Tender For special Repair / Replacement Of Lt Panel And Connected Wks At Certain Locations Under Ge (Mis) Mhow
Tender Value
43.67 Lakhs
Estimated cost
Bid Submission
01 Dec 2026
15 days left
EMD
87500
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Indore → Madhya Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair / Replacement Of Lt Panel And Connected Wks At Certain Locations Under Ge (Mis) Mhow
BOQ
| Sl. No. | Item Description |
| 1 | M&L for fabrication, supply, installation, testing and commissioning CPRI approved electrical cubical control panel board (in replacement) factory assembled made outdoor type feeder pilar box double door type wheather and vermin proof fabricated of 3.15 mm CRCA MS Sheet of suitable size, 3 phase 4 wire 415 V AC 50Hz complete duly painted with powder coating complete with locking arrangement, earthing termimal with suitable rating aluminum strips for incoming/outgoing MCCB's including and mounting measuring instrument such as Volt meter, Ammeter, selector switch, CTs phase indicator lamp with holder, toggle switches and backelite fuse cut outs etc including incoming and outgoing cables connections with suitable cable glands and end termination including grouting of feeder pillar box 60 cm above ground level by providing 90 cm long angle iron size 50x50x6mm welded onall four corner embedded in PCC (1:2:4) using 20mm graded upto 30cm Complete in all respects as specified and directed by the Engineer-in-Charge. The feeder pillar box shall comprise the following components:-(a) High conductivity aluminium busbar (Set of 4 strips), 4 Nos TPN of suitable for 1600 Amps rating ,(RYB) for phase and 1 No for neutral mounted on DMC support with heat shrink sleeve-1 Set.(b) Phase indication lamp, LED type(set of 3) -1 Set , Make: AE / L&T / Schneider / make as per Particular Specification (list of Make) as approved by GE.(c) Ammeter digital type having measuring range (0-500) Amps with CTs etc including rotary switch to measure load of each phase. Make: AE / L&T / Schneider / make as per Particular Specification (list of Make) as approved by GE. |
| 2 | (d) Volt meter digital type having measuring range (0-500) volt with rotary switch to measure voltage of phase R.Y.B make : AE / L&T / Schneider / make as per Particular Specification (list of Make) as approved by GE.(e) Grouting of panel including earth work as required PCC (1:3:6) type D-2 using 20 mm gradeded stone & plastering with (1:4) cement sand etc complete. (f) INCOMMING: MCB 4 Pole, 415 V, Manual Drawout type with microprocessor release of capacity 1000 Amps spreader both side as Incomming control device : 01 Nos. (g) OUTGOING: MCCB 3 Pole, 415 V, with Microprocessor release 400 Amps with breaking capacity 36 KA & spreader both side as outgoing cotrol device : - 02 No. (01 Nos Spare), (h) MCCB 4, pole 36 KA with adjustable thermal setting, 415V, 250 Amp & spreader both side as outgoing cotrol device : - 02 Nos. (i) MCCB 4, pole 36 KA with adjustable thermal setting, 415V, 200 Amp & spreader both side as outgoing cotrol device : - 02 Nos. (j) MCCB 4, pole 36 KA with adjustable thermal setting, 415V, 160 Amp & spreader both side as outgoing cotrol device : - 02 Nos. (k) MCCB 4, pole 16 KA with adjustable thermal setting, 415V, 125 Amp & spreader both side as outgoing cotrol device : - 02 Nos. |
| 3 | M&L for fabrication, supply, installation, testing and commissioning CPRI approved electrical cubical control panel board (in replacement) factory assembled made outdoor type feeder pilar box double door type wheather and vermin proof fabricated of 3.15 mm CRCA MS Sheet of suitable size, 3 phase 4 wire 415 V AC 50Hz complete duly painted with powder coating complete with locking arrangement, earthing termimal with suitable rating aluminum strips for incoming/outgoing MCCB's including and mounting measuring instrument such as Volt meter, Ammeter, selector switch, CTs phase indicator lamp with holder, toggle switches and backelite fuse cut outs etc including incoming and outgoing cables connections with suitable cable glands and end termination including grouting of feeder pillar box 60 cm above ground level by providing 90 cm long angle iron size 50x50x6mm welded onall four corner embedded in PCC (1:2:4) using 20mm graded upto 30cm complete in all respects as specified and directed by the Engineer-in-Charge. The feeder pillar box shall comprise the following components:-(a) High conductivity aluminium busbar (Set of 4 strips), 4 Nos TPN of suitable for 1000 Amps rating ,(RYB) for phase and 1 No for neutral mounted on DMC support with heat shrink sleeve-1 Set.(b) Phase indication lamp, LED type(set of 3) -1 Set, Make: AE / L&T / Schneider / make as per Particular Specification (list of Make) as approved by GE. (c) Ammeter digital type having measuring range (0-500) Amps with CTs etc including rotary switch to measure load of each phase : AE / L&T / Schneider / make as per Particular Specification (list of Make) as approved by GE. |
| 4 | (d) Volt meter digital type having measuring range (0-500) volt with rotary switch to measure voltage of phase R.Y.B make : AE / L&T / Schneider / make as per Particular Specification (list of Make) as approved by GE.(d) Volt meter digital type having measuring range (0-500) volt with rotary switch to measure voltage of phase R.Y.B make : AE / L&T / Schneider / make as per Particular Specification (list of Make) as approved by GE.(e) Grouting of panel including earth work as required PCC (1:3:6) type D-2 using 20 mm gradeded stone & plastering with (1:4 )cement sand etc complete. (f) INCOMMING: MCB 4 Pole, 415 V, Manual Drawout type with microprocessor release of capacity 630 Amps spreader both side as Incomming control device : 01 No. (g) OUTGOING: MCCB 3 Pole, 415 V, with Microprocessor release 400 Amps with breaking capacity 36 KA & spreader both side as outgoing cotrol device : - 02 Nos. (01 No Spare) (h) MCCB 4, pole 36 KA with adjustable thermal setting, 415V, 250 Amp & spreader both side as outgoing cotrol device : - 05 Nos. (j) MCCB 4, pole 36 KA with adjustable thermal setting, 415V, 200 Amp & spreader both side as outgoing cotrol device : - 01 No. |
| 5 | M&L for fabrication, supply, installation, testing and commissioning CPRI approved electrical cubical control panel board (in replacement) factory assembled made outdoor type feeder pilar box double door type wheather and vermin proof fabricated of 3.15 mm CRCA MS Sheet of suitable size, 3 phase 4 wire 415 V AC 50Hz complete duly painted with powder coating complete with locking arrangement, earthing termimal with suitable rating aluminum strips for incoming/outgoing MCCB's including and mounting measuring instrument such as Volt meter, Ammeter, selector switch, CTs phase indicator lamp with holder, toggle switches and backelite fuse cut outs etc including incoming and outgoing cables connections with suitable cable glands and end termination including grouting of feeder pillar box 60 cm above ground level by providing 90 cm long angle iron size 50x50x6mm welded onall four corner embedded in PCC (1:2:4) using 20mm graded upto 30cm complete in all respects as specified and directed by the Engineer-in-Charge. The feeder pillar box shall comprise the following components:-(a) High conductivity aluminium busbar (Set of 4 strips), 4 Nos TPN of suitable for 1600 Amps rating ,(RYB) for phase and 1 No for neutral mounted on DMC support with heat shrink sleeve-1 Set.(b) Phase indication lamp, LED type(set of 3) -1 Set, Make: AE / L&T / Schneider / make as per Particular Specification (list of Make) as approved by GE. (c) Ammeter digital type having measuring range (0-500) Amps with CTs etc including rotary switch to measure load of each phase :AE / L&T / Schneider / make as per Particular Specification (list of Make) as approved by GE. |
| 6 | (d) Volt meter digital type having measuring range (0-500) volt with rotary switch to measure voltage of phase R.Y.B make : AE / L&T / Schneider / make as per Particular Specification (list of Make) as approved by GE.(e) Grouting of panel including earth work as required PCC (1:3:6) type D-2 using 20 mm gradeded stone & plastering with (1:4 )cement sand etc complete. (f) INCOMMING: ACB 4 Pole, 415 V, Manual Drawout type with microprocessor release of capacity 1000 Amps spreader both side as Incomming control device : 01 No. (g) OUTGOING: MCCB 3 Pole, 415 V, with Microprocessor release 400 Amps with breaking capacity 36 KA & spreader both side as outgoing cotrol device : - 02 Nos. (01 Nos Spare) (h) MCCB 4, pole 36 KA with adjustable thermal setting, 415V, 250 Amp & spreader both side as outgoing cotrol device : - 04 Nos. |
| 7 | M&L for fabrication, supply, installation, testing and commissioning CPRI approved electrical cubical control panel board (in replacement) factory assembled made outdoor type feeder pilar box double door type wheather and vermin proof fabricated of 3.15 mm CRCA MS Sheet of suitable size, 3 phase 4 wire 415 V AC 50Hz complete duly painted with powder coating complete with locking arrangement, earthing termimal with suitable rating aluminum strips for incoming/outgoing MCCB's including and mounting measuring instrument such as Volt meter, Ammeter, selector switch, CTs phase indicator lamp with holder, toggle switches and backelite fuse cut outs etc including incoming and outgoing cables connections with suitable cable glands and end termination including grouting of feeder pillar box 60 cm above ground level by providing 90 cm long angle iron size 50x50x6mm welded onall four corner embedded in PCC (1:2:4) using 20mm graded upto 30cm complete in all respects as specified and directed by the Engineer-in-Charge. The feeder pillar box shall comprise the following components:-(a) High conductivity aluminium busbar (Set of 4 strips), 4 Nos TPN of suitable for 630 Amps rating ,(RYB) for phase and 1 No for neutral mounted on DMC support with heat shrink sleeve-1 Set.(b) Phase indication lamp, LED type(set of 3) -1 Set, Make: AE / L&T / Schneider / make as per Particular Specification (list of Make) as approved by GE.(c) Ammeter digital type having measuring range (0-500) Amps with CTs etc including rotary switch to measure load of each phase : AE / L&T / Schneider / make as per Particular Specification (list of Make) as approved by GE. |
| 8 | (d) Volt meter digital type having measuring range (0-500) volt with rotary switch to measure voltage of phase R.Y.B make : AE / L&T / Schneider / make as per Particular Specification (list of Make) as approved by GE.(e) Grouting of panel including earth work as required PCC (1:3:6) type D-2 using 20 mm gradeded stone & plastering with (1:4 )cement sand etc complete. (f) INCOMMING: ON LOAD change over switch 415V, 4 pole of capacity 400 Amps as Incomming control device : 02 Nos. (g) OUTGOING:MCCB 4, pole 36 KA with adjustable thermal setting, 415V, 250 Amp & spreader both side as outgoing cotrol device : - 02 Nos. (h) MCCB 4, pole 36 KA with adjustable thermal setting, 415V, 200 Amp & spreader both side as outgoing cotrol device : - 01 No. |
| 9 | Supply, fixing ( in replacement ), connecting to electrical system & testing of Busbar panel board ,cubical type for out door use, made out of 3.15 mm thick CRCA sheet factory made, totally enclosed of size not less that 900x600x500mm and supported with 4 Nos MS Angle legs , duly painted with two coats of powder coated paint over one coat of red oxide primer effectively PVC gaket and sealed mounted on PCC blocks double door type with locking arragnedment with handle at front and openable at front &back bothe side with required hinges heavy duty, compartemtalised suitably including provision for tapping incoming & outgoing electric connections with suitable size of aluminium lugs glands and comprising of the following accessories :- (a) High conductivity aluminium busbar (Set of 4 strips), 4 Nos TPN of 300 amps rating (RYB) for phase and 1 No for neutral mounted on DMC support with heat shrink sleeve-1 Set.(b) Phase indication lamp, LED type(set of 3) -1 Set, Make: AE / L&T / Schneider / make as per Particular Specification (list of Make) as approved by GE.(c) Ammeter digital type having measuring range (0-300) Amps with CTs etc including rotary switch to measure load of each phase : AE / L&T / Schneider / make as per Particular Specification (list of Make) as approved by GE.(d) Volt meter digital type having measuring range (0-500) volt with rotary switch to measure voltage of phase R.Y.B make : AE / L&T / Schneider / make as per Particular Specification (list of Make) as approved by GE.(e) MCCB 4, pole 36 KA with adjustable thermal setting, 415V, 250 Amp- 02 Nos. (f) Grouting of panel including earth work as required PCC (1:3:6) type D-2 using 20 mm gradeded stone & plastering with (1:4) cement sand etc complete |
| 10 | Supply, fixing & testing of LT distribution panel board (in replacement), made out of 2 mm thick MS sheet of size not less than 600x450x200mm duly painted with two coats of synthetic enamelled paint over one coat of red oxide primer wall mounted/semi-grouted in wall with locking arrangement, double door type, compartmentalised and provision for tapping incoming & outgoing electric connections with suitable size of lugs, glands, one MCCB will be mounted on proper din railes and comprising of the followings :-(a) Aluminium busbar chamber TPN of 200 amps rating (set of 4 strips)(b) Phase indication lamp-set of 3, Make: AE / L&T / Schneider / make as per Particular Specification (list of Make) as approved by GE.(c) MCCB 4 pole 415 Volts, 50 Hz, 100 amps rating, 25 KA breaking capacity - 01 No.(Incomming )(d) MCB TPN 63 A -2 No and MCB SPN 32 A -3Nos as out going cotrol |
| 11 | S&F (in replacement) following items in the existing out door/ indoor LT panels and connection with using aluminum lugs/ferruls incl disconnection & connection of cable and making necessary alteration in panel/door using welding wk and cutting as required for proper fixing & connection complete all as specified and directed. as below :-(a) MCCB 4pole 125 amps rating, 16 KA breaking capacity with spreader at both side |
| 12 | (b) MCCB 4 pole150/160 amps rating, 36 KA breaking capacity with spreader at both side |
| 13 | (c) MCCB 4 pole250 amps rating, 36 KA breaking capacity with spreader at both side |
| 14 | (d) MCCB 4 Pole 100 amps rating, 16 KA breaking capacity, 415 Volt |
| 15 | (e) MCB TPN 100 amps, 'C' series, 415 volt |
| 16 | (f) Volt meter (0 to 500 volts) anolog type with selector switch for three phase |
| 17 | (g) Amp meter (0 to 500 amps) anolog type, witch selector switch for three phase measurement . |
| 18 | (h) CTs of existing ratio and capacity fixed in LT panels and connect with ammeter |
| 19 | (j) Microprocessor based MCCB 4pole 250 amps rating, 36 KA breaking capacity with spreader at both side |
| 20 | Supply, laying, jointing and testing in replacement of underground LT cable XLPE insulated ,screened PVC bedded , galvanised steel strip or wire armoured electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 185 Sqmm 3.5 Core aid in trenches/ducts/along poles/ through pipe under road etc all as specified and directed by Engr-in-Charge. |
| 21 | Supply, laying, jointing and testing in replacement of underground LT cable XLPE insulated ,screened PVC bedded , galvanised steel strip or wire armoured electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 95 Sqmm 3.5 Core aid in trenches/ducts/along poles/ through pipe under road etc all as specified and directed by Engr-in-Charge. |
| 22 | Supply, laying, jointing and testing in replacement of underground LT cable XLPE insulated ,screened PVC bedded , galvanised steel strip or wire armoured electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 70 Sqmm 3.5 Core laid in trenches/ducts/along poles/ through pipe under road etc all as specified and directed by Engr-in-Charge. |
| 23 | Supply, laying, jointing and testing in replacement of underground LT cable XLPE insulated ,screened PVC bedded , galvanised steel strip or wire armoured electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 Sqmm 3.5 Core laid in trenches/ducts/along poles/ through pipe under road etc all as specified and directed by Engr-in-Charge. |
| 24 | Supply, laying, jointing and testing in replacement of underground LT cable XLPE insulated ,screened PVC bedded , galvanised steel strip or wire armoured electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 Sqmm 3.5 Core laid in trenches/ducts/along poles/ through pipe under road etc all as specified and directed by Engr-in-Charge. |
| 25 | Supply, laying, jointing and testing in replacement of underground LT cable XLPE insulated ,screened PVC bedded , galvanised steel strip or wire armoured electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 Sqmm 3.5 Core laid in trenches/ducts/along poles/ through pipe under road etc all as specified and directed by Engr-in-Charge. |
| 26 | Excavation in trenches not exceding 1.5m wide and noe exceding 1.0 sq m on plan and not exceding 1.5m depth and getting out soft soil complete all as specified and directed. |
| 27 | Returing filling in including spreading leveling watering and well ramming in layer not exceding 25 cm soft/loose soil complete all as specified and directed. |
| 28 | Removing excavated material not exceding 50 m and depostingwhere directed. at a level not exceding 1.50 m above the starting pointall as specified and directed. |
| 29 | M&L for sand cushioning to underground cable (8 cm thick before laying and 15 cm thick after laying the cable complete all as specified and directed.Note : Punned thickness shall be maesured. |
| 30 | Supply and laying flyash brick (Modular size) laid dry and flat across the length of cable for protection of cable complete all as specified and directed. |
| 31 | S&F in replacement GI tubing, light grade, with all necessary fittings, laid in trenches/under road crossings/fixed on poles or walls/under floors, including suitable mild steel flat iron clamps of required size, complete all as specified and directed, for the following sizes:-(a) 80mm bore |
| 32 | (b) 50mm bore |
| 33 | M&L for boring holes under road, hard standing without damaging surface for 80/50/40 mm dia GI pipe etc complete all as specified and directed. |
| 34 | M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground.(earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level connecting to galvanised strip 32x6mm as earth lead by means of bolts, check nuts and washers of GI and earth wire protected by provision of GI pipe light grade,40mm bore including provn of concrete pit in PCC (1:2:4) type B-1 using 20mm graded crushed stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 KG/Sqm) and frame of angle iron 25 X 25 X 3mm with lugs 2 Nos and with 6mm dia MS bar handle made to shape, GI medium grade 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exeeding 50 mtr, all as per electrical plate No 3 of SSR 2009 Part-I and connection all as specified and testing on completion. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 01, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysDec 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender