Bids Are invited for Repair And Overhauling Service - Repair Overhauling Of Deck Machinery Onboard In Ship; Any Other Suitable Brand; Yes; Buyer Premises - Single Arm Boat Davitwhole Single Arm Boat Davitwhole Single Arm Boat Davit: Degutting/ Re-Gut

Sharing tender

Bids Are invited for Repair And Overhauling Service - Repair Overhauling Of Deck Machinery Onboard In Ship; Any Other Suitable Brand; Yes; Buyer Premises - Single Arm Boat Davitwhole Single Arm Boat Davitwhole Single Arm Boat Davit: Degutting/ Re-Gutting Of Entire Davit From/ To Foundation, Separation/ Detachment Arm And Vertical Column, De-Coupling Of Motors And Gear Boxes And Dismantling Of Its Sub-Assemblies. While Re-Gutting The Davit Suitable Ht Bolts May Be Used And Proper Care To Be Taken Whilst Tightening The Davit To The Foundation. , Single Arm Boat Davitwhole Single Arm Boat Davitwhole Single Arm Boat Davit: Hydro Blasting Of Entire Davit Structure And Sub-Assemblies (To Hpps) To Remove Paint And Arrive At Bare Metal Followed By Application Of Primer For Preservation. Survey Davit Structure And Gearboxes For Corrosion, Distortion, Pitting, Holes And Repair As Per Survey Reports. , Single Arm Boat Davitwhole Single Arm Boat Davitwhole Single Arm Boat Davit: Carry Out Repair/ Renewal Of Structure/ Gear Box Housings As Required. In Case Of Repair Of Gearbox Housing, Trueness And Alignment Of Drive And Driven Shaft Also Be Undertaken. , Single Arm Boat Davitwhole Single Arm Boat Davitluffing Gear Box: Dismantling, Defect Identification And Overhauling Of Luffing Gear Box. Which Includes Replacement Of Worn-Out / Damaged Bearings, Screw Shaft, Gears, Pinions, Shafts, Bearing End Covers, Inspection Covers, Bushes, Circlips, Oil Seals, Washers/ Spring Washers/ Thrust Washers, Oil Level Indicators, Oil Drain Plug And Fasteners. Ensure For No Oil Leakage From Gear Box And Its Seals, Any Evidence Of Oil Leakage, Repair Accordingly. Qc To Be Offered Each And Every Stage Such As Dismantling, Defect Identification, New Spares Inspection, Overhauling And Trails (Which Includes Load Trails) , Single Arm Boat Davitwhole Single Arm Boat Davithoisting/Lowering Gear Box And Its Winch: Dismantling, Defect Identification And Overhauling Of Hoisting/Lowering Gear Box And Its Winch. Which Includes Replacement Of Worn-Out / Damaged Bearings, Gears, Pinions, Shafts, Bearing End Covers, Inspection Covers, Bushes, Circlips, Oil Seals, Washers/ Spring Washers/ Thrust Washers, Deadman Weight/Counter Weight, Oil Level Indicators, Oil Drain Plug And Fasteners. Ensure For No Oil Leakage From Gear Box And Its Seals, Any Evidence Of Oil Leakage, Repair Accordingly. Qc To Be Offered Each And Every Stage Such As Dismantling, Defect Identification, New Spares Inspection, Overhauling And Trails (Which Includes Load Trails) , Single Arm Boat Davitwhole Single Arm Boat Davitslewing Arrangement & Slewing Gear Box: Dismantling, Defect Identification And Overhauling Of Slewing Gear Box. Which Includes Replacement Of Worn-Out / Damaged Bearings, Gears, Slewing Ring Gear (If, Installed), Pinions, Shafts, Bearing End Covers, Inspection Covers, Bushes, Circlips, Oil Seals, Cylindrical Rollers, Worm Wheel & Worm Shaft, Washers/ Spring Washers/ Thrust Washers, Oil Level Indicators, Oil Drain Plug And Fasteners. Ensure For No Oil Leakage From Gear Box And Its Seals, Any Evidence Of Oil Leakage, Repair Accordingly. Qc To Be Offered Each And Every Stage Such As Dismantling, Defect Identification, New Spares Inspection, Overhauling And Trails (Which Includes Load Trails) , Single Arm Boat Davitwhole Single Arm Boat Davitclutch Cum Coupling, Centrifugal Brake Unit, Engaging And Dis-Engaging Mechanism & Manual Hand Operation: Dismantling, Defect Identification And Overhauling Of Clutch Cum Coupling, Centrifugal Brake Unit, Engaging And Dis-Engaging Mechanism. Which Includes Replacement/Repair Of Clutch Plates. Qc To Be Offered Before And After Assembly.-01 Each , Single Arm Boat Davitwhole Single Arm Boat Davitcharge Oil In Gear Boxes With Servo Gear Oil 140 Or As Specified In The Oem Manual Or As Provided By The Ss. Charge Grease Into Grease Nipples. Grease All Sheaves, Pivots And Other Moving Parts Of The Davit. , Single Arm Boat Davitwhole Single Arm Boat Davitprove Davit For Load Test As Per Oem Specified Standards For Safe And Running Loads. , Single Arm Boat Davitwhole Single Arm Boat Davitdocument All Activities Undertaken With Time And Spares Consumed And Submit The Same. , Single Arm Boat Davitwhole Single Arm Boat Davitafter Completion Of Load Test, Re-Examine The Complete Davit Structure And Associated Lifting Gears For Flaws, Distortion, Deflection Etc. If, Any Flaws Observed Those Flaws Must Be Examined By Ndt Techniques And Accordingly Carry Out Repairs As Necessary And Re-Offer To Load Testing Like Wise. , Anchor Windlassanchor Windlass Unit (Reducción Gear Box)1.1 Degutting / Re-Gutting Of Entire Anchor Windlass From/To Onboard Ship Together With Foundation Bed. Dismantle, Defect Identification Of Gear Box And All Other Allied Units. Check The Worm Wheel And Worm Shaft And Bull Gear Condition If, Excessive Clearance / Score Marks/Dents/Damages Or Condition Of Gear Tooth Profile Damaged, Renew The Gears As Recommended.1.2 Check The Trueness Of The Shafts. Check For Nicks/ Dents /Corrosion Pit Marks, If Necessary Carryout Metal Build/ Low Thermal Spray As Required To Restore The Original Dimensions.1.3 Overhaul The Gear Box. Renew All Bearings, Seals, Gaskets, Grease Nipples, Oil Level Indicator And Worn-Out Parts Etc. As Necessary. 1.4 Refill The Lube Oil As Provided By Ss As Per Oem Manual/User Department/Ss Instructions As Applicable. , Anchor Windlasscable Lifter (01), Warping Drums (02) And Engaging & Dis-Engaging Unit (01) And Cable Guider (01)2.1 Remove/Reinstall The Cable Lifter And Warping Drum From/To Anchor Windlass. Check Clearances Between The Shaft And Drum, If Found Excessive Renew All Bush Bearings And Worn-Out Parts, Survey To Be Carried Out And Based On Survey Report Repair Works To Be Carried Out Like Metal Build-Up, Grinding/Machining To Attain Desired Surface Finishing. 2.2 Check The Profile Of Cable Lifter And Outer Diameter Of Brake Seating Area, If, Found Defective Introduce Double Plate With Necessary Metal Build-Up By Providing Necessary Counter Boring Holes In Zig Zag Method And Machining, If Worn Out Restore The Original Dimension By Metal Build Up And Grinding/Machining.2.3 Overhaul The Engage/Dis-Engage Units, Repair/Renew The Engage/Dis-Engage Units. If Required. 2.4 Check The Clearance Of Bushes If, Found Not In Order Replace The Same With Suitable Bushes As Recommended.2.5 Further All Allied End Plates/Flanges To Be Repaired Or Renewed And All Fasteners And Grease Nipples To Be Replaced With New One. , Anchor Windlassbrake Band Mechanism3.1 Check/Measure The Thickness Of The Brake Liner, Renew The Same If Excessive Wear And Tear As Required. Renew Hinge Pins Bush Bearings, Washers, Spring Washers And Flat Washers As Required.3.2 Check The Spindle / Shaft, If Any Damage/Worn Out Of Tooth Profile. Repair/ Renew The Spindle / Shaft. , Anchor Windlasshorizontal Shaft (01) And Split Bushes (02 Sets)4.1 Gauge The Horizontal Shaft (01) And Carryout Necessary Metal Build-Up And Machining To Attain The Required Dimensions And Finishing. , Anchor Windlasshorizontal Shaft (01) And Split Bushes (02 Sets)4.2 Split Bushes Gauging To Be Carried Out And Renew/Replace If, Found Any Abnormality Identified And Align Accurately , Anchor Windlassalignmentpost Integration And Re-Fitment Of Windlass, Align The Gear Box With Motor. Maintain The Radial And Axial Alignment Readings As Per Technical Manual. Alignment Of Horizontal Shaft Together With Journal Bearings Also To Be Carried Out For Its Smooth And Effective Operation , Anchor Windlassslipping Clutch Cum Coupling/Bsd Omega Elastomer Couplingdegutting/Re-Gutting, Dismantling, Defect Identification And Overhaul Of Clutch Coupling, If The Clutch Damaged And Beyond Economical Repairs, Replace With New One , Anchor Windlassfoundation/ Intermediate Bedcheck The Condition Of Foundation Strength And Survey And Repair The Same, Replace All Fasteners With Ht Bolts & Nuts Together With Washers, Spring Washers And Washers As Required , Anchor Windlasstrials And Stwpost Integration And Re-Fitment Onboard, Trials And Stw To Be Undertaken By The Firm In Harbour To Satisfactory Performance Iaw. Naval Requirements/Naval Testing Agencies. , Electric Aft Mooring Capstanaft Mooring Capstan Unit/ Cycloid Type Gear Box1.1 Degutting/Re-Gutting Of Aft Mooring Capstan From/To Onboard Ship.1.2 Check/Inspect The Condition Of Deck Mounted Bed /Foundation Bed And Repair Or Replace As Necessary.1.3 Capstan External Body To Be Cleaned Thoroughly By The Way Of Hydro Blasting And Carryout Of Survey If, Required (Or) As Recommended By Department And Carryout Repairs By Way Of Metal Build-Up As Necessary And Grinding / Machining May Be Undertaken As Necessary As Per Survey Report.1.4 Dismantle The Cycloid Type Gear Box And Carry Out The Defect Identification And Check The Condition Of Gear Tooth Profile, If, Tooth Profile Damaged Or Found Excessive Wear And Tear, Renew The Gears As Recommended And Check Trueness Of The Shafts. Check For Nicks/ Dents /Corrosion Pit Marks, If Necessary Carryout Metal Build/ Low Thermal Spray As Required To Restore The Original Dimensions.1.5 Overhaul The Cycloid Type Gear Box. Renew All Bearings, Seals, O Rings, Eccentric, Gears, Pins, Rollers, Ring Gear, Gaskets, Grease Nipples, Oil Level Indicator And Worn-Out Parts Etc.. Necessary Precautions To Be Taken While Overhaul The Cycloid Type Gear Box And Make Sure That It Should Freely Rotate In Both The Directions And Further Ensure No Lube Oil Leakage From The Gear Box.1.6 Refill The Lube Oil As Provided By Ss As Per Oem Manual/User Department/Ss Instructions As Applicable. , Electric Aft Mooring Capstanwarping Drums (01) 2.1 Remove/Reinstall The Warping Drums From/To Aft Mooring Capstan. Check Clearances Between The Shaft And Drum, Check The Surface Area If, Dents And Pit Holes Are Observed Undertake With Necessary Metal Build-Up And Machining/Grinding, To Restore The Original Dimension.2.2 Check The Clearance Of Bushes If, Found Not In Order Replace The Same With Suitable Bushes As Recommended. , Electric Aft Mooring Capstandecoupling & Recoupling Of Motor & Gear Boxpost Integration And Re-Fitment Of Capstan, Fit The Gear Box With Motor. , Electric Aft Mooring Capstanfoundation/ Intermediate Bedcheck The Condition Of Intermediate Bed /Foundation Bed Strength And Survey And Repair The Same, Replace All Fasteners With Ht Bolts & Nuts Together With Washers, Spring Washers , Electric Aft Mooring Capstantrials And Stwpost Integration And Re-Fitment Onboard, Trials And Stw To Be Undertaken By The Firm In Harbour To Satisfactory Performance Iaw. Naval Requirements/Naval Testing Agencies (Hitu). , Electric Aft Mooring Capstanaccommodation Ladder Winch Gear Box.1.1 Degutting Of Entire Unit And Shift To Respective Shop Floor-01 Unit , Electric Aft Mooring Capstanaccommodation Ladder Winch Gear Box.1.2 Decoupling Of Coupling Of Gear Box And Motor And Degutting Of Electric Motor. If Coupling Defective Or Damaged Replace With New One. , Electric Aft Mooring Capstanaccommodation Ladder Winch Gear Box.1.3 Hydro Blasting Of Entire Unit And Intermediate Bed/Foundation. Apply Primer On The External Surfaces Of The Equipment Post Completion Of Hydro Blasting.-01 Unit , Electric Aft Mooring Capstanaccommodation Ladder Winch Gear Box.1.4 Structural Survey Of Intermediate Foundation/Bed And Other Structural Parts As Necessary As Instructed By The User Department-01 Unit , Electric Aft Mooring Capstanaccommodation Ladder Winch Gear Box.1.5 Dismantling, Defect Identification Of Gear Box, Preparation Of List Of Spares, Offer To Qc For Inspection Of Spares And Overhaul The Gear Box. Replace All Bearings, Cup Seals, Grease Nipples, Oil Level Indicators And Oil Drain Plug With New One. If, The Gears Are Found Excessive Wear And Tear And Dents/Damages In The Gear Tooth Profile, Replace Them With New Ones. Proper Care Must Be Taken While Overhaul The Gear Box As The Gear Box Should Rotate Freely When Rotate By Hand. Blue/Red Impression Of Gears Must Be Checked And The Gear Meshing Should Be Greater Than That Of 40% , Electric Aft Mooring Capstanaccommodation Ladder Winch Gear Box.1.6 Rope Reel Drums Shall Be Degutted From Its Shaft And Clean And Inspect For Any Evidence Of Dents, Cracks, Metal Thin Due To Corrosion Be Addressed By Of Metal Build-Up/Low Thermal Spray/ Machining, Keys, Key Ways And Locking Mechanism , Electric Aft Mooring Capstanaccommodation Ladder Winch Gear Box.1.7 Repair Of Intermediate Foundation / Bed And Other Structural Parts As Per Survey Report , Electric Aft Mooring Capstanaccommodation Ladder Winch Gear Box.1.8 All Parts Are To Be Integrated As Earlier And Necessary Care To Be Taken While Align The Motor And Gear Box Is Undertaken And Post Alignment The Gear Box Should Error Free. All Fasteners Such As Bolts, Nuts, Spring Washers, Flat Washers Should Be Of Ht Or Equivalent To The Naval Standards-01 Set & As Necessary , Electric Aft Mooring Capstanaccommodation Ladder Winch Gear Box.1.9 Shifting Of Entire Accommodation Ladder Winch Gear Box Unit On-Board, Onboard Fitment Of Equipment. Fill The Recommended Lube Oil In The Gear Boxes As Provided By The Ss And Maintain Appropriate Levels, Arrest The Oil Leakages If, Found.-01 Unit , Electric Aft Mooring Capstanaccommodation Ladder Winch Gear Box.1.10 Ideal Trails To Be Taken In Both Manual And Electric Mode And Post Completion Of Ideal Trails Trials To Be Carried Out Up To Hitu Team Certification Standards. Further, All Hitu (Or) Any Other Inspection Agencies Remarks/Observations To Be Liquidated As Per Standards-01 Unit , Mandatory Spares,Oil Plug,Part No - 1.28002B1 , Mandatory Spares,Grease Nipples 1/4Th Bsp Or As Per Sample,Part No - 2.28002Ag , Mandatory Spares,Grease Nipples 1/8Th Bsp Or As Per Sample,Part No - 2.28002Af , Mandatory Spares,Hand Wheel,Part No - 2.2800105 , Mandatory Spares,Hand Wheel,Part No - 1.2800216 , Mandatory Spares,Pinion Shaft,Part No - 1.2800206 , Mandatory Spares,Split Pins 04 Mm (Length 85Mm),Part No - 1.336 , Mandatory Spares,Split Pins 05 Mm (Length 85Mm),Part No - 1.587965 , Mandatory Spares,22 Mm Ht Hex Bolt + Nut+ Sp. Washer,Part No - 1.45872 , Mandatory Spares,Brake Band Collar Pins (As Per Sample),Part No - 1.55789 , Mandatory Spares,Oil Level Indicator (As Per Sample),Part No - 1.22685 , Mandatory Spares,18 Mm Hex Bolt + Sp. Washer,Part No - 1.3354 , Mandatory Spares,16 Hex Bolt + Sp. Washer,Part No - 1.11287 , Mandatory Spares,Cable Drum Holder Bush Bearing (As Per Sample),Part No - 1.22497 , Mandatory Spares,24 Mm Ht Hex Bolt + Sp. Washer,Part No - 1.85674 , Mandatory Spares,08 Mm Ss Counter Sunk Screws,Part No - 1.5914 , Mandatory Spares,10 Mm Ss Counter Sunk Screws,Part No - 1.321 , Mandatory Spares,12 Mm Ss Counter Sunk Screws,Part No - 1.8779 , Mandatory Spares,M12 Studs,Part No - 1.9347 , Mandatory Spares,M16 Studs,Part No - 1.338 , Mandatory Spares,Spindle/Shaft (As Per Sample),Part No - 1.682 , Mandatory Spares,Coupling Guard For Slipping Clutch Cum Coupling),Part No - 1.44778 , Mandatory Spares,Brake Band Pins (As Per Sample),Part No - 1.3428 , Mandatory Spares,22 Mm Ht Hex Bolt + Nut+ Sp. Washer,Part No - 1.652487 , Mandatory Spares,Casing ,Part No - 196019 , Mandatory Spares,Snap Ring (6216 Nr) ,Part No - 315043 , Mandatory Spares,Output Cover,Part No - 106127 , Mandatory Spares,Hex Screw M8 X 30 ,Part No - 300044 , Mandatory Spares,Key 08-07-042,Part No - 312011 , Mandatory Spares,Motor Flange - 132,Part No - 196379 , Mandatory Spares,Input Cover ,Part No - 106142 , Mandatory Spares,Hex. Nut M16 X 1.5,Part No - 303360 , Mandatory Spares,Key 18-11-120,Part No - 312236 , Mandatory Spares,Hex. Nut M12 X 35,Part No - 300009 , Mandatory Spares,½ Socket Flange Plug (Flow) ,Part No - 306004 , Mandatory Spares,½ Bsp Breather Plug (Flow) ,Part No - 306008 , Mandatory Spares,¼ Socket Flange Plug (Flow) ,Part No - 306003 , Mandatory Spares,Pinion Shaft,Part No - 11.87 , Mandatory Spares,Gear Wheel,Part No - 11.88 , Mandatory Spares,Ball Bearing,Part No - 11.91 , Mandatory Spares,Ball Bearing,Part No - 11.92 , Mandatory Spares,Hexa Bolt + Sp Washer,Part No - 11.95 , Mandatory Spares,Hexa Bolt + Sp Washer,Part No - 11.98 , Mandatory Spares,Gear Wheel,Part No - 11.99 , Mandatory Spares,Main Shaft,Part No - 11.101 , Mandatory Spares,Ball Bearing,Part No - 11.103 , Mandatory Spares,Hexa Bolt + Sp Washer,Part No - 11.106 , Mandatory Spares,Oil Seal,Part No - 11.107 , Mandatory Spares,Hexa Bolt + Sp Washer,Part No - 11.11 , Mandatory Spares,Rope Clamp,Part No - 11.113 , Mandatory Spares,Align Bolt + Sp Washer,Part No - 11.114 , Mandatory Spares,Shaft,Part No - 13.4 , Mandatory Spares,Shaft,Part No - 10.1 , Mandatory Spares,Oil Seal,Part No - 7.23 , Mandatory Spares,Worm Shaft,Part No - 7.24 , Mandatory Spares,Bearing,Part No - 7.25 , Mandatory Spares,Grease Nipple,Part No - 10.12 , Mandatory Spares,Hexa Bolt + Sp Washer,Part No - 11.02 , Mandatory Spares,Coupling,Part No - 11.04 , Mandatory Spares,Motor Mounting False Plate,Part No - 11.05 , Mandatory Spares,Hexa Bolt + Sp Washer + Nut,Part No - 11.09 , Mandatory Spares,Hexa Bolt + Sp Washer,Part No - 11.12 , Mandatory Spares,Oil Level Indicator,Part No - 11.14 , Mandatory Spares,Drain Plug,Part No - 11.15 , Mandatory Spares,Pinion Helical,Part No - 11.16 , Mandatory Spares,Hexa Bolt + Sp Washer,Part No - 11.18 , Mandatory Spares,Gear Wheel Helical,Part No - 11.19 , Mandatory Spares,Ball Bearing ,Part No - 11.2 , Mandatory Spares,Csk Hex Socket Screw,Part No - 11.25 , Mandatory Spares,Ball Bearing,Part No - 11.26 , Mandatory Spares,Multi Disc Clutch,Part No - 11.28 , Mandatory Spares,Hex Bolt + Sp Washer,Part No - 11.29 , Mandatory Spares,Hex Bolt + Sp Washer + Nut,Part No - 11.32 , Mandatory Spares,Hex Bolt + Sp Washer + Nut,Part No - 11.34 , Mandatory Spares,Split Pin,Part No - 11.35 , Mandatory Spares,Clutch Shifter Shaft,Part No - 11.36 , Mandatory Spares,Bush Bearing,Part No - 11.37 , Mandatory Spares,Packing,Part No - 11.38 , Mandatory Spares,Hex Bolt + Sp Washer,Part No - 11.39 , Mandatory Spares,Oil Seal,Part No - 11.4 , Mandatory Spares,Hex Bolt + Sp Washer,Part No - 11.42 , Mandatory Spares,Bush Bearing,Part No - 11.46 , Mandatory Spares,Pinion Shaft,Part No - 11.48 , Mandatory Spares,Grease Nipple,Part No - 11.49 , Mandatory Spares,Packing ,Part No - 11.51 , Mandatory Spares,Oil Seals,Part No - 11.53 , Mandatory Spares,Ball Bearing - 2 Rs,Part No - 11.54 , Mandatory Spares,O Ring,Part No - 11.55 , Mandatory Spares,Brake Disc ,Part No - 11.56 , Mandatory Spares,Circlip External,Part No - 11.58 , Mandatory Spares,Lining,Part No - 11.64 , Mandatory Spares,Rivit,Part No - 11.65 , Mandatory Spares,Spring,Part No - 11.66 , Mandatory Spares,Acentric,Part No - 11.67 , Mandatory Spares,Oil Seal,Part No - 11.68 , Mandatory Spares,Internal Circlip,Part No - 11.69 , Mandatory Spares,O Ring,Part No - 11.7 , Mandatory Spares,Washer,Part No - 11.71 , Mandatory Spares,Cover,Part No - 11.72 , Mandatory Spares,Packing,Part No - 11.73 , Mandatory Spares,Hex Bolt + Sp Washer,Part No - 11.74 , Mandatory Spares,Bush Bearing,Part No - 11.75 , Mandatory Spares,Grub Screw,Part No - 11.76 , Mandatory Spares,Brake Shoe,Part No - 11.78 , Mandatory Spares,Uning,Part No - 11.79 , Mandatory Spares,Rivit,Part No - 11.8 , Mandatory Spares,Hex Bolt + Sp Washer,Part No - 3.02 , Mandatory Spares,Coupling,Part No - 3.04 , Mandatory Spares,Hex Bolt + Sp Washer + Nut,Part No - 3.06 , Mandatory Spares,Hex Bolt + Sp Washer,Part No - 3.09 , Mandatory Spares,Hex Bolt + Sp Washer,Part No - 3.12 , Mandatory Spares,Oil Seal,Part No - 3.13 , Mandatory Spares,Oil Level Indicator,Part No - 3.15 , Mandatory Spares,Drain Plug,Part No - 3.16 , Mandatory Spares,Worm Shaft,Part No - 3.17 , Mandatory Spares,Tapper Roller Bearing,Part No - 3.19 , Mandatory Spares,Bearing Housing,Part No - 3.2 , Mandatory Spares,Hex Bolt + Sp Washer,Part No - 3.26 , Mandatory Spares,Oil Seal,Part No - 3.3 , Mandatory Spares,Worm Wheel,Part No - 3.31 , Mandatory Spares,Hex Bolt + Sp Washer,Part No - 3.38 , Mandatory Spares,Hex Bolt + Sp Washer,Part No - 3.41 , Mandatory Spares,Worm Wheel,Part No - 3.42.1 , Mandatory Spares,Worm Wheel Boss,Part No - 3.42.2 , Mandatory Spares,Ball Bearing,Part No - 3.44 , Mandatory Spares,Hex Bolt + Sp Washer,Part No - 3.47 , Mandatory Spares,Main Shaft,Part No - 3.48 , Mandatory Spares,Pinion,Part No - 3.5 , Mandatory Spares,Alen Head Csk Bolt,Part No - 3.53 , Mandatory Spares,Hex Bolt + Sp Washer,Part No - 3.56 , Mandatory Spares,Oil Seal ,Part No - 7.02 , Mandatory Spares,Bearing,Part No - 7.5 , Mandatory Spares,Worm Wheel Boss,Part No - 7.6 , Mandatory Spares,Worm Wheel,Part No - 7.7 , Mandatory Spares,Grub Screw,Part No - 7.8 , Mandatory Spares,Thrust Bearing,Part No - 7.9 , Mandatory Spares,Bolt,Part No - 7.1 , Mandatory Spares,Washer,Part No - 7.11 , Mandatory Spares,Nut,Part No - 7.12 , Mandatory Spares,Forged Bolts,Part No - 7.14 , Mandatory Spares,En Bolts,Part No - 7.16 , Mandatory Spares,Bolts,Part No - 7.18 , Mandatory Spares,Packing,Part No - 7.19 , Mandatory Spares,Shafting Helical Bolts,Part No - 7.2 , Mandatory Spares,Bearing For Worm Shaft ,Part No - 7.223 , Mandatory Spares,Ball Bearing For Worm Wheel,Part No - 7.012 , Mandatory Spares,Grease Nipples (I/8Th Bsp),Part No - 7.003 , Mandatory Spares,Pulleys (As Per Sample),Part No - 7.315 , Mandatory Spares,Cup Seals ,Part No - 7.002 , Mandatory Spares,Cup Seals ,Part No - 7.007 , Mandatory Spares,Oil Level Indicator (As Per Sample),Part No - 7.52 , Mandatory Spares,Oil Drain Plug (As Per Sample),Part No - 7.00E+03 , Mandatory Spares,Worm Wheel (As Per Sample),Part No - 7.F4 , Mandatory Spares,Worm Shaft (As Per Sample),Part No - 8.12 , Mandatory Spares,Bearing End Cover,Part No - 8.13 , Mandatory Spares,Shims (As Per Sample),Part No - 8.002 , Mandatory Spares,Coupling (As Per Sample),Part No - 8.006 , Mandatory Spares,M20 Ht Bolts, Nut, Spring Washer & Flat Washer,Part No - 8.009 , Mandatory Spares,M18 Ht Bolts, Nut, Spring Washer & Flat Washer,Part No - 8.101