Tender For Special Repairs And Replacement Of Fire Fighting System At South Jetty Naval Base Kochi
Tender Value
1.23 Crore
Estimated cost
Bid Submission
07 Dec 2026
25 days left
EMD
1.98 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ernakulam → Kerala
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repairs And Replacement Of Fire Fighting System At South Jetty Naval Base Kochi
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of Brick work or stone/boulder masonry, laid built in cement mortor all as specified and directed. . |
| 2 | M & L Precast cement concrete solid block type B1 1:2:4 (using 20mm graded stone aggregate) exc 10cm in width and setting in cement morter 1:6 all as specified and directed. |
| 3 | M&L for 10mm thick cement mortar plaster on brick wall in concrete surface in CM 1:6 finished even and smooth wihout using extra cement, all as specified and directed. |
| 4 | M&L for preparation of new plastered surfaces of walls and applying two coat of antifungal weather proof paint of required shade over a coat of primer using modern tools, and spray technique all as specified and directed. |
| 5 | Dismantling of plain or corrugated steel sheeting, any guage, thickness from roof covering all as specified and directed. |
| 6 | S& F Pre-painted galvalume aluminium zinc coating (AZ-150) GI based corrugated steel sheet/ Manglore tile pattern 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws all as specified and directed. |
| 7 | Dismantling wrought iron or mild steel work / mild steel gates of any description not otherwise provided for all as specified and directed. |
| 8 | Supply & Fix Roof trusses (framed), trussed, purlins, crane gantries,rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces,base plates,wind tight flat iron, cleats etc.Fe 410-W (Gde-E-250) Quality 'A' complete all as specified and as directed. |
| 9 | S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete etc. Fe-410-W(Gde- E-250) quality-A all as specified and directed. |
| 10 | S&F Wire netting size 25mm x 25mm of galvanised steel wire 1.40mm dia fixed with tinned tacks of wire staples all as specified and directed. |
| 11 | M & L Preparation of new steel surfaces and applying two coats of synthetic enamal paint over a coat of red oxide all as specified and directed. |
| 12 | Supply & Fix EURO GUARD PRO SQUARE UPVC RAINWATER GUTTER (180 MM), with all necessary fittings, clamp, joints, end cap,corner drop centre drop, etc joining compounds, nut & bolts or screw etc and fixing in position at any height all as specified and directed. |
| 13 | S & F in repair PVC (SWR) pipes 110mm Dia single socketed in any length with rubber ring joints fixed to walls all as specified and directed. |
| 14 | S & F in repair PVC (SWR) Bend 110 mm Dia all as specified and directed. |
| 15 | M&L for cement concrete 1:2:4 type B2 (40 mm size graded aggregate ) in post holes all as specified and directed. |
| 16 | Supply Fix testing and commissioning of centrifugally spun ductile cast iron high pressure pipes, Class K-9, conforming to IS 8329 and its latest amendments, fixed in walls/floors at south jetty naval Base Kochi, internally lined with double-thickness cement-mortar lining using sulphate-resisting cement suitable for seawater service and provided with a suitable seawater-resistant seal coat. External surface shall be provided with Metallic Zinc Coating as per annex A of IS 8329 with finishing layer of Bituminous Coating as per Annex C of IS 8329 followed by a high-build, seawater-resistant protective epoxy coating system. All flanges, joints and other wetted areas shall be suitably protected against seawater corrosion. Pipes shall be complete with seawater-resistant EPDM gaskets, jointing materials, supports,, complete as specified and directed as following sizes:Note : DI pipes fittings and brackets will be measured and paid seperately. |
| 17 | 150 mm nominal dia |
| 18 | 100 mm nominal dia |
| 19 | 80 mm nominal dia |
| 20 | Supply, laying, jointing, testing and commissioning of SS 316L seawater intake pipe, minimum 4 mm wall thickness, including SS 316L fittings, flanges, bends, EPDM gaskets, fasteners, supports, welding, pickling/passivation, hydrostatic/leak testing, flushing and all necessary accessories, complete as directed by the Engineer-in-Charge. |
| 21 | 200 mm dia |
| 22 | 150 mm dia |
| 23 | 100 mm dia |
| 24 | 80 mm dia |
| 25 | S&F, testing and commissioning of wafer/lug type Ductile iron with heavy duty epoxy coating, qualified for seawater services butterfly valves, gear operated PN 1.6 MPa (PN16), suitable for sea water service, conforming to the applicable IS/EN standard, with corrosion-resistant body, stainless-steel disc/stem and replaceable resilient elastomer seat, complete with operating mechanism/gear box, flanges, bolts, nuts, washers, gaskets and all accessories, tested for body and seat leakage and complete as specified and directed as following sizes: |
| 26 | 200 mm dia |
| 27 | 150 mm dia |
| 28 | 80 mm dia |
| 29 | 50mm dia |
| 30 | S&F, testing and commissioning of non-return/dual-plate Ductile iron with heavy duty epoxy coating check valve PN16, suitable for sea water service, of approved type and conforming to the applicable IS standard, with corrosion-resistant construction, complete with flanges, rubber gaskets, GI/SS bolts, nuts, washers and all accessories, including testing for leakage and satisfactory operation, complete as specified and directed. |
| 31 | 200mm dia |
| 32 | 150mm dia |
| 33 | 80mm dia |
| 34 | Supply, installation, testing and commissioning of high-pressure, reinforced rubber expansion joint for pump vibration isolation in a raw seawater pipeline, suitable for continuous seawater service at an operating pressure of 16 bar. The joint shall be manufactured from seawater-compatible EPDM rubber with suitable high-strength reinforcement, with high tensile synthetic textile fabric with embanded wire reinforcement where required. corrosion-resistant flanges, of carbon steel and necessary control rods or restraints and fastners as required .The complete assembly shall be rated for the design pressure, including pump-starting and and shall accommodate the specified vibration and movement. Flange drilling and dimensions shall match the existing pipeline., tested and complete as specified and directed. |
| 35 | 200 mm dia |
| 36 | 150 mm dia |
| 37 | 100 mm dia |
| 38 | 80 mm dia Please Enable Macros to View BoQ information |
| 39 | 80 mm dia Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 09, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 25 daysDec 14, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 32 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender