Defence Statutory Bodies & Commissions/Committees Closing in 14 days TDR #58462864

Tender For Special Repair To Cb-199 Jcos/Or Md Accn Under Ge (Mis) Mhow

Issued by Statutory Bodies & Commissions/Committees · Indore, Madhya Pradesh
Tender Value
48.49 Lakhs
Estimated cost
Bid Submission
01 Dec 2026
14 days left
EMD
97000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Indore → Madhya Pradesh
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender For Special Repair To Cb-199 Jcos/Or Md Accn Under Ge (Mis) Mhow

BOQ

Name of Work:- SPL REPAIR TO CB-199 JCOS/OR MD ACCN UNDER GE (MIS) MHOW
Sl. No. Item Description
1Removing the existing roof treatment of any description completely and remove all the debris old water tanks from site and rubbish off the premises complete all as specified and directed.
2M&L for roughening surfaces of old concrete floor or concrete surfaces by picking, sweeping clean and washing down with water to remove dust, etc.and brushing neat cement slurry with 3 Kg., of cement per square metre complete all as specified and directed.
3M&L for providing cement concrete type B0 1:2:4 (12.5mm graded stone aggregate) as in padding and benching & filletting with water proofing compound complete all as specified and directed.Note: Water proofing compound will be measured and paid separately.
4M&L for screed bed or bedding layer 10 mm thick CM 1:4 for laying floor finishes finished even and smooth without using extra cement with with water proofing compound as in roof slabs complete all as specified and directed. Note: Water proofing compound will be measured and paid separately.
5Supply only integral water proofing compound complete all as specified and directed.
6M&L for water proofing treatment with APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified with non woven polyester matt black finished over compatiable primer at 0.3 litre per sqm, torching the membrane on whole surface uniformly while unrolling the membrane by LPG and sealed with trowel after necessary preparation of surface complete all as per manufactures instructions and finally finished with at coat of bitumastic aluminium paint over the membrane. The over lap joint shall be provided of 100mm in longitudinal direction and 150mm in tranverse direction respectively. All the angles, abutments and the drainage outlets shall be sealed with extra care to ensure full bondage. Note:- (a) WPT shall be carried out either by the manufacturer or by an authorized applicator.
7Demolition of un-reinforced Cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.
8Demolition of cement concrete (reinforced) as in roof, floors (other than ground floor) beams, staircase, landing, chajjas and similar suspended work complete all as specified and directed.
9Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish of the premises complete all as specified and directed by Engr-in-Charge.
10Dismantling of stone slabs of any description or thickness in floors, approaches, dado/Partitions etc complete all as specified and as directed
11M&L for Scratch free, double charged, vitrified ceramic tiles 9 to 10mm thick (square or rectangular) area of each tile not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed.
12M&L for coloured Non Skid ceramic joint free tiles 7 to 8 mm thick (Square/ Rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.18 Sqm, in floors etc,over and including 15 thick screed bed in CM 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tile complete all as specified and as directed.
13S&F for glazed ceramic tiles in vertical surface 450 x 300x 7 mm thick over and including 10 thick plaster in CM 1:4, set and jointed in neat cement slurry and pointed in white or cloured cement complete all as specified and as directed. Note: The rate includes cutting, offsets, etc. complete all work as specified and as directed.
14M&L for machine cut and mirror polished kota stone ( size not less than 550mm x 550mm for flooring & for tread of steps will be in one piece) slab flooring 18 to 20 mm thick over and including 15mm thick cement screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and as directed
15M&L for machine cut and mirror polished kota stone slab 18 to 20 in riser of steps(in one piece), skirting, dado, pillar etc over and including 10mm thick plaster in CM 1:4, jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and as directed
16M&L for hard core of guage n.exc 63 mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.
17M&L for 75mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection laid in panels, finish the top surfaces even and smooth complete including filling the joints with mastic compound complete all as specified and directed
18M&L for 50 mm thick cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) surface finished even and smooth without using extra cement complete all as specified and directed.
19M&L for PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) in foundation, filling and mass concrete, sub base complete all as specified and as directed.
20M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.
21M&L for Pre-cast cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in Kitchen platform and Cover slab for manholes etc set in cement mortor 1:4 including use and waste necessary form work (Reinforced shall be measured and paid seprately) complete all as specified and directed.
22S&F mild steel TMT bars 10mm dia and over, cut to length bent to shap required including cranking, bending spirally for hooping for columnshooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.
23All as per item No 22.00 above but 5mm dia and over upto and including 10 mm dia as in spacers, stirrups and binders complete all as specified and directed.
24M&L for granite slabs 20mm thick machine cut bedded laid over and including cement screed 15mm thick in CM 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab incl grinding moulding rounding chamfering and polishing complete all as specified and directed.
25Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.
26Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.
27M&L for brick work with using flyash bricks modular size, straight or curved on plan exc. 6.00m mean radius built in cement mortar 1:6. etc complete all as specified and directed.
28M&L for brick work with using flyash bricks modular size, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.
29Taking down cement plaster on wall of any description incl racking out joints for key, scrubbing with water etc. complete all as specified and directed.
30M&L for rendering 15 mm thick in cement mortar 1:4 on concrete or brick wall surfaces, finished even and smooth without using extra cement, mixed with WPC @ 3% by weight of cement (WPC measured and paid separately), complete all as specified and directed.
31M&L for rendering 10mm thick in cement mortar 1:6 on Brick wall surfaces, finished even and smooth without using extra cement complete all as specified and directed.
32M&L for rendering 5mm thick in cement mortar (1:3) as in ceilings, concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.
33M&L for 15 mm thick cement plaster in cement mortar 1:4 on brick or concrete surface etc. on wall finished even and smooth without using extra cement complete all as specified and directed.
34Excavation in trenches not exc 1.50 m wide and not exc 1.50 m in depth for foundation etc or for shafts wells, cesspits, manholes, pier holes etc not exc 10sqm on plan and getting out in hard/dense soil complete all as specified and directed.
35Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with all kind of soil complete all as specified and directed.
36Removing excavated surplus soil n.exc 50m and depositing where directed at a level n.exc 1.50m above the starting point complete all as specified and directed by Engr-in-Charge.
37Taking down chowkats or frames with shutters (with out taking off shutters from the frames) exc 1.5 Sqm but n. exc 4 Sqm each complete all as specified and directed.
38Taking down chowkats or frames with shutters (with out taking off shutters from the frames) n. exc 1.50 Sqm each complete all as specified and directed.
39S&F 1.25 mm thick pressed steel frame of size 125 X 60 mm for door with one ore more rebate includings necessary fixing lugs, hinges, locks strike plate and PCC of door filling Double rebate etc complete all as specified and directed.
40S&F 1.25 mm thick pressed steel frame of size 105 X 60 mm for door with one ore more rebate includings necessary fixing lugs, hinges, locks strike plate inc PCC of door filling single rebate etc complete all as specified and directed.
41S&F factory made, 35mm thick 2nd class hard wood, plain framed, paneled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both sides, the side of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, 35 mm thick complete, all as specified and as directed.
42All as per Item No. 42.00 above, except that the panel shall be made of wire gauze in lieu of wood grain sheet panel. The wire gauze shall be securely wrapped around an additional 8 mm square M.S. solid tube, which shall be welded to the M.S. tubes. The wire gauze shall be properly stretched and tightened to ensure a firm, uniform and wrinkle-free finish, complete all as specified and directed.
43S&F factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube complete all as specified and directed.
44S&F factory made solid panel PVC door shutter wood grain in colour 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. M S frame shall be covered with heat moulded prelam PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and single side prelam PVC sheet for top rail, lock rail & bottom rail on either side and as gap insert for top rail & bottom rail; stile &rails having one side feathered edge and on other side 10mm 90^0 bent edge,Paneling of 2mm thick prelam PVC sheet on bothfaces i.e front face & back face with particle board core to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement,and including all hardware necessary for a door supplying & fixing in the frame at site as per specification & drawing.given SSR 2020 complete all as specified and as directed.
45S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed withn wooden beading or with nuts and bolts to existing steel windows/wooden windows complete all as specified and directed.
46S&F Aluminium Powder-Coated Sliding Ventilators in white colour, made of extruded aluminium profiles having wall thickness of 2.3 mm ± 0.2 mm. The Ventilator profiles shall have hollow sections with main chamber frame size of 88 mm × 52 mm and sliding sash size of 42 mm × 62 mm. Sliding mesh sash shall be of size 42 mm × 57 mm, with one vertical sliding interlock of size 45.50 mm × 28 mm in each shutter. Glazing beads of size 24.50 mm × 16 mm shall be mitre-cut and fusion-welded at all corners, including external aluminium safety grills for the ventilators, provision of holes for fixing hardware, water drainage arrangements, etc. The item shall include arrangements for fixing hardware, EPDM gasket of 1.2 mm ± 0.2 mm thickness and 30 mm profile galvanized steel frame to be inserted into the required profile. The frame shall be fixed to the wall using 8 mm × 100 mm long fasteners. Hardware shall comprise zinc-alloy touch locks with white powder-coated finish, steel roller system, stainless steel wire cloth having nominal wire diameter of 0.6 mm and average aperture width of 1.40 mm, along with all required accessories, complete in all respects as specified and directed by the Engineer-in-Charge.Note: The unit rate quoted by the contractor shall exclude the cost of glass but shall include the cost of all other connected accessories.
47S&F Aluminium Three-Track Sliding Windows, powder-coated in white colour, made of extruded aluminium profiles having wall thickness of 2.3 mm ± 0.2 mm. The window profiles shall have hollow sections with main chamber frame size of 88 mm × 52 mm and sliding sash size of 42 mm × 62 mm. Sliding mesh sash shall be of size 42 mm × 57 mm, with one vertical sliding interlock of size 45.50 mm × 28 mm in each shutter. Glazing beads of size 24.50 mm × 16 mm shall be mitre-cut and fusion-welded at all corners, including external aluminium safety grills for the windows, provision of holes for fixing hardware, water drainage arrangements, etc. The item shall include arrangements for fixing hardware, EPDM gasket of 1.2 mm ± 0.2 mm thickness and 30 mm profile galvanized steel frame to be inserted into the required profile. The frame shall be fixed to the wall using 8 mm × 100 mm long fasteners. Hardware shall comprise zinc-alloy touch locks with white powder-coated finish, steel roller system, stainless steel wire cloth having nominal wire diameter of 0.6 mm and average aperture width of 1.40 mm, along with all required accessories, complete in all respects as specified and directed by the Engineer-in-Charge.Note: The unit rate quoted by the contractor shall exclude the cost of glass but shall include the cost of all other connected accessories.
48S&F 5.5mm thick sheet glass n exc 0.50sqm in area to be fixed in alluminium windows complete all as specified and directed.
49S&F 300mm length, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.
50S&F 250 mm length, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.
51S&F 100 mm size of Butt hinges, medium weight cold rolled mild steel complete door etc complete all as specified and directed.
52S&F aluminium anodised barrel tower bolts of extruded section with 100 mm long bolt complete all as specified and directed.
53S&F aluminium anodised barrel tower bolts of extruded section with 200 mm long bolt complete all as specified and directed.
54S&F aluminium anodised barrel tower bolts of extruded section with 150 mm long bolt complete all as specified and directed.
55S&F Extruded aluminium alloy handles fabricated type anodised 150mm size complete all as directed and specified and as directed.
56S&F Extruded aluminium alloy handles fabricated type anodised 100mm size complete all as directed and specified and as directed.
57S&F floor door stopper of brass body and tongue, anodised, with hard drawn steel spring, 140mm long, fixed in floor complete all as specified and directed.
58S&F hasp and staple 125mm, safety type, aluminium anodised with alu hinge pin incl bolt to hinge plate and fixed with screws complete all as specified and directed.
59S&F 2nd Class hardwood Plain Fillets, square or triangular in section, clean sawn, properly dressed and secured in position with nails or brads, cross-sectional area exceeding 13 sq.cm but not exceeding 25 sq.cm complete all as specified and directed by the Engr-in-Charge.
60S&F 2nd Class hardwood Plain Fillets, square, rectangular or triangular in section, clean sawn, cross-sectional area exceeding 6 sq.cm but not exceeding 13 sq.cm, secured in position with nails or brads, wooden bearer of size 25 mm × 40 mm complete all as specified and directed by the Engr-in-Charge.
61S&F in repairs 18/19mm thick prelaminated particle board interior grade sprelaminated one side with decorative choice lamination and other side balancing white lamination fixed with nails to timber frame work complete all as specified and directed.
62S&F external teak wood lipping, 6 mm thick, properly dressed and fixed with nails along the edges of blockboard or veneered particle board of 18/19 mm thickness complete all as specified and directed.
63S&F continuous (piano) hinges,mild steel, bright finish or electro galvanised, Width of flaps (when open) in 30 mm etc complete all as specified and directed.
64S&F extruded aluminium alloy handles, fabricated type,anodised, Size of handle in 75 mm,etc complete all as specified and directed.
65S&F brass 2-levers locks for cupboard, grade I of size 50mm complete all as specified and directed.
66S&F100mm, stainless steel handles for cupboard fixed with nut, screw and washer of mild steel, bright finished and brass polished complete all as specified and directed.
67S&F fan light magnetic catch with 14mm catch cast brass and fixed to cupboard shutters all as specified and as directed
68S&F 18 mm thick factory made PVC sheet one side pre laminated sheet kitchen cabinet shutter/cupboard shutter. The 18mm thick sheet shutter bent at 90 degree and finish all edges at level for making edge lipping bending for 0.5 mm thick PVC sheet lipping at all four edges using bodning etc complete all as specified and directed by Engr-in-Charge.
69S&F factory made PVC shelf/partition of required size consisting of panel of 5 mm thick celuka PVC ply and for supporting the hold of shelf/partition and shall provide 3 edges in size 18mm x 18mm as per required length the front side of the edge visible in the fronth of the self / partition to be edge lipped by 18mm width x 1 mm thick PVC sheet of density 600kg/cum manufactured by ISO 9001-2015 Certified company using solvent cement etc complete all as specified and directed by Engr-in-Charge.
70S&F stainless steel shelf closing hinges 75 mm size for PVC door shutters complete all as specified and directed.
71S&F 50 x 15 mm size magnet door catcher for closing for PVC door shutter complete all as specifid and directed.
72S&F 100 mm size MS mat/glossy finish handle complete all as specfied and directed .
73S&F modular type stainless steel cutlery basket size 20 x 19 x 4 inches (dia of wire not less than 3.00 mm) of any shape withside sliding roller clip and silding rails on both side fixed with steel screws incl all fixing arrangements complete all as specified and directed.
74All as per item No 73.00 above but cup and saucer basket size 20 x 17 x 4 inches complete all as specified and directed.
75All as per item No 73.00 above but plain basket size 20 x 19 x 6 inches complete all as specified and directed.
76All as per item No 73.00 above but grain basket size 20 x 17 x 6 inches complete all as specified and directed.
77All as per item No 73.00 above but thali basket size 20 x 19 x 8 inches complete all as specified and directed.
78All as per item No 73.00 above but plain basket size 20 x 17 x 8 inches complete all as specified and directed.
79Form work to sides of concrete foundation including rafts, footings, foundation beams, bases of columns etc for fair finished surface complete all as specified and directed.
80Taking down 15mm bore steel tubing and connections in any position complete all as specified and directed.
81Taking down 20mm bore steel tubing and connections in any position complete all as specified and directed.
82Cutting chases, pinning in, making good to facings where required & pointing in cement mortar 1:3 for concealed water tubing, etc.& making good, cutting not exc 10 cm grith complete all as specified and directed.
83S&F 20mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including provision of special fittings ( Unions, elbow, Tee, Male threaded brass adaptor, Female threaded brass adaptor, Tank adaptor etc), complete all as specified and directed.
84S&F 25mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including provision of special fittings ( Unions, elbow, Tee, Male threaded brass adaptor, Female threaded brass adaptor, Tank adaptor etc), complete all as specified and directed.
85S&F 20 mm bore GI Tubing medium grade with all fittings fixed to wall/ ceiling or in floor complete as specified and directed.
86S&F in repairs 1000 ltrs capacity Rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including dismantling complete all as specified and as directed.
87S&F in repairs 20 mm dia brass ball valve, high pressure with polythene float and fly-nut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.
88S&F in repairs 20 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.
89S&F in repairs 15mm bore Bib taps, chromium plated cast copper alloy, fancy type, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.
90S&F in repairs 15 mm dia fancy type stop valves/ angle cock chromium plated screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.
91S&F long body CP Bib tap, cast copper alloy with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.
92S&F angular stop valves, cast copper alloy, screwed down, high pre-ssure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.
93S&F Bib taps, cast copper alloy with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.
94S&F Brass CP Tubular towel rail, 20mm dia, D type, 60cm long between flanges fixed complete all as specified and as directed.
95S&F chromium plated shower roses 125mm sizes with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed.
96S&F Health faucet (ABS Bpdy) mild steel chromium plated suitable for 15mm dia pipe 1.25 M long flexible tube and ABS wall Hook including making connection and fixed in position with two way tap complete all as specified and as directed.
97S&F in repairs stainless steel Kitchen sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm including necessary PVC outlet pipe and coupling complete all as specified and directed.
98S&F in repairs stainless steel plate rack 31\\" X 36\\" X 10\\" made up of 1mm thick sheet (Non magnetic) complete all as specified and directed.
99S&F in repairs vitreous china wash down water closet pedestal pattern white excluding flushing cistern and flush pipes complete all as specified and as directed .
100S&F in repairs vitreous china wash basin, white, flat back size 550 x 400mm including 01 Nos cast copper alloy 15mm CP fancy type pillar tap, 01 Nos 32mm waste coupling , one pair of MS bracket, cutting for and pinning in ends of brackets complete all as specified and directed.
101S&F in repairs PVC valveless syphonic action type flushing cistern 10 lit capacity low level white with inlet, ball valve, float and handle including brackets and 32mm PVC flush pipe complete all as specified and directed.
102S&F in repairs PVC connection 15mm dia, 45 Cms long with brass ferrules on both ends fixed complete all as specified and directed.
103S&F in repairs PTMT Shelf of weight not less than 300 gms with soap dish (tray) fixed with and including Chromium plated brass screws and wooden / plastic cleats etc., complete all as specified and as directed.
104S&F in repairs 600mmx450mm belvelled edge looking mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood with PVC / alluminium frame and fixed to wooden plugs with chromum plated brass screws, cup washers, complete all specified and directed.
105S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.
106S&F in repair 550mmx350mm PVC Cabinet Mirror with shelves of selected quality glass and fixed on walls to wooden plugs with chromium plated brass screws, cup washers complete all specified and directed.
107S&F in repairs PVC( SWR ) pipes 110mm dia single socketed , in any length with rubber ring joints as rainwater, soil waste and vent pipe (with all fittings) fixed to wall or laid in trenches incl taking down existing pipe complete all as specified and directed.
108S&F in repairs PVC( SWR ) pipes 75mm dia single socketed , in any length with rubber ring joints as rainwater, soil waste and vent pipe (with all fittings) fixed to wall or laid in trenches incl taking down complete all as specified and directed.
109S&F in repairs PVC (SWR) bends any radius 110mm bore complete all specified and directed.
110S&F in repairs PVC (SWR) bends with access door any radius 110mm bore complete all specified and directed.
111S&F PVC (SWR) junction single (single T) equal or unequal with access door of bore 110mm complete all specified and directed.
112S&F PVC(SWR) vent cowl 110mm bore complete all specified and directed.
113S&F PVC (SWR) bends any radious 75 mm dia complete all specified and directed.
114S&F PVC (SWR) bends with access door any radious 75 mm dia complete all specified and directed.
115S&F PVC (SWR) junction single (single T) equal or unequal of bore 75mm complete all specified and directed.
116S&F in repairs PVC (SWR) Floor trap/Nahani trap plain or multi with stainless steel grating incl joinig to waste pipe with solvent cement joint dia of outlet 75 mm bore complete all as specified and directed.
117S&F PVC (SWR) junction single (single T) equal or unequal with access door of bore 75mm complete all specified and directed.
118S&F in repairs PVC (SWR) floor trap 75mm dia outlet, plain with grating including jointing with solvent cement complete all specified and directed.
119S&F PVC waste pipe for urinal/WHB with fitting etc 38 mm dia. 60mm long complete all specified and directed.
120S&F framed work as in grills, gratings, doors or gates of angle or other section with gusset plates, rails, braces, etc. complete, drilled for fixing of steel sheeting or other covering doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, Fe 410-W (Gde-E-250) quality-A, etc complete all as specified and directed.
121M&L for preparation of newly untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.
122M&L for preparation of old painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all specified and directed.
123M&L for preparation of old painted wooden surfaces of any description over 10 cms width or girth not otherwise described and applying one coat of synthetic enamel paint complete all specified and directed.
124M&L for complete removal of existing treatment and preparation of old surfaces and applying two coat Acrylic emulsion disptember over applying minimum 1mm thick white wall care putty and primer over prepared surface to achieve the surface even and smooth for painting complete all as specified and directed.Notes: (i) The contractor shall furnish a guarantee for a period of four (4) years against the quality of materials and workmanship and any defects in the work executed.(ii) Application of primer and emulsion paint shall be carried out mechanically using an airless spray machine.
125M&L for preparation of new ceiling surfaces and applying three coat of white wash, complete all as specified and directed.
126M&L for preparation of newly plastered surfaces and applying two coat Acrylic emulsion distember over applying minimum 1mm thick white wall care putty and primer on prepared surface to achieve the surface even and smooth for painting complete all as specified and directed.Notes: (i) The contractor shall furnish a guarantee for a period of four (4) years against the quality of materials and workmanship and any defects in the work executed.(ii) Application of primer and emulsion paint shall be carried out mechanically using an airless spray machine.
127M&L for complete removal of existing treament and preparation of wall, washing, scrubbing down and stopping old treatment and painted surface of plastered / decorated surface and applying two coat of Premium Acrylic smooth exterior paint and including priming coat of exterior primer and one coat of wall putty complete all a specified and as directed.(Note : painting will be done by brush / spray / roller of building upto the height) all as per directed by Engr -in-Charge. Note:- (i) The contractor shall furnish a guarantee for a period of four (4) years against the quality of materials and workmanship and any defects in the work executed.(ii) Painting shall be carried out by brush, spray or roller, as suitable for the building height and site conditions, as directed by the Engineer-in-Charge.(iii) The rate shall include all necessary scaffolding, safety arrangements and protective measures wherever required at site, complete in all respects.
128M&L for preparation of newly plastered / decorated surface and applying two coat of Premium Acrylic smooth exterior paint and including priming coat of exterior primer and one coat of wall putty complete all a specified and as directed.(Note : painting will be done by brush / spray / roller of building upto the height all as per directed by Engr -in-Charge). Note:- (i) The contractor shall furnish a guarantee for a period of four (4) years against the quality of materials and workmanship and any defects in the work executed.(ii) Painting shall be carried out by brush, spray or roller, as suitable for the building height and site conditions, as directed by the Engineer-in-Charge.(iii) The rate shall include all necessary scaffolding, safety arrangements and protective measures wherever required at site, complete in all respects.
129Complete removal of existing tretment on ceiling surfaces including washing rubbing down and stopping of distempered and painted surfaces complete all as specified and directed.
130Excavation post holes (or similar holes) each n exc. 0.50 Cum, getting out Hard/ dense soil, Returning, filling in and ramming earth or broken rubble mixed with earth around, in layersn.exc. 25 cm, watering and removing surplus soil to a distance not exc 50m and making good surface complete all as specified and directed.
131M&L for plain cement concrete type C-2 1:3:6 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.
132S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and as directed.
133S&F 0.50mm thick (including coated thickness) pre-colour pre- profiled (Galvalume/zinkalume) sheets of required colour and design having tensile strength of 550 Mpa as in roof sheeting/sunshade/ wall cladding, north light curves, fixed with zinc coated self drilling fastener including EPDM washer complete laid with one corrugation side laps and min 150mm end lap laid to slope all as per manufacturer / profile maker instruction complete all as specified and as directed.
134S&F 0.50mm thick (including coated thickness) pre-painted pre- profiled (Galvalume/zinkalume) sheets of required colour and design having tensile strength of 550 Mpa Plain steel sheet as in roof sheeting/sunshade/ wall cladding, north light curves, fixed with zinc coated self drilling fastener including EPDM washer complete laid with one corrugation side laps and min 150mm end lap laid to slope all as per manufacturer / profile maker instruction complete all as specified and as directed.
135Taking down copper /aluminium point wiring (light, fan, bell,socket or power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets, etc. Removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces of walls, floors etc.complete all as specified and directed.
136Taking down ceiling fan/ exhaust fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan blades and deposit to MES store yard of AGE E/M complete all as specified and as directed.
137Taking down existing geyser of any capacity after disconnecting all necessary electrical and water supply connections and deposit to MES store yard of AGE E/M complete all as specified and as directed.
138M&L for point wiring with 1.5 Sq mm single core PVC insulated unsheathed copper FRLSH multi stranded conductor cable in and including concealed PVC conduit of size 20/25mm ISI marked inclusive of tees ,bend ,elbows etc upto and including modular sunken anodised steel box for housing modular switch socket , regulator etc including modular cover plate and cover frame of any module ISI marked of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sq mm FRLSH cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed by Engr-in-Charge for the following:-(a) One light point/bell/fan point controlled by one switch
139(b) One light point/fan controlled by Two switch
140(c) One 5amps socket out let point controlled by one switch on same board with other switches.
141(d) One 5amps socket out let point on independent board controlled by one switch.
142All as per item No 138.00 above but using 2.5 sq mm single core copper conductor cable of multistranded FRLSH PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point on independent board including necessary running of 2.5 sq mm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.
143M&L for point wiring with 1.5 Sq mm single core PVC insulated unsheathed copper FRLSH multi stranded conductor cable in in existing conduit & making good the disturbed surface of wall with and including modular sunken anodised steel box for housing modular switch socket , regulator etc including modular cover plate and cover frame of any module ISI marked of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sq mm FRLSH cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed by Engr-in-Charge for the following:-(a) One light point/fan/ Bell point controlled by one switch
144(b) One 5amps socket out let point controlled by one switch on same board with other switches.
145(c) One 5amps socket out let point on independent board controlled by one switch.
146All as per item No 140.00 above but using 2.5 sq mm single core copper conductor cable of multistranded FRLSH PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point on independent board including necessary running of 2.5 sq mm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.
147S&F Modular Switch , single pole, one way, and 5/6 Amp single module complete all as specified and directed.
148S&F Modular Switch , single pole, two way, and 5/6 Amp single module complete all as specified and directed.
149S&F Modular Switch , single pole, one way, and 15/16 Amp single module complete all as specified and directed.
150S&F Modular Socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module complete all as specified and directed.
151S&F Modular Socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module complete all as specified and directed.
152S&F Bell push modular 6 Amps single module complete all as specified and directed.
153S&F lamp holder , PVC / Polycarbonate type with back plate suitabl for batten/ slanting fittings complete all as specified and directed.
154S&F modular step type fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and directed.
155S&F ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting complete all as specified and directed.
156S&F bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified and as directed.
157S&F brushless direct current motor (BLDC) ceiling fans complete with blades(03Nos), with remote control and accessories , 230 V, 50 Hz, 1200 mm sweep, Min air delivery 210 CMM with service value greater than 7.75 BEE. Five star rated, provide electrical connection from ceiling rose to fan terminal by providing flexible cable three core Copper conductor of size 23/0.0076 (3 Core x 0.50 Sqmm), ISI marked and write down MES Number on fan by black paint/Marker complete all as specified and directed by Engr-in-Charge. Make :- Havells Model No. Efficiencia Neo BLDC FHCNF5SWHT48 or Crompton Model No.Groove Regmote /Bajaj//Orient / make as per Particular Specification (list of Make) as approved by GE.
158S&F exhaust fan , steel/metal body AC single phase, 230 V of size 300 mm sweep with blades, frame and louvers complete all as specified and as directed.Make :- Havells /Crompton /Bajaj//Orient / make as per Particular Specification (list of Make) as approved by GE.
159S&F exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base compelte all as specified and directed. Make :- Havells /Crompton /Bajaj//Orient / make as per Particular Specification (list of Make) as approved by GE.Note : Cost of suitable opening wall for fixing exhaust fan is deemed to be included in overall rate quoted.
160S&F in repairs Highly efficient LED Inverter Bulbs, 09 W, used as a ready replacement for existing GLS/CFL direct fit lamp in B-22 cap of Make: Bajaj/ Havells/ Philips/ Crompton / make as per Particular Specification (list of Make) as approved by GE.
161S&F in repairs Wall light fittings suitable for LED bulb including LED bulb of 7 watt, including connection with all necessary fixing accessories complete all as specified and directed by Engr-in-Charge. Make :- Havells Cat No. LHFOAJE1TN1I060 /Bajaj/ Philips/ Crompton / Wipro / make as per Particular Specification (list of Make) as approved by GE.
162S&F in repairs integrated LED tube light fitting 1x18/20 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square boxes including taking down the existing complete all as specified and directed. Make:-Havells Cat No. LHEXAPP7PN1W020 /Bajaj/ Philips/ Crompton / Wipro / make as per Particular Specification (list of Make) as approved by GE.
163S&F in repairs decorative ultra slim LED light fitting 2 feet 10 watts, 6500K batten aluminium extruded with end caps complete all as specified and as directed. Make:- Cat No HEXBLP7IN1W009 of Havells /Bajaj/ Philips/ Crompton / Wipro / make as per Particular Specification (list of Make) as approved by GE.
164S&F energy saving new generation 10 watts LED bulk head fitting IP 65 luminaire with opel diffuser pre wired with warranty option of 5 years from date of installation and necessary mounting arrangements , provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb complete all as specified and as directed. Make:- Havells Cat pt No. HEXAFT10WLED857SSYMBOPC /Bajaj/ Philips/ Crompton / Wipro / make as per Particular Specification (list of Make) as approved by GE.
165S&F energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 30 watts with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe 40 mm dia medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engr- in-charge. Make:- Cat No LHETAVU7PA7J030 of Havells/Bajaj/ Philips/ Crompton / Wipro / make as per Particular Specification (list of Make) as approved by GE.
166Supply assembly, erection, testing commissioning of indoor wall mounted panel frame size of 1500mm X 900mm X 247mm mounted cubical type factory made IP 65 of environment friendly polycarbonate PC - GFS Insulation-enclosed power distribution board as power switchgear and control gear assembly (PSC) in accordance with IEC 61439-2wall mounted LT panel board with OEM Manufacturing certificate,Bottom parts and lids of the boxes made from impact-resistant polycarbonate, halogen and silicone-free, colour RAL 7035, transparent lid with quick action fasteners for tool operation. Burning behaviour according to IEC 60695-2-11 glow wire test + 960°C.Maximum water absorption 10 mg in accordance with DIN 53473. Protective measure: totally insulated (protection class II), the enclosure should have mechanical strength equivalent to IK10 (bidder should submit compliance for same for polycarbonate enclosure in OEM letterhead with technical bidding) suitable for 415V 3 phase 4 wire, 50HZ non metalic kiosk single door with the required provision for 3 switch gears and control gears along with the approved make. the LT panel including Sepratedcomparment for fixing of fourNosThree Phase &single phase meter and providing MCB,providing glass view for reading of meter complete fabrication shall be painted as per specification. Wall mounted LT panel board shall be complete with all standard accessories factory made with OEM manufacturing certificate & the type tests report as per CPRI ,including, phase indicating lamps control fuse unit, MV danger notice plate numbered/lettered and with comprising the following. Drawing from Original Equipment Manufacturing ( OEM )to be got approved from accepting officer before supply of Panel. ( Drawing from any other agency / System house will not be accepted. Panel should be manufactured and assembled by OEM only. Fabrication /Assembling from any other system house will not be accepted. The bidder should submit all relevant type test certificate / compliance in OEM letterhead during technical evaluation. The bidder should provide warranty / guarantee format in OEM letterhead. The bidder should submit Routine test certificate during order execution in OEM letterhead.Make: HENSEL Mi Power distribution board / SpelsbergGTi System/ Rittal polycarbonate enclosure*Incoming : MCCB 125A, 4 pole, 25KA-1 No.,RYB Indication lamp, Digital Ampere Meter . Digital Volt Meter ,125A/5A,5VA,CL.1, CT – 3 Nos,Fuse Terminal Block with 2A Fuse-6 NosOutgoing : connecting the following switch gear: (i) MCB, 40A FP amps, 415 volts, ‘C’ curve, 10 KA - 04 Nos (ii) MCB, 32A DP amps, 240 volts, ‘C’ curve, 10 KA - 04 Nos (iii) Fixing only 3phase &1phase serviceable existing electric meter- 08 Nos each
167S&F in repairs metal clad box suitable for 230 volt 50 Hz for AC and Geyser connection three pin and socket with MCB SP 20/32 Amps including removal of old unserviceable one complete all as specified and as directed complete all as specified and as directed.
168S&F in repairs sheet metal enclosure MCB DB SPN 12 way, IP-43, IK 09 with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.
169M&L for Sub main wiring (in replacement) with two runs of single core FR LS PVC insulated unsheathed cable 1100 volts grade, 6 Sqmm size with multistranded copper conductor, drawn in and including non metallic rigid PVC conduit of not less than 25 mm dia concealed in wall by cutting chases of wall and making good the disturbed surface, including PVC insulated unsheathed FR LS 6.0 Sqmm cable with multistranded copper conductor green PVC insulated as contineous earth conductor cable connected to earth dolly from main distribution board complete all as specified and directed by Engr-in-Charge. Make of PVC conduit/Casing Caping:- Plaza/Finolex/Polycab/Kalinga/Jindal/Asian.Note:- Two runs of 6 sqmm cable, one run of 6 sqmm cable and one run of PVC conduit will be measured as one unit.
170M&L for Sub main wiring (in replacement) with two runs of single core FR LS PVC insulated unsheathed cable 1100 volts grade, 4 Sqmm size with multistranded copper conductor, drawn in and including non metallic rigid PVC conduit of not less than 25 mm dia concealed in wall by cutting chases of wall and making good the disturbed surface, including PVC insulated unsheathed FR LS 4.0 Sqmm cable with multistranded copper conductor green PVC insulated as contineous earth conductor cable connected to earth dolly from main distribution board complete all as specified and directed by Engr-in-Charge. Make of PVC conduit/Casing Caping:- Plaza/Finolex/Polycab/Kalinga/Jindal/Asian.Note:- Two runs of 4 sqmm cable, one run of 4 sqmm cable and one run of PVC conduit will be measured as one unit.
171S&F in repairs MCB, SPN rated capacity 40 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.
172S&F in repairs MCB, SP rated capacity 6 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.
173M&L for Earthing complete (in replacement) with galvanized steel earth plate electrode 60cm x 60cmx 6 mm thick buried directly in ground ( earth pit not less than 2.25 meter deep below ground level) with the top edge of the earth plate not less than 1.5 meter below normal ground level connected to galvanized earth lead wire 4mm dia by means of bolts, nuts, check nuts and washer of galvanized iron or of steel all as shown in electrical plate No.5 of MES SSR Parts-I and including excavation & earth work in any type of soil , disposal of soil , providing alternate layers of charcoal and common salt, construction of PCC earth chamber in mix (1:3:6) type C-1 with 40 mm thick RCC (1:2:4) type B-1 cover reinforced with 8mm dia MS TMT bars both ways with lift hook made out of 8 mm dia bar, watering arrangement with funnel and wiremesh and watering pipe of 20mm dia GI light grade and 15mm dia light grade pipe for earth lead protection and testing on completion complete all as specified and directed.Note : GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.50 m from earth plate is deemed to be included in rate quoted. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58462864
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE 48.49 Lakhs
LAST DATE 01-12-2026
Authority
Authority Name Military Engineer Services
Work Description Tender For Special Repair To Cb-199 Jcos/Or Md Accn Under Ge (Mis) Mhow
Basic Detail
Tender No 8988/GE (MIS)/Mhow
Bidding Type Tender
Location
City Indore
State Madhya Pradesh
Key Dates
Publish Date 10 Nov 2026
Submission Date 01 Dec 2026
Open Date 03 Dec 2026
Finance
Tender Value 48.49 Lakhs
Tender Fee 500
EMD 97000
Exemption Available
Document List
2add9405-56ac-40e5-95a3-303b56730e94.html
BOQ_895284.xls
DetailsOfWorkInAndInHand.pdf
ListOfMakeMake8988.pdf
ParticlularSpecifications8988.pdf
Tenderandspecialcondition8988.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 10, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 01, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 14 days
Dec 03, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 16 days

Tender Documents

Download All (ZIP) ↓
html

2add9405-56ac-40e5-95a3-303b56730e94.html

xls

BOQ_895284.xls

pdf

DetailsOfWorkInAndInHand.pdf

pdf

ListOfMakeMake8988.pdf

pdf

ParticlularSpecifications8988.pdf

pdf

Tenderandspecialcondition8988.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender