Defence Statutory Bodies & Commissions/Committees Closing in 9 days TDR #58469290

Tender For Repair/Maint Of Old Ci/Di/Gi Pipe Line And Connected Items At Technical Area Under Af Stn Ambala Under Ge (Af) Ambala

Issued by Statutory Bodies & Commissions/Committees · Ambala, Haryana
Tender Value
45 Lakhs
Estimated cost
Bid Submission
30 Nov 2026
9 days left
EMD
90000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Ambala → Haryana
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender for Repair/Maint Of Old Ci/Di/Gi Pipe Line And Connected Items At Technical Area Under Af Stn Ambala Under Ge (Af) Ambala

BOQ

Name of Work:- REPAIR/MAINT OF OLD CI/DI/GI PIPE LINE AND CONNECTED ITEMS AT TECHNICAL AREA UNDER AF STN AMBALA UNDER GE (AF) AMBALA
Sl. No. Item Description
1Surface excavation in soft/loose soil not exceeding 30 cm deep and averaging 15cm deep and getting out complete all as specified and directed
2Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.50 m deep in soft/loose soil for laying and taking out water pipe lines, including getting out excavated material, dressing and levelling bottom surface to the required level and slope, complete all as specified and directed. Note: 1. During excavation, if any footpath, PCC, plinth protection, valve chamber, road, drain or other existing structure is damaged, the same shall be made good and restored by the contractor to the satisfaction of the Engineer-in-Charge. The quantity of such rectification/restoration work shall be measured and paid separately under the relevant items of work. 2.The required cleaning and removal of grass and vegetation along the proposed pipeline alignment/working area shall be carried out by the contractor as part of the work, including disposal of the cleaned material as directed by Engr. in Charge.3.Wherever mechanical excavation is not feasible or is prohibited due to site conditions, proximity to existing utilities, structures, or safety considerations, the contractor shall carry out manual excavation only, as directed by the Engineer-in-Charge. 4. The contractor shall use suitable utility locating and detection tools (for water lines, electrical cables and other underground services) before and during excavation. Any damage caused to existing electrical infrastructure, cables, ducts, water supply lines or allied services during excavation shall be repaired and restored to its original condition by the contractor at his own cost. In case the repair/restoration is not completed within 24 hours from the time of damage, a penalty of ₹2,000 per day shall be recovered from the contract amount for each day of delay.
3Returning, filling, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with excavated soil, complete all as specified and directed.
4Removal of surplus soil to a distance not exceeding 50 metres and depositing the same where directed, at a level not exceeding 1.5 metres above the starting point, complete all as specified and directed.
5Taking up DI water mains of 150 mm dia bore, including all fittings, with spigot and socket ends and lead joints, including burning out of joints and recovering lead, complete all as specified and directed.
6Supplying and laying in trenches centrifugally cast (spun) ductile iron pressure pipes of 150 mm dia for water supply, with spigot and socket ends, Class ‘K-9’, conforming to IS: 8329:2000 (latest version), suitable for push-on rubber gasket jointing, with internal cement mortar lining using Portland Slag Cement conforming to IS: 455:1989 and external metallic zinc coating as per Annex ‘A’ of IS: 8329, finished with a layer of bituminous coating as per Annex ‘C’, duly ISI marked, in any standard length, including testing and commissioning, complete all as specified and directed. Make: Electrosteel / Tata / Jindal
7Taking up CI water mains of 100 mm dia bore, including all fittings, with spigot and socket ends and lead joints, including burning out of joints and recovering lead, complete all as specified and directed.
8Supplying and laying in trenches centrifugally cast (spun) ductile iron pressure pipes of 100 mm dia for water supply, with spigot and socket ends, Class ‘K-9’, conforming to IS: 8329:2000 (latest version), suitable for push-on rubber gasket jointing, with internal cement mortar lining using Portland Slag Cement conforming to IS: 455:1989 and external metallic zinc coating as per Annex ‘A’ of IS: 8329, finished with a layer of bituminous coating as per Annex ‘C’, duly ISI marked, in any standard length, including testing, complete all as specified and directed. Make: Electrosteel/Tata/Jindal.
9Taking up CI water mains of 80 mm dia bore, including all fittings, with spigot and socket ends and lead joints, including burning out of joints and recovering lead, complete all as specified and directed.
10Supplying and laying in trenches centrifugally cast (spun) ductile iron pressure pipes of 80 mm dia for water supply, with spigot and socket ends, Class ‘K-9’, conforming to IS: 8329:2000 (latest version), suitable for push-on rubber gasket jointing, with internal cement mortar lining using Portland Slag Cement conforming to IS: 455:1989 and external metallic zinc coating as per Annex ‘A’ of IS: 8329, finished with a layer of bituminous coating as per Annex ‘C’, duly ISI marked, in any standard length, including testing, complete all as specified and directed. Make: Electrosteel/Tata/Jindal.
11Taking up DI water mains of 150 mm dia bore, including all fittings, with flanged ends including disconnecting pipes and fittings complete all as specified and directed.
12Supplying and laying in trenches centrifugally cast (spun) ductile iron pressure pipes of 150 mm dia for water supply, with flanged ends, Class ‘K-9’, conforming to IS: 8329:2000 (latest version), suitable for rubber gasket jointing, with internal cement mortar lining using Portland Slag Cement conforming to IS: 455:1989 and external metallic zinc coating as per Annex ‘A’ of IS: 8329, finished with a layer of bituminous coating as per Annex ‘C’, duly ISI marked, in any standard length, including testing, complete all as specified and directed. Make: Electrosteel/Tata/Jindal.
13Taking up DI water mains of 100 mm dia bore, including all fittings, with flanged ends including disconnecting pipes and fittings complete all as specified and directed.
14Supplying and laying in trenches centrifugally cast (spun) ductile iron pressure pipes of 100 mm dia for water supply, with flanged ends, Class ‘K-9’, conforming to IS: 8329:2000 (latest version), suitable for rubber gasket jointing, with internal cement mortar lining using Portland Slag Cement conforming to IS: 455:1989 and external metallic zinc coating as per Annex ‘A’ of IS: 8329, finished with a layer of bituminous coating as per Annex ‘C’, duly ISI marked, in any standard length, including testing and commissioning, complete all as specified and directed. Make: Electrosteel/Tata/Jindal.
15Taking up DI water mains of 80 mm dia bore, including all fittings, with flanged ends including disconnecting pipes and fittings complete all as specified and directed.
16Supplying and laying in trenches centrifugally cast (spun) ductile iron pressure pipes of 80 mm dia for water supply, with flanged ends, Class ‘K-9’, conforming to IS: 8329:2000 (latest version), suitable for rubber gasket jointing, with internal cement mortar lining using Portland Slag Cement conforming to IS: 455:1989 and external metallic zinc coating as per Annex ‘A’ of IS: 8329, finished with a layer of bituminous coating as per Annex ‘C’, duly ISI marked, in any standard length, including testing, complete all as specified and directed. Make: Electrosteel / Tata / Jindal.
17Supply, laying and jointing in repair/replacement of heavy duty CI/DI fittings such as bends (any type, radius and angle), tapers of any type (straight, bend, increasing, decreasing or double socket, etc.), tee pieces, single branch, Y-junctions, double branch, crosses (all socketed or socket and spigot or all flanged or one end flanged and other ends spigot/socketed), collars, caps, plugs, MJ collar couplings, mechanical joints etc., conforming to relevant IS specifications, for pipe sizes up to 200 mm bore, including excavation of leaking/damaged area, cutting of existing pipeline wherever required, jointing with suitable rubber gasket/lead jointing material, testing for leak-proof operation, returning, filling, disposal of surplus excavated material and restoration of disturbed surfaces, complete all as specified and directed by Engineer-in-Charge. Make: Electrosteel /Jindal / Tata.
18Taking down old unserviceable GI pipe 150/100/80/50/25/20mm dia complete all as specified and as directed.
19Supply, laying, testing and jointing GI tubing of 150 mm dia bore, medium grade, conforming to IS:1239, including all fittings, laid in trenches, complete all as specified and directed.
20Supply, laying, testing and jointing GI tubing of 100 mm dia bore, medium grade, conforming to IS:1239, including all fittings, laid in trenches, complete all as specified and directed.
21Supply, laying, testing and jointing GI tubing of 80 mm dia bore, medium grade, conforming to IS:1239, including all fittings, laid in trenches, complete all as specified and directed.
22Supply, laying, testing and jointing GI tubing of 50 mm dia bore, medium grade, conforming to IS:1239, including all fittings, laid in trenches, complete all as specified and directed.
23Supply, laying, testing and jointing GI tubing of 25 mm dia bore, medium grade, conforming to IS:1239, including all fittings, laid in trenches, complete all as specified and directed.
24Supply, laying, testing and jointing GI tubing of 20 mm dia bore, medium grade, conforming to IS:1239, including all fittings, laid in trenches, complete all as specified and directed. Note for Item Nos. 19 to 24: If existing wall plastering/PCC/bricks wall or any other surface is damaged/disturbed during repair/replacement of the GI pipeline, the affected surface/area shall be made good to match the existing condition. The quantity for such making good work shall be measured and paid separately under the relevant items, complete all as specified and directed.The contractor shall deploy dedicated supervisor along with the required qualified workers for deployment at site. The supervisor shall also action the job card from concerned section before commencement of the work and ensure that the work is carried out as per the instructions of Engir-in-Charge for smooth functioning & satisfactory completion of the maintenance work The supervisor shall be responsible the conditioning the entry and exit formalities of all Contractors labour/ workers, including permission from the concerned Air Force Police/ security persual, obtaining and arranging (temporary pass) entry permits and ensuring compliance with all security istructions applicable to the technical area.
25Crossing of pipeline GI/CI/DI 20mm dia to 150mm dia by trenchless technology using Horizontal Directional Drilling (HDD) method for laying water supply pipeline complete, setting out, preparation of entry and exit pits, drilling of pilot bore, reaming to required diameter, insertion of GI/DI pipe as specified, bentonite slurry circulation, alignment control, protection of existing underground utilities, testing and commissioning. The work shall include deployment of HDD rig of suitable capacity, hydraulic power pack, mud mixing and recycling system, air compressor, DG set, excavator, dewatering pumps, welding equipment, survey instruments and all allied machinery, labour, consumables and safety arrangements. The crossing shall be executed without disturbing the taxi track pavement, operational area or existing services and shall include restoration of entry and exit pits, disposal of excavated material, complete in all respects as specified and directed by the Engineer-in-Charge.
26Supply of Orthotolidine (OT) Solution for residual chlorine testing in potable water, packed in 500 ml sealed bottle, suitable for rapid colorimetric determination of free and total residual chlorine in drinking water, clear and stable reagent formulation providing accurate and reliable test results, compatible with standard chlorine testing comparators and field testing kits, supplied in leak-proof, chemically resistant bottle with proper labeling complete all as specified and directed. Make: RMCO / Systronics / Hach.
27Taking down old unserviceable sluice valve 150/100/80mm dia complete all as specified and as directed.
28Supply, fixing, testing and commissioning Double flanged non-rising stem type cast iron sluice valve suitable for 150 mm dia bore pipe with hand wheel and suitable for pressure rating of PN :1.6 duly drilled holes for fixing of nuts and bolts, stem made of high tensile brass ISI marked and conforming to IS:14846/IS 780 including rubber gasket, nuts, bolts and washers complete all as specified and directed.Make: Zoloto / Leader / Kirloskar
29Supply, fixing, testing and commissioning Double flanged non-rising stem type cast iron sluice valve suitable for 100 mm dia bore pipe with hand wheel and suitable for pressure rating of PN :1.6 duly drilled holes for fixing of nuts and bolts, stem made of high tensile brass ISI marked and conforming to IS:14846/IS 780 including rubber gasket, nuts, bolts and washers complete all as specified and directed. Make: Zoloto / Leader / Kirloskar
30Supply, fixing, testing and commissioning Double flanged non-rising stem type cast iron sluice valve suitable for 80 mm dia bore pipe with hand wheel and suitable for pressure rating of PN :1.6 duly drilled holes for fixing of nuts and bolts, stem made of high tensile brass ISI marked and conforming to IS:14846/IS 780 including rubber gasket, nuts, bolts and washers complete all as specified and directed. Make: Zoloto / Leader / Kirloskar
31Taking down old unserviceable NRV 150/100/80mm dia complete all as specified and as directed.
32Supply, fixing, testing and commissioning Double flanged cast Iron swing check type reflux (Non Return) valve 150 mm dia single door pattern conforming to IS : 5312 (part – I)–1969, duly drilled holes for fixing nuts and bolts including rubber gasket, nuts, bolts and washers complete all as specified and directed. Make: RMCO/Kartar/Sant
33Supply, fixing, testing and commissioning Double flanged cast Iron swing check type reflux (Non Return) valve 100 mm dia single door pattern conforming to IS : 5312 (part – I)–1969, duly drilled holes for fixing nuts and bolts including rubber gasket, nuts, bolts and washers complete all as specified and directed. Make: RMCO/Kartar/Sant
34Supply, fixing, testing and commissioning Double flanged cast Iron swing check type reflux (Non Return) valve 80 mm dia single door pattern conforming to IS : 5312 (part – I)–1969, duly drilled holes for fixing nuts and bolts including rubber gasket, nuts, bolts and washers complete all as specified and directed. Make: RMCO/Kartar/Sant
35Taking down old unserviceable CI/DI butterfly valve 100/80mm dia complete all as specified and as directed.
36Supply, fixing and replacement of 100 mm nominal bore CI/DI Butterfly Valve, lever operated, wafer type, pressure rating PN-16, conforming to relevant IS standards and ISI marked, having epoxy coated cast iron/ductile iron body, stainless steel shaft, nitrile rubber (NBR/EPDM) resilient seat lining and suitable for insertion between flanged pipe ends. The work shall include dismantling and removal of existing valve, supply and fixing of new butterfly valve complete with MS tail pieces/flanged adaptors on both sides, cutting, welding, drilling, alignment, jointing and fabrication works as required at site, providing and fixing rubber/fibre insertion gaskets, nuts, bolts, washers and all associated fittings and accessories. The item shall also include testing for leakage, commissioning, painting of disturbed MS portions with one coat of red oxide primer and two coats of synthetic enamel paint, and making good the installation for satisfactory operation. Complete with all labour, tools, tackles, consumables, transportation and incidental charges, complete in all respects as specified and directed by the Engineer-in-Charge.Makes: Sant / Zoloto / Kartar / Kirloskar
37Supply, fixing and replacement of 80 mm nominal bore CI/DI Butterfly Valve, lever operated, wafer type, pressure rating PN-16, conforming to relevant IS standards and ISI marked, having epoxy coated cast iron/ductile iron body, stainless steel shaft, nitrile rubber (NBR/EPDM) resilient seat lining and suitable for insertion between flanged pipe ends. The work shall include dismantling and removal of existing valve, supply and fixing of new butterfly valve complete with MS tail pieces/flanged adaptors on both sides, cutting, welding, drilling, alignment, jointing and fabrication works as required at site, providing and fixing rubber/fibre insertion gaskets, nuts, bolts, washers and all associated fittings and accessories. The item shall also include testing for leakage, commissioning, painting of disturbed MS portions with one coat of red oxide primer and two coats of synthetic enamel paint, and making good the installation for satisfactory operation. Complete with all labour, tools, tackles, consumables, transportation and incidental charges, complete in all respects as specified and directed by the Engineer-in-Charge. Makes: Sant / Zoloto / Kartar / Kirloskar
38Taking down old unserviceable gate valve 50/40/25/20mm dia complete all as specified and as directed.
39Supply, fixing and testing of 50 mm dia Gun Metal Gate Valve, screwed body ends with cast iron hand wheel, conforming to IS: 778-1984 and ISI marked, including cutting of existing GI pipe line, removal of unserviceable valve (if any), insertion and fixing of new valve with all necessary fittings, jointing materials, testing for proper operation and leakage, complete in all respects, all as specified and directed by the Engineer-in-Charge.Make: Zoloto/Leader/Scud
40Supply, fixing and testing of 40 mm dia Gun Metal Gate Valve, screwed body ends with cast iron hand wheel, conforming to IS: 778-1984 and ISI marked, including cutting of existing GI pipe line, removal of unserviceable valve (if any), insertion and fixing of new valve with all necessary fittings, jointing materials, testing for proper operation and leakage, complete in all respects, all as specified and directed by the Engineer-in-Charge.Make: Zoloto/Leader/Scud
41Supply, fixing and testing of 25 mm dia Gun Metal Gate Valve, screwed body ends with cast iron hand wheel, conforming to IS: 778-1984 and ISI marked, including cutting of existing GI pipe line, removal of unserviceable valve (if any), insertion and fixing of new valve with all necessary fittings, jointing materials, testing for proper operation and leakage, complete in all respects, all as specified and directed by the Engineer-in-Charge.Make: Zoloto/Leader/Scud
42Supply, fixing and testing of 20 mm dia Gun Metal Gate Valve, screwed body ends with cast iron hand wheel, conforming to IS: 778-1984 and ISI marked, including cutting of existing GI pipe line, removal of unserviceable valve (if any), insertion and fixing of new valve with all necessary fittings, jointing materials, testing for proper operation and leakage, complete in all respects, all as specified and directed by the Engineer-in-Charge. Make: Zoloto/Leader/Scud
43Demolition of existing valve chamber of any size complete all as specified and as directed.
44M&L for masonry valve pit chamber of up to size 1500x1500x1050mm internal size complete with excavation, earth work and 100mm thick PCC foundation in cement concrete 1:4:8 type D-2 using 40mm graded mechanically crushed stone aggregates and brick work with sub class 'B' bricks with in cement mortar 1:6, 15mm thick plastering in cement mortar 1:4 internally including 5mm thick MS Sheet cover and angle iron frame of suitable size and two coats of synthetic enamel paint over one coat of red oxide primer complete with locking arrangement complete all as specified and directed.
45M&L for run lead joints for 200 mm dia cast iron spun pipes/fittings, including burning out existing defective joints, recovering serviceable lead, refixing and pouring molten lead in joints, caulking, yarn packing and making the joints completely watertight and leak proof, complete all as specified and directed by Engineer-in-Charge.
46M&L for run lead joints for 150 mm dia cast iron spun pipes/fittings, including burning out existing defective joints, recovering serviceable lead, refixing and pouring molten lead in joints, caulking, yarn packing and making the joints completely watertight and leak proof, complete all as specified and directed by Engineer-in-Charge.
47M&L for run lead joints for 100 mm dia cast iron spun pipes/fittings, including burning out existing defective joints, recovering serviceable lead, refixing and pouring molten lead in joints, caulking, yarn packing and making the joints completely watertight and leak proof, complete all as specified and directed by Engineer-in-Charge.
48M&L for run lead joints for 80 mm dia cast iron spun pipes/fittings, including burning out existing defective joints, recovering serviceable lead, refixing and pouring molten lead in joints, caulking, yarn packing and making the joints completely watertight and leak proof, complete all as specified and directed by Engineer-in-Charge.
49M&L for making joints with rubber/fibre board gaskets for flanged pipes and fittings suitable for 150 mm bore cast iron pipes, including replacement of unserviceable/corroded nuts, bolts, washers and providing all necessary jointing materials, tightening, alignment and testing for completely leak-proof performance, complete all as specified and directed by Engineer-in-Charge.
50M&L for making joints with rubber/fibre board gaskets for flanged pipes and fittings suitable for 100 mm bore cast iron pipes, including replacement of unserviceable/corroded nuts, bolts, washers and providing all necessary jointing materials, tightening, alignment and testing for completely leak-proof performance, complete all as specified and directed by Engineer-in-Charge. Please Enable Macros to View BoQ information
51M&L for making joints with rubber/fibre board gaskets for flanged pipes and fittings suitable for 100 mm bore cast iron pipes, including replacement of unserviceable/corroded nuts, bolts, washers and providing all necessary jointing materials, tightening, alignment and testing for completely leak-proof performance, complete all as specified and directed by Engineer-in-Charge. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58469290
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE 45 Lakhs
LAST DATE 30-11-2026
Authority
Authority Name Military Engineer Services
Work Description Tender for Repair/Maint Of Old Ci/Di/Gi Pipe Line And Connected Items At Technical Area Under Af Stn Ambala Under Ge (Af) Ambala
Basic Detail
Tender No GE AF/AMB-T-41/2026-27
Bidding Type Tender
Location
City Ambala
State Haryana
Key Dates
Publish Date 09 Nov 2026
Submission Date 30 Nov 2026
Open Date 02 Dec 2026
Finance
Tender Value 45 Lakhs
Tender Fee 500
EMD 90000
Exemption Available
Document List
12eba00d-3899-4603-8a92-713fc2a05288.html
41TenderPages.pdf
BOQ_895148.xls
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 09, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Nov 30, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 9 days
Dec 02, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 11 days

Tender Documents

Download All (ZIP) ↓
html

12eba00d-3899-4603-8a92-713fc2a05288.html

pdf

41TenderPages.pdf

xls

BOQ_895148.xls

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender