Tender For General-Thanneermukkom Swb-46 Ft Radial Lock Gate Shutter Fixing By Fabrication And Installation Of Embedded Parts With Ss Anchoring Rod And Other Associated Works. -General Mechanical Work
Tender Value
71.18 Lakhs
Estimated cost
Bid Submission
17 Nov 2026
5 days left
EMD
50000
Bank guarantee accepted
Document Fee
2760
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Alappuzha → Kerala
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for General-Thanneermukkom Swb-46 Ft Radial Lock Gate Shutter Fixing By Fabrication And Installation Of Embedded Parts With Ss Anchoring Rod And Other Associated Works. -General Mechanical Work
BOQ
| Sl. No. | Item Description |
| 1 | Formation of Sand Bund on Both Side of 46’ Lock Chamber, Bailing Out of Water |
| 2 | 15.3:Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge. |
| 3 | OD20647/2026-2027:Providing needle shutter support on Both Side of 46feet Lock Chamber for Sand Bund with ISMB300 x 140, ISMC 200 x 75 and MS Flat 6 x 100 mm including 1/5 th cost of MS materials and conveying charges, puddle clay filled in 1.0m width between adjacent needle shutter to support bund including labour for dismantling the bund after completion of work as the direction from the departmental officers at site. |
| 4 | OD19172/2026-2027:BAILING OUT WATER USING PUMP ABOVE 30HP AND UP TO 40HP - Bailing out water with engine and pump set above 30HP and up to 40HP, including conveyance to site and erection, cost of fuel, lubrication oil and other stores, pay of staff etc complete |
| 5 | OD19170/2026-2027:Bailing out water using pump above 5 HP and Up to 10 HP-Bailing out water with engine and pump set above 5HP and up to 10HP, including conveyance to site and erection, cost of fuel, lubrication oil and other stores, pay of staff etc complete |
| 6 | Hire charges of Department Dredger D4/D8 |
| 7 | OD19946/2026-2027:Incidental charges for transit and preparation |
| 8 | OD19947/2026-2027:Provision for 200 Litre capacity barrel for the work |
| 9 | OD19948/2026-2027:Cost of Engine Oil |
| 10 | OD19949/2026-2027:Cost of gear oil for the work |
| 11 | OD19951/2026-2027:Tugging charges of deptl. dredger No. D4/D8 and its accessories including empty running, waitingetc.Hire charges of the tug having speed of 3km/hr; Rate per day is 1220000x38/200x100=Rs.2318. |
| 12 | OD19954/2026-2027:Cost of HSD: Dredgingη per per hr=50 m3 average, HSD needed per hour=40 Ltrs. total hrs required=4032m3/50m3=80.64hrs., hence,net diesel qty= 40x80.64=3225.6 ltrs.{HSD requirment is40ltrs/hr}+Addnl 180.4litres of hsd (20.16hrs) ,for gen set provision is also included for the usagewhile tugging & preparation work,hence net hsd requirement =3406litres. |
| 13 | OD19956/2026-2027:Conveyance of HSD & Oil for the work by lorry |
| 14 | OD19952/2026-2027:Hire charge of the country boat with boatman for travelling crews, conveying diesel and otheraccessories etc. |
| 15 | OD19957/2026-2027:Hire charge of the motor boat with boatman for travelling crews, conveying accessories etc. forpositioning the dredger in heavy flow through river due to unexpected climatic conditions suchas heavy rains etc.. |
| 16 | OD19996/2026-2027:Repair and Maintenance charge of dredger (2.5% of total hire charge of dredger)Hire charges of department dredger no.D4/D8 (a) for 8days- Rs.55,663 x 8 days=Rs.445304(b) for extra hours- 0.64 hrs x Rs.8,350=Rs.5344/- total hire charges (a+b) Rs.450648/-,Repair & mace.charges =450648*2.50 /100= 11266/-. |
| 17 | Removal of Slit/Mud From Lock Chamber, Dismantling of Radial Gates, Demolishing the Existing Civil Structure for Anchoring Trunnion Bracket and Concreting etc. |
| 18 | 2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil |
| 19 | OD19186/2026-2027:Dismantling/Assembling of the existing lock gate and associated its operating piston, cylinder, hydraulic oil hose etc. taking out from the lock chamber and conveying to safe place up to 100 Mtr etc complete |
| 20 | 15.3:Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge. |
| 21 | 26.31.2:Providing, mixing and applying bonding coat of approved adhesive on chippedportion of RCC as per specifications and direction of Engineer-In-chargecomplete in all respect.Epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make |
| 22 | 26.29.2:Cleaning of reinforcement from rust from the reinforcing bars to give it a totalrust free steel surface by using alkaline chemical rust remover of approvedmake with paint brush and removing loose particles after 24 hours of itsapplication with wire brush and thoroughly washing with water and allowingit to dry, all complete as per direction of Engineer-In-Charge.Bars above 12 mm diameter |
| 23 | 5.22.4:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelHot rolled deformed bars |
| 24 | 50.5.33.2:Providing and laying in position machine batched and machine mixed design mix M-20 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. Note:- Cement content considered in this item is @ 330 kg/cum. Excess or less cement used as per design mix is payable or recoverable separately. All work above plinth level upto floor V level |
| 25 | OD19187/2026-2027:Supply of SS 316L Nut and Washer |
| 26 | 85.105:Supply of SS plates of grade 304L including cost of conveyance charges |
| 27 | OD19189/2026-2027:Supply of SS 316 L rod of 32 mm diameter and 750 mm length with M30 thread at one end. |
| 28 | OD19190/2026-2027:Fabrication and fixing of stainless-steel rod in SS 304 L grade and accessories, etc. for the same as per approved specifications, drawings and directions of dept. officer at site including cost of labour, machinery for welding, shearing, grinding, etc. all lead and lifts, conveyance, incidental and handling, etc. complete but excluding cost of material already supplied. |
| 29 | Overhauling of Trunnion Pin and Bush. |
| 30 | OD19179/2026-2027:Supply of Aluminum Bronze Bush of OD=195, ID=160, L=270 for Trunnion |
| 31 | OD19180/2026-2027:Overhauling of one number Trunnion assembly unit. |
| 32 | Replacement of Rubber Seal and Limit Switch Repair etc. |
| 33 | OD28365/2026-2027:Dismantling old rubber seal-chipping cutting and removing the bolt and nut dismantling takingout and stacking old rubber seal from the gate with out any damage. including cost of all labourtools and wccessories and lead lift and incidental and conveyance etc complete |
| 34 | 85.116:Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing |
| 35 | OD28366/2026-2027:Supplying and fixing in correct position with specified initial interface L-type bulb nose rubberseal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour andmachinery and incidental and conveyance charges complete as per approved specifications anddrawings |
| 36 | OD28367/2026-2027:Supplying and fixing in correct position with specified initial interface P-type bulb nose rubberseal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour andmachinery and incidental and conveyance charges complete as per approved specifications anddrawings |
| 37 | OD28459/2026-2027:Supply, Fabrication, erection and assembling in correct position and alignment by welding Stainless Steel Parts in 304L Grade as per approved specifications, drawings and directions of deptl officer at site including cost of all materials, labour, machinery for planing, welding,shearing, grinding etc,lead and lift, conveyance, incidental and handling etc complete. |
| 38 | OD19169/2026-2027:Supplying and fixing in correct position of limit switches for lock gate. |
| 39 | Providing Roller Guide and Water Jet Arrangement for Cleaning the Roller Track |
| 40 | OD19181/2026-2027:Fabrication, Supply, erection and assembling in correct position and alignment by welding SS Roller Guide parts in 304L Grade as per approved specifications, drawings and directions of deptl Officer at site including cost of all materials, labour, machinery for planing, welding, shearing, grinding etc, lead and lift, conveyance, incidental and handling etc complete |
| 41 | OD19182/2026-2027:Supply and fixing of Brine solution Centrifugal Hi-Flow Monoblock PP Pump of 1.1kW/ 1.5HP with PVC Hose Pipe of 2 Inch dia. and SS 304 Pipe for Jet arrangement for Lock gate. |
| 42 | OD19183/2026-2027:Drilling hole in upper girder of lock gate for draining out water. |
| 43 | Replacement of Hydraulic Hose, Relay, Switches etc |
| 44 | OD19184/2026-2027:Supplying and fixing of Hydraulic Hose for Power Cylinder, Switches and Relays for Control panel. |
| 45 | Supply, Fabrication, Erection of Operator Room door and Painting of exposed area of Door, Power Cylinder Body, Head etc. |
| 46 | OD19173/2026-2027:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges. |
| 47 | OD19177/2026-2027:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges |
| 48 | OD19174/2026-2027:Fabrication and supply of Cabin door in structural steel conforming to IS2062Gr as per approved specifications and direction of departmental officers at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied. |
| 49 | OD19176/2026-2027:Painting all the exposed surfaces of the door and piston area with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site. |
| 50 | OD19175/2026-2027:Fixing locking system and pad lock |
| 51 | Supply of Hydraulic power cylinder piston |
| 52 | OD19178/2026-2027:Supply of Machined Chrome Plated Piston Rod Dia 110x Stroke 4350 mm |
| 53 | Supply, fabrication and erection of SS embedded parts |
| 54 | OD27644/2026-2027: Supply, Fabrication, erection and assembling in correct position and alignment by welding SS Embedded parts in 304L Grade like roller track, seal track, seal seat etc as per approved specifications, drawings and directions of dept officer at site including cost of all materials, labor, machinery for planing, welding, shearing, grinding etc, lead and lift, conveyance, incidental and handling etc complete |
| 55 | Trial Run |
| 56 | OD19185/2026-2027:Alignment and trial run of Lock Gate including cost of all materials, labour charges and hire ofmachinery etc. complete for the smooth operation of the shutter Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 09, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysNov 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender