Power Government Departments Closing in 1 days TDR #58448827

Tender For E-Tender For Annual Maintenance Of 30 Mw Unit-1 At 2X30 Mw Giri Power House, Giri Nagar.

Issued by Government Departments · Sirmaur, Himachal Pradesh
Tender Value
Ref. Documents
Estimated cost
Bid Submission
19 Nov 2026
1 days left
EMD
29820
Bank guarantee accepted
Document Fee
1180
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Sirmaur → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available

Project Description

Tender for E-Tender For Annual Maintenance Of 30 Mw Unit-1 At 2X30 Mw Giri Power House, Giri Nagar.

BOQ

Name of Work:- E-Tender for Annual Maintenance of 30 MW Unit-1 at 2x30 MW Giri Power House, Giri Nagar.
Sl. No. Item Description
1Dismantling of under water parts of machine i.e.adjusting rings (4 pcs), lower DT cone, upper DT cone,, runner cone, runner, pivot ring, giude vanes (16 Nos), straps, levers, turn buckles, end plates, bearing bodies (16 Nos.), regulating ring, etc. and proper stacking of dismantled items in consultation with Site Engineer
2Dismantling of shaft sealing ring (2 pcs) , Sealing body (4 Pcs) , TGB tank etc. and proper stacking of dismantled items in consultation with site engineer in service bay
3Repair of shaft sealing ring (2 Pcs) by welding with SS MO-309 welding electrodes throughout the periphery to meet the decreased dimensions and then machining and polishing of the same to match the original profile as per BHEL drawing at contractor workshop including transportation charges.
4Assembling of shaft sealing body, sealing ring, TGB tank, etc. complete in all respects including testing and commissioning. (All necessary materials used for assembling like gaskets, permanent sheets, neoprene sheets, nut bolts, welding rods, cup seals etc shall be arranged by contractor).
5Dismantling of thrust coolers (8 Nos), UGB coolers (8 Nos), UGB inspection windows, LGB coolers (8 Nos), TGB coolers (1 No.), stator air coolers (8 Nos), related cooling pipelines. Thorough cleaning of turbine and OPU tanks. Flushing and cleaning the above mentioned coolers by water jet. Inspecting/checking any damaged cupronickel tubes with pressure gun (4 Kg/cm2). After inspection / checking re-assembling coolers assembly by providing and fixing new permanent sheets, rubber sheets and nut & bolts. Coolers to be painted from outside with smoke grey paint and with epoxy paint from inside. Refitting the above coolers in their position after cleaning and testing. Coolers found defective shall replaced with new one (Spare coolers for replacement shall be provided by HPSEBL)
6Repair/Resize of hole of 8 Nos of Thrust, 8 Nos of LGB & 8 Nos of UGB cooler by suitable welding of damaged holes of flangs and drilling, threading and reaming/machining of hole to the required original bolt size by removing the fixed flang and after threading Fixing & welding the flangs in its original position also Providing and fixing of 100 kg of SS 304 Grade Nut & Botls (different size, as per sample) for the Thrust, LGB,UGB cooler complete job in all respect as per the best satisfaction of Engineer in charge. (all consumable items are in contractor scope)
7Dismantling of Thrust, LGB, UGB, TGB pads, supporting discs. DPT and UT test of thrust, UGB, LGB, TGB (testing kits / UT arrangement to be arranged by contractor). Defective pads for replacement will be provided by HPSEBL during assembly. Blue matching of TGB, UGB, LGB w.r.t respective journals. Blue matching of thrust pads with mirror disc. Assembling of UGB, LGB, TGB pads and setting their respective clearances as per OEM standards by BHEL/Ex BHEL experts. (Necessary shims to be arranged by contractor)
8Repair of PRV by dismantling of parts and replacement of O-rings, seals, gaskets etc. as per BHEL drawing by welding, grinding, matching etc. to the pitted portion of disc and cylinder to match the original profile as per BHEL drawing including testing and commissioning complete in all respects.
9Assembling of underwater parts like pivot ring, guide vanes (16Nos), bearing bodies (16Nos), bushes, straps, levers, turnbuckles, runner bolts, runner, runner cone, upper and lower DT cone, adjusting rings, etc. (all necessary material used for assembling like gaskets, O-rings, permanent sheets, neoprene sheets, nut bolts, welding rods, upper and lower cup seals etc. shall be arranged by contractor) complete in all respects
10Complete overhauling of spherical bypass valve i.e. dismantling of assembly from penstock and dismantling of bushes & spindle from assembly etc. Replacement of rubber cord 8.0 mm, steel meshes rubber sheet 3.0 mm (champion make), glands - 8.0 mm, H.T. nut & bolts (22x55 mm) - 12 Nos., H.T. studs (22x120 mm) - 12 Nos., welding & grinding of pitted portion. Manufacturing / fabrication of SS ring & bushes as per OD of spindle and as per Drg. No.56131000. Then fitting of bushes in assembly and blue matching of spindle with SS ring. Re-assembly and refitting of Bypass valve including testing, successful commissioning, transportation and insurance charges as per satisfaction of Engineer-in-charge (complete job in all respect)
11Repair of damaged / defective Air release valve of MIV by dismantling of air release assembly and then welding, grinding and then re-assembling the same including replacement of gasket, o-rings, studs complete job in all respects as per satisfaction of Engineer-In-Charge.
12Scraping of old paint/rust using scrapers/emery paper, cleaning and preparation of surfaces to remove dirt, grease, oil and other foreign matter, followed by application of one coat of suitable primer and two coats of synthetic enamel paint/ Oil paint on the exterior surfaces of spiral casing (inside Power House), draft tube, pressure relief valve, 02 Nos. servomotors, bypass valve, 02 Nos. journals, penstock drain valve, oil pipes, water pipes, air pipes, governor tank, spherical tank, TGB tank, UGB tank, LGB tank, visible parts of Generator No. 1 including thrust tank, pilot and main exciter outer body, stairs and other associated surfaces, as per approved colour scheme, complete in all respects to the satisfaction of the Engineer-in-Charge.
13Preparing the surface by throughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete outer and inner-surface of spiral casing and draft tube segment of unit-1 by hand-scrapping, to make surface even and suitable for coating Providing and applying of Stanvac make 1040 Stangard surface tolerant (long life impermeable barrier epoxy for excellent adhesion on wet surface) and then applying the coating of 725 PUTC on the surface of spiral casing, draft tube complete in all respects as per the entire satisfaction of Engineer-in-Charge
14Minor repair of stay vanes, regulating ring of servo motor shaft (opening side) by welding, grinding to stop oil leakage and matching as per drawing, cleaning of tracks on which regulating ring move, cleaning of rusted surfaces of regulating ring assembly of all grease, dirt, dust and foreign material by scrapping and complete removal of mud, after cleaning applying grease on regulating ring track, two coats with zinc rich primer and finally painting with two coats of Epilux 4-5 complete in all respects to the entire satisfaction of Engineer-in-Charge.
15Levelling, Centering, alignment (complete throw) of Unit-1 so that parameters of machine should come within permissible limit as per OEM standard, complete alignment of machine and the same process shall be repeated for exciter alignment as per direction of BHEL/Ex-BHEL expert and as per entire satisfaction of Engineer-in-Charge
16Overhauling / Maintenance of HMC of Governor of Unit No.I of Giri Power House BHEL make as per Sr.No.7508392 by servicing of its control panels as per operational requirement by BHEL / Ex-BHEL expert complete in all repsect as per the direction of Engineer-in-charge.
17Tightening of steel rope between regulating ring and master controller at zero servo motor setting, tightening of steel rope between master controller and EHT cabinet, tuning of Governor by adjusting tie rod and bolt for gap adjustment and adjustment of limiter cam shaft, adjustment of OLG motor cam shaft, feedback signal speed setting, gate setting and setting other parameters as per operational requirement by BHEL / Ex-BHEL expert complete in all respect of Unit No.1
18Vibration analysis and balancing of machine as per OEM norms including assistance in spinning, dry out of machine and synchronization of unit No.I of Giri Power House Girinagar Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58448827
AUTHORITY Government Departments
TENDER VALUE Ref. Documents
LAST DATE 19-11-2026
Authority
Authority Name Himachal Pradesh State Electricity Board
Work Description Tender for E-Tender For Annual Maintenance Of 30 Mw Unit-1 At 2X30 Mw Giri Power House, Giri Nagar.
Basic Detail
Tender No HPSEBL/SBD/SEGN/ 2026-27/12
Bidding Type Tender
Location
City Sirmaur
State Himachal Pradesh
Key Dates
Publish Date 09 Nov 2026
Submission Date 19 Nov 2026
Open Date 19 Nov 2026
Finance
Tender Value Ref. Documents
Tender Fee 1180
EMD 29820
Exemption Not Available
Document List
BOQ_220325.xls
de05031d-44d0-41d7-b17c-ff4067a32782.html
SBDbid12.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 09, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Nov 19, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 1 day
Nov 19, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 1 day

Tender Documents

Download All (ZIP) ↓
xls

BOQ_220325.xls

html

de05031d-44d0-41d7-b17c-ff4067a32782.html

pdf

SBDbid12.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender