g/litre, of approved brand and manufacture, on walls, columns, beams and ceilings, including surface preparation, filling of cracks, sanding, application of primer/putty where required, and two or more coats to achieve even shade and colour complete as per direction of Engineer-in-Charge. |
| 22 | Providing and applying white cement based wall putty (two coats) as approved by ENC including base coat of alkaline resistance cement primer over cement plaster/ concrete surfaces after cleaning / scrubbing of the surfaces with wire brushes, soft brushes, sand papers, steel sheet scrappers and mechanical grinder etc. for removing all kind of burrs, imperfections, undulations and other such defects existing in the surface to achieve plain & even surface. including the cost of materials, labour etc. all complete as per direction of Engineer-in-Charge. |
| 23 | Supplying and applying of approved brand Acrylic Distemper paint (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour as per relevant IS & approved by ENC in Two coat on surfaces of walls, columns, ceiling etc. after cleaning / scrubbing of surfaces with wire brushes, soft brushes & sand paper includingcleaning of area after painting etc, complete as per direction of Engineer-in-Charge. |
| 24 | Providing and laying clay Fly-ash brick masonry using Fly-ash building bricks of class designation- 7.5 ( IS-12894 -latest revision ) in cement mortar 1:6 ( 1 cement : 6 coarse sand) in superstructure above plinth level up to floor five level as per specifications and direction of Engineer including cost of labour, materials, curing, finishing, scaffoldings etc. all complete as per drawings, specifications and direction of Engineer in charge. |
| 25 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50mm (base metal of minimum 0.45mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 26 | Providing and Application of IRONITE NO.3 powder (Metallic Dry shake natural cement colour) @ 6 Kgs/m2 sprinkled over green concrete with 1/3rd of the dry shake to be sprinkled in First pass and floated with Power float, remaining 2/3rd of dry shake to be sprinkled in next pass and the floor laid floated & trowelled to acquire desired finish. |
| 27 | Providing & laying cement concrete 1:2:4 (1 cement : 2 coarse sand :4 graded stone aggregate of approved size) in 50mm average thickness for required location as directed by ENC and stilt flooring laid in suitable panels including Supply & Fixing of 40 mm x 4 mm glass strip in specified grid pattern in line and level including cost of shuttering, compaction, finishing and curing etc. all complete as per drawings, specifications and direction of engineer in charge. |
| 28 | Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion joints in roads / pavements all complete as per direction of the Engineer-in-Charge. Using grade ‘A’ sealing compound conforming to IS: 1834. For expansion joints of size 25mm X 25mm |
| 29 | Providing and fixing on wall face / embedded in ground un plasticized Rigid PVC Rain water pipes of 110 mm dia. as approved by ENC & conforming to IS:13592 type A (4 Kg/sqcm) including shoes, bends, clamps etc. all complete jointing with seal ring conforming to IS : 5382 leaving 10 mm for thermal expansion (I) single socketed pipes |
| 30 | Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications. |
| 31 | FORM WORK: Providing, centering & shuttering using approved form work of plywood for footings, rafts, columns, walls, suspended floor slabs (horizontal or sloping), beams, side of slabs/ beams, Road works, chambers, PCC, and other misc. works at all levels & locations, inclusive of required scaffolding/ staging, props, prop-supporting structure, struts, material, labour, tools & plants, platforms, access, handrails, etc., and removal of formwork and staging, all complete as per drawings, specifications & as directed by Engineer-in-charge.Notes: 1. All scaffolding/ staging used shall be made of steel pipes as per approved design & drawings.2. The height will be considered from floor top supporting the staging to bottom of the slab/ beams/structure as applicable.3. In case of variable height of staging due to uneven ground or inclined slab/ beam, average height shall be considered over finished work area. |
| 32 | For PCC in buildings, road & drainage works, Column/ wall starters, and all types of foundation including footings, rafts, etc. |
| 33 | For staging height up to 3.5 m for Columns,pier, walls, suspended floor slabs (horizontal or sloping), beams, side of slabs/ beams, staircase, pedestals & tie beams and other in-situ components, etc. |
| 34 | Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5m, for every additional height of 1 metre or part thereof (Plan area to be measured). |
| 35 | Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 01, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysDec 02, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 11 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender