Tender For Special Repairs To Main Junction Of Road At D Gate, Bayonet Chowk And Other Junction Within Area Of 58 Gtc Happy Valley At Shillong Under Ge Shillong.
Tender Value
55 Lakhs
Estimated cost
Bid Submission
28 Nov 2026
6 days left
EMD
1.07 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
East Khasi Hills → Meghalaya
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repairs To Main Junction Of Road At D Gate, Bayonet Chowk And Other Junction Within Area Of 58 Gtc Happy Valley At Shillong Under Ge Shillong.
BOQ
| Sl. No. | Item Description |
| 1 | M&L Repair to potholes any depth, not exceeding 1 sqm each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc., cutting around edges to at least 25 mm in depth, making good by applying tack coat at the rate of 5 kg per 10 Sqm, putting in bituminous macadam well rammed (including supply of bituminious carpet, binder and chhipping) and sealed with bitumen 9.8 kg per 10 sqm blinded with 0.09 cum stone chippings, 6.3 mm size depth of pot holes exc 30mm and rolled and compacted with power roller 8 to 12 tonnes to required camber and gradient complete all as specified and as directed. |
| 2 | Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area exceeding 400 sqm, depth of pot hole exceeding 50 mm but not exceeding 100 mm including rolling over the broken surfaces using 8 to 10 tonnes power roller to required camber and gradient complete all as specified and as directed. |
| 3 | M&L for Laying and compacting for 150 mm thick (compacted thickness) WMM laid in two layers of 75 mm Wet Mix Macadam (WMM) grading as per table 400-13 of MaRTH specifications for Road and Bridge works 2013 manufactured in WMM plant material comprising of clean, crushed, graded aggregate and granular material premixed with water to a dense mass, spreading with sensor paver and rolling with vibratory roller of capacity 80-100 KN static weight and consolidating to required gradient and camber complete all as specified and directed The finished surface tolerances to be as per Table 900-1 of MaRTH specifications for Road and Bridge works 2013 complete all as specified and directed. |
| 4 | Material and labour for preparing of un-surfaced WBM/ WMM by brushing with wire brushes for removing caked mud etc sweeping with brooms and cleaning complete surfaces by applying mechnical air blower upto entire complete all as specified and as directed. and applying a prime coat of Catonic bitumen emulsion RS1 conforming to IS 8887 at a rate of application of 0.7-1 kg/Sqm on surface of WBM as specified in table 500-3 of MoRTH specification for Road and bridge work 2013 using mechanical sprayer complete all as specified and directed. |
| 5 | Preparing existing black top surfaces by brushing with wire brushes for removing caked mud etc., sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc. complete all as specified and as directed. |
| 6 | Material and labour for providing premixed bituminous macadam laid/rolled and compacted to required gradient and camber using 8 to 10 tone capacity power roller (consolidated thickness 75mm or less) using paving bitumen (VG 30 Grade) @ 4% by weight of total mix complete all as specified and directed. Note:- (i) The exact bitumen content required shall be determined Mix Design procedure and approved by GE. The adjustment in rate on MINUS side variation in quantity of bitumen if any shall be priced at the rate of ₹95 per kg. No claim whatsoever shall be made for adjustment in plus side. (ii) Bituminous macadam shall be laid using self propelled hydrostatic paver finisher and preparation of mix shall be using hot mix plant and transporting the mix in tipper. |
| 7 | M&L for applying a tack coat of cationic bitumen emulsion (RS1) conforming to IS: 8887 at a rate of application of 0.20- 0.30kg/ sqm on bituminious surface as specified in Table- 500-3 of MoRTH specifications for road and bridge work 2013, using mechanical sprayer after cleaning of existing surface complete all as specified and directed . |
| 8 | Material and labour for bituminous premixed semi-dense asphaltic concrete, 40mm consolidated thickness using 5.5% paving bitumen (VG 30 Grade) binder content any penetration by weight of total mix, mixed in central computerized hot mix plant and laid using mechanical self propelled paver and rolled and compacted with 8 to 12 tonne power roller to uniform surfaces with required camber and gradient complete all as specified and as directed.Note:- Semi dense asphaltic bituminous concrete shall be designed as per design mix. Contractor shall quote his unit rate considering the bitumen contents as 5.5 %. Any variation in binder content on minus side shall be adjusted at the rate of ₹95.00 per KG of binder. No adjustment in price shall be made if the variation is on plus side. (Shillong & Umroi) \\" |
| 9 | Providing and laying at or near ground level factory made kerb stone of any size, top bullnosed shape, made of M-25 (Design Mix) grade cement concrete, in position to the required line, level and curvature jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and as directed. |
| 10 | Demolition of cement concrete(unreinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level) and complete all as specified and as directed. |
| 11 | M&L for cement concrete M7.5 (Nominal Mix) using 40 mm nominal size graded crushed stone aggregate 100 mm thick in sub base for laying tiles, pavings, floorings etc. all as specified and as directed. |
| 12 | Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and as directed. |
| 13 | M&L for precast cement concrete solid block masonry of grade C(5.0) with concrete M 10 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate exceeding 10 cm in width and set in cement mortar (1:6) including demolition of old masonry and removal of debries out side of MOD land complete all as specified and as directed. |
| 14 | Material and labour for plastering 15 mm thick on fair faces of brick work or concrete surfaces (on vertical surfaces) in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and as directed. |
| 15 | M&L for cement concrete in surface channels and drains in M10(Nominal Mix) using 40 mm nominal size graded crushed stone aggregate complete all as specified and as directed. |
| 16 | M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc. complete all as specified and as directed. |
| 17 | Demolition of reinforced cement concrete of any description (reinforcement cut as required to facilitate demolition) and in any position, above or below ground floors, not otherwise specifically provided for complete all as specified and as directed. |
| 18 | M&L for RCC M25 (Design Mix) using 20 mm nominal size graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. |
| 19 | M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips and including welding has to be done with minimum 20 cm over lap for new and old of any height complete all as specified and as directed. |
| 20 | M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete complete all as specified and as directed. |
| 21 | S&F in repair traffic convex mirror of of 80cm dia having 130 degree viewing angle made of polycarbonate material , brim and back holding plate is made of metal/FRB along with pole mounted brackets and pole 60mm dia, min height 1.5m made with galvanised steel pipe (medium grade) duly painted with two coats of synthetic enamel paint over a coat of red oxide primer fixed to the ground by means of PCC 1:2:4 type B2 (using 40mm dia graded stone aggregate) in foundation/filling (size 50cmx50cmx60cm) all as specified and as and as directed. |
| 22 | Providing and applying 2.5 mm thick road marking strips (retro-reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi-automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T & P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete all as specified and as directed. |
| 23 | Supply and fixing in repair solar cat eye aluminum alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/ 0.3 watt one NI-ed rechargeable battery (1.2V/ 1600MA) consisting of super bright LED with 10,000 to 18,000 mcd, 3 pieces each side and total 6 pieces are used for high brightness and backup for 12 hours completed as per manufactures instructions etc complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 07, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysNov 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender