Agriculture Government Departments Closing in 3 days TDR #58458130

Tender For General-Alappuzha District Panchayath 2024-25Ambalappuzha Division- Project No 861/2024-25 Construction Of Motor Thara And Shed In Nanekkad Padasekharam Ward No.7 Ambalappuzha North Grama Panchayath Alappuzha-General Civil Work

Issued by Government Departments · Alappuzha, Kerala
Tender Value
10.57 Lakhs
Estimated cost
Bid Submission
24 Nov 2026
3 days left
EMD
26449
Bank guarantee accepted
Document Fee
2760
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Alappuzha → Kerala
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender for General-Alappuzha District Panchayath 2024-25Ambalappuzha Division- Project No 861/2024-25 Construction Of Motor Thara And Shed In Nanekkad Padasekharam Ward No.7 Ambalappuzha North Grama Panchayath Alappuzha-General Civil Work

BOQ

Name of Work:- GENERAL-Alappuzha District Panchayath 2024-25Ambalappuzha Division- Project No 861/2024-25 Construction of Motor thara and Shed in Nanekkad padasekharam Ward No.7 Ambalappuzha North Grama Panchayath Alappuzha-General Civil Work
Sl. No. Item Description
1Parakuzhy
2OD3663/2026-2027:RING BUND Type-I-Putting up ring bund as per approved shape 2.5m bottom width, 1m topwidth using empty gunny/polythene bags filled with earth placed in 2 rows at 0.6m apart andfilled in between with puddle clay to form bund for an average height 2.00m including labourdismantling the bund after completion of the work etc. complete (Modified data FINAL APPROVEDCOMMON OBSERVED DATA'S April 2023 Irrigation 5.1)
3OD3525/2026-2027:Bailing out water using 5 HP pump- Bailing out water with 5 HP engine and pump set including conveyance to site and erection,cost of fuel,lubrication oil and other stores,pay of staff etc complet.Standard data 60.2.2 modified.
45.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete
55.1.3:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size derived from natural sources)
65.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more
7Motor shed
82.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil
9OD3527/2026-2027:Modified data of 60.7.1 DRY RUBBLE MASONRY - Dry rubble without concrete levelling course masonry with good quality blasted rubble including packing to compactness to lines and levels cost and conveyance of all materials labour charges etc. complete as per direction of Departmental officers at site.
10OD3528/2026-2027:Random rubble masonry with hard stone in foundation and plinth including levelling up with out cement concrete 1:6:12 (up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)
112.25:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.
1250.2.25.1:Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge
134.3.2:Centering and shuttering including strutting, propping etc. and removal of form work for:Retaining walls, return walls, (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc.
144.3.3:Centering and shuttering including strutting, propping etc. and removal of form work for:Columns, piers, abutments, pillars, posts and struts
154.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)
165.1.3:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size derived from natural sources)
175.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more
1850.6.2.1:Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1 cement :6 coarse sand) etc complete
1913.4.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 coarse sand)
2013.44.1:Finishing walls with water proofing cement paint of required shade:New work (Two or more coats applied @ 3.84 kg/10 sqm)
2150.10.1:Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete
2250.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete
2313.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work
2412.50:Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
2512.51.1:Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screwscomplete :Ridges plain (500-600 mm)
2650.9.1.1:Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality Anjili wood /jack wood
2750.9.2.1:Providing and fixing paneled and glazed shutters for doors, windows and clerestory windows, 35 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineerin - charge using Anjili/ Jack wood
289.48.2:Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc
299.63.3:Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barreltype) with necessary screws etc. complete : (Copper oxidized as per IS : 1378)150x10 mm
309.66.1:Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992with necessary screws etc. complete : (Copper oxidized as per IS : 1378).125 mm
3150.9.15.1:Supplying and fixing 200 mm Aluminium aldrop
3250.9.15.4:Providing and fixing iron hooks and eyes: 150 mm
33Retaining wall
342.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil
35OD3521/2026-2027:Modified data of 60.7.1 DRY RUBBLE MASONRY - Dry rubble without concrete levelling course masonry with good quality blasted rubble including packing to compactness to lines and levels cost and conveyance of all materials labour charges etc. complete as per direction of Departmental officers at site.
365.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete
374.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)
385.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more
3950.2.25.1:Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge
4013.33.1:Pointing on stone work with cement mortar 1:3 ( 1 cement : 3 fine sand):Flush/ Ruled pointing Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58458130
AUTHORITY Government Departments
TENDER VALUE 10.57 Lakhs
LAST DATE 24-11-2026
Authority
Authority Name Department Of Agriculture
Work Description Tender for General-Alappuzha District Panchayath 2024-25Ambalappuzha Division- Project No 861/2024-25 Construction Of Motor Thara And Shed In Nanekkad Padasekharam Ward No.7 Ambalappuzha North Grama Panchayath Alappuzha-General Civil Work
Basic Detail
Tender No AE(3)7/2026
Bidding Type Tender
Location
City Alappuzha
State Kerala
Key Dates
Publish Date 09 Nov 2026
Submission Date 24 Nov 2026
Open Date 27 Nov 2026
Finance
Tender Value 10.57 Lakhs
Tender Fee 2760
EMD 26449
Exemption Available
Document List
28755e58-63bc-42d0-acbe-71b9a359dd99.html
AffidavitFormc.pdf
biddocu.pdf
BOQ_1514341.xls
EPAYMENTFORM.pdf
formoftender.pdf
integritypactc.pdf
preliminaryagreement.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 09, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Nov 24, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 3 days
Nov 27, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 6 days

Tender Documents

Download All (ZIP) ↓
html

28755e58-63bc-42d0-acbe-71b9a359dd99.html

pdf

AffidavitFormc.pdf

pdf

biddocu.pdf

xls

BOQ_1514341.xls

pdf

EPAYMENTFORM.pdf

pdf

formoftender.pdf

pdf

integritypactc.pdf

pdf

preliminaryagreement.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender