Tender For Provn Of Tennis Arena With 02 X Synthetic Tennis Court Adjacent To Sport Complex At Nda,Khadakwasla And Installation Of Perforated Aluminium Grill In New B Tech Cell And Exam Cell Building At Nda Khadakwasla
Tender Value
42.84 Lakhs
Estimated cost
Bid Submission
30 Nov 2026
17 days left
EMD
86000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Pune → Maharashtra
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of Tennis Arena With 02 X Synthetic Tennis Court Adjacent To Sport Complex At Nda,Khadakwasla And Installation Of Perforated Aluminium Grill In New B Tech Cell And Exam Cell Building At Nda Khadakwasla
BOQ
| Sl. No. | Item Description |
| 1 | M & L for following ASPHALT BASE FOR OUTDOOR RECREATIONAL SURFACE 1 A. Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in any type of soilB. Rolling and consolidating formation surfaces in cutting by power roller exc 8 ton and n.exc 12 ton capacity C. M&L for Anti termite treatment, Treating the top surface of earth at the rate of 5 litres of emulsion per square metre of surface D. 7.5cm thick (compacted thickness) WBM, with coarse aggregates of grading 2 (63 to 40mm size) or of grading 3 (50 to 20mm size), spread, rolled and consolidated to gradient and camber required. WBM to be densely compacted by keying and inter locking the stones to ensure that no settlement takes place. E. M&L for 30 mm compacted thickness premixed bituminous macadam laid, spread using mechanical paver with 4% binder content by weight of total mix, using paving bitumen VG - 30 grade by weight of total mix , rolled & compacted to required gradient and camber using power roller of capacity exceeding 8 tonne but not exceeding 12 tonne etc over anf including tack coat 5 kg/10sqm all as specified & directed. F. M&L for 20 mm consolidated thickness Bituminous premix Semi-dense asphaltic concrete with 5.5% binder (Paving Bitumen VG-30 Grade) content by weight of total mix,by using mechanical pavers and vibratory rollers ,spread, rolled and consolidated to required camber and gradient over and including 2.5 kg/sqm tack coat all as specified& directed by Engineer-In- Charge G. Premixed sand seal coat with 0.06 cu.m. of sand mixed with 6.8 kg of bitumen, applied and rolled to a uniform smooth surface. H. Provn of open saucer drain of min depth 0.15 m and 0.15 m wide of PCC 1:2:4, 50 mm thick to drain of water on the edge of court I. Provn of 200 mm thick blockwork wall, ht of wall 200 mm over 75 mm thick PCC 1:4:8 including rendering in CM 1:4 on edge to support the court. |
| 2 | M & L for following PRIMER: 1 Primer layer (KDF ITF APPROVED) will be of the Concrete Primer which is a high strength acrylic primer that helps in enhancing the adhesion of the court acrylic coatings. RESURFACER:1 The next layer (KDF ITF APPROVED) will be of Acrylic Resurfacer which is the 100% acrylic based emulsion blended with selected fibers and fillers to be used for smoothing rough pavements. CUSHION COAT: 2 The next coating (KDF ITF APPROVED )will be of Rubber Cushion which helps in giving smother finish and better level of comfort. 2. ULTRA CUSHION COAT: 2 Layers of Acrylic Synthetic KDF cushion for asphalt or concrete surfaces in preparation for Acrylic ITF approved system PRECOAT: After that, 2 Layer ( ITF APPROVED)the Color Coating is provided applied which is wear resistance. It is a 100% acrylic emulsion consisting of brilliant pigments and quality polymers that are blended into a highly concentrated form. OVERLINE : 100% Acrylic Synthetic FLOOR (KDF) based high hiding line paints. |
| 3 | M & L for following Tennis Movable and adjustable post Made of 75 to 100 mm round powder coated steel pipe with fibre weight with non tearing cover and wheel for easy movement as per ITF standard |
| 4 | M & L for following Chain Link Fencing Work(3 Mtr Height) Including provn of a wicket gateVertical Poll - 72 X 72 X 3mm - MS Pole at 2.5 m spacingHorizontal poll - 50 X 50 X 3mm - MS Pole at 1.5 m spacingChanging Net - 50 X 50 X 3mm - Gala MSVertical Pole Post hole - 45 X 45 X 60 CM- PCC Work1 Coat Primer and 2 coat painting to complete steel surface |
| 5 | Excavation in trenches in soft/loose soil not exceeding 1.5 m wide and not exceeding 1.5 m in depth for laying of cable etc. and for foundation of poles, stays etc. n exc 10 sqm on plan and n exc 1.5 in depth and getting out complete all as specified. |
| 6 | Description all as per Serial item Nos '1' above but depth exceeding 1.5 mtr and not exceeding 3.00 mtr. |
| 7 | Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick of soft/loose soil in trenches/pit complete all as specified and directed. |
| 8 | Removal of surplus soil to a distance not exceeding 50 m and depositing where directed not exceeding 1.5 m above the starting point complete all as specified and directed. |
| 9 | Supply and laying XLPE Insulated armoured heavy duty electric cables with aluminium conductor, 1100 volts grade, in trenches /fixed on wall /floor of cross sectional area 10sqmm 4 core complete all as directed |
| 10 | Supply and laying XLPE Insulated armoured heavy duty electric cables with aluminium conductor, 1100 volts grade, in trenches /fixed on wall /floor of cross sectional area 6sqmm 4 core complete all as directed |
| 11 | Supply, errecting & fixing in replacement in steel pole type 410 SP 31 (9 Mtr) true vertical position pole conforming to IS-1678 of 9 mtr long, at complete as specified & directed .Note : (i) MS channel is to be welded at equal interval for climbing up on poles for repairs and on top for mounting of LED flood Lights all as specified and directed. (ii) MS channel will be measured and paid separately. |
| 12 | Material & labour cement concrete 1:4:8 type D-2 using 40 mm graded crushed stone aggregate as in foundation complete all as specified and directed |
| 13 | Material & labour PCC 1: 3 : 6 type C-1 (using 20 mm graded mechanically crushed stone aggregate) as in mass concrete including necessary form work complete all as specified and directed. |
| 14 | Material & labour for Cross Arms bracings supports, clamps, eye hook and back plates fabricated from structural steel sections including pole clamps stay clamps, D clamps nuts, bolts , washers welding bending cold or hot drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of aluminium paint complete all as specified and directed. |
| 15 | M&L for earthing complete with galvanized steel earth plate electrode size 600 mm x 600 mm x 6.3 mm thick buried directly in ground vertically in a pit of depth not less than 2.25 mtr below ground levels with top edge of the earth plate not less than 1.5 mtr below normal ground level surrounded from all sides by mixture of charcoal and common salt and electrode connected to and including galvanized earth lead 4.0 mm dia by means of bolts, nuts, check nuts and washers of galvanized including GI protection pipe medium grade 15mm dia connected to main earth wire on pole or control board and GI pipe medium grade 20 mm dia bore for watering funnel with wire mesh. RCC cover with frame, PCC chamber pit with PCC 1:3:6 type C-2 excavation and earth work all as shown in electrical plate No 3 connected to earthing test point all as specified or indicated including testing on completion all as specified and directed |
| 16 | S&F thermoplastic cable junction box with weather proof for out door installation IP 66/67 protection grade of two terminals suitable for cable entry 10 -25 sqmm of size 205x255x112mm including necessary clamps for fixing arrangement complete all as specified and directed.Make Hensel Cat No KF2525G |
| 17 | Supply only PVC insulated sheathed wire 1.5 Sqmm ,3 single core with copper conductor of colour red,black and green for connection street light fittings from over head line/pole boxes complete all as specified and directed. |
| 18 | Supply, fixing and testing energy saving, environmental friendly, long life, exclusive innovative die-cast aluminium IP65 flood light 250 Watt with high power leds as light source, suitable for highmast and general purpose lighting complete all as specified and directed. |
| 19 | M&L for outdooor type street light timer box made out of CRCA sheet 3mm thick,ip65 ,double door with aprons,dust,vermin,weather proof with two coats of epoxy paint on one coat of red oxide primer comprising of phase indicator lamps=03 nos, Insulated aluminium busbar 100A =04 nos, cable entry provisions for one incoming and two outgoing cables , Incoming MCCB 40A,four pole,415V=01 no complete with spreader terminals ,Astronomical timer switch Model T2DDT7 Make : L&T or equivalent in Schneider,contactor 32A=02 nos,MCBDP40A =03 nos mounted on DIN channel, selector switch for Auto/mannual & OFF function incl internal wiring with 6sqmm multistranded copper conductor. The panel shall be self supported on angle iron frame made out of 4omm x 6mm angle iron 30cm on ground and 60 cm above surface all as directed by engineer in charge. |
| 20 | Supply and laying 40 x 32 mm outer & inner dia, double walled corrugated (DWC) HDPE duct pipe confirming to IS-16205 Pt-24 with antirodent and non flame propogating properties of approved colour complete with fittings i.e.coupler,Tee, elbow clamp for cable protection of size 10 to 16 Sqmm 3.5 core complete all as specified and directed by Engr-In-Charge. |
| 21 | M&L for aluminium frame work as in doors, partitions and windows using powder coated (Powder coating 50 micron) aluminium sections including provision of glazing clips, hinges, handles, etc complete all as specified and directed by Engr-in-Charge. Notes:(i ) All the aluminium sections provided under this item shall be measured and converted into weight for payment with the designated unit weight mentioned in the manufacturer's catalogue for the corresponding aluminium sections/fittings.(ii) The rate quoted deemed to include necessary grouting/ embedding of the aluminium frames/supports into floors/ walls and making good the disturbed surfaces to match with the existing surfaces and provision of necessary rubber gaskets.(iii) Particle board/glass panels shall be measured and paid separately. |
| 22 | S & F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and directio of Engineer in-charge. Using Designation No.DG: 117 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 09, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 30, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysDec 02, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender