Tender For Rep/Replacement Of Flooring, Plinth Protection, Floor/Wall Tiling, Joinery And Plumbing/Sanitary Fittings And Certain Periodical Works At Main Camp And Tech Area And Rep To Compound Wall, Fencing, Jaffry Wall, Perimeter Wall, Plinth Protec
Tender Value
40 Lakhs
Estimated cost
Bid Submission
01 Dec 2026
19 days left
EMD
80000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chengalpattu → Tamil Nadu
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Rep/Replacement Of Flooring, Plinth Protection, Floor/Wall Tiling, Joinery And Plumbing/Sanitary Fittings And Certain Periodical Works At Main Camp And Tech Area And Rep To Compound Wall, Fencing, Jaffry Wall, Perimeter Wall, Plinth Protection, Parking, Hard Standing Etc At Golden Jubilee, Officer Mess/In-Living Area And Omq Area At Af Stn Tambaram. (8966/E8)
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc complete all as specified and directed by Engineer-in-Charge. |
| 2 | M&L for Pre-cast cement concrete block masonry with solid blocks type C1 1:3:6 (20 mm graded aggregate) exc. 10 cm in width and setting in cement mortar 1:6, complete all as specified and directed by Engineer-in-Charge. |
| 3 | M&L for 10mm thick in CM 1:6 rendering on brick or concrete surfaces finished even and smooth (without using extra cement), complete all as specified and directed by Engineer-in-Charge. |
| 4 | M & L for rendering 15mm thick in cement mortor 1:4 on brick wall / concrete surfaces, finished even and smooth without using extra cement with @ at 3% IWPC (IWPC measured separately) complete all as specified and directed by Engineer-in-Charge. |
| 5 | Supply only Liquid water proofing compound complete all as specified and directed by Engineer-in-Charge. |
| 6 | M&L Preparing newly plastered wall surfaces and apply two coats of oil boud distemper emulsion over a coat of primer, complete all as specified and directed by Engineer-in-Charge. |
| 7 | M & L preparation of new surfaces of walls plastered or unplastered etc and applying two coat of cement based paint paint on wall surfaces complete all as specified and directed by Engineer-in-Charge. |
| 8 | M & L for Preparation of old decorated surfaces (plastered/ unplastered) of ceiling by removing / scraping down all loose particle, smoke soot, moulds, moss & efflorescent salts, oil & greasy spots etc with using broom / steel patti / wire brush / sand papering or by any other mean including applying white cement based putty of any thickness where required for filling to depressions/nail holes/light cracks etc and to make the surface even and smooth after preparing the surface smooth applying one coat of white wash complete all as specified and directed by Engineer-in-Charge. |
| 9 | M & L for preparation of old decorated surfaces (plastered/unplastered) of walls/pillars /cornices by removing / scraping down all loose particle, smoke soot, moulds, moss & efflorescent salts, oil & greasy spots etc with using broom / steel patti / wire brush / sand papering or by any other mean, washing down with water including applying white cement based putty where required for filling to depressions/nail holes/light cracks etc and to make surface even and smooth after preparing the surface smooth applying one coat of cement base paint with highlighter of any approved shade @ 5 Sqm/kg/1 coat over & including a coat of exterior wall cement primer @10 Sqm/kg/1 coat (In case of second coat) as recommended for undercoat by manufacturer of cement base paint by using following brands of cement base paint and primer by brush or roller complete all as specified and directed by Engineer-in-Charge. |
| 10 | M & L for preparation of old decorated surfaces (plastered/unplastered) of walls/pillars /cornices by removing / scraping down all loose particle, smoke soot, moulds, moss & efflorescent salts, oil & greasy spots etc with using broom / steel patti / wire brush / sand papering or by any other mean, including applying white cement based putty where required for filling to depressions/nail holes/light cracks etc and to make the surface even and smooth after preparing the surface smooth applying one coat of oil bound distemper (washable) as approved tint/colour complete all as specified and directed by Engineer-in-Charge. |
| 11 | M&L preparation of old painted surface of wood and wood based materials of any description not otherwise described over 10 cm. width or girth shall include brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge. |
| 12 | M&L preparation of old painted surface of Steel and iron work of any description not otherwise described over 10 cm. width or girth shall include brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge. |
| 13 | Material and labour for preparation of old surfaces (plastered/unplastered) of walls/pillars /cornices by brooming down or steel wire brushing, scraping down smoke soot, moulds, moss & efflorescent salts, oil & greasy spots etc including applying white cement based putty where required for filling to depressions to make the surface even and smooth after preparing the surfaces applying one coat of weather proof exterior emulsion paint (wheather coat Apex, 100% exterior grade), as per existing or as approved tint/colour complete all as specified and directed by Engineer-in-Charge. |
| 14 | M&L 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including dismantling of existing stone slabs laid, bedded and pointed in any mortar complete all as specified and directed by Engineer-in-Charge. |
| 15 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed by Engineer-in-Charge. |
| 16 | M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor other side of waist slab with suitable arrangement complete all as specified and directed by Engineer-in-Charge. |
| 17 | S&F in repairs wash down water closet (pedestal pattern) complete white with plastic water closet seat black closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device and flush pipe of polythelene of low or density or PVC 32mm dia for low level flushing cistern complete all as specified and directed by Engineer-in-Charge. |
| 18 | S & F in repairs, plastic water closet seat & cover for pedestal pan , closed pattern with flat bottom & cover and mild steel chromium plated or aluminised hinging device,complete all as specified and directed by Engineer-in-Charge. |
| 19 | S & F in repair PVC valveless syphonic action type low level flushing cistern 10 Ltr capacity with inlet, ball valve, float and handle incl brackets and flush pipe of polyethylene of low or high density or PVC. 32 mm dia complete all as specified and directed by Engineer-in-Charge. |
| 20 | S & F in repairs health faucet with spray jet (hand shower) chromium plated incl all fitting & fixtures complete all as specified and directed by Engineer-in-Charge. |
| 21 | S&F in repair two way bib cock/tap 15 mm chromium plated complete fancy type of branded complete all as specified and directed by Engineer-in-Charge. |
| 22 | S&F in repair vitreous china wash basin, white, flat back size 550 x 400mm , 01 No. chramium plated piller tap, 01 Nos 32mm waste coupling and pipe, one pair of MS bracket, cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed by Engineer-in-Charge. |
| 23 | S&F in repairs PVC connections 15mm dia 600mm long (for cold/hot water connection with brass or PTMT flynuts and washer at both ends complete all as specified and directed by Engineer-in-Charge. |
| 24 | S & F in repair 125mm size brass chromium plated shower rose with or without swivel joints including fixing to steel pipe or union fixed complete all as specified and directed by Engineer-in-Charge. |
| 25 | S&F in repair 600mmx450mm belvelled edge looking mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood with pvc / alluminium frame and fixed to wooden plugs with chromum plated brass screws cup washers, complete all as specified and directed by Engineer-in-Charge. |
| 26 | S&F in repairs flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low / high level flushing cistern complete all as specified and directed by Engineer-in-Charge. |
| 27 | S & F in repairs 3 in 1 brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed of 15mm bore complete all as specified and directed by Engineer-in-Charge. |
| 28 | S&F 1000 Ltr capacity rotaional moulded polyethylene water storage tanks cylindrical vertical with closed top hoisted and fixed in position all as specified including dismantling & removing to store complete all as specified and directed by Engineer-in-Charge. |
| 29 | S&F 2000 Ltr capacity rotaional moulded polyethylene water storage tanks cylindrical vertical with closed top hoisted and fixed in position all as specified including dismantling & removing to store complete all as specified and directed by Engineer-in-Charge. |
| 30 | S&F in repair Cover/ lid for PVC water tank of any capacity complete all as specified and directed by Engineer-in-Charge. |
| 31 | Taking down of steel tubing and connections complete on walls floors etc for 15mm bore of pipe complete all as specified and directed by Engineer-in-Charge. |
| 32 | All as per item No. 31 above but bore of pipe in 20mm dia complete all as specified and directed by Engineer-in-Charge. |
| 33 | All as per item No. 31 above but bore of pipe in 25mm dia complete all as specified and directed by Engineer-in-Charge. |
| 34 | S&F Galvanised iron medium graded tubes with all fittings and fixed complete on walls / ceiling or laid in floors etc,15mm in dia complete all as specified and directed by Engineer-in-Charge. |
| 35 | All as per item No. 34 above but bore of pipe 20 mm complete all as specified and directed by Engineer-in-Charge. |
| 36 | All as per item No. 34 above but bore of pipe 25 mm complete all as specified and directed by Engineer-in-Charge. |
| 37 | Supplying and laying of 16mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in walls/trenches/ceilings complete all as specified and directed by Engineer-in-Charge. |
| 38 | Supplying and laying of 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in walls/trenches/ceilings complete all as specified and directed by Engineer-in-Charge. |
| 39 | Supplying and laying of 25mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in walls/trenches/ceilings complete all as specified and directed by Engineer-in-Charge. |
| 40 | S & F in repair 15mm bore bib taps, chromium plated cast copper alloy but fancy type, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-Charge. |
| 41 | S&F in repair 15mm bore cast copper alloy chromium plated angle cock / stop cock with long shank & cup concealed type complete all as specified and directed by Engineer-in-Charge. |
| 42 | S&F in repairs 15 mm dia fancy type stop valves/ angle cock chromium plated screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engineer-in-Charge. |
| 43 | S & F in repair 15mm bore dia. pillar taps (fancy type), cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge. |
| 44 | S&F in repairs 15mm bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed.(Minimum weight 15mm-90gms) complete all as specified and directed by Engineer-in-Charge. |
| 45 | S&F in repairs Ball valves 25mm bore high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe & fixed. (min. weight 25mm-455gms) complete all as specified and directed by Engineer-in-Charge. |
| 46 | S&F in repairs brass, chromium plated soap dish fixed to walls with chromium plated brass screws complete all as specified and directed by Engineer-in-Charge. |
| 47 | S&F in repair brass chromium plated tubular towel rails 20mm dia D type 60cm long between flanges complete all as specified and directed by Engineer-in-Charge. |
| 48 | Cleaning of tank by removing of all scale and dirts & etc, from tank and mouth of circutary pipe etc capacity exc.500 Ltr but not exc 1000 Ltr including writing of date of cleaning on each tank complete all as specified and directed by Engineer-in-Charge. |
| 49 | Cleaning of tank by removing of all scale and dirts & etc, from tank and mouth of circutary pipe etc capacity exc.1000 Ltr but not exc 2000 Ltr including writing of date of cleaning on each tank complete all as specified and directed by Engineer-in-Charge. |
| 50 | S & F PVC( SWR ) pipes 110mm dia single socketed , in any lenth with rubber ring joints as rainwater, soil waste and vent pipe (with all fittings) fixed to wall or laid in trenches incl taking down complete all as specified and directed by Engineer-in-Charge. |
| 51 | S & F PVC( SWR ) pipes 75mm dia single socketed , in any lenth with rubber ring joints as rainwater, soil waste and vent pipe (with all fittings) fixed to wall or laid in trenches incl taking down complete all as specified and directed by Engineer-in-Charge. |
| 52 | S&F PVC (SWR) bends any radius 110mm bore in repairs complete all as specified and directed by Engineer-in-Charge. |
| 53 | S&F PVC (SWR) bends any radius 75mm bore in repairs complete all as specified and directed by Engineer-in-Charge. |
| 54 | S&F in repairs PVC grating square or circular fitting of size 100 mm with hole etc complete all as specified and directed by Engineer-in-Charge. |
| 55 | Taking down shutters of any description exc 1 Sqm but n.exc 2 Sqm each and removal from site complete all as specified and directed by Engineer-in-Charge. |
| 56 | Resecuring and easing & adjusting without taking down shutters of any description exc 1 Sqm and n exc 2 Sqm each including all fittings complete all as specified and directed by Engineer-in-Charge. |
| 57 | S & F 30 mm thick 2nd class hard wood factory made glazed and skeleton shutter divided into square, with plain chamfered or rounded metred and rebital sash bar any number and framing moulded windows, ventilators, etc. provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.20 (b) fitted to chowkats complete all as specified and directed by Engineer-in-Charge. |
| 58 | S & F factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, thickness 35 mm, etc complete all as specified and directed by Engineer-in-Charge. |
| 59 | S & F 100mm mild steel butt hinges medium weight cold rolled complete all as specified and directed by Engineer-in-Charge. |
| 60 | S & F 125 mm aluminium anodised barrel tower bolts of extruded section complete all as specified and directed by Engineer-in-Charge. |
| 61 | S & F 125 mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engineer-in-Charge. |
| 62 | S & F 300mm long aluminium alloy, anodised,sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed by Engineer-in-Charge. |
| 63 | S & F mild steel 175 mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer-in-Charge.( short type, fighter jet aeroplane shape type) |
| 64 | S&F 140 mm size floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and directed by Engineer-in-Charge. |
| 65 | S & F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of apreture 1.00 mm & fixed with stainless steel wire, staples complete all as specified and directed by Engineer-in-Charge. |
| 66 | M & L preparation of surfaces of wood based material any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge. |
| 67 | Taking down chowkats or frames with shutters (without taking off shutter from the frames) n exc. 1.5 sqm each complete all as specified and directed by Engineer-in-Charge. |
| 68 | S&F Solid PVC Door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification & drawing complete all as specified and directed by Engineer-in-Charge. |
| 69 | S&F Factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tube for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the style & rails with suitable PVC sheet beading, and jointed together with solvent cement,supplying & fixing in the frame at site complete all as specified and directed by Engineer-in-Charge. |
| 70 | S & F 100 MM Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed by Engineer-in-Charge. |
| 71 | S&F in repairs door closer, aluminium (extruded section body) hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and weight between 61 to 80kG complete all as specified and directed by Engineer-in-Charge. |
| 72 | S&F in repair pre-laminated 18 mm thick lead free factory made 100% Solid WPC (Wood Polymer composite) sheet having high natural fiber contains 25 to 30 % wood colour sheet with density not less than 600 kg /Cbm bent 90°and the weight of sheet of 1 sqm should be 11 kg(+/- 5%) manu facture by ISO-9001-2015 certified company, the sheet should be 100% termite/water proof, fire rertradent, Eco friendly, and finish at all edges at level for making edges lipping using binding tape etc as in Kitchen cupboard,Cabinet fitted with SS screws etc complete all as specified and directed by Engineer-in-Charge. |
| 73 | S & F continous (piano) hinges mild steel, 40mm width of flaps (when open) , bright finish or electrogalvanised in repair complete all as specified and directed by Engineer-in-Charge. |
| 74 | S&F in repair Magnetic catcher as appproved by GE fitted with nuts and bolts complete all as specified and directed by Engineer-in-Charge. |
| 75 | M&L for Zinc finished telescopic drawer channel 18 inch long, ball bearing slide for kitchen cabinets and wardrobe complete all as specified and directed by Engineer-in-Charge. |
| 76 | M& L for Auto closing hinges 35 mm of 0 crank (KH-001 or 8 crank (KH-002) openble at 110 degree for kitchen cabinet shutters complete all as specified and directed by Engineer-in-Charge. |
| 77 | S&F in repair mortice lock of mild steel vertical type of size 150mm 6 Lever complete all as specified and directed by Engineer-in-Charge. |
| 78 | S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and directed by Engineer-in-Charge. |
| 79 | S & F for brass handles, cast type, polished bright complete all as specified and directed by Engineer-in-Charge. |
| 80 | Hacking out old broken glass from metal frame of any thickness incl punching or drilling out old glazing pin/springs clips and providing and fixing new ones, complete all as specified and directed by Engineer-in-Charge. |
| 81 | S&F sheet glass 4mm thick ordinary quality & glazing with oil putty in square n.exc 0.5 Sqm in each pane at any height and any story complete all as specified and directed by Engineer-in-Charge. |
| 82 | S&F sheet glass 4mm thick frosted quality & glazing with oil putty in square exc 0.5 Sqm in each pane at any height and any story complete all as specified and directed by Engineer-in-Charge. |
| 83 | S&F in repair for stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with galvanised wire staples complete all as specified and directed by Engineer-in-Charge. |
| 84 | Demolition floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed by Engineer-in-Charge. |
| 85 | Demolition of cement concrete (Un-reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-Charge. |
| 86 | M&L for 75mm thick Plain cement concrete (1:4:8) type D2 (40mm graded stone aggregate) as in sub base, rough finished surface complete all as specified and directed by Engineer-in-Charge. |
| 87 | M&L for 40 mm thick plain cement concrete (1:2:4) type B1 (20mm graded stone aggregate) finished the surface even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. |
| 88 | M&L for Plain cement concrete C-2 type 1:3:6 (40mm graded aggregate) 75mm thick as in plinth protection complete all as specified and directed by Engineer-in-Charge. |
| 89 | M&L for 25mm thick cement concrete (1:2:4) type B0 (12.5mm graded stone aggregate) as in sub-base and finished surface even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. |
| 90 | M&L for non skid coloured ceramic tiles 7 to 8mm thick (square or rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc., laid over and including cement screed bed or bedding layer in CM (1:6), 15mm thick and tiles jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, complete all as specified and directed by Engineer-in-Charge. |
| 91 | M & L glazed ceramic coloured tiles of size 300x450x7 mm / 350x 250x 7mm/ 450X 350X 7mm thick on vertical surface as in dados, skirting etc, set and jointed in neat cement slurry over and including 10mm thick plaster in cement mortar 1:4, pointed with white/ coloured cement to match complete all as specified and directed by Engineer-in-Charge. |
| 92 | M&L Vitrified Ceramic tiles, light shade, 10mm thick (Square or rectangular) polished, area of each tile not exc 0.36 Sqm in floors etc., and laid over and including cement screed bed or bedding layout in CM (1:6), 15mm thick and jointed in neat slurry and pointed in white or coloured cement to match using light shade coloured tiles complete all as specified and directed by Engineer-in-Charge. |
| 93 | M&L Vitrified Ceramic tiles 10mm thick (Square or rectangular) polished, area of each tile not exc 0.36 Sqm in skirting / dados etc and including 10mm thick rendering in CM(1:4) baking coat and jointed in neat slurry and pointed in white or coloured cement to match using light shade coloured tiles complete all as specified and directed by Engineer-in-Charge. |
| 94 | Taking down Aluminium chowkats/Frames of area n.exc 1.5 Sqm with shutter (without taking off shutters from the frame) each complete all as specified and directed by Engineer-in-Charge. |
| 95 | All as per item No 94 above but area exc 1.5 Sqm & n.exc 4 Sqm complete all as specified and directed by Engineer-in-Charge. |
| 96 | S & F powder coated (minimum thickness of powder coating 50 micron) aluminium anodised frame for doors, windows, ventilators and partition with one or more rebates including joining cleat for fixing, etc complete all as specified and directed by Engineer-in-Charge. |
| 97 | S & F powder coated (minimum thickness of powder coating 50 micron) aluminium anodised door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws, etc complete all as specified and directed by Engineer-in-Charge. |
| 98 | S & F for powder coated (minimum thickness of powder coating 50 micron) aluminium anodised window and ventilator shutters, fixed /sliding/side hung type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws,three track etc complete all as specified and directed by Engineer-in-Charge. |
| 99 | S&F aluminium powder coated grills (pattern DG-104) weight of 2.00 to 3.20 Kg/Sqm for windows, ventilators, etc including jointing, cleats etc and fixed with medium screws into walls / frame work etc complete all as specified and directed by Engineer-in-Charge. |
| 100 | S&F 5.5 mm thick sheet glass, ordinary quality, and sheet glass is ground or obscured or frosted on one side fixed in aluminium door/window/ ventilator/ partition glazing with rubber beading complete all as specified and directed by Engineer-in-Charge. |
| 101 | M & L for 12mm thick Prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination , fixed with screws to timber frame work/alluminum work like partition or door etc complete all as specified and directed by Engineer-in-Charge. |
| 102 | Dismantling wall and ceiling boards (fibre, pulb, insulation etc) or insulation boards slabs/blankets any thickness including cover fillets complete all as specified and directed by Engineer-in-Charge. |
| 103 | S & F for semi perfortaed 12mm thick micro tegular edges GRG false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 4 76 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main- T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of s1ze 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1 OOOmm length and Lshape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and complete all as specified and directed by Engineer-in-Charge. |
| 104 | Dismantling wrought iron or mild steel work of any description not other wise provided for complete all as specified and directed by Engineer-in-Charge. |
| 105 | M&L for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to including joining welding and connecting each other to form a cage for water tanksFe.290.Gde-E-165 complete all as specified and directed by Engineer-in-Charge. |
| 106 | S & F for hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed by Engineer-in-Charge. |
| 107 | M&L for preparation of new or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge. |
| 108 | S&F for Solid PVC Wall Lining consisting of 5mm thick Plain colour / wood grain printed PVC sheet inclusive of solvent cement and fixing at site on 18mm minimum thick PVC/WPC frame as per specifications and drawing including dismantling existing boards of any description any pattern including fillets, frame etc complete all as specified and directed by Engineer-in-Charge. |
| 109 | M&L for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame complete all as specified and directed by Engineer-in-Charge. |
| 110 | M&L for square rubble masonry, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge. |
| 111 | M & L for PCC type D2 1:4:8 (using 40mm graded stone aggregate) in foundations, filling and mass Concrete complete all as specified and directed by Engineer-in-Charge. |
| 112 | M&L for flush pointing with CM 1:4 to random rubble masonry, uncoursed or brought upto course complete all as specified and directed by Engineer-in-Charge. |
| 113 | M&L brick work with fly ash modular bricks built in CM 1:6 straight or curved on plan exc 6 mtr mean radius complete all as specified and as directed by Engineer-in-Charge. |
| 114 | M&L PCC 1:2:4, type B1 (using 20 mm graded stone aggregated) as in coping, cills, steps, bands, bed plate, benching to manholes and drains etc including necessary form work complete all as specified and directed by Engineer-in-Charge. |
| 115 | Taking down cement plaster any description on brick or stone walls, roof plater etc including raking out joints,hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge. |
| 116 | M&L for Preparing of newly plastered surfaces and applying three coats of white wash on walls complete all as specified and directed by Engineer-in-Charge. |
| 117 | Dismantling RCC fencing posts or struts of any section embedded in concrete/brick masonry including taking out embedded portion and making good disturbed ground complete all as specified and directed by Engineer-in-Charge. |
| 118 | Dismantling fencing wire mesh of any type & description complete all as specified and directed by Engineer-in-Charge. |
| 119 | Supply only MS galvanised chain link fencing haevy zinc coated (Hot dip), aparture size 50mm and wire of 3 to 4 mm dia complete all as specified and directed by Engineer-in-Charge. |
| 120 | Fixing only chain link fencing any mesh size and type to any type of standard, rails, iron angle posts, straining bolts etc incl provision of binding wire complete all as specified and directed by Engineer-in-Charge. |
| 121 | S & F in repairs galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins etc complete all as specified and directed by Engineer-in-Charge. |
| 122 | Restraining, resecuring including making good galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacings andstraining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc, complete all as specified and directed by Engineer-in-Charge.Note : Each line of wire shall be measured and paid separately. |
| 123 | S&F in repairs of concertina coil fencing made from high tensile spring steel, high Carbon wire conforming to IS-4454 duly hot Dipped Galvanished as per IS -4826 with 230GSM, 600mm dia, 10 Metre openable length, with galvanished coating and punched tape material as per IS-513, having 30-35 Nos rounds per 6 mtr length (before streaching) having medium barbs fixed to the existing mild steel post over the boundray wall upto height 3m complete all as specified and directed by Engineer-in-Charge.Note: Horizontal barbed wire & angle iron support shall be measured and paid sepately under relevent items of Schedule \\"A\\". Measurement shall be made for stretched length. |
| 124 | M&L mild steel framed work as hung gates, including pintle hinges, stops, hand-made sliding bolts, etc. as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks, and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed by Engineer-in-Charge. |
| 125 | S & F mild steel screw bolts of 11 to 15mm diameter of neck (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm and not exc 10cm complete all as specified and directed by Engineer-in-Charge. |
| 126 | M&L for MS round bars, 10mm dia & over, cut ot length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with wire complete all as specified and directed by Engineer-in-Charge. |
| 127 | Excavating in post holes (or similar holes) each n exc 0.5cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in hard/dense soil complete all as specified and directed by Engineer-in-Charge. |
| 128 | M & L for PCC (1:3:6) type C-2 (using 40mm graded stone aggregate) as in foundation filling & mass concrete for post/pillars etc incl formwork complete all as specified and directed by Engineer-in-Charge. |
| 129 | S & F in repairs for 4mm thick polycarbonate sheet of approved make with UV protection on both sides, fixed to the existing / new MS gate frame with beading, SS screw, nuts, bolts and washers with neoprene rubbers gaskets, including cutting to size, drilling over size holes and all necessary fittings complete all as specified and directed by Engineer-in-Charge. |
| 130 | M&L for welding in repairs exc 6mm and n.exc 9mm in thickness and n.exc 2.5cm in length complete fixed in position complete all as specified and directed by Engineer-in-Charge. |
| 131 | M&L for welding in repairs exc 6mm and n.exc 9mm in thickness exc 2.5cm n.exc 5cm in length complete fixed in position complete all as specified and directed by Engineer-in-Charge. |
| 132 | Repair to existing MS gate of any size by dismantling damaged portions, straightening and realigning frame/shutters, replacing defective MS members, hinges, holdfasts, locking arrangements, tower bolts, handles and other fittings as required including welding, grinding, adjusting and greasing for smooth operation etc complete all as specified and directed by Engineer-in-Charge.Note:-MS material used for repair work will be measured and paid separately. |
| 133 | M & L for providing precast cement concrete louvres and jallies, 40mm thick Type B0 1:2:4 using 12.5mm size aggregate including all mouldings but excluding frame set with CM 1:4 and demolition complete all as specified and directed by Engineer-in-Charge. |
| 134 | Dismantiling of AC sheets / Galvolume sheet / GI sheet Corrugated or Semi corrugated etc in roof coverings/wall caldding complete all as specified and directed by Engineer-in-Charge. |
| 135 | S & F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge.Note: Rate quoted deemed to include cost of making good disturbed masonry surface to match with existing etc using PCC 1:2:4/brick work/cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge. |
| 136 | S & F for pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof overing/ cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in-Charge. |
| 137 | M &L 6 mm thick Asbestos Cement sheet corrugated or semi corrugated in roofs, walls etc and fixed with J or L hook or cranked bolts with washers etc complete all as specified and directed by Engineer-in-Charge. |
| 138 | S&F for Steel work in tubular posts, trusses, purlin, rafter etc. including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS-1161-1979 Fe-410W Grade E-250 Quality A complete all as specified and directed by Engineer-in-Charge. |
| 139 | S&F MS Plain plates, square cut, with riveted, bolted or welded attachment Fe-410-W (Gde-E-250) quality A complete all as specified and directed by Engineer-in-Charge. |
| 140 | Demolition of cement concrete (Un-reinforced) in ground floors and pavings n exc. 15cm thick complete all as specified and directed by Engineer-in-Charge.(Below or above ground level). |
| 141 | M&L for 40 mm thick plain cement concrete (1:2:4) type B1 (20mm graded stone aggregate) finished the surface even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. |
| 142 | Demolition of stone slabs / chequered tiles / Interlocking tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar and rubbish off the premises complete all as specified and directed by Engineer-in-Charge. |
| 143 | M&L sand filling under paver blocks including watering and consolidation complete all as specified and directed by Engineer-in-Charge. |
| 144 | M & L for 60mm thick machine pressed precast cement concrete interlocking paver blocks M-35 garde any shape and size with grey cement and pigment rubber moulded with vibration technology set and jointed as per manufactures instructions laying over sand cushioning complete all as specified and directed by Engineer-in-Charge. Note : (i) Rate quoted by contractor shall deemed to inclusive of filleting the side of pavement with PCC (1:2:4) type B1 upto 150mm.(ii) Sand cushion will be measured & paid separetely. |
| 145 | M&L for chequered cement concrete tiles 300x300x25 mm thick with grey cement and pigment, machine pressed, set jointed and pointed in neat cement slurry in floors including 15 mm thick screed bed layer in CM 1:6 complete all as specified and directed by Engineer-in-Charge. |
| 146 | Demolition of Concrete (Reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed by Engineer-in-Charge. |
| 147 | M&L for Pre Cast Cement Concrete 1:2:4 type B1 (using 20 mm graded aggregate) as in Cover slab for manholes etc set in cement mortor 1:6 including use and waste necessary form work (Reinforced shall be measured and paid seprately) complete all as specified and directed by Engineer-in-Charge. |
| 148 | M&L for Mild Steel TMT bars, 10mm dia & over , cut ot length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with wire complete all as specified and directed by Engineer-in-Charge. |
| 149 | M&L for MS TMT bars, 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders , cut ot length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with wire complete all as specified and directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 01, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysDec 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 21 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender