Tender For Special Repair To Bldg No Cr/1 At Piru Singh Enclave Under Ge Panagarh
Tender Value
57.48 Lakhs
Estimated cost
Bid Submission
10 Dec 2026
28 days left
EMD
1.11 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Purba Bardhaman → West Bengal
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair To Bldg No Cr/1 At Piru Singh Enclave Under Ge Panagarh
BOQ
| Sl. No. | Item Description |
| 1 | SCH A PART-I : B/R PORTION |
| 2 | M&L Brick work with fly ash bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6 including demolition of old unserviceable brickwork, complete all as specified and directed. |
| 3 | M&L Brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick built in Cement Mortar 1:4 including demolition of old unserviceable brickwork, complete all as specified and directed |
| 4 | M&L rendering 5mm thick cement plaster in Cement Mortar 1:3 on ceiling including finished even and smooth without using extra cement including taking down old unserviceable plaster work, complete all as specified and directed. |
| 5 | M&L rendering 15 mm thick cement plaster in Cement Mortar 1:6 on fair faces brick or concrete surfaces of wall including finished even and fair including taking down old unserviceable plaster work, complete all as specified and directed. |
| 6 | Supply only integral Liquid water proofing compound complete all as specified and directed. |
| 7 | M&L preparation of new plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed. |
| 8 | M&L two coats of Acrylic distemper over a coat of alkali resistant primer newly plastered surfaces of walls, to achieve a level and smooth to wall, preparing wall with putty to a uniform smooth surface before applying primer, of any description including preparation of surfaces all as specified and directed. |
| 9 | M&L complete removal of existing treatment of any description on old wall surface and applying 3 mm thick wall care putty and rubbing with sand paper to achieve a level and smooth to wall and applying two coats of acrylic Emulsion distemper over a coat of alkali resistance primer complete all as specified and directed. |
| 10 | M&L complete removal of existing treatment of any description from old plastered surfaces of ceilings and applying two coats of white wash including preparation complete all as specified and directed. |
| 11 | S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed. |
| 12 | M&L preparation of new painted steel and iron surfaces of any description exc 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide complete all as specified and directed. |
| 13 | M&L 100 mm thick Plain Cement Concrete type B-1, (1:2:4) using 20mm graded stone aggregate as in receiving floor Finishes including taking down old unserviceable concrete work,complete all as specified and directed. |
| 14 | M&L Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with & including 15mm thick screed bed of cement mortar 1:6 including dismantling of old unserviceable tiles work with backing plaster, complete all as specified and directed. |
| 15 | M&L Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with & including 10mm thick cement mortar in 1:4 backing plaster including dismantling old unserviceable tile work with backing plaster complete all as specified and directed. |
| 16 | M&L glazed ceramic colour joint free tiles tiles in vertical surface exc 0.42 Sqm but n. exc 1.00 sqm set and jointed in neat cement slurry over 10 mm thick 1:3 cement mortar plaster and pointed in coloured cement to match including dismantling old unserviceable tile work complete all as specified and directed. |
| 17 | M&L Machine cut kota stone slab flooring 18-20mm thick over cement screed laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing with & including 15mm thick screed bed of cement mortar 1:6 including dismantling of old unserviceable tiles work with backing plaster, complete all as specified and directed. |
| 18 | M&L Kota stone slab 18-20mm thick in riser of steps, skirting, dado & pillar over plaster & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing with & including 20mm thick screed bed in cement mortar 1:4 including dismantling the old one complete all as specified and directed. |
| 19 | M&L green Marble work 16-18 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in CEMENT MORTAR(1:3) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of Makrana Adanga complete including dismantling the old one all as specified and directed. |
| 20 | M&L 16-18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, including screed bed of 20mm thick in 1:3 cement mortar including dismantling the old one, complete all as specified and directed. |
| 21 | M&L Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations, complete all as specified and directed. |
| 22 | M&L 75 mm thick Plain Cement Concrete 1:3:6 type C2(using 20 mm graded stone agg) finished as in plinth protection surfaces, even and smooth without using extra cement, etc complete all as specified and directed.[Note: The rate includes the length not exceeding 3m length with joint to be filled with bituminous mastic filling comprising a mixture of 1 part of heated industrial bitumen 85/25 grade and two part of heated sand. the toe of plinth protection of size 75mm deep and 75mm wide] |
| 23 | Taking down chowkat or frames exc 1.5 sqm but n exc 4.0 sqm each with shutter (without taking off shutters from the frame) complete all as specified and directed. |
| 24 | Taking down Chowkats or frames not exc. 1.5 sq. m each with shutters (without taking off shutters from the frames) complete all as specified and directed. |
| 25 | Taking Down shutter exc 2 sq. m each complete all as specified and directed. |
| 26 | S&F factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multi-chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wire mesh shall be paid separately)Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made complete all as specified and directed. |
| 27 | S&F Providing and fixing factory made uPVC white colour fixed window, area not exceeding 1.00sqm each made of extruded profiles with wall thickness of 2.3mm(+-0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 +–0.2mm thick, galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 5mm thick glazing with selected quality glass complete all as specified and directed.(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories Net opening will be measured for payment purpose.) |
| 28 | S&F Sheet glass 3 mm thick, ordinary quality & glazing with oil putty in square but n.exc 0.5 sq.m in each pane complete all as specified and directed. |
| 29 | S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed. |
| 30 | S&F Solid PVC door frame of size 50mm x 95mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. tube, in opening as per specification & drawing complete all as specified and directed. |
| 31 | S&F Factory made solid moulded PVC door shutter 28 to 30mm thick (style) with 2,4 or 6 raised panel design with 2 mm thick 3D wood grain moulded PVC sheet polyurethane painted on the front face & 2 mm thick plain colour PVC sheet on back face with particle face supply & fixing on frame, as per specification & drawing complete all as specified and directed. |
| 32 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50X100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non-toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and directed. |
| 33 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50X125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and directed. |
| 34 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative panelled decorative flush door shutter one side plain on other side of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/wheat husk) and non-toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 35 | S&F factory made single extruded WPC (Wood Polymer Composite) wire gauzed i.e. panel shutter will be wire mesh in lieu WPC , the wire gauze shall be warped on additional square 8mm MS Solid tube and this tube shall be welded to MS frame complete all as specified and directed. |
| 36 | S&F stainless steel Butt hinges 100mm size, with galvanised mild steel hinge pin, anodised and fixed, complete all as specified and directed. |
| 37 | S&F stainless steel Butt hinges 75mm size, with galvanised mild steel hinge pin, anodised and fixed, complete all as specified and directed. |
| 38 | S&F Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed. |
| 39 | S&F extruded Aluminium alloy handles 150mm size, cast type, anodised complete all as specified and directed. |
| 40 | S&F extruded Aluminium alloy handles 100 mm size, cast type, anodised complete all as specified and directed. |
| 41 | S&F Aluminium, anodised, barrel tower bolts 150mm long of extruded section complete all as specified and directed. |
| 42 | S&F Aluminium, anodised, barrel tower bolts 75mm long of extruded section complete all as specified and directed. |
| 43 | S&F in repairs 150 mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 44 | S&F in repairs Hasp and staple, 75 mm long safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed. |
| 45 | Dismantling of wrought iron or mild steel work af any description not otherwise provided for complete all as specified and directed. |
| 46 | S&F 18 mm thick PVC sheet one side laminated, (density 600 kg/cum), fixed in kitchen cabinet and like, complete all as specified and directed. |
| 47 | M&L for Extra over rates for PVC lipping 0.45mm thick over PVC Sheet, fixed to PVC sheet with necessary fittings, complete all as specified and directed. |
| 48 | Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 and cutting chases for concealed water tubing and making good of groves for concealed GI tube, cutting not exc 10cm girth complete all as specified and directed. |
| 49 | Supply & laying of CPVC pipes of 16 mm outer dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including taking down old unserviceable one complete all as specified and directed. |
| 50 | Supply & laying of CPVC pipes of 20 mm outer dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including taking down old unserviceable one complete all as specified and directed. |
| 51 | S&F in repairs vitreous china squatting pan 'Orissa' pattern size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing system anti syphonage pipe etc complete all as specified and directed |
| 52 | S&F in repairs PVC valve less, syphonic action type, low level PVC flushing cistern 10 ltr cap, white with flush pipe & all fitting complete all as specified and directed |
| 53 | S&F in repairs Vitreous China Ware Wash hand basin white flat back size 550mmx400mm without pedestal, cutting for and pinning ends of brackets or erecting stand including necessary PVC outlet pipe, CP coupling 32mm dia complete all as specified and directed |
| 54 | S&F in repairs PVC connections 15 mm size with PTMT nuts of length 600mm complete all as specified and directed. |
| 55 | S&F in repairs 32mm dia Waste coupling, brass , chromium plated for glazed ware , basins , etc. with long screwed shanks and fly -nuts , flange end bedded in red lead cement and other end fixed complete all as specified and directed. |
| 56 | S&F in repairs sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm etc, complete all as specified and directed. |
| 57 | S&F in repairs chromium plated Swivel shower roses with shower arm, 125 mm size including fixing to steel pipe or union etc complete all as specified and directed. |
| 58 | S&F in repairs tubular towel rail 20 mm dia ‘D’ type 60 cm long between flanges of brass chromium plated including brackets. complete all as specified and directed. |
| 59 | S&F in repairs Corner glass self-assembly consisting of 5.5 mm thick glass sheet glass self 200mm with CP bracket guard and railing complete all as specified and directed. |
| 60 | S&F in repairs waste coupling of 40mm dia brass chromium plated for glaze ware sinks, basins, etc with long screwed shanks and fly nuts flange and bedded in red lead cement and other end fixed complete all as specified and directed |
| 61 | S&F in repairs grating doom 125mm dia with waste hole of PTMT minimum weight 40 Gms complete all as specified and directed. |
| 62 | S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall/laid in floor including taking down old unserviceable one complete all as specified and directed. |
| 63 | S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall/laid in floor including taking down old unserviceable one complete all as specified and directed. |
| 64 | S&F in repairs 110mm bore PVC (SWR) bends any radius complete all as specified and directed. |
| 65 | S&F in repairs 75mm bore PVC (SWR) bends any radius complete all as specified and directed. |
| 66 | S&F in repairs 110mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed. |
| 67 | S&F in repairs 75mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed. |
| 68 | S&F in repairs PVC door bends with oval access door (any radius) for 75 mm bore PVC pipes, complete all as specified and directed. |
| 69 | S&F in repairs PVC door bends with oval access door (any radius) for 110 mm bore PVC pipes, complete all as specified and directed. |
| 70 | S&F in repairs 110mm dia PVC (SWR) junction, single (single T) equal or unequal with door access all as specified and directed |
| 71 | S&F in repairs fancy type C.P bib taps cast copper alloy with capston headed handles, screwed down screwed for iron pipe 15 mm bore or for brass ferrule complete fixed in repair complete all as specified and directed. |
| 72 | S&F in repairs 15mm bore Stop valve cast copper alloy screwed down high pressure with capstone headed handle chromium plated concealed type screwed both ends for iron pipe 15 mm bore or for unions complete all as specified and directed. |
| 73 | S&F in repairs fancy type 15mm dia stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for iron pipe fixed in repair complete all as specified and directed. |
| 74 | S&F in repairs Gun metal, globe or gate valve with iron wheel head, 20 mm bore, screwed both ends for iron pipe complete all as specified and directed. |
| 75 | S&F in repairs angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe complete all as specified and directed. |
| 76 | S&F in repairs Pillar taps, fancy type 15mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. |
| 77 | S&F in repairs toilet paper holder with flat recessed type stainless steel complete all as specified and directed |
| 78 | S&F in repairs soap dish, any type fixed to plugs chromium plated brass screws complete all as specified and directed. |
| 79 | M&L and Providing and laying Water proofing treatment to sunken portion and adjoining walls of kitchen, WC, Bath & Toilet, etc all as specified and directed in following steps:(a) Taking out old unserviceable treatment over sunken floor and clean the surface with wire brush, dirt less with water jet etc (b)Providing and laying water proofing treatment of sunken portions of WCs, bathrooms etc by applying cement slurry mixed with Acrylic based polymer modified cementious composite compound coating of make as approved in Technical instruction 5/2023 (c) First layer of slurry of cement 0.488kg/sqm mixed with acrylic based polymer modified cementious composite compound @0.253kg/sqm . This layer will be allowed to air cure for 4 days. (d)Second layer of slurry of cement @0.242 kg/sqm mixed with acrylic based polymer modified cementious composite compound @0.126kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hrs complete all as specified and directed. |
| 80 | M&L providing rust proof/anti-corrosion treatment to bars :-(i) Cleaning of all exposed bars (new & old) around(ii) Apply a single coat of Rust off & Rust top all-round bars new & old as recommended by the manufacturer.NOTE: Anti corrosive treatment shall be continuous especially in the regions where pitting, imperfections, etc were present on the surface of the bars. It is important that the rear portions of re bars (those towards the concrete substrate) should not be left without coating complete all as specified and directed. |
| 81 | M&L Reinforced Cement Concrete (nominal mix), B1 1:2:4 (using 20 mm graded stone aggregate) in slabs supported on walls, beams and columns, in roofs and in shelves and the like including demolition of old unserviceable RCC, complete all as specified and directed. |
| 82 | M&L Reinforced Cement Concrete (nominal mix), B1 1:2:4 (using 20 mm graded stone aggregate) in chajja including demolition of old unserviceable RCC, complete all as specified and directed. |
| 83 | Formwork to sides of Chullah hoods, chajjas and similar items, for fair finished surface of concrete, all as specified and directed. |
| 84 | Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), for fair finished surface of concrete, all as specified and directed. |
| 85 | M&L Mild steel TMT bars 6mm to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 86 | M & L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 87 | M&L TMT bars but 5mm dia and over upto and including 10mm dia in stirrups, spacers, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in stirrups, spacers and binders complete all as specified and directed. |
| 88 | S&F in repairs soft closing 'O' Degree high grade mild steel, bright finish or electro galvanised for cupboard shutter complete all as specified and directed. |
| 89 | S&F in repairs magnetic catcher for kitchen cabinet shutter as approved by Engr-In-Charge, complete all as specified and directed. |
| 90 | S&F in repairs Chromium Plated bib taps long body cast copper alloy with capston headed handles, screwed down screwed for iron pipe 15 mm bore or for brass ferrule complete fixed in repair complete all as specified and directed. |
| 91 | S & F in repairs wall mixer chromium plated 3 way including telephonic shower arrangement with connecting legs, wall flanges & wall bracket for hand shower complete all as specified and directed. |
| 92 | S&F in repairs MS drapery rod powder coated 25mm internal dia in curtain rod, sample complete all as specified and directed. |
| 93 | S&F MS Powder coated bracket size 150 mm made to shape suitable for holding curtain/ drapery rod of 25 mm dia fixed with PVC rail plugs and MS screws for single/ double rods, complete all as specified and directed. |
| 94 | S&F in repairs stainless steel kitchen plate rack (24''x24''x10'') including necessary fixing/fitting & making good the existing surface complete all as specified and directed. |
| 95 | S&F in repairs Door seal (Snake guard) with Aluminium frame powder coated complete all as specified and directed. |
| 96 | M&L repair to crack portion with jacketing technique, taking down existing plaster up to brick wall surface of min 200 mm wide, cleaning to loose particles on surface of brick work along the length of crack and filling the gap/crack area with PCC 1:1.5:3 type A0 using 12.5 mm aggregate up to brick surface and inserting the welded mesh of size 25 x 25x 2 mm dia along the crack on both side of the wall surface fixed with, drilling holes 10 mm dia on either side of the crack by means of drilling machine throughout the full width of the wall @ 25 cm c/c and insert 8/10 mm dia rod in the drilled holes, welded with horizontal rod to withhold the welded mesh and applying grit plaster 1:1:2 using 4 mm and down aggregate finished even and smooth without using extra cement complete all as specified and directed.(Note: Reinforcement and welded mesh will be measured and paid separately ) |
| 97 | S&F in repairs n.exc 1 sqm area mirror of selected quality glass, mounted on, with chromium plated brass screws and cup washers, complete all as specified and directed. |
| 98 | S&F multipurpose lock 12mm to 25mm thick panel, for cupboard/ cabinet, with brass screws, brass keys fixed to cabinet/cupboard, complete all as specified and directed. |
| 99 | S&F 100mm Brass Handle for cupboard/ cabinet, fixed with SS screws, complete all as specified and directed. |
| 100 | M&L Plain Cement concrete of Type C-1, 1:3:6 (using 40 mm graded stone aggregate) in surface channels and drains, complete all as specified and directed. |
| 101 | S&F Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed, complete all as specified and directed. |
| 102 | SCH A PART-II : INTERNAL ELECTRIFICATION PORTION |
| 103 | Taking down carefully aluminium conductor point wiring (light, fan, socket or power) complete including fittings such as switches, ceiling roses, pendants, regulators ,sockets etc. and removing (except those to be reused shall be kept in safe custody at the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing complete all as specified and directed. |
| 104 | M&L point wiring for light point/ fan point, one light/fan/exhaust fan point controlled by one, one way switch using 1.5 sqmm nominal cross sectional area multistranded copper conductor ,PVC insulated unsheathed FRLSH cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including sheet metal modular box for suitable frame 2 to 8 module size and and 1.5 sqmm nominal cross sectional area multistranded copper conductor FRLSH PVC insulated unsheathed earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed. |
| 105 | All as per item No. 2.02 above but One 3 pin 5 Amps socket out let points with cable 2.5 sqmm on independent board, complete all as specified and directed. |
| 106 | All as per item No. 2.02 above but 5 Amp socket on same board with other switch, with cables 1.5 sqmm size complete all as specified and directed. |
| 107 | All as per item No. 2.02 above but 5 Amp Calling bell point controlled by one way bell switches with other switches complete all as specified and directed. |
| 108 | All as per item No. 2.02 above but one light point conrolled by Two way switches with cables 1.5 sqmm complete all as specified and directed. |
| 109 | M&L point wiring for power point on independent Board controlled by one, one way switch using 4.0 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLSH cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including sheet metal modular box for suitable frame 2 to 8 module size and 4.0 sqmm nominal cross sectional area multistranded copper conductor FRLSH , PVC insulated unsheathed FRLSH cable earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed. |
| 110 | S&F switch piano, flush type, single pole , 5/6 Amps, one way complete all as specified and directed. |
| 111 | S&F socket outlets 2 in 1, 5/6 Amps, 230/240V (for same board) one way complete all as specified and directed. |
| 112 | S&F switch socket combination 2 in 1 multipurpose 5 pin , (6 Amps )(independent board) flush type controlled by one switch complete all as specified and directed. |
| 113 | S&F switch socket combination 5 in 1 , (5/16 Amps) flush type controlled by one switch complete all as specified and directed. |
| 114 | S&F switch piano, flush type, single pole , 16 Amps, one way complete all as specified and directed. |
| 115 | S&F socket outlets 3 pin, 16 Amps flush type 230/240 V complete all as specified and directed. |
| 116 | S&F switch piano type 6 Amps, two way, single phase, complete all as specified and directed. |
| 117 | S&F Bell push switch, flush type,5 amp complete all as specified and directed. |
| 118 | S&F 5-stepped type electronic fan regulator, flush type, 240 Volts ISI marked complete all as specified . |
| 119 | S&F ceiling rose surface bakelite 65 mm x 50 mm three terminal suitable for 230 Volts AC 6 Amps complete all as specified and directed. |
| 120 | S&F 6W surface mounted round LED downlight, aesthetically designed aluminiumdie-cast enclosures, with separate replaceable constant current driver 6 Watts for grid ceiling, including necessary connection, complete all as specified and directed. |
| 121 | S&F Buzzer, Ding dong, AC 230 Volts, single pole 230 volts all as specified and directed. |
| 122 | M&L sub-main wiring with two run of FRLSH PVC insulated unsheathed single core multi-stranded copper conductor of size 4 sqmm and one run of 2.5 sqmm copper conductor as continuity earth wire drawn in and including PVC Conduit concealed of suitable size but not less than 20 mm dia on wall / floor etc, including PVC fittings such as bends Tee and boxes including taking down old unserviceable sub main wiring all as specified and directed.[Note : (i) Two run of 4 sqmm cable, one run of 2.5 sqmm cable, one run of PVC conduit shall be measured and paid as one unit.] |
| 123 | M&L sub-main wiring with two run of FRLSH PVC insulated unsheathed single core multi-stranded copper conductor of size 6 sqmm and one run of 4 sqmm copper conductor as continuity earth wire drawn in and including PVC Conduit concealed of suitable size but not less than 20 mm dia on wall / floor etc, including PVC fittings such as bends Tee and boxes including taking down old unserviceable sub main wiring all as specified and directed[Note : (i) Two run of 6 sqmm cable, one run of 4 sqmm cable, one run of PVC conduit shall be measured and paid as one unit.] |
| 124 | S&F wall LED street/security light fittings 35 watt, 230 volts, AC outdoor type with high pressure die cast aluminium hosing and eat resistant comlet with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed. |
| 125 | S&F LED light fitting 1 x 20 watt box type with same make LED tube rod side connection AC decorative box type 4' long with driver, holder including LED tube connecting up with complete all accessories and connection from ceiling rose with twin core twisted flexible copper conductor cable with suitable size and earthing complete all as specified and directed. |
| 126 | S&F wall mounted Decorative wall light fixture made up of Polycarbonate, suitable for 9 W with 9W LED bulb retrofit LED Lamp B22 base complete all as specified and directed. |
| 127 | S&F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. |
| 128 | S&F LED light fitting mirror light LED Pride Plus Neo Batten 10 W 2 feet. 220 volts AC with holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. |
| 129 | S&F epoxy powder coated sheet metal enclosure for TPN DBs, 4 ways, double door with mounting fitted with bus bar, DIN channel , neutral link and incoming contact, IP-43 complete all as specified and directed. |
| 130 | S&F epoxy powder coated sheet metal enclosure for DBs, double door, Single pole and neutral, 12 ways, with mounting fitted with 200 Amps rated bus bar, DIN channel , neutral link and incoming contact complete all as specified and directed. |
| 131 | S&F MCB 4 pole, 415 volts fixed type 40 to 100 Amps, 'C' Curve with breaking capacity 10 kA complete including necessary connection complete all as specified and directed. |
| 132 | S&F MCB SPN 32 Amps, 'C' curve 10kA, 240 Volts and to be housed in DBs complete including necessary connection all as specified and directed. |
| 133 | S&F MCB SPN 40 Amps, 'C' curve 10kA, 240 Volts and to be housed in DBs complete including necessary connection all as specified and directed. |
| 134 | S&F MCB SP 6-32 Amps, 'C' curve 10kA, 240 Volts and to be housed in DBs complete including necessary connection all as specified and directed. |
| 135 | M&L taking down of ceiling fans of any sweep and transportation to work shop including dismantling for repair/overhauling, oiling, greasing, varnishing and replacement of unserviceable accessories like capacitor, connector etc. After repair re-assembling fan, testing for efficient functioning including hanging it back in position and provn of 0.5 Sqmm copper flexible twin twisted cable (length not exceeding 0.5 metre) from ceiling rose to fan , complete all as specified and directed.[Note: Capacitor and Connector are measured & paid separately] |
| 136 | M&L painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc, including writing MES Number with black synthetic enamel paint, complete all as specified and directed. |
| 137 | Supply only copper conductor for rewinding of the coil of ceiling fan/ exhaust fan with super enamelled copper conductor turn per coil, gauge with existing type including varnish for winding complete all as specified and directed.[Note : BOO shall be ascertained the weight of copper winding used in fan] |
| 138 | Supply only Capacitor 2.5 mfd, 230 Volts, AC, 50 Hz, 440 VAC for ceiling fans complete all as specified and directed. |
| 139 | Supply only ball bearing number 6201 of suitable size for ceiling fans 1200mm to 1400 mm sweep complete all as specified and directed. |
| 140 | Supply only ball bearing number 6202 of suitable size for ceiling fans 1200mm to 1400 mm sweep complete all as specified and directed. |
| 141 | S&F in repairs MS down rod of size 15/20mm dia and length one foot for ceiling fan including electric connection, nut, bolt and clamp as in repair, complete all as specified and directed. |
| 142 | Hanging only ceiling fan (M.D supply) and connecting up including provision of cable from ceilin rose or connector to fan, complete all as specified and directed. |
| 143 | S&F in repairs exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, copper winding of sweep 200mm air flow performance 520-550 cubic metre/ hour, complete all as specified and directed.[Note : (a) Warranty certificate from manufacturer shall be submitted to Engr-in-Charge for claiming the payment(b) Old unserviceable exhaust fan shall be deposited at MES store with receipt voucher] |
| 144 | S&F in repairs PVC exhaust fan refresh air window neo ventilation complete with louvers shutter, voltage 230V, 50 Hz, copper winding of sweep 150mm minimum air delivery 250 cubic metre/ hour, complete all as specified and directed.[Note : (a) Warranty certificate from manufacturer shall be submitted to Engr-in-Charge for claiming the payment(b) Old unserviceable exhaust fan shall be deposited at MES store with receipt voucher] |
| 145 | M&L earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, buried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI wire encased in and including 40 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and Plain Cement Concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and Reinforced Cement Concrete pit cover 50mm thick precast Reinforced Cement Concrete 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I testing of resistance on completion complete all as specified and directed. |
| 146 | SCH A PART-III : EXTERNAL WATER PORTION |
| 147 | S&F Pipes galvanized iron, 25 mm bore “Medium grade”, supplied and fixed complete to walls and ceilings or laid in floors/ trenches complete including necessary fittings such as tees, bends, elbows, sockets, reducers etc as per site requirement including taking up old unserviceable one, complete all as specified and directed.[Note: Excavation and earthwork will be measured and paid separately] |
| 148 | Refixing old steel tubing including cleaning and connections in new or old position (in trenches, on wall/ceiling & floors etc) of 25 mm bore GI pipe including taking up/ down old serviceable GI pipes complete all as specified and directed.[Note: Excavation and earthwork will be measured and paid separately] |
| 149 | S&F gun metal, gate valve ISI marked, 25 mm dia with iron wheel head, screwed both ends for iron pipe and fix complete all as specified and directed. |
| 150 | S&F in repairs capacity 500 Ltrs rotational moulded polyethylene water storage tanks (minimum 3 layered), white, anti bacterial, UV resistant, Threaded lid, anti microbial, 100% virgin food grade plastic, prevent algae growth, anti viral/ bacterial/ fungal/ algae properties, (Cylindrical, vertical with closed top) complete including provision of all inlet outlet overflow and drain pipe fitting including taking down unserviceable tank, complete all as specified and directed. |
| 151 | S&F in repairs of high pressure PTMT float valve with epoxy coated aluminium rod and high density polyethylene ball screwed for iron pipe 20 mm dia with fly nut complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 10, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 28 daysDec 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 36 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender