Tender For Repair To Plumbing, Joinery, Flooring And Tiling With Sanitary Fittings And Parking Sheds Other B/R Nature Works In The Area Of Age B/R-Ii Under Ge (East) Delhi Cantt-10
Tender Value
48 Lakhs
Estimated cost
Bid Submission
01 Dec 2026
19 days left
EMD
96000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
New Delhi → Delhi
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair To Plumbing, Joinery, Flooring And Tiling With Sanitary Fittings And Parking Sheds Other B/R Nature Works In The Area Of Age B/R-Ii Under Ge (East) Delhi Cantt-10
BOQ
| Sl. No. | Item Description |
| 1 | Taking down chowkat or frames with shutters (without taking out shutters from frame) exc. 1.5 sqm but not exc 4 sqm each complete all as specified and as directed. |
| 2 | Taking down chowkat or frames not exc. 1.5 sqm each with shutters (without taking off shutters from frames) complete all as specified and as directed. |
| 3 | Taking down shutters of any description exc.1.00 sqm and n. exc 2.00 sqm each complete all as specified. |
| 4 | S&F Plain, solid, straight chowkhats and frames of 2nd class hard wood, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints, supplied and fixed. |
| 5 | S&F Mild Steel framed work as in door or gates of angle or other section with gusset plates, rail, braces, etc and similar work incl primer conforming to Fe 410-0 or Fe 310-0 complete. |
| 6 | S&F Pressed steel frames size 105x60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, including filling hollow of frame with PCC 1:3:6 etc. complete all as specified and directed. |
| 7 | Descritpion all as per item No. 6.00 above but size 125x60mm, complete all as specified and as directed. |
| 8 | S&F 35mm thick 2nd class hard wood glazed and sekeleton shutter's open rebated prepare to receive glass gouge etc edges of framing plain chamfered or ronded fitted with cut and mitered bead's for securing glass gauge etc size of marker of shutters as per SSR Part-I sec-8 clause 8.2(a). |
| 9 | S&F 30mm thick flush shutter, solid core construction, with block board core and plywood face panel commercial type on both sides. |
| 10 | S&F 30mm thick pre laminated flush shutter, solid core construction, with block board core and designed face Pre- lamination finish on both sides as approved by Engr in charge. |
| 11 | S&F 2nd class Hard Wood 30mm thick Plain, framed, paneled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers including applying two coats of synthetic enamel paint over one coat of pink primer complete as specified and as directed. |
| 12 | S&F Solid PVC door frame of size 50mm x 95mm made out of wood grain printed PVC sheet used reinforced with M.S. tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed. |
| 13 | S&F factory Made Solid PVC Door/ PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded prelam coloured PVC Sheet on both face, supplying & fixing in frame at site as per secification & directed |
| 14 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65x100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.Note: (a) M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately.(b) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 15 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid moulded decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. Note: stainless steel butt hinges and necessary S.S screws shall be paid separately. |
| 16 | S&F or in repair 100mm long butt Hinges, medium weight, cold rolled mild steel fixed complete. |
| 17 | S&F or in repair stainless steel heavy dutty butt hinges 100mm long complete all as specified directed by Engr-in-Charge |
| 18 | S&F or in repair 300mm long aluminum alloy anodized sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast sec and fixing bolts and sliding bolts of extruded sec or cast aluminum alloy and fixed all as spd and directed. |
| 19 | S&F or in repair 150mm long aluminum anodized barrel tower bolt of cast aluminiun alloy section and fixed all as spd and directed. |
| 20 | S&F or in repair Aluminium handles, 150mm size cast type anodised complete all as specified and directed |
| 21 | S&F or in repairs for mild steel 300 mm long, ordinary rat tail rod pattern springs including roller and roller plate complete |
| 22 | S&F or in repair 300mm MS Helical door spring including roller & roller plate complete all as specified and as directed by Engineer-in-Charge. |
| 23 | S&F or in repair Floor door stoper of aluminium alloy body with hard drawn steel spring 140mm long. |
| 24 | M&L Resecuring or Easing and adjusting, without taking down shutters of doors/windows for easy opening /closing, tightening of hinges and changing its position or adjustment of tower bolts/ sliding bolts etc area not exc 2 sqm each complete all as specified and directed. |
| 25 | M&L Resecuring or Easing and adjusting sliding doors, (with/without taking down shutters) for easy opening /closing by repair/replaceing tracks, sliding wheels, clits, doors etc and changing its position or adjustment of tower bolts/sliding bolts area not exc 4 sqm each complete all as specified and directed. |
| 26 | S&F Aluminium alloy powder coated (50 micron) anodized three track heavy duty aluminium (glazed/ gauged) door shutters sliding type with frame incl toughened glass of thickness 6-8 mm, obscured or frosted and stainless steel wire mesh, with or without sash bar aluminium section weighting 0.55 Kg per mtr including frame necessary joining cleats, glazing clips, rubber packing, anodised aluminium beading, sliding channel, roller screws incl 200 mm long tower bolt-2 Nos on each leaf, 200 mm long Aluminium handle -02 Nos on each leaf, 4 lever lock brass 100 mm long mortice lock, including all fittings & repair around frame with plaster, puttty, paint complete all as per direction of Engr-in-charge. Door shall have following features:(i) Sealing to protect from noise and dust (ii) shall withstand maximum wind speed of 8 m/s (iii) drainage solution to keep out heavy rains (iv) anti lift plug and anti burglary locks for extra security (v) custom-engineered rollers for smooth operation. |
| 27 | S&F Aluminium alloy powder coated (50 micron) anodized door frame of section 100mm x 44 mm x 2 mm thick, door shutter of aluminium section of size 85 mm x 44 mm x 2 mm thick, top rail and both styles of size 100 mm x 44 mm x 2 mm thick, lock rail and bottom rail of size 115 mm x 44 mm x 2mm thick incl aluminium anodized snap beading and rubber packing & 5.5 mm thick colour designer glass incl 200 mm long tower bolt-2 Nos, 200 mm long Alum handle -02 Nos on each leaf, 4 lever lock brass 100 mm long mortice lock (Make :- Godrej), & double action floor door spring(Sandhu/Samrat) heavy duty suitable for 1 m wide shutter for each leaf, complete all as specified and as directed. |
| 28 | S&F powder coated three track aluminium (glazed/ gauged) window shutters sliding type incl 5.5mm thick glass or stainless steel wiremesh, without sash bar aluminium saction weighting 0.55 Kg per mtr including frame necessary joining cleats, glazing clips, rubber packing, anodised aluminium beading , sliding channel,roller screws including fittings complete all as per direction of Engr-in-charge. |
| 29 | S&F powder coated aluminium window/ ventilator shutters incl 5.5mm thick glass or stainless steel wiremesh, side hung type without sash bars, aluminium sections weighing 0.55 Kg/m including frame and necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long (1 No.) hinges type B-21 100 mm long (2no), aluminium tower bolt 100 mm long (2no.), suitable handle (1 No.) complete all as specified. |
| 30 | S&F aluminium anodized grills with 6mm x 5mm aluminium section having square gap of 100mm with fixing arrangement complete all as specified and directed |
| 31 | M&L for Providing and fixing factory made uPVC white colour Sliding window Three track area not exceeding 2.00 sqm each made of extruded profiles with wall thickness of 2.3mm (+0.2 mm). Window profile with hollow section with multi chamber. Frame (108mm x 52mm), sliding sash (42mm x 85mm). Sliding mesh Sash (42mm x 67mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor includes cost of sheet glass 5.50mm thick selected quality ground or obscured or frosted, on one side and glazing with suitable rubber packing in required sizes including all accessories complete all as specified. Net opening will be measured for payment purpose. |
| 32 | M&L for Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm (+0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 104mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2+ 2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 5mm thick glazing with selected quality glass. (Note: The unit rate quoted by contractor includes cost of sheet glass 5.50mm thick selected quality ground or obscured or frosted, on one side and glazing with suitable rubber packing in required sizes including all accessories complete all as specified. Net opening will be measured for payment purpose. |
| 33 | S&F Box type Steel windows with double shutters (inside for wiremesh & out side for glass), hinges, steel handle, tower bolt and steel peg stay complete with glazing bars dovetailed or welded. WIRE MESH Stainless steel wire mesh of 0.3 mm nominal dia of wire and average width of aperature 1.40mm. Grills window shall be provided with grill made of 10mm square MS bars welded to 12mmx6mm thick MS plate. Distance between bars should not be more than 12cm c/c. Total grill unit shall be enamel painted and fixed to window frame with screw . Note: The glazed/Guaged shutter includingguard bars shall be measure once i.e. as per area of opening. No separate payment of separate shutter i.e. glazed and fly proof and guard bars shall be made. Area of shutter shall be the area of opening. The rate quoted by the contractor is deemed to inclusive two coat of paint over a coat of primer of all aspects incl all fitting,glass, wire mesh, guard bar, as specified in Drg No CEDZ/TD/289 sheet 1 R/2 and 2R/2. |
| 34 | Hacking out old brocken glass (any thickness, size, quality or description) from wooden/metal frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads |
| 35 | S&F 4mm thick sheet glass, selected quality and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified. |
| 36 | S&F 4mm thick Figured glass, pinhead type with oil putty in squares not exc 0.5 sqm each pan complete all as specified. |
| 37 | S&F or in repair stainless steel wire cloth, 0.36 mm nominal dia. of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or stainless steel wire staples complete all as specified and directed. Note- Welder with welding machine reqd to fix wiremesh in old steel windows |
| 38 | M&L two coats of synthetic enamel painting on new/ old steel surfaces of any description over 10 cm in width or girth not otherwise described including prepration of surfaces |
| 39 | M&L two coats of synthetic enamel painting on new wooden surfaces of any description over 10 cm in width or girth not otherwise described over a coat of pink primer. |
| 40 | Dismantling wall and ceiling boards ( fibre pulp, insulation etc ) or insulation boards/ slabs/ blank ets, any thickness, incl cover fillets all as directed. |
| 41 | S&F GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm center to center/ Intermediate channel 0.9 mm thick having to equal flanes of 15 mm each and web of 45 mm suspended from soffit at approx x 900mm center to center with GI cleat and steel expension fastners with and including ceiling section ( not exc 1.2m length ) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.50 mm fixed to the intermediate channel at 457 mm center to center. Including Hangers 6mm dia GI up to 1200 mm length) adjusting level fixed to roof slab by means of ceiling cleats made out of GI Flat 40x3mm size 60mm long and expansion hold fastners 12.50 dia. 40 mm long complete all as specified and as directed. |
| 42 | S&F Providing and fixing 10 mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class hard wood fillets, or metal frame and work with GI wire mesh( fillet, Metal frame work and GI Wire mesh paid seprately) including sunk or raised mouloding complete all as specified and as directed. |
| 43 | M&L for aluminium anodised snap grid frame work of size 605x605mm for false ceiling with hanging arrangement of 6mm dia G .I ( u p to 1200 mm length ) adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40x3 mm size and 60mm long and expension hold fastners 12.50mm dia 40mm long complete all as specified and directed. |
| 44 | M&L for Non asbestos 4mm thick fibre cement building boards fixed or laid / inserted to aluminium frame work with screws as in false ceiling fixed in ceiling flat or sloping complete all as specified and directed. |
| 45 | S&F in repairs of Modular wardrobe,cupboards, cabinets, drawers, shelfs, vanity, dressing table including shutters (depth of 45 Cm up to 70 Cm) etc, all front side, bottom, top, two sides and partions etc made out of 15-18 mm thick HDHMR board and back side made out of 8-10 mm thick HDHMR board (Action tesa or equivalent) with machine pressed 0.5 to 0.8 mm thick fabric/glossy colour laminate on all exposed front side and other sides decorative laminations. All exposed edges of boards with machine pressed edge band 0.8mm from rehau Germanetc (colour of laminates, design & paterns of partations/ etc as approved by GE) including all accessories of fittings - Auto/soft closing hinges for shutters, C/J gola profile for handel less or SS handel, telescopic channels 18'' / 20'' long, rollers for smooths sliding of drawers magnetic catch, etc as required complete all as specified and directed by Engr-in-charge. (Note: Only front face shall be measured and paid irrespective of area of HDHMR boards provided and fitting as required shall be deemed to be included in unit rate quoted) |
| 46 | S&F in repairs Drapery rod 25mm dia aluminium, powder coated teak wood texture finish 1 mm thick, with end bulbs & brackets complete all as specified and directed. |
| 47 | S&F in repair stainless steel curtain rod/ rail fancy type 25 mm dia including ss bracket and ss fancy type lattoo, etc complete all as specified and directed. |
| 48 | M&L for repair to existing steel rolling shutters/ gates by repairing/welding/ oiling/ greasing to anchoring rod,springs,side guide channel etc incl dismantling existing steel rolling shutters of any width and refixing after making serviceable after adjusting springs including two coats of paint complete all as spd and directed. |
| 49 | M&L for repair to existing steel window/door by welding/replacing hinges/handle or removing the steel window shutters from the frame and re-fixing after making serviceable all as specified |
| 50 | S&F 1.00 mm thick plain black steel sheet in hearths; covering to door shutters; covering to doorchowkats (frames); chullah hoods; water tanks; water troughs;ducts; urinal troughs and funnels, etc. cut to size edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required incl priming complete all as specified and directed. |
| 51 | S&F in repair 150mm size double action spring, hinge, mild steel with steel wire spring, stove enamelled black, fixed in repair complete all as specified and directed. |
| 52 | S&F in repair Aluminium (die cast) body door closer hydraulically regulated designation No 2 universal type suitable for door shutter of 701 to 851mm in width and of weight between 36 to 60 kg, fixed in repairs, complete all as specified and as directed. |
| 53 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the permises complete all as specified and directed. |
| 54 | M&L for Vitrified Ceramic light shed Coloured tiles 8 to 10 mm thick (square/rectangular) polished, area of each tiles n exceeding 0.36 sqm in floors/skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tiles including 15 mm thick screed bed in CM 1:6, complete all as specified and as directed. |
| 55 | Description all as item No. 54.00 above but on vertical surfaces such as skirting / dados with and including 10 mm thick CM 1:4 as in backing coat complete all as specified. |
| 56 | M&L for coloured non skid ceremic tiles 7 to 8mm thick (Square/reactangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jounted in neat cement slurry and pointed in white or coloured cement to match including 15 mm thick screed bed in CM 1:6, complete all as specified and directed. |
| 57 | M&L for glazed coloured ceremic tiles sizes 600x300x7 or 450x300x 7mm thk tiles on vertical surfaces , such as skirting/dado ,incl 10 mm rendering in cement mortar 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles complete all as specified and directed. |
| 58 | S&F in repair stainless steel kitchen plate rack size 900 x 750 x 250 mm deep made out of 1mm thick sheet including fitting arrangement complete. Make- Maharaja/Nirali/Prayag |
| 59 | Taking down cement or lime plaster any description on brick or stone walls,ceilings etc including recking out joints hacking for key scrubbing down with waters and removal of rubbish from the premises as directed. |
| 60 | M&L Rendering 15mm thick in cement mortar 1:4 on fare faces of brick work or concrete surfaces and finished the surface even and fair without using extra cement complete all as specified. |
| 61 | M&L for preparation of new/ old plastered surface of walls and applying two coat of cement base paint over 2mm thick coat of wall care putty and a coat of Primmer, Priming plastered and other surfaces with alkaliresistant priming paint on walls complete all as specified and directed. |
| 62 | M&L Rendering 15mm thick in cement mortar 1:6 on other than fair faces of brick work or concrete surfaces and finished the surface even and fair without using extra cement complete all as specified. |
| 63 | M&L for preparation of new/old plastered surface of of walls and applying two coat of Oil bound distemper a coat of primmer with Chalk whiting, on plastered surfaces, prepara-tory to distempering over 2mm thick wall care putty on walls complete all as specified and directed. |
| 64 | Rendering 5mm thick in cement mortar 1:3 on fare faces of brick work or concrete surfaces and finished the surface even and fair without using extra cement in ceiling complete all as specified. |
| 65 | M&L for preparation of new plastered surface of ceiling and applying three coats of white washing and preparity to plastered surface complete all as specified and directed. |
| 66 | Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and as directed. |
| 67 | S&F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour as approved having tensile strength of 550 MPA as in roof covering/cladding to wall, fixed with self tapping screws as specified and including cutting chasing of wall, complete all as specified and directed. |
| 68 | Dismantling wrought iron or mild steel work of any description complete all as specified |
| 69 | M&L Mild Steel framed work such as grills, grating,gate etc with ends of bars shouldered or riveted or forged into spikes framed guard bars and similar work confirming to Fe - 290-0 or E-165 including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed |
| 70 | S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 |
| 71 | S&F in repair SS Grating jalli/doom 100 mm dia with or without waste hole complete all as specified. |
| 72 | S&F in repair SS Grating jalli/doom 75 mm dia with or without waste hole complete all as specified. |
| 73 | S&F in repair of 110 mm bore SWR pipes single socketed in any length with rubber ring joints fixed to walls, floors, trenches etc complete all specified and directed. |
| 74 | S&F 110 mm bore PVC (SWR) bends with rubber ring joints fixed to walls complete all as specified and directed. |
| 75 | S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor or in wall complete all as specifed and directed. |
| 76 | S&F 75 mm dia PVC Bends with access dooe complete all as specified and directed |
| 77 | Taking up or down steel tubing 15 mm bore and connection including cleaning for refixing. complete all as specified and as directed by Engineer-in-Charge |
| 78 | Description all as per item No. 77.00 above but for 20mm Dia. |
| 79 | S&F steel tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors, bore of pipe 15 mm dia.including making hole in RCC slabs for vertical pipes & making good the same with Cement Concrete I:2:4 complete all as specified and as directed by Engineer-in-Charge |
| 80 | Description all as per item No. 79.00 above but for 20mm Dia. |
| 81 | S&F in repair looking mirror size 600x450mm mounted on 6mm thick PVC sheet and aluminium frame all around incl fix with necessary fixing arrangement complete. |
| 82 | S&F in repair CP towel rail 600mm long complete all as specified and as directed by Engineer-in-Charge complete all as specified and directed. |
| 83 | S&F in repair 600 mm long PVC connection with stainless steel armed 15 mm bore with nuts complete all as specified and as directed by Engineer-in-Charge complete all as specified and directed. |
| 84 | S&F in repair for 15 mm dia fancy type CP bib taps half turn with wall flange with screwed down, screwed for iron pipe or for brass ferrule including cap and fixed complete all as specified and as directed by Engineer-in-Charge |
| 85 | S&F in repair for 15 mm dia fancy type CP Stop valves, Cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by Engineer-in-Charge . |
| 86 | S&F in repair 15 mm bore fancy type angle valves half turn chromium plated fancy type with wall flange screwed down high pressure screwed both ends for iron pipes or for unions complete all as specified and as directed by Engineer-in-Charge. |
| 87 | S&F in repair for 15 mm dia fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed by Engineer-in-Charge. |
| 88 | S&F in repair SS soap dish complete all as specified & directed. |
| 89 | S&F in repairs Vitreous China squatting pan 'Orissa' pattern,size 580x440 mm white with integral foot rests (excluding flushng cistern and flush pipe) and all as directed by Engneer-n Charge. |
| 90 | S&F in repairs 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with linlet,ball valve, float and handle including brackets, With flush pipe complete all as specified and directed. |
| 91 | S&F in repair 15mm bore brass CP basin mixer for mixing hot and cold water fixed as per manufacture's mannual, with long shunk and cup washers, screwed both ends for iron pipes or for unions complete all as specified and directed. |
| 92 | S&F in repair wall mixer 3 in 1 chromium plated, (L- bend with long bend) with over head shower provision screwed for iron pipes 15mm bore complete all as specified and directed. |
| 93 | S&F in repair 15mm bore brass CP sink mixer for mixing hot and cold water fixed as per manufacture's mannual, with long swan neck and cup washers, screwed both ends for iron pipes or for unions complete all as specified and directed. |
| 94 | S&F in repair Corner Glass Shelf (with Bracket) complete all as specified and directed. |
| 95 | S&F in repair Glass Shelf 600mm Long (with Bracket) complete all as specified and directed. |
| 96 | S&F in repair Towel Ring Square/Round complete all as specified and directed. |
| 97 | S&F in repair Towel Rack with Lower Hanger (Stainless Steel) with hook complete all as specified and directed. |
| 98 | BLANK |
| 99 | S&F in repair 32/40 mm spring type PVC waste pipe fixed to WHB & Sink etc complete all as specified and directed. (Note: minimum length of each pipe should not be less than 0.80RM) |
| 100 | S&F in repairs vitreous china Wash hand basin, white, flat back size 550 x 400mm including brackets waste brass chromium plated with long screwed shanks and fly nuts 32mm size bore of pipe complete all as specified and directed. |
| 101 | S&F in repair vitreous china counter top wash basin, white, of size 410x410x160 mm / 570x420x195 mm / 615x415x150 mm including coupling, bottle trap/waste pipe complete all as specified and directed. |
| 102 | S&F in repair vanity box (floor or wall mounted) of HDHMR of size 580x450x680 mm or equivelent with table top basin and including all connected accessories like waste pipe, coulping complete all as specifies and directed. |
| 103 | S&F in repair Vitreous china wash down water closet pan (pedestal pattern) excluding flushing cistern and flush pipe, including fixing of water closet complete with plastic water closet seat black/white closed pattern witrh flat bottom and cover and mild steel chromium plated or aluminised hinging device. |
| 104 | S&F in repair Vitreous china wash down water closet pan wall hung WC FLS - IVY- 5951 with PP seat cover, hinges, accessories set, size 360x545x365 set jaquar or other equivelent including flushing cistern and fixed with brass screw complete all as specified and as directed. |
| 105 | S&F in repairs vitreous china floor mounted WC (Cascade) one piece type (white) including connecetion in drain etc incl water closet seat cover CP health faucet, flushing cistern, with P or S trap with all fitting and fixture complete all as specified and as directed . |
| 106 | S&F in repairs health faucet chromium plated with 1.50m CP long flexible pipe and chromium plate nuts completed all as spd Make - Cera/ hindware or equivalent approved. |
| 107 | S&F in repairs cast copper alloy CP toilet paper holder fixed with plug and brass screw completed all as specified. |
| 108 | S&F in repair brass spindle half turn suitable for 15 mm bib cock / stop cock/ concealed stop cock/ angle cock complete all as specified and directed. |
| 109 | S&F in repair brass spindle half turn suitable for jaquar / hindware fancy type fitting wall Mixer/ Basin Mixer / Sink Mixer etc complete all as specified and directed. |
| 110 | S&F in repair internal fittings of flushing cistern suitable for one piece cascade type or wall Hung type water closet system complete all as specified and directed. |
| 111 | S&F in repairs over head shower rose CP Brass with shower arm for 15mm bore pipe of size 150x150mmcomplete all as specified and directed. |
| 112 | S&F in repair looking mirror of selected quality sheet glass 5.5 mm thick designer with chromium plated brass screw and cup washer complete all as specified and directed. |
| 113 | Cleaning and removing all scale and dirt, etc from PVC water tanks 500 to 1000 Ltr capacity from mouth of circulating pipes with suitable chemical or solvent as per manufacturer's instruction duly taking care not to damage etc including disconnecting, reconnecting & refixing water tanks in position complete. |
| 114 | Cleaning and removing all scale and dirt, etc from RCC water tanks of high rise bldgs (upto 8th storey) 20000 Ltr to 30000 Ltr capacity from mouth of circulating pipes with suitable chemical or solvent as per manufacturer's instruction duly taking care not to damage etc including disconnecting, reconnecting & refixing pipes in position complete. |
| 115 | S&F in repair Rotational moulded polyethylene water storage tanks 500 lts capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia PTMT ball valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed |
| 116 | S&F in repair Rotational moulded polyethylene water storage tanks 1000 lts capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia PTMT ball valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed |
| 117 | S&F in repair PVC tank cover for 500/1000 Ltrs complete including locking arrangement complete all as specified and as directed by Engineer-in-Charge. |
| 118 | S&F in repair CPVC water tubing 20 mm bore pipe, SDR 11 including provision of all fittings and connected completed in concealed and surface, along with primer & slovent cement for joint as per ASTM D 2564, pipe material shall be as per ASTM D 1785, fitting/ flanges shall be as per ASTM D2467 all as specified and directed by Engr-in-charge. |
| 119 | S&F in repair 40 mm GI Tubes medium grade' galvanised, with all fitting and fixed complete to walls or laid in floors all as specified and directed by Engr-in-charge. |
| 120 | S&F in repair 50 mm GI Tubes medium grade' galvanised, with all fitting and fixed complete to walls or laid in floors all as specified and directed by Engr-in-charge. |
| 121 | S&F in repair 80 mm GI Tubes medium grade' galvanised, with all fitting and fixed complete to walls or laid in floors all as specified and directed by Engr-in-charge. |
| 122 | S&F in repair 40 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all as specified and directed by Engr-in-charge. |
| 123 | S&F in repair 50 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all as specified and directed by Engr-in-charge. |
| 124 | Disposal of building rubbish/malba, similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading and disposal at an approved Municipal dumping ground outside Defence land (MoD land), for all leads and all lifts, complete all as specified and as directed by the Engineer-in-Charge.Notes:1. Photographic Evidence: The contractor shall submit clear photographic evidence in support of disposal of building rubbish/malba, similar unserviceable, dismantled or waste materials, indicating the condition of the site before loading, during transportation and after unloading at the approved Municipal dumping ground. The photographs shall preferably be geo-tagged and date-stamped and shall form part of the record for verification and payment purposes. 2. Certification by Engineer-in-Charge: Completion of whole work in this BOQ shall be deemed to have been achieved only after certification by the Engineer-in-Charge that no building rubbish/malba, similar unserviceable, dismantled or waste materials have been left at the site and that the site has been thoroughly cleared and cleaned to his satisfaction. 3. Each load shall comprise a minimum carrying capacity of 5.00 cubic metres (Cum). Payment under this item shall be made on a per-load basis for loads conforming to the above minimum capacity and duly verified by the Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 01, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysDec 04, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender