Tender For Special Repair To Bldg No P-64 (Gym Hall) At Grc Under Ge (West) Jabalpur
Tender Value
80.65 Lakhs
Estimated cost
Bid Submission
08 Dec 2026
17 days left
EMD
1.46 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jabalpur → Madhya Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair To Bldg No P-64 (Gym Hall) At Grc Under Ge (West) Jabalpur
BOQ
| Sl. No. | Item Description |
| 1 | Schedule \\"A\\" |
| 2 | Removing old tar felt, all loose dirt,old roof tiles,including taking down cement plaster cleaning the concrete surface including removal & cleaning of vegetation, fungus,moss small trees etc from the roof top with wire brush, removing the strips of lightening conductor including refixing the same after repair work complete all as specified and directed by Engineer-in-Charge. |
| 3 | M&L for rendering 10mm thick on fair faces of brick or concrete surfaces in CM 1:4 mixed with water proofing compound on concrete roof surface finished fair and even to maintain the proper slope of roof surface etc complete all as specified and directed.(Note-WPC will be measurd and paid seprately) |
| 4 | Supply only integral water proofing compound |
| 5 | Applying evenly a coat of blown type bitumen at the rate of 0.30 kg per square metre |
| 6 | M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified. |
| 7 | Applying two coats of aluminum paint on top of membrane @ 0.20Kg/Sqm. |
| 8 | M&L for Cement concrete tiles 20cm x 20cm x 20mm thick with grey cement and pigment complete all as specified and directed by Engr-in-Charge. |
| 9 | M&L for Solid PVC Wall Lining(wall Panneling) consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site including PVC frame as per specifications and drawing |
| 10 | S & F in repair water closet (Squat Pattern) complete including provn of lime concrete bedding Orissa pattern size 580 x 440mm white with integral foot rests (excluding flush pipe or flushing cisterns) including connection to trap and flushing pipe anti syphonage pipe etc,with necessary connecting items, complete and making good to floor to match with existing complete all as specified and directed. |
| 11 | S&F in rep Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe)with necessary connecting items, fixed as in repair, complete all as specified. |
| 12 | S & F in repairs PVC High/Low level flushing cistern 10 litres capacity including all fittings i.e float valve, syphon, flushpipe, brackets all as specified and directed by EIC. |
| 13 | S&F in repair vitreous china wash basin white flat back size 580x450 and brackets, complete all as specified and directed by Engr-in-charge. |
| 14 | S&F in rep Vitreous China Urinal, Half stall type, white (including spreder, flush pipe and waste pipe) |
| 15 | S&F in repair,15 mm dia Pillar taps, cast copper alloy, with capstan heads, fancy type chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed |
| 16 | S & F in repair bib taps cast copper alloy CP with butterfly handle screwed down screwed for iron pipe or for brass ferrule 15mm bore dia all as specified and directed by EIC. |
| 17 | S & F in repair stop valves/angle cock cast copper alloy CP fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe 15mm bore dia all as specified and directed. |
| 18 | S&F in repair cast copper alloy chromium plated shower rose fancy type fixed to 15 mm bore pipe all as sspecified. |
| 19 | S&F in repair PVC floor trap square type with CP grating with or without hole including provision of jointing to waste pipes in run lead joint dia of outlet 75 mm, complete all as specified. |
| 20 | S&F in repairs PVC connections 15mm dia with brass nut on both ends and washers 450mm long all as specified and directed. |
| 21 | S&F in repair plastic water closet seat, white/black closet pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device. |
| 22 | S&F in rep Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified |
| 23 | S&F in repairs for Towel Rail 600mm long of PTMT fixed with Towel Rail 600mm long of PTMT fixed with screws and wooden/plastic cleats (Minimum weight 190gms) complete all as specified and directed . |
| 24 | S&F in repairs600mmx450mm bevelled edge mirror of selected quality glass, mounted on 5.5 mm thick PVC frame or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers all as specified and directed by EIC. |
| 25 | S&F in Repair Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed . |
| 26 | Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to store,complete all as specified and directed by Engr-in-Charge |
| 27 | Taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing or removal to store,complete all as specified and directed by Engr-in-Charge |
| 28 | Taking up or down 40 mm bore steel tubing and connections, including cleaning for refixing or removal to store |
| 29 | Supply & laying of CPVC pipes 16 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors including chase cutting and fixing with solvant suitable for CPVC pipe and brass treaded fittings for fixing taps and valves, complete all as specified and directed. |
| 30 | Supply & laying of CPVC pipes 20 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors including chase cutting and fixing with solvant suitable for CPVC pipe and brass treaded fittings for fixing taps and valves, complete all as specified and directed. |
| 31 | Supply & laying in repair of CPVC pipes 40 mm Outer dia, SDR 11 & Plain CPVC SDR 11 fitting on wall/ceiling or laying in floors including chase cutting and fixing with solvant suitable for CPVC pipe and brass treaded fittings for fixing taps and valves, complete all as specified and directed. |
| 32 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) |
| 33 | S & F in repair of 110 mm dia PVC (SWR) pipe single socketed in any length with rubber ring joints to wall complete all as specified. |
| 34 | S & F in repair of 75 mm dia PVC (SWR) pipe single socketed in any length with rubber ring joints to wall complete all as specified. |
| 35 | S & F in repairs PVC (SWR) bends 110 mm dia bore any radius with access door all as specified and directed. |
| 36 | S & F in repairs PVC (SWR) bends 75 mm dia bore any radius with access door all as specified and directed. |
| 37 | S&F in repairs 110 mm bore PVC (SWR) junction single (Single T) equal or unequal. |
| 38 | S&F in repairs 75 mm bore PVC (SWR) junction single (Single T) equal or unequal. |
| 39 | S&F in repairs 110 mm bore PVC (SWR) junction single (Single T) equal or unequal with access door. |
| 40 | S & F in repairs PVC (SWR) branch piece, single (double Y) 110 mm dia equal or unequal |
| 41 | S&F in repairs 75 mm bore PVC (SWR) junction single (Single T) equal or unequal with access door. |
| 42 | S & F in repairs PVC (SWR) branch piece, single (single Y) 110 mm dia equal or unequal |
| 43 | Taking down shutter n exc 1.00 sqm of any description complete all as specified and directed by Engr-in-charge |
| 44 | Taking down shutter exc 1.0 sqm but n exc 2.0 sqm each of any description complete all as specified and directed by Engr-in-charge |
| 45 | Taking down Chowkhats or frames not exc. 1.5 sq. m each |
| 46 | Taking down Chowkhats or frames exc 1.5 sqm but not exc.4.0 sq. m each |
| 47 | S & F powder coated (min thickness of powder coating 50 micorn) Aluminium door, window,ventilato,partion frame with one or more rebates and shutter incl jointing cleat for fixing etc. including making good to the disturbed surfaces and matching existing treatment (cemnt base paint/distemper/white wash/plastic paint) etc complete all as specified and directed |
| 48 | S&F powder coated aluminum window ,ventilator,door,partion shutters, fixed type without sash bars, aluminium section weighing 0.55 Kg/ Rm including necessary jointing cleats, glazing clips, ruber packing, anodised aluminium snap beading, screws etc. including making good to the disturbed surfaces complete all as specified and directed. |
| 49 | S & F Factory made internal PVC door frame of size 50x47mm single revated made out of extruded 5 mm PVC foam sheet, mitre cut at two corners and jointed with 02 Nos of 150 mm brackets of 15x15 mm MS square tube. The two vertical door profiles are to be in forced with 40x20 mm MS tube of 19 gauge through out the frame complete all as specified and as directed by Engineer-in-Charge. |
| 50 | S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. complete all as per specification & drawing and as directed by Engineer-in-charge. |
| 51 | M&L for 35mm thick factory made second class hardwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed by Engr-in-charge |
| 52 | S&F factory made plain framed ,35 mm Panelled shutter (three Panel) with lock rail of 9 mm B.W.P. commercial ply or 12 mm veneered patticle board with commercial veneering on both face , the size of rail and stile as per IS: 1003 (Part 1) kiln seasoned and chemically pressure treated complete all as specified and directed by Engr-in-charge |
| 53 | S&F second class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engr-in-charge |
| 54 | S & F Pressed steel frames made of 1.25 mm thick MS Sheet size 125x60mm for doors, with double rebates including necessary fixing lugs, hinges, lock strike plate etc, M & L for providing PCC 1:2:4 type B0 (using 12.5mm graded stone agg) to fill the frame & making good complete all as specified & directed by Engr-in-Charge. |
| 55 | S & F Pressed steel frames made of 1.25 mm thick MS Sheet size 105x60mm for doors, with single rebates including necessary fixing lugs, hinges, lock strike plate etc, M & L for providing PCC 1:2:4 type B0 (using 12.5mm graded stone agg) to fill the frame & making good complete all as specified & directed by Engr-in-Charge. |
| 56 | S&F aluminium alloy anodized sliding door bolt with hasp, staples (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts or extruded sections or cast aluminium alloy length of bolt 250mm complete all as specified and directed by Engr-in-charge. |
| 57 | S&F Butt hinges stainless steel 100 mm long complete. |
| 58 | All as per item No above but 75mm long size complete. |
| 59 | S&F Aluminium anodised barrel tower bolts of extruded section 200mm long complete, |
| 60 | S&F Aluminium anodised barrel tower bolts of extruded section 150mm long complete, |
| 61 | S&F and in repair Aluminium handles cast type anodised of 150mm complete. |
| 62 | Hacking out old broken glass (any the size quality or description) from metal frame including punching or drilling out old glazingpins/spring clips and providing and fixing new ones all as specified and directed by Engr-in-charge. |
| 63 | S&F 3 mm figured glass, pin head type and glazing with beads fixed with m in squares n exc 0.5 sqm in each pane complete all as specified and directed. |
| 64 | S & F Sheet glass 4 mm thick ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane.complete all as specified and directed by Engr-in-charge |
| 65 | M&L 10mm thick toughned glass as in hinged doors, partitions, automatic doors and similar work including cutting to shape, drilling holes required |
| 66 | M&L 12 mm thick toughned glass as in hinged doors, partitions, automatic doors and similar work including cutting,grinding,rounding off edges to shape, drilling holes required,.complete all as specified and directed by Engr-in-charge |
| 67 | M&L Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers |
| 68 | S & F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tacks or galvanised wire staples complete all as specified and directed by Engr-in-charge |
| 69 | S & F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tacks or galvanised wire staples complete all as specified and directed by Engr-in-charge |
| 70 | S & F and in repair Door spring ordinary rat tail rod pattern springs including roller and roller plate complete of mild steel 300 mm long complete including necessary welding if fixed in steel door.complete all as specified and directed by Engr-in-charge |
| 71 | M&L for floor door spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed to aluminium door etc. complete all as specified and directed. |
| 72 | S&F in repair door closer hydraulically regulated designation No-2 universal type of aluminium body fixed to door frames with screws or by welding suitable for door shutters of 701-805 mm in width & wt between 36-60 kg complete all as specified and directed by Engr-in-charge. |
| 73 | Welding in repairs n. exc 2.5cm in length , on metal of thickness n exc 6 mm , for fixing of door hing, door spring , welding in iron doors complete all as specified and directed by Engr-in-charge |
| 74 | S&F in repair 18-20 mm thick Acrylic Pvc Celuka Board,prelaminated one side with decorative choice lamination & other side balancing white lamination approved texture as in kitchen cabinet,Cupboard etc ( with shelves and partition ) including complete all as specified and directed by Engr-in-charge |
| 75 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises |
| 76 | M&L Non - skid coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in cement mortar (1:4) |
| 77 | M&L Non - skid coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in cement mortar (1:4) |
| 78 | M&L non skid coloured ceramic tiles 300x300/400x400 mm x 7mm thick,in floors set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in CM 1:6, complete all as specified. |
| 79 | M&Lnon skid coloured digital ceramic tiles size of tiles 450x350/300x600x7mm thick vertical surface such as in skirting/dado etc over and including 10 mm thick cement plaster in CM 1:4,, all as specified and directed. |
| 80 | M&L for Granite tiles 18 to 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 15 mm thick screed bed of CM (1:4) , as in tread and riser of staircase,steps , jambs, pillars, windowcills,partion complete complete as specified and as directed. |
| 81 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations |
| 82 | Demolition of cement concrete (unreinforced) in ground floor or pavings n exc 15 cm thickness (below or above ground level) |
| 83 | M&L 75 mm thick Cement concrete type C-2, 1:3:6 (40mm graded aggregate) as in plinth protection,flooring etc,complete all as specified |
| 84 | M & L for 25 mm thick PCC 1:2:4 type B-0 using 12.5mm crushed stone aggregate as in leveling course complete all as specified and as directed. |
| 85 | M & L for 75 mm thick PCC 1:4:8 type D-2 using 40mm graded aggregate stone as in subbase, Hard standing and similar works |
| 86 | Demolition of brick /stone walls built in cement mortar incl all quoins, arches, pillars etc, but excluding ashler facings, dressed stonework and precast concrete articles |
| 87 | M&L Brick work using old size bricks with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6, complete all as specified and directed. |
| 88 | Dismantling of Stone slabs and kota stone,Cuddappa stone, Granite, Chequered tiles, Paver block, etc of any description or thickness in floors, aprons etc. laid bedded and pointed in any cement mortar complete all as specified and as directed. |
| 89 | M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, over Screed bed or bedding layer of cement mortar(1:6), 15 mm thick for laying floor finishes, including rubbing and mirror polishing complete all as specified and directed |
| 90 | M&L Machine cut kota stone slab 20-25mm thick as in riser of steps, skirting, dado and pillar, over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, over 10 mm thick cement plaster (1:4), on fair faces of brick work or concrete surface as backing, including rubbing and polishing complete all as specified and directed |
| 91 | M&L for Wooden FlooringSurface Board:- Made of Kiln Seasoned (moisture containt of approximately 14% at the time tiome of dispatch), Treated Maple Wood finished with 24mm thick, 57 to 83 mm wide and in random length in tongue and groove shape. The edges of the boards will have a finger lock groove and the bottom side with air pass groove and treated with special anti termite and water resistant lacquer. Maple wood is the hardest of hard woods and is the recommended wood for squash court.inclunding dismantling old wooden flooring and making good for new. All major tournaments are played on Maple Wood Floor only. The Under Frame:- Made of commercial quality pine wood runners of 70 mm x 45 mm, treated with anti-termite solution and fixed on the bottom side with 10 mm thick air cushioned pads, stappled through the two wings at 300 mm x 300 mm Installation:- IPS subfloor treated with a vapour barier to be placed on the leveled IPS sub-floor before laying the under frame. The runners having air cushion pads to be placed on the vapour barier in perfect level at 350 mm in 1 direction. The surface board to be screwed to the runner through the tongue only and will lock the screwed tongue by the groove of adjoining board. Ends of the boards will be locked by inserting the wooden fingers through the edge grooves and fixed with suitable adhesive. An expansion of 8 to 10 mm to be left open between the wooden flooring and the surrounding tiled area / wallsFinishing:- After laying the flooring, the floor boards will belevelled to a uniform surface and complete all as specified and directed by Engr-in-Charge |
| 92 | SYNTHETIC TENNIS COURTPRIMER: 100% synthetic court of Acrylic (KDF) based emulsion toimprove bond of acrylic court system to the concrete or asphalt surfaces.RESURFACER: 1 synthetic court of Acrylic (KDF) Resurfacer 367-30 for filling and smoothing asphalt or concrete surfaces inpreparation for Acryflex ITF Approved Tennis court system. Andalso fills the surface chips, voids and conceals repairs whileproviding a smooth surface for color coatingCUSHION COAT: 4 Layers of synthetic court of Acrylic (KDF)cushion for asphalt or concrete surfaces in preparation forsynthetic court of Acrylic (KDF) ITF approved systemPRECOAT: 2 layers of synthetic court of Acrylic (KDF) basedtextured Tennis topcoat. Ideal for color coating Tennis courts andother sport pavement surfaces.OVERLINE : 100% synthetic court of Acrylic (KDF)) based highhiding line paints. |
| 93 | M&L for rendering 10mm thick on fair faces of brick or concrete surfaces of wall in CM 1:6, complete all as specified and directed by Engineer-in-Charge. |
| 94 | M&L for rendering 15 mm thick CM 1:4 on fair faces of brick work or concrete surfaces external surface even & fair and using integral water proofing compound. |
| 95 | M&L for 5mm thick rendering on concrete surface of ceiling in CM 1:3 and rendering is to be finished even and smooth with out using extra cement,.complete all as specified and directed by Engineer-in-Charge. |
| 96 | M & L for preparation of new plasterd or unplastered surfaces of ceiling and applying three coat of white wash complete all as specified and directed |
| 97 | M & L for preparation of old plasterd or unplastered surfaces of ceiling and applying two coat of white wash complete all as specified and directed |
| 98 | M&L for french polish over wooden surfaces, complete all as specified and directed by Engr-in-Charge |
| 99 | M &L for preparation of old wooden surfaces of any description not otherwise described over 10cm width or girth and applyinbg one coat of synthetic enamel paint any tint all as specified and directed. |
| 100 | M &L for preparation of new wooden surfaces of any description not otherwise described over 10cm width or girth and applyinbg two coat of synthetic enamel paint any tint over pink primer all as specified and directed. |
| 101 | M &L for preparation of new steel surfaces of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint of any tint all as specified and directed. |
| 102 | M &L for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint of any tint all as specified and directed. |
| 103 | Complete Removal of existing treatment of old wall surfaces,complete all as specified and directed |
| 104 | Preparing old wall surfaces complete all as specified and directed. |
| 105 | Preparing new wall surfaces complete all as specified and directed. |
| 106 | Priming plastered and other surfaces with alkaliresistant priming paint. |
| 107 | M&L for 1 mm thick wall care putty on wall,complete all as specified and directed |
| 108 | M&L for 1 coat Oil emulsion distemper on wall, complete all as specified and directed |
| 109 | M&L for subsequent coat Oil emulsion distemper on wall, complete all as specified and directed |
| 110 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm, including preparing of new or old surfaces, complete all as specified and directed by Engr-in-Charge |
| 111 | Dismantling Wall panelling and similar work |
| 112 | Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed |
| 113 | Internal Electrification |
| 114 | Taking down carefully any type point wiring (light, fan, socket bell or power) , complete with fitting such as switches ceiling roses,lamp holders sockets,regulators,call bell light fitting with PVC conduit surface /concealed or wooden pattens including sunken cast iron /pressed steel terminal boxes etc and making good the disturbed surfaces of walls, roof, floors etc to match with the existing surfaces all as specified and directed by Engineer in charge. |
| 115 | Taking down the ceiling fan in situ and submitting to MES store complete all as specified and directed. |
| 116 | Taking down carefully Main switch and Distribution boards/meter any make and size . |
| 117 | Taking down carefully Old unserviceable any type sub main wiring with wooden batten/PVC surface conduit of any size and making good the disturbed surfaces of walls, roof, floors etc to match with the existing surfaces complete all as specified and directed by Engineer in charge. |
| 118 | M/L for Sub Main Wiring two single core PVC insulated copper conductor FRLSH cable of size 6.0 Sqmm multistranded copper conductor two run drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 25mm dia with all conduit fitting,fixing accessories and one run of 6.0 Sqmm multistrand copper conductor cable as continuous earth wire complete all as specified and directed by Engineer in charge Note :-Two Nos of 6.0 Sqmm Wire and one No of 6.0 Sqmm Earth wire in One RM length Measured as one unit length. |
| 119 | M/L for Sub Main Wiring with two single core PVC insulated copper conductor FRLSH cable of size 4.0 Sqmm multistranded copper conductor drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 20mm dia with all conduit fitting,fixing accessories and 4.00 Sqmm multistrand copper conductor cable as continuous earth wire complete all as specified and directed by Engineer in charge Note :- Two Nos of 4.00 Sqmm Wire and One No of 4.0 Sqmm Earth wire in One RM length Measured as one unit length. |
| 120 | Material & Labour for point wiring with three layer PVC Insulated 1.5 Sqmm multi-strand copper conductor FRLSH cable 1100 Volts grade drawn into and concealed PVC conduits medium grade not less than 20mm( ISI marked) including all fitting and fixing accessories including 1.25 mm thick sunken pressed steel terminal boxes/Modular metal flush box duly painted with two coats of anti-corrosive paint outside and two coats of aluminium paint inside with and including 3mm thick hylam brand laminated white bakelite sheet cover for mounting switches, sockets, fan regulators fixed with CP screws with cup wahsers and PVC insulated 1.5 Sqmm multi-strand copper conductor cable as earth wire and making good the disturbed surfaces with cement sand mortar 1:3 to match with the existing surfaces complete all as specified & directed by Engineer-in-charge |
| 121 | (a) One light point/Bell point controlled by one switch. |
| 122 | (b) One fan point controlled by one switch. |
| 123 | (c) One socket point controlled by one switch on same board. |
| 124 | (d) One socket point controlled by one switch on Independent board. |
| 125 | Description all as per item No 7 here in befor but with 1100 volts grade copper standard conductor cable of size 2.5 Sqmm with 2.5 Sqmm solid copper conductor PVC for 3 pin switch socket outlet15 Amp independent board complete all as specified and directed by Engineer in charge . |
| 126 | S & F in replacement of bell ding dong AC 230 volts single pole one way complete all as specified and directed by Engineer in charge. |
| 127 | S & F in replacement of Switch piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and directed by Engineer in charge. |
| 128 | S & F in replacement of Socket outlet 3 pin, 5 Amps and AC 230 volts flush type complete all as specified and directed by Engineer in charge |
| 129 | S & F in replacement of switch socket combination 5 in 1 pin 5 and 16 Amps AC 230 volts flush type complete all as specified and directed by Engineer in charge |
| 130 | S & F in replacement of Ceiling rose surface bakelite 65 mm x50 mm three terminal AC 230 volts flush type complete all as specified and directed by Engineer in charge |
| 131 | Supply anf fixing in replacement of LED lamp holder all as specified and directed by engr-in-charge. |
| 132 | Supply and fixing in replacement of decorative wall light fitting WITH LAMPS 9 WATT made up of Polycarbonate , City-1 , Cylindrical shape , complete with fixing arrangements on wall all as specified and directed. Make:City 1 of havells or equivalent in bajaj ,philips |
| 133 | Supply and fixing LED lights fitting 1x 22W,Min 120 lumens/watt 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete completion as per all as specified and directed. |
| 134 | S & F in repair of LED Decorative /mirror light fitting diffuser 2 feet, 10 watt 220 V along with fixture Surface mounted suitable for indoor aplication , connector block, etc . Complete with all accessories internally pre-wired and including round wood block, connecting up with three core flexible flexible copper conductor cable suitable size complete all as specified and directed by Engineer in charge. |
| 135 | S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer in charge. |
| 136 | Supply and fixing LED street light fitting 35 watt 130 LM/watt 6000K 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed. |
| 137 | S&F in replacement of sheet steel enclouser distribution boards, double door factory made VTPN 4 way 3 phase 415 volts 4 way with 200 amps rating copper bus bar and PVC insulated copper jumpers of suitable size from the MCCB to the out going circuits one incoming MCCB 100 amps , circuits comprising of 3 phase 4 wire of suitable rating all as specified and directed. |
| 138 | S & F MCB TPN 40 to 100 Amps, 415 Volts, minimum 10 KA, \\"C\\" series rupturing capacity and to be housed in DBs catered here in before complete all as specified and directed :-(Make- Legrand / L&T / Havells)(Note :- Proper and suitable size cablecopper lugs to be fixed with MCBs are included in unit rate of each MCB of any rating) |
| 139 | Supply and fixing ceiling fans complete with blades, 5 RM down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor(BLDC) |
| 140 | Supply & Fixing in repair sheet metal enclosure MCB DB double door [Acrylic], single pole and neutral, 240 volts, 12 way with 200 Amp, 10 KA breaking capacity rated bus bar with blanking plate wherever required and IP-43 degree protection complete all as specified & directed. |
| 141 | Supply and fixing amp rating 240V, 40-63 Amps, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning. |
| 142 | S&F in replacement of SP 6 To 32 AMP rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified & directed. |
| 143 | Supply & Fixing in replacement of single pole sheet metal enclosure with a two pin and earth plug and socket complete with 01 number single pole MCB 20 Amps complete all as specified & directed. |
| 144 | Earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including galvanised iron earth wire 4 mm dia by means of nut, bolts, check nuts and washers of galvanised iron or steel complete all as specified and directed including testing on completion including the material and labour of the following : - (a) Excavation and earth work for drilling hole for electrode in any type of Soil. (b) PCC pit in cement concrete 1:2:4 type B-1, Pre cast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than1.87 Kg/ Sq meter. (c) Funnel with watering pipe of GI 20 mm nominal bore light grade and lugs etc complete all as specified and directed (d) 15 mm nominal bore medium grade GI protection pipe 5 meter long for protection of earthing lead complete all as specified and directed. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing. |
| 145 | S & F in replacement of bell push piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and directed by Engineer in charge. |
| 146 | Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300 mm sweep with, blades, and frame and louvers including making holes of suitable size and making good the disturbed surface and shutters including electric connection with pvc flexible twin core copper wire from ceiling rose to Exhaust fan, nut & bolt complete all as specified and as directed.Make:Bajaj,havells or equivalent. |
| 147 | Supply and fixing Single phase Exhaust fan heavy duty AC 230 volts 300 mm sweep, PVC body complete with PVC louvers including making holes of suitable size and making good the disturbed surface and shutters including electric connection with pvc flexible twin core copper wire from ceiling rose to Exhaust fan, nut & bolt complete all as specified and as directed.Make:Bajaj,havells or equivalent. |
| 148 | External Electrification |
| 149 | Taking Down old unservicable cable of any size complete all as specified and directed by Engineer in charge |
| 150 | Supply , laying and testIng cable XLPE insulated , screened, PVC bedded , galvanized , steel strip or wire armoured, electric power cables ( Heavy duty ) 1100 volts grade with stranded aluminium conductor of size 3.5 core 25 Sqmm complete all as specified and directed by Engineer in charge |
| 151 | Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, for laying of pipe, cable etc or n. exc.10 Sqm on plan and n. exc. 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in soft /loose soil complete all as specified and directed. |
| 152 | Removing excavated material to a distance n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and as directed. |
| 153 | Returning , filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed. |
| 154 | Supply and spreading clean and dry fine sand free from sharp materials (unwashed) laying in trenches around the cable for cushioning in trenches, laid to a uniform thickness of 23cm (15cm under the cable & 8cm over the cable) and gently punned down to 18 cm thickness complete all as specified and as directed. |
| 155 | Supply and laying un-reinforced precast concrete cable covers, Class LV, Type I, flat, size 250 mm x 150mm x 40mm complete all as specified and as directed. |
| 156 | Supply,laying & fixing double wall corrugated (DWC) pipes made of high density polythethyline (HDPE) with all accessories i.e. all type of joints,Sockets,Elbows,bends and End caps etc. size 50 mm outer dia and 38 mm inner dia complete all as specified and directed. |
| 157 | Supply and fixing LED flood light 120 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp. |
| 158 | Schedule of credit amount of Rs 1,37,416.00 to be deducted during AOC Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 09, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedDec 08, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender