Defence Statutory Bodies & Commissions/Committees Closing in 15 days TDR #58462695

Tender For Addition/ Alteration To Building No P-487, P-488 & P-493 Of 22 Weu Leh Under Ge 865 Ews.

Issued by Statutory Bodies & Commissions/Committees · leh, Ladakh
Tender Value
43.46 Lakhs
Estimated cost
Bid Submission
02 Dec 2026
15 days left
EMD
87000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
leh → Ladakh
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender For Addition/ Alteration To Building No P-487, P-488 & P-493 Of 22 Weu Leh Under Ge 865 Ews.

BOQ

Name of Work:- ADDITION/ ALTERATION TO BUILDING NO P-487, P-488 & P-493 OF 22 WEU LEH UNDER GE 865 EWS.
Sl. No. Item Description
1Dismantling floor, hearth or wall tiling including wall cement mortar, bedding (But not backing ) and rubbish of premises, complete all as specified and as directed.
2M&L for 25 mm thick PCC 1:2:4 type B1 using 20mm graded stone aggregate as in sub base of floor, complete all as specified and as directed.
3M&L Non-Skid ceramic Coloured Tiles 7 to 8mm thick(squre/rectanglar) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors over 15 mm screed bed or bedding layers in cement mortar 1:4 Set and Jointed in neat Cement Slurry and Pointed in Colour Cement to match, complete all as specified and as directed.
4M&L Light shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles including 15 mm thick screed in cement mortar (1:4) as in floors etc, complete all as specified and as directed.
5S&F Coloured Glazed colour ceramic tiles in vertical surfaces 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick plaster in CM(1:4) joint free with grout of matching shade, complete all as specified and as directed.
6Taking down cement plaster on brick or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc., complete all as specified and as directed.
7M&L for 10mm thick rendering on other than fair faces of Stone wall works finished even and smooth without using extra cement in cement mortar 1:6 complete all as specified and as directed
8M&L for 10mm thick rendering on other than fair faces of Stone wall works finished even and smooth without using extra cement in cement mortar 1:4 complete all as specified and as directed.
9M&L Rendering 5 mm thick on fair faces of brick work or concrete surfaces, finished even and smooth on ceiling in cement mortar (1:4), complete all as specified.
10Supply only integral liquid water proofing compound complete all as specified and directed.
11M&L for 1mm thick wall care putty complete all as specified and directed.
12Material & Labour for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces using roller for painting complete all as specified and directed .
13M&L for preparation of newly plastered surfaces of wall by applying wall care putty averaging thickness 1mm and rubbing with sand paper for making smooth surface and applying two coat of oil emulsion distemper over one coat of primer through roller, complete all as specified and directed .
14M&L For preparation of old surface after complete removal of existing treatment by mechanical complete all as specified and directed
15M&L for 1 coat of prime using roller complete all as specified and directed.
16M&L for Two coat of OBD using roller for painting complete all as specified and directed
17M&L preparation of Complete removal of existing treatment plastered old surface of of wall by applying 1mm thick wall care putty and making the surface smooth Finishing walls and applying Acrylic Smooth exterior paint of required shade (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)using roller for painting complete all as specified and directed.
18Dismantling wall and ceiling boards (Fiber, pulp, insulation, blankets) any thickness including covered fillets and supporting members, complete all as specified and as directed.
19M&L for 9mm thick prelaminated particle board medium interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with nails to timber frame work as in wall panelling, shelves/boarding complete all as specified and as directed.
20M&L Anodised aluminium snap grid frame work for false ceiling Hangers 6 mm dia. G.I. (upto1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I.flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specifiedall as specified
21Material and Labour 6 mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/ GI/Aluminium framework with screws, complete all as specified and as directed.
22M&L Prelaminated particle board,18/19 mm thcik both side interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, complete all as specified and as directed.
23M&L for 9mm thick prelaminated particle board medium interior grade, prelaminated one side with decorated choice lamination & other side balancing white lamination fixed with nails to timber frame work as in ceiling panelling, shelves/boarding complete all as specified and as directed.
24S&F Piano/continuous hinge of size 40 mm (when open) stainless steel, complete all as specified and as directed.
25Dismantlng framed wooden fillets, rails, posts, rafters, purlins, grids for ceiling & wall panelling etc under 40 Sq.cm in secton unframed work, complete all as specified and as directed.
26M&L for 2nd class soft wood clean sawn as in battens for grids of ceiling & lining fixed with nails exc 13 sqcm and n exc 25 sqcm in section.complete all as specified and as directed.
27M&L for 2nd class soft wood clean sawn as in beeding for edges of Ceiling ,lining ,or wooden flooring work fixed with nails exc 6 sqcm and n exc 13 sqcm in section.complete all as specified and as directed.
28M&L for covered fillets of standard hard board not less than 6mm thick and up to 40mm wide and fixing with screws complete all as specified and as directed.
29Demolition of precast concrete block walling built in cement mortar including all quoins, arches , pillars etc, complete all as specified and as directed.
30M&L for pre cast solid block masonry set in CM 1:6 & casted in cement concrete type C-1 (1:3:6) using 20mm graded curshed stone aggregate complete all as specified and directed.
31All as per item No. 30 here-in-before but except blocks.
32Demolition of cement concrete in ground floor and pavings n'exc 15cm thick below or above ground level complete all as specified and as directed.
33M&L for Cement concrete type D-2,1:4:8 (40mm graded aggregates) 75 mm thick as in sub -floors ,sub- bases ,floors and pavings,etc.
34M&L for Chequred cement concrete tiles (glazed) 30cm X 30cm X 20mm thick, set ,pointed & jointed in neat cement slurry in floors polished with grey cement & pigments and layed over 20mm thick cement screed base (1:6), complete all as specified and as directed.
35M&L machine pressed precast concrete interlocking paver block any shape and size polished with grey cement and pigment confirming to IS 15658-2006 of 60 mm thickiness M-35 grade complete all as specified and as directed by Engr-in-Charge.
36M&L sand filling (50 mm average thickness) under floors in foundations and for laying Interlocking paver blocks including watering and consolidation complete all as specified and as directed by Engr-in-Charge..
37M & L for 75 mm PCC 1:2:4 type B-1 using 20mm graded aggregate as plinth protection finished even and smooth with out using extra cement
38M&L Forming Contraction (Dummy) joints 65 mm deep x 10mm wide, filled with sealing compound Grade 'A' in plinth protection
39M & L Pre-cast Type C1 1:3:6 20mm graded aggregate cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in mortar, complete all as specified and directed
40Taking down chowkats / frames with shutters (without taking off shutters from the frames) area n'exc 1.5 Sqm each complete all as directed by Engr-in-charge.
41Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exceeding 1.5 Sqm and not exceeding 4 Sqm each complete all as directed by Engr-in-charge.
42Pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixings lugs,excluding hinges,lock strike plate,etc,complete ,as specified ,supplied and fixed.
43S&F anodised aluminium frames for door, windows, ventilators with one or more rebates including joining cleat for fixinf etc complete all as specified.
44S&F Anodised aluminium door shutters, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading screws etc. complete all as specified
45S&F Anodised aluminium window and ventilator shutters,including aluminium jali fixed in one side, side hung type without sash,aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium fittings such as peg stays 150mm long (1 Nos) hinges type B-21 100mm long (2 Nos) suitable handle (1 Nos) etc including powder coated anodised aluminium frame, grill with one or more rebates. complete all as specified
46M&L sheet glass 4.8mm thick ordinalry quality and glazing with oil putty or wooden beads in square not exc 0.50 sqm in each pane complete all as specified and as directed.
47S&F 2nd class soft wood 35 mm thick Glazed and skelton shutter, open and prepared to receive the glass, gauze etc.(without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc. (Glass / Wiremesh should be measured seperately) complete all as specified and as directed by the Engr-in-Charge..
48S&F for 40 mm thick Flush shutters, solid core construction ,with block board core and plywood face panels commercial type on both sides , Supply and fixed to chowkats , complete all as directed by Engr-in-charge.
49S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, as per specification.
50S&F Factory made solid panel pvc door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined to-gether with solvent cement as per specification.
51M & L for preparing new wood & wood based surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.
52S&F in repairs Galvanised mild steel wire cloth ,0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples.
53S&F 150mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and as directed.
54S&F 100mm long aluminium anodized, barrel tower bolt of extruded section, complete all as specified and as directed.
55S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed.
56S&F 100 mm size extruded aluminium alloy handles, fabricated type, anodized, complete all as specified and as directed.
57S&F in repair aluminium (Die cast) body door closer hydraulically dessignation No 3 universal type suitable for door shutter of 851 to1000mm in width and weight 61 to 80 kg all as specified and directed
58S&F floor door stopper (Length of cover plate) 150mm long aluminium alloy body and tongue anodised with hard drawn steel spring fixed in floor, complete all as specified and as directed.
59S&F 100mm long aluminium anodized, butt hinges of extruded section complete all as specified and as directed.
60S&F100mm long mild steel butt hinges, medium weight cold rolled 100mm size complete all as specified and as directed.
61S&F in repair 250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed complete all as specified and as directed
62S&F, Mortice lock, brass, four lever, verticle type, size 75mm complete all as specified and directed.
63Demolition of stone slabs and tiles of any description or thickness in floors aprons etc.laid bedded and pointed in any mortar, complete all as specified and as directed.
64M&L for 20 mm thick granite stone (any type) (table rubbed and polished) in steps, jambs, pillars, window cills, cooking plateform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite including cutting, etc and screed bed with CM (1:4) 20mm thick laying floor tiles complete all as specified and as directed.
65Dismantling water tank exc 500 & n exc 1000 litre and removing to store, complete all as specified and as directed.
66S & F rotational moulded HDPE water storage tanks 1000 ltrs capacity and will be PUF insulated with 75mm thick PUF insulation of density 48 kg/Cum inner and out white two layers ISI marked ( cylindical vertical type/rectangular loft type closed top) hoisted hoisted with threaded cap and fixed in position all as specified in SSR Part I including all accessories (ie GI nipple etc), including provn of 20/25 mm dia spout for connecting inlet, outlet, over flow and washout pipes and including dismantling water tanks and removing to store of 1000 ltrs capacity complete all as specified and as directed by Engr-in-Charge.
67S&F 25mm bore stop cock chromium plated screw down under high pressure with crutch or butter fly handle screwed both ends for iron pipe or brass ferrule, complete all as specified and as directed.
68S&F 25mm ball brass valves, high pressure with polythene float and fly nut complete screwed for iron/PPR pipe and fixed in repair, complete all as specified and as directed.
69S & F in repairs fancy type 15mm bore chromium plated bib taps, cast copper alloy, with crutch or butterfy handle, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and as directed.
70Taking up or down 15 mm bore steel tubing and connections and set aside for re-use or removal to store, complete all as specified and as directed.
71Taking up or down 25/32 mm bore steel tubing and connections and set aside for re-use or removal to store, complete all as specified and as directed.
72S & F 25mm dia 3 layer PP-R polypropyene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete all as per manufacture instructions, complete all as specified and as directed.
73S & F 32mm dia 3 layer PP-R polypropyene random copolymer concealed pipes SDR 7.4 (PN 16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete all as per manufacture instructions, complete all as specified and as directed.
74S&F, in repair, vitreous china wash down water closet pan (Pedestal pattern), white with 'p' or 's' trap (excluding flushing cistern and flush pipe), including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc. complete all as specified and directed.
75S&F15 dia Angle stop valves, fancy type chromium plated with lonk shank and cup cast copper alloy , screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipes, complete all as specified and as directed.
76S&F PVC connectons 15 size with PTMT nuts (length 600mm), complete all as specified and as directed.
77S&F in repair 600x450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial ply wood and fixed to wooden plugs with cromium plated brass screws and cup washers, complete all as specified and as directed.
78S & F in repair Vitreous China wash basin Fency type pedestal pattern , white, flat back, size 550 x 400mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe, complete all as specified and as directed.
79S&F in repairs health faucet (ABS Body) mild steel shromium plated suitable for 15 mm dia with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, complete all as specified and as directed.
80Supply & Fixing sheet glass shelf assembly consisting of 8mm thick glass shelf 300 x 300mm as in corners wide with bevelled edges/hatching of edges fixed with stainless steel 'D' bracket fixed and railing complete all as specified and directed.
81Supply & Fixing sheet glass basin shelf assembly consisting of 8mm thick glass shelf 600 x 150mm wide with bevelled edges/hatching of edges fixed with stainless steel 'D' bracket fixed and railing complete all as specified and directed.
82S&F in repair 15mm bore CP wash basin mixer for mixing hot & Cold water copper alloy fancy type high pressure screwed for iron pipe and fixed in repair, complete all as specified and as directed.
83S & F in repairs 750 mm long, 32/ 40 mm dia., PVC flexible Waste pipe for sinks / wash hand basins, complete all as specified and as directed.
84S & F in sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, Waste pipe including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, complete all as specified and as directed.
85S & F in repairs, 40mm waste coupling of PTMT for sink and wash hand basin (Half or full threaded ) (Minimum Weight 45 grams), complete all as specified and as directed.
86S & F in repairs, 32mm waste coupling of PTMT for sink and wash hand basin (Half or full threaded ) (Minimum Weight 45 grams), complete all as specified and as directed.
87Dismantling wrought iron or mild steel work of any description not otherwise provided for angle iron or flat iron as in post and guard bars or grating, complete all as specified and as directed.
88S&F MS Rolled sections in main and cross beams,hip and jack rafters ;purlins where connected to common rafters running rails and guids for sliding doors ;fixed with angle cleats or other connecting plates and similar work confirming to Fe-290, Gde-E-165 complete all as specified and as directed.
89S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240, complete all as specified and as directed.
90M&L preparation of new untreated steel surfaces exc. 10 cm width/girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.
91Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) and rubbish off the premises, complete all as specified and directed.
92M&L for Reinforcement cement concrete (Nominal Mix) in type B1 1:2;4 ( 20mm graded aggregate) as in slabs supported of walls , beams and columns in floors, roofs, landings, balconices , canopies , deck slabs and in shelves etc, complete all as specified and as directed.
93M &L for form work to soffits of suspended slabs flat type such as roof slabs , floor slabs , landings and similar work nto exceeding 200mm thick (Horizontal or slopping etc complete all as specified and as directed
94M&L mild steel TMT bars 10mm dia and over, cut length, bent to shape required , including cranking , bending spirally for hooping for coloumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to TMT bar.
95Excavation over areas not exc 1.5 m deep for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc plan area exc 10 sqm hard/dense soil and getting out soil, complete all as specified and as directed.
96Returning filling in (soil) including spreading, levelling, watering and well ramming in layers n.exc 25cm thick in any type of soil complete all as specified and directed.
97Removal of excavated material (soil) to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.
98S&F 150mm dia bore (inner dia) double wall corrugated HDPE pipe (SN 8) in any length including all fittings and jointing with eastomeric rubber link and cuppler/other jointing materials laid in trenches or in floor including Concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) for 150 mm bore pipes and dismantling of cast iron/ PVC or reinforced concrete pipes jointed in cement mortar and taking out of trenches if reqd of any dia complete all as specified and directed.
99S&F in repair 19mm dia mild steel, chromium plated curtain rods fancy type , with brackets, end bulbs, complete all as specified and as directed.
100S&F in repairs Soap dish Cromum plated fancy type, complete all as specified and as directed.
101S&F in repairsTowel rail 600mm long Cromum plated (Minimum weight 190 gms), complete all as specified and as directed.
102S&F in repairs Towel Hanger with 6 Nos of pin and 600mm long Chromium plated etc, complete all as specified and as directed.
103S&F in repairs, 10 litres capacity PVC valveless syphonic action type, flushing cistern (ISI marked), low level ,white ,with inlet, ball valve, float and handle including bracket & flush pipe of polyethylene of low or high density or high density or PVC,32mm dia,for low level cistern complete all as specified & directed.
104Dismantling of cast iron, PVC or reinforced concrete drain pipes, 75/110/150/200 mm dia, jointed in cement mortar and taking out of trenches, if required, Complete all as specified and directed.
105110 mm bore PVC (SWR) single socleted in any length with rubber rings joints, fixed to walls and vent pipe as specified and directed.
106S & F in repairs 110 mm bore PVC (SWR) bends of any radius complete all as specified and directed.
107S & F in repairs 75 mm bore PVC (SWR) bends of any radius complete all as specified and directed.
108M&L PVC (SWR) 75 mm dia floor trap with plain with grating including jointing with solvent cement complete all as specified and directed.
109S&F grating doom 75mm dia of CP (min weight 25gms) complete as specified and directed
110Roughenng surface of old concrete floor by picking ,sweeping clean and washing down with water to remove dust, etc, complete all as specified and as directed.
111Cutting out cracks to V section in existing roofs or terracing ,cleaning out ,wetting, grouting with cement and sand slurry 1:3, complete all as specified and as directed.
112M&L for brushing neat cement slurry with 3.0 Kg of cement per Sq.meter, complete all as specified and as directed.
113M&L 25 mm thick PCC 1:2:4, type B0 (using 12.5mm graded stone aggregate) as in floor finished even and fair with out using extra cement , complete all as specified and as directed.
114M&L for 20 mm thick bedding layer in CM 1: 4, complete all as specified and as directed.
115M&L priming surfaces and applying normal treatment (for moderate condition ) for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforment with polyster non woven fabric (wt not less than 150 gms/sqm) laid on primed surfaced application including preperation of new surface of membrane and applying two coats of Alumminium paint, complete all as specified and as directed.
116Dismantling plain or corrugated steel sheeting any gauge thickness including nanital or similar pattern, complete all as specified and as directed.
117S &F Pre-painted galvanum aluminum zink coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550MPa as in roof covering /clading to walls fixed with self tapping screws complete all as specified and directed.
118S &F Pre-painted galvanum aluminum zink coating GI based corrugated plain sheet 0.50mm thick of an colour having tensile strength of 550MPa as in roof covering /clading to walls fixed with self tapping screws complete all as specified and directed.
119Providing 50mm thick insulation of water pipe line 20/25/32 mm dia pipe complete all as specified and directed by Engr in Charge. which includes of the following:- Export quality heat traceable (heat tape) , self regulating and auto cut with thermostate systemAluminum tapeK. Flex 19mmRock woolWire MashPolytheneCello tapeAluminum sheet 28 gauge
120Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as spfd and directed by Engr-in-charge.
121M&L for Point wiring for one light point or fan point or bell point controlled by one switch with PVC insulated FRLS copper conductor stranded cable of size 1.5 sqmm and including PVC casing/caping terminated in existing sunk CI/ pressed steel terminal boxes for fixing and 1.5 sqmm PVC insulated copper wire as earth wire connected to earth wire connected to earth folly and 3.00mm thick plastic lamiated sheet cover all as spfd and directed by Engr-in-charge.
122All as per item No. 121 here -in-before but 1.5 sqmm for one 3 pin 5 Amps socket outlet including 1.5 sqmm insulated copper wire as earth wire to the same earth dolly on same board.
123All as per item No. 121 here -in-before but 1.5 sqmm for one 3 pin 5 Amps socket outlet independent including 1.5 sqmm insulated copper wire as earth wire to the same earth dolly.
124M&L for point wiring for 3pin 15 Amps socket outlet independent with copper conductor cable PVC insulated multistrand 2.5 Sqmm with 2.5 sqmm PVC copper conductor as earth wire connected to earth dolly and including PVC casing/caping with sunk cast iron, complete all as specified and as directed.
125M&L for point wiring for 3pin 15 Amps socket outlet independent with copper conductor cable PVC insulated multistrand 4 Sqmm with 4 sqmm PVC copper conductor as earth wire connected to earth dolly and including PVC casing/caping with sunk cast iron, complete all as specified and as directed.
126M & L for Modular Switch one way single pole 6 Amp 1 Module 240 Volts, complete all as specified and as directed.
127M&L in replacement modular bell push 6A 1 module, complete all as specified and as directed.
128M & L for Modular Switch one way single pole 16 Amp 1 Module 240 Volts, complete all as specified and as directed.
129S & F Modular Sockets 6 A 2/3 Pin combined 2 module 240 Volts, complete all as specified and as directed.
130S & F Modular Sockets 6/16 Amp 2/3 Pin combined 2 module 240 Volts, complete all as specified and as directed.
131S & F for Modular white cover plate with frame 3 module, complete all as specified and as directed.
132S & F for Modular white cover plate with frame 6 module, complete all as specified and as directed.
133S&F ceiling rose surface bakelite two or three terminal , complete all as specified and as directed.
134M&L of Buzzer, Ding Dong AC. 230 volts, single pole , complete all as specified and as directed.
135S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 Amps MCB, complete all as specified and as directed.
136Supply and fixing surface/wall mounted LED fittings with LED tube 20 watts, 6000Kcapacity decorative ultra slim round profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient 4 feet long type bracket including neccessary conection prewired and making connection with 3 core copper flexible cable of appropriate size from ceilling rose/PVC connector to light fittings, complete all as specified and as directed.
137Supply and fixing surface/wall mounted LED fittings with INVERTOR LED tube 20 watts, 6000Kcapacity decorative ultra slim round profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient 4 feet long type bracket including neccessary conection prewired and making connection with 3 core copper flexible cable of appropriate size from ceilling rose/PVC connector to light fittings, complete all as specified and as directed.
138S&F in replacement of LED 36 watts recessed 2x2 luminaire WARM white to enhance the delight of occupants with comfortable experence through its design & glare free soft illumination and connection of 3 core copper wire with all accessories, complete all as specified and as directed.
139M&L for disconnectting serviceble LED 36 watts recessed 2x2 luminaire WARM/Cool white to to be deposited and after panling re-fixing same location LED 36 watts recessed 2x2 luminaire WARM white to enhance the delight of occupants with comfortable experence through its design & glare free soft illumination and connection of 3 core copper wire with all accessories, complete all as specified and directed.
140Taking down of existing UNSV post top lantern fitting of any type and any description, supply and fix LED post top lantern fitting 25W made in die cast aluminium spigot housing with decorative clear opal diffuser and IP65 protection complete incl fixing arrangement on pole and PCC (1:2:4) and necessary connection, complete all as specified and as directed.
141Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection pipes for hot and cold water etc and making good disturbed surface of wall with cement mortar 1:4 and finishes to match exisiting surface, complete all as specified and directed.
142M&L for disconnecting serviceble FCU from any location and deposited MES Store after paneling re-fixing to same location, complete all as specified and as directed.
143Replacement of MCB DB, SPN, 8 way sheet metal enclosures double door 230 V AC, 50 Hz AC with IP 54 and IK 09 rating having fully insulated copper busbar of rating 200 Amps, insulated neutral bar, earth bar and cable ties for cable management including polyuthrene gasket complete complete in all respect flushed in wall including cutting chases on wall for taking out old unsv DB and fixing of new DB and making good disturbed surface of wall with cement mortar 1:4 and finishes to match exisiting surface, complete all as specified and directed.
144MCB, SPN, AC, 240 volts \\"C\\" series capacity of 63 Amps, 10kA and making connections, complete all as specified & directed.
145MCB, SP, AC, 240 volts \\"C\\" series capacity of 6-32 Amps, 10kA and making connections, complete all as specified & directed.
146S&F for sub main wiring with 2 runs of FRLS PVC insulated multistrand, copper conductor cable of size 6 Sqmm along with one run of 6 sqmm PVC insulated cable 1100 volts multi-stranded copper conductor as earth wire complete all as specified and directed.
147Material and labour for sand in trenches as in cushioning to under ground cable spreading, levelling hand punning complete all as specified and directed.Note- Punned down thickness will be measured for payment purpose complete all as specified and directed.
148Supply and laying unreinforced pre cast concrete cable cover class LV type I flat size 250x150x40mm all as specified and directed.
149Supply and lay PVC insulated, heavy duty, LT XLPE galvanised steel strip armoured electric power cable of size 50 sqmm 3.5 core with stranded aluminium conductor 1100 Volts grade, jointed with cable glands, lugs etc., laid in trenches/drawn through pipe, with and including taking down old unserviceable cable, complete all as specified and directed.
150S&F GI tubing 40mm dia \\"light grade\\" with all fittings, laid in trenches, fixed on pole/under road crossing or passing through gutters etc, complete all as directed.
151Cutting the existing bituminuos road for passing of UG Cable in road crossing and making good the disturbed surface of road to its original specification complete all as directed.
152M&L in replacement for Earthing complete with galvanised steel earth plate electrode 60 cm X 60 cm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to and inclduing GI Strip 32X6 mm as earthing lead, by means of bolts, nuts, check nuts and washers of galvanised iron all as shown in electrical plate No 5 of MES SSR Part I and testing on completion inclduing excavation and earth work in any type of soil, PCC (1:3:6) type C1 chamber, MS frame and cover 6 mm thick in cement concrete (1:2:4) type B1 reinforced with welded steel wire fabric or XPM (weight not less than 4 Kg per Sqm) with cast iron frame, funnel with wire mesh, GI watering pipe 20mm dia medium grade and lugs complete all as specified and directed Note- (i) earth resistance not more than 1.0 OHMS.Writing of details on the surface of the pit with paint. (ii) In case earth resistance more than 1.0 ohms, the contractor wiil re earthing at no extra cost. (iii) On testing, if the earth resistance less than specified is not obtained, earthing will be regenerated at NO EXTRA COST till the desired earth resistance is obtained.
153All as per item No. 152 here-in-before but 4 mm GI wire complete all as specified & as directed.
154Diconnecting of all Lt Cable,MCCB from LT Panel, taking out the old LT panel and Supply, Installation, testing & commissioning in repairs LT Panel cubical type out door floor mounted weather proof totally enclosed, (CPRI approved) factory made and made out of 3 mm thick CRCA powder coated sheet and angle iron 40x40x6mm size complete with bus bar of Aluminium of suitable size of capacity 1000 Amps 3 Phase and neutral 415 Volts 50 Hz mounted on epoxy type insulators mounted on PCC flooring and angle iron base frame complete all as directed comprising of following accessories:- a) MCCB 250 Amps Cap, 4 Pole, 36 KA 415 volts-1 No for( I/C) c) MCCB 160 Amp cap, 4 pole, 36 KA, 415 Volts -1 Nosd) MCCB 120 Amp cap, 4 pole, 25 KA, 415 Volts - 2 Nos e) Digital Volt meter with selector switch(0-500V) - 01 Set f) Digital Amp meter with selector switch with necessary CT (0-500A) - 02 Set g) LED indicating lamp - 01 Set Note : (i) The Make of MCCB shall be Havells/L&T/ SIEMENS (ii) The rates shall deemed to be inclusive of suitable size copper wirinng/copper strips from Main I/C MCCBs to Change over switch, Change over switch to Main Bus bar and Bus Bar to Outgoing MCCBs complete all as specified and directed. (iii) The drawing & design of Panel, Make of complete accessories shall be approved by GE by the Contractor before order and execution at site.
155Deduct Schedule of Credit of Rs (-) 48183.00 (Minus) as listed in Schedule 'A' (Contd). Contract Sum shall be arrived after deducting the credit amount.Note :- Tenderers will not quote against this item being a firm amount. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58462695
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE 43.46 Lakhs
LAST DATE 02-12-2026
Authority
Authority Name Military Engineer Services
Work Description Tender For Addition/ Alteration To Building No P-487, P-488 & P-493 Of 22 Weu Leh Under Ge 865 Ews.
Basic Detail
Tender No 865/EWS(NIT-135/2026-27
Bidding Type Tender
Location
City leh
State Ladakh
Key Dates
Publish Date 10 Nov 2026
Submission Date 02 Dec 2026
Open Date 10 Dec 2026
Finance
Tender Value 43.46 Lakhs
Tender Fee 500
EMD 87000
Exemption Available
Document List
21ddf6a3-0039-44a9-b2ce-4600cd3c93a9.html
BOQ_895158.xls
TENDERNIT_135.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 10, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Dec 02, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 15 days
Dec 10, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 23 days

Tender Documents

Download All (ZIP) ↓
html

21ddf6a3-0039-44a9-b2ce-4600cd3c93a9.html

xls

BOQ_895158.xls

pdf

TENDERNIT_135.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender