Tender For Special Repair Of Block Of Building No P-242 (Single Offrs Accn) At Mil Stn Abohar
Tender Value
38.82 Lakhs
Estimated cost
Bid Submission
21 Nov 2026
0 days left
EMD
77700
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Fazilka → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair Of Block Of Building No P-242 (Single Offrs Accn) At Mil Stn Abohar
BOQ
| Sl. No. | Item Description |
| 1 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and as directed by Engineer-in- charge. |
| 2 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4 Sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and as directed by Engineer-in- charge. |
| 3 | Supply & fixing factory made UPVC window or ventilator side hung/top hung (glazed and gauge both) made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm) including all fittings like hinges, tower blot, peg stay, locking arrangement etc., making arrangement for fixing of hardware all as per manufacture instruction and refer Drg No BTD-890/R complete all as specified and directed.Note : The unit rate quoted by contractor includes cost of glass & wire mesh (4 mm thick sheet glass ordinary quality plain/tinted for window and 4mm thick figured glass pin head type for ventilator, wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm) and includes all other connected accessories. Net Opening will be measured for payment purpose.. Provision of all other items as shown on Drgs & Cutting holes of suitable depth in wall for inserting lugs etc including making good dismantled portion with PCC (1:2:4) type B-0 using 12.5mm graded crushed stone aggregate and cement mortar (1:3) shall be demand to be include. |
| 4 | Supply & fixing aluminium Powder coated grill of approved design/pattern, with approved standard section and fixed to the window frames with CP brass/stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and as directed by Engineer-in-Charge.Note :- The weight of grill shall be physically ascertained through a board of officers convened by CWE and payment shall be made only after the actual weight at site. |
| 5 | Supply & fixing factory made UPVC sliding window three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm) with or without provision of opening for cooler as directed including all fittings, steel roller system, locking arrangement etc., making arrangement for fixing of hardware, glass, wiremesh, grill etc all as per manufacture instruction and Drg No BTD-890/R and as directed.Note : The unit rate quoted by contractor includes cost of glass & wire mesh (5.5mm thick sheet glass ordinary quality & Stainless steel 304 Grade, natural finish, wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm) and includes all other connected accessories. Net Opening will be measured for payment purpose. Provision of all other items as shown on Drgs & Cutting holes of suitable depth in wall for inserting lugs etc including making good dismantled portion with PCC (1:2:4) type B-0 using 12.5mm graded crushed stone aggregate and cement mortar (1:3) shall be demand to be include. |
| 6 | Supply and fixing Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: (i) WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.(ii) Cost for M.S. hold fast/ lugs or SS dash fasteners shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. |
| 7 | Supply and fixing Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: (i) WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.(ii) Cost for M.S. hold fast/ lugs or SS dash fasteners shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. |
| 8 | Supply and fixing Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 150 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: (i) WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.(ii) Cost for M.S. hold fast/ lugs or SS dash fasteners shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. |
| 9 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge including supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 100mm - 4 nos. per leaf (b) Stainless Steel (304 Grade) Finished Square Tower Bolt 150 mm long - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 150 mm - 2 nos. per leaf(d) Stainless Steel (304 Grade) Finished Sliding Bolt 300 mm - 1 no. per leaf |
| 10 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type glazed/gauge skelton door shutter of size 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with butt hinges with necessary full body threaded star headed counter sunk S.S screws including S&F wire cloth complete all as per direction of Engineer- In- Charge including supply and fixing following items:-(a) Stainless Steel (304 Grade) Finished Butt Hinges 100mm - 4 nos. per leaf(b) Stainless Steel (304 Grade) Finished Square Tower Bolt 200mm long - 2 nos per leaf(c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos. per leaf(d) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos. per leaf(e) Stainless Steel (304 Grade) (natural finish) wire cloth fixing as per manufacture |
| 11 | Kitchen Cabinet Bottom Unit Providing and fixing of machine crafted box type cabinet bottom unit 560mm depth upto using 18/19mm High densiy. High moisture Registance (HDHMR) over 850 Kg/Cum having a alss A fire rating interior grade. Both side laminated. The shutters will also be machine crafted with the same HDHMR. The hinges will be auto loaded hinges. which is of ISI standards. The shelf is to be adjustable with two slots provided at 300mm spacing so as to accommodate the shelf. The plywood should be of thickness 18/19mm HDHMR board. including SS hardware etc complete. |
| 12 | Kitchen Over Head Wall Unit Providing and fixing of machine crafted box type over head unit 325 depth upto using 18/19mm High densiy. High moisture Registance (HDHMR) over 850 Kg/Cum having a alss A fire rating interior grade. Both side laminated. The shutters will also be machine crafted with the same HDHMR. The hinges will be auto loaded hinges. which is of ISI standards. The shelf is to be adjustable with two slots provided at 300mm spacing so as to accommodate the shelf. The plywood should be of thickness 18/19mm HDHMR board. including SS hardware etc complete. |
| 13 | Kitchen Height Storage and Loft Unit Providing and fixing of machine crafted frame work using i using 18/19mm High moisture Registance (HDHMR) over 850 Kg/Cum having a alss A fire rating interior grade. Both side laminated. The shutters will also be machine crafted with the same HDHMR. The hinges will be auto loaded hinges. which is of ISI standards. The shelf is to be adjustable with two slots provided at 300mm spacing so as to accommodate the shelf. The plywood should be of thickness 18/19mm HDHMR board. The same is to be fixed in the location as directed. |
| 14 | Kitchen Accesssories with soft closures SS Grade 304 (i) Cutlery basket 530mm x 510mm x 100mm(ii) Cup & Saucer 380mm x 510mm x 100mm(iii) Plate (Thali) 530mm x 510mm x 150mm(iv) Plain 350mm x 510mm x 150mm(v) Plain 530mm x 510mm x 200mm(vi) Detergent holder 380mm x 510mm x 200mm(Vii)Oil pullout 160mm x 510mm x 585mm(viii)Telescopic drawer channels(ix) Dustbin holder |
| 15 | S & F mild steel 300mm ordinary rat rail rod pattern spring inluding roller and roller plate complete all as specified . |
| 16 | Supply and fixing stainless steel pipe 25mm bore (as a curtain rod), wall thickness of pipe not less than 1mm and grade SS 202, fixed in position with fixing accessories like Brackets, finial and side holder of same manufacturer complete all as specified and as directed by Engineer-in-Charge.Note :(i) Cost for Brackets, finial and side holder ,screws, rawl plugs as required for fixing shall also shall deemed to be included in the quoted unit rate nothing extra shall be paid on this account. |
| 17 | Supply only stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm all as specified . |
| 18 | S & F 4 mm thick sheet glass ordinary quality and glazing with in square not exceeding 0.50 sqm including aluminium cleat/rubber beading in each pane complete all as specified and directed by Engineer - in - Charge. |
| 19 | S & F figured glass 4 mm thick pin head type and glazing with not exceeding 0.50 Sqm including aluminium cleat/rubber beading in each pan complete all as specified and directed by Engineer - in - Charge. |
| 20 | Dismantling of floor hearth or wall tiling including cement mortar bedding ( but not backing) and rubbish off the permices complete all as specified and directed by Engineer - in - Charge. |
| 21 | Material and labour for 7 to 8 mm thick non-skid ceramic colour (light shade) joint free tiles with matt finish premium quality having water absorption should be between 3% to 6%, square/ rectangular, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floor, set and jointed using type-I adhesive (thick bed fixing) confirming to IS-15477:2004 including necessary cutting as per site requirement, complete all as specified and directed by Engineer-in-Charge. |
| 22 | Material and labour for Double charge vitrified coloured tiles (approved shade) of size 600mm x 600mm having thickness 8 to 9 mm premium quality having water absorption less than 0.08%, straight edge, stain free, glossy finish, square marbonite, laid as in floor, set and jointed using type-I adhesive (thick bed fixing) confirming to IS-15477:2004 and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, complete all as specified and directed by Engineer-in-Charge. Make : Johnson (Snow Flair/Albano White Plus/Albano Lemon Plus) or Techno commercial equivalent in make mentioned in Appendix 'B' |
| 23 | All as above item No 22, but as in skirting over 10 mm cement screed bed backing ( 1:3) complete all as specified and directed by Engineer - in - Charge. |
| 24 | Material and labour for Providing and Laying Premium (1st) quality having water absorption should be between 10% to 20%, digitally printed straight edge, punched, glazed ceramic rectangle tile in approved shade and finish with flexural strength greater than 16 N/mm2, scratch hardness on Moh’s Scale minimum 3 and crazing resistance of 2 cycles in coloured tiles 600 X 300 mm and 7 mm thick, in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed using type-I adhesive (thick bed fixing) confirming to IS-15477:2004 and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified.Note : Dado should be flushed with the wall plastering.Make : Johnson (Digital HD Tiles) (Barstow DK/LT/HL for Toilets & Verona LT/HL for Kitchens) or Techno commercial equivalent in make mentioned in Appendix 'B' |
| 25 | Material and labour for anti skid full body vitrified step tiles 10mm thick bull noses and self embossed or grooved in riser, treads & landing (single piece length wise upto 1200mm) including laid over and including screed bed 15mm thick /rendering 10mm thk in CM 1:4 complete all as specified as directed. |
| 26 | Dismantling of stone slab tiling including cement mortar bedding ( but not backing) and rubbish off the permices complete all as specified and directed by Engineer - in - Charge. |
| 27 | Material and labour 16-18mm thickness approved shade granite of minimum size equal to width of slab (not less than 600mm wide, length wise single or two pieces only) machine cut, granite duly factory grinding and polishing and chamfering the outer edges (table rubbed and mirror polished) as in cooking platform/dado /skirting/tread / riser and like laid over and including 15mm thick cement mortar (1:4) screed bed/rendering 10mm thk in CM 1:4 as required including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including accomodate the hole for gas pipe complete all as specified and as directed by Engineer-in-Charge. |
| 28 | Material & labour for 75mm thick PCC 1:3:6 type C1 using 20mm graded stone aggregate as in hard standing ,plinth protection/path etc, laid in suitable panels not exceeding 3.00 m length finished even and smooth without using extra cement with 10mm Joints filled with bituminous sealing compound of grade ‘A’/bitumen mastic filler/sealant complete all as specified and directed by Engineer-in-Charge. |
| 29 | Providing and laying 60mm thick factory made chamfered edge cement concrete paverblock of M-35 grade with approved colour,design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand.complete all as specified and as directed by Engineer-in-Charge.. |
| 30 | Demolition of cement concerete ( un reinforced) of any descripitiion in ground floor and similar suspended work complete all as specified and as directed by Engineer-in-Charge. |
| 31 | M & L for removing of existing roof treatment of any type any thickness upto RCC roof slab including mud fuska,demolation of brick tile or pedding etc and removal of demolation material out of defence land complete all as specified |
| 32 | M& L for 10 mm thick plaster inn CM (1:4) shall be provided mixed with water proofing compound , ISI marked as per manufacturer instructions.The plaster surface shall be steel toweled to get smooth surface. |
| 33 | M&L for roof treatment as specified below and as directed (a) Over the plaster surface apply 1 coat of compatible primer for PU coating as per manufacturers specification. Aloow the primer to touch dry condition.(b) Apply 1st caot of PU coating( ShaliUrethane LHM@ 650 gm/m^2(minimum) or equivalent) by brush/Roller/Spray, sprad water proofing reinforced glass fiber tissue of 150 GSM with overlaps of 75mm in both direction when the surfaces is still tacky. Allow first coat to dry 10-12 hrs.(c) Apply 2nd and 3rd coat of PU membrane (ShaliUrethane LHM@ 650 gm/m^2(minimum) or equivalent) as per manufacture instruction having sun reflective index (SRI) of minimum 106 on top roof surafce after application. Extend waterproofing treatment upto 200 mm and terminate into groove on the parapet wall.Note- (i) The plan area shall be considered for payment(ii) The procurement of material and execuation of the work of water proofuing treatment shall be carried out by authorised applicator apporved by GE.(iii) the manufacture/authorised applicator shall give a warranty for the performance and durablity for 10 years. |
| 34 | Demolition of cement concrete and digging out (unreinforced) as in sunken floor etc of any description and in any position and including removing rubbish material from building and thrown in low lying empty area at any distance as direccted from the site complete all as specified and as directed by Engineer-in-Charge. |
| 35 | M & L for water proofing treatment to RCC sunken slab and adjoining vertical slab as described following any one method Method 1 (A) - Supplying and applying two component elastomeric acrylic polymer modified cementitious waterproofing coating, SmartCare Damp Block 2K or approved equivalent , having 100 % elongation as per ASTM D412, resisting 5 bars hyrostatic pressure as per DIN 1048, reduction to rapid chloride shall be 70 as per DIN 1048, crack bridging upto 1.2mm as per ASTM 4548.5.Clean all working surface & made free from dirt, grease laitance etc. After inspection for all working area rough surface, cracks & construction joint are treated by polymer modified mortar of 1:1:4 (1 Cement : 1Polymer : 4 Sand).Making Gola of size 75X75mm at junction of vertical & horizontal with the polymer modified mortar of 1:1:4 . (1 Cement : 1Polymer : 4 Sand). The coating shall be terminated at 1600mm in toilet/2100mm in bathroom on vertical walls. The mixing ratio of the coating shall be 2 parts of powder & 1 part of liquid without any water addition in the mixing and shall have consumption of 1.5kg/sqm per coats, etc., complete as per manufacturers specifications. (B) Bore Packing: All the borehole gaps between concrete surface and pvc pipe of various dia upto the neck level shall be filled with non-shrink free flow grout - SmartCare GP Grout or approved equivalent having dual shrinkage compensation property. Before the bore packing, surface of the pvc pipe and concrete surface will be made rough and sand will be sprinkled with polymer bonding agent. (c) Apply 12-15mm 1:3 cement plaster on slab and vertical surface admixed with SmartCare Vitalia Neo @200ml per bag of cement Method 2 (A) Providing & applying two component cementitious & acrylic flexible waterproofing & protective coating, two coats with 1mm DFT, having Hydrostatic (positive) water pressure resistance (DIN 1048) is 7. Abrasion resistance, cm/km is 0.09 of Dr Fixit Pidifin 2k @ 1.5kg/sqm or equivalent with a paint brush over existing roof surface. The Polyester reinforced coated net of 45g/m2, 2.5mmx2.5mm is Laying on the surface immediately on the first coat of two component modified polymer Dr Fixit pidifin 2k or equivalent. After removal of all loose materials like dust etc. With wire brush coir brushes from roof surface to get absolutely cleaned surface free of foreign contaminant filling of crack and patches with polymer based repair mortar/micro concrete, repairing with 15 mm thick cement plaster after the repairing work making the gola on surrounding wall’s junction and seal the vertical walls up to 2100 mm. In case of core cutting on the surface, the joint is seal with non-shrink grout. The work complete as per the direction of Engineer-in-Charge. (Work shall be executed through specialized agency) (B) Apply 12-15mm 1:3 cement plaster on slab and vertical surface admixed with SmartCare Vitalia Neo @200ml per bag of cement Note: (i) The treatment shall be carried out as per the manufacturers instructions and as directed by the Engineer in charge. The name of firm shall be got approved from CWE before carrying out the work. (ii) PCC filling under sunken area will be measured & paid separately OR:- Techno commercial equivalent in Fosroc/Sika/STP |
| 36 | Providing plain cement concrete Type E-2, 1:5:10 (40 mm graded stone aggregate as in foundation, filling and mass concrete) complete all as specified and directed by Engineer-in-Charge. |
| 37 | M&L for 25mm thick PCC 1:2:4 type 'B-0' using 12.5 mm graded crushed stone aggregate with a slope of 1:40 complete all as specified and directed by Engineer - in - Charge. |
| 38 | Taking down steel tubing 15mm bore and connections complete all as specified and directed by Engineer - in - Charge. |
| 39 | Supply & fixing of 20mm outer dia CPVC pipes SDR 11 including all fittings Plain/brass threaded CPVC SDR 11 fittings (like Elbow, Tee, Socket, Reducer, Union, Bushing, Step over bends, End cap, End Plugs, one side brass/two side brass etc) fixed along walls, ceiling or laying under floors etc and including CPVC solvent cement for jointing complete all as specified and as directed. |
| 40 | Taking down steel tubing 20mm bore and connections complete all as specified and directed by Engineer - in - Charge. |
| 41 | Supply & fixing of 25mm outer dia CPVC pipes SDR 11 including all fittings Plain/brass threaded CPVC SDR 11 fittings (like Elbow, Tee, Socket, Reducer, Union, Bushing, Step over bends, End cap, End Plugs, one side brass/two side brass etc) fixed along walls, ceiling or laying under floors etc and including CPVC solvent cement for jointing complete all as specified and as directed.NOTE FOR CPVC PIPES : (i) Pipes inside the buildings shall be fixed concealed and outside the buildings shall be fixed on the surface along wall with and including suitable size clamps/brackets of suitable size fixed with fasteners/nut bolts, as directed by Engineer-in-Charge. (ii) Bracket, clamp, nut bolt, fastner, slotted channel etc shall be made of deep drawn low carbon steel material with hot dip zinc aluminium flake coated and fixed all as shown on BTD drawing cost for same shall deemed to be included in the quoted unit rate and nothing extra shall be admissible on this account. (iii) Cost for cutting chases in wall and making good disturbed surfaces as required shall deemed to be included in the quoted unit rate. |
| 42 | S&F 25mm outer dia CPVC Male Brass Threaded Adaptor (MTA/ MBTA) comlete all as specified and directed. |
| 43 | S&F 25mm outer dia CPVC Female Brass Threaded Adaptor (FTA/ FBTA) comlete all as specified and directed. |
| 44 | S&F 25mm outer dia CPVC tank adaptor Brass Threaded comlete all as specified and directed. |
| 45 | S&F 25mm outer dia CPVC Union Brass Threaded comlete all as specified and directed. |
| 46 | S & F rotational moulded polythene three layered white coloured water storage tank with (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I of capacity 500 Litres including Disconnecting existing tanks and removing to store all as specified and directed by Engineer - in - Charge . |
| 47 | M&L Ball brass valves 20mm, high pressure, with polythene float and fly nut complete, screwed for iron pipe of following description complete all as specified and directed by Engineer - in - Charge.. |
| 48 | S & F 20mm bore gunmetal globe or gate valve with iron wheel head screwed both ends for iron pipe or wt 0.68 kg specified in SSR part Iand fixed all as specified . |
| 49 | S & F Grating doom Steelness steel 125 mm dia with or without waste hole of with solvent cement complete all as specified and directed by Engineer - in - Charge. |
| 50 | Taking down old Bib tap/Angular stop cock/basin mixer valve/pillar cock/Ball brass valves etc and deposited at MES AGE store complete all as specified and as directed by Engineer-in-charge. |
| 51 | Supply and fixing Bib taps, CP, fency type long body with wall flange screwed for 15mm bore of iron pipe or for brass ferrule and fixed in position complete all as specified and as directed by Engineer-in-charge.Make : Jaquar (Cat No. VGP-81037) (Vintage Prime) or equivalent from Cera (Valentina Single Lever Series) or equivalent from Hindware (Fluid Series) or Techno commercial equivalent in make mentioned in Appendix 'B' |
| 52 | Supply and fixing Angular Stop Cock with wall flange, fency type chromium plated cast copper alloy screwed down, high pressure, screwed one ends for 15mm bore of iron pipe or for union and fixed in position complete all as specified and as directed by Engineer-in-charge.Make : Jaquar (Cat No. VGP-81053 (Vintage Prime)) or equivalent from Cera (Valentina Single Lever Series) or Techno commercial equivalent in make mentioned in Appendix 'B' |
| 53 | Supply and fixing Stop valves, fancy type, CP with long shank and cup ( concealed type ), exposed part kit with wall flange and regular body of concealed stop cock suitable for 15mm line with protection cap fixed in position complete all as specified and as directed by Engineer-in-charge.Make : Jaquar (Cat No. VGP-81083K (Vintage Prime) & ALD 083) or equivalent from Cera (Valentina Single Lever Series) or Techno commercial equivalent in make mentioned in Appendix 'B' |
| 54 | Supply and fixing single liver basin mixer with popup waste system & 450mm long braided hoses, fency type, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for 15mm bore of iron pipe complete all as specified and as directed by Engineer-in-charge.Make : Jaquar (Cat No. VGP-81051B(Vintage Prime)) or Cera (Cat No - F1013451) or equivalent from Hindware (Fluid Series) or Techno commercial equivalent in make mentioned in Appendix 'B' |
| 55 | Supply and fixing central hole basin mixer valve with regular spout, 15mm bore, brass chromium plated, for mixing hot & cold water, complete with fittings, 450mm long braided hoses with connection and nut for WHB complete all as specified and as directed by Engineer-in-charge.Make : Jaquar (Cat No. CQT-CHR-23167B or Techno commercial equivalent in make mentioned in Appendix 'B' |
| 56 | Supply and fixing single lever High concealed diverter flow consisting of exposed part kit with operating lever , wall flange & button and concealed body ,cartdge sleeve and also including bath spout with flange chromium plated ,screwed down, high pressure complete all as specified and as directed by Engineer-in-charge.Make Cera:(exposed part F1018721, concealed part F4030101, bath Spout F1020661), Jaquar or Techno commercial equivalent in make mentioned in Appendix 'B' |
| 57 | Supply and fixing stainless steel sink with drainage board, AISI 304 quality grade, 1.00 mm thick, glossy finish, for kitchen with plugs washers and CP waste coupling of 32mm dia and including cantilever cast iron brackets, connecting union, etc, overall size 915mm x460/928mmx458mm with bowl size 410x 355x185mm/430x355x200 including bottle trap 32mm with 125mm & 175mm long with wall connection pipe & wall flange and making good disturbed portion in CM 1:3 or PCC 1:2:4 complete all as specified and as directed by Engineer-in-charge.Make : Sink :- Nirali (Elegance) or Diamond (REK 3618) or NeelkanthMake : Bottle Trap :- Hindware (F850015) or Techno commercial equivalent in make mentioned in Appendix 'B' |
| 58 | Supply and fixing Plate Rack / Dish Rack of overall size 900mmx900mm, glossy finish made out of Food Grade Stainless Steel 1mm thick sheet/strip including necessary arrangements for plates and utencils to keep (Holds up to many plates or bowls To accommodate several place settings, Multipurpose), stylish modern streamline design, rust resistant, easy to assemble and clean including fitting accessories fixed in position as directed with SS screws/fasteners etc complete all as directed by Engineer-in-charge. |
| 59 | Supply and fixing in repair vitreous china premium/1st quality wash basin (under counter), white/ivory/off white, size 580x430 mm including S&F all accessories as recommended by manufacturer and incl. brass CP bottle trap 32 mm with inlet and outlet screwed for pipe or connections incl all necessary accessories for fixing, packing, union and incl 32mm brass CP waste coupling and complete fixed in position in all respect as per manufacturer's instructions and taking down existing of any description/size complete all as directed by Engineer-in-charge.Make : Hindware (WHB-Garnet (Cat No.- 10080), Waste Coupling-Cat No.- F850023 (Economy Model), Bottle Trap-Cat No.- F850072 (Economy Model) or Techno commercial equivalent in make mentioned in Appendix 'B' |
| 60 | Supply and fixing vitreous china premium/1st quality wall hung water closet with P trap white/ivory/off white including connection to drain (or out going pipe) and to flushing pipe, antisyphonagee pipe,etc., and incl. plastic soft close seat cover as recommended by manufacturer for particular model closed pattern with flat bottom etc; and incl S&F of all necessary accessories set like rag bolts/gel gasket/hinges etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete in all respect all as specified.Make : Jaquar (Continental Series-CNS-WHT-963N or Techno commercial equivalent in make mentioned in Appendix 'B' |
| 61 | Supply and fixing health faucet (Hand Shower) fancy type, CP including 1.2 meter long 8mm dia wasy flex tube in chrome finish and including wall hook and fixing material, making connections and fixed in position complete all as specified and as directed by Engineer-in-charge. Make: Jaquar(continental series) ALD-573 / Hindware (contessa plus series)/ Cera (Ocean series) or Techno commercial equivalent in make mentioned in Appendix 'B' |
| 62 | Supply and fixing concealed flushing cistern of PVC 8 ltr. cap with dual flushing system, valveless syphonic action type, with inlet/outlet, ball valve, float and including brackets and connection to pipe etc. and incl S&F of all necessary accessories/installation kit and 'S' type drain pipe connetion set for wall hung WC etc as recommended by manufacturer for fixing, packing and including S&F of actuator knob/flush plates and and taking down existing of any description/size complete in all respect all as specified.Make : Jaquar (Concealed Cistern-JCS-WHT-2400S, Flush Plate-JCP-CHR-812415) or Techno commercial equivalent in make mentioned in Appendix 'B' |
| 63 | Supply and fixing PVC Bathroom mirror cabinet of appx size 450mm X 350mm X 140mm (Compact Mirror Cabinet, Concealed shelves) approved quality complete all as specified and as directed by Engineer-in-charge. |
| 64 | Supply and fixing Chromium plated overhead shower 100mm dia with shower arm of 450mm long 20mm dia round shape with 90º bend for wall mounted shower with flange of same make and incl all necessary accessories as recommended by manufacturer for fixing and taking down existing of any description/size complete in all respect all as specified.Make : Jaquar (Shower-OHS-1989, Shower Arm-SHA-479L450) or Techno commercial equivalent in make mentioned in Appendix 'B' |
| 65 | Supply and fixing Towel Ring of Chromium plated fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms), complete, all as specified & directed by Engineer-in-charge. CAT PART No. CAN-1121BN OF Jaquar or Techno commercial equivalent in make mentioned in Appendix 'B' |
| 66 | Supply and fixing toilet paper holder with flat recessed type stainless steel complete all as specified and as directed by Engineer-in-Charge. Make - Jaguar Cat Part No ACN-1151N./Marc/Cera or Techno commercial equivalent in make mentioned in Appendix 'B' |
| 67 | Supply and fixing sheet glass shelf assembly of 300X300mm for corners consisting of 5.5 to 6mm thick glass shelf and with bevelled edges/hatching of edges fixed with stainless steel 'D' bracket fixed and railing complete all as specified and as directed by Engineer-in-Charge. |
| 68 | Taking down CI/AC/PVC soil waste and vent pipe any radius including all fittings complete complete all as specified and directed by Engineer - in - Charge. |
| 69 | Supply & fixing 110mm bore uPVC pipes grade 'B' single socketed in any length with rubber ring joints, fixed along walls with and including suitable size clamps/brackets (interval of 1m and pipe keeping 100mm away from wall ) of suitable size fixed with fasteners/nut bolts, joints fixed with pipe joint lubricant complete all as specified and as directed by Engineer-in- charge.Note:- Bracket, clamp, nut bolt, fastner, slotted channel etc shall be made of deep drawn low carbon steel material with hot dip zinc aluminium flake coated and fixed all as shown on BTD drawing cost for same shall deemed to be included in the quoted unit rate and nothing extra shall be admissible on this account. |
| 70 | Supply & fixing 75mm bore uPVC pipes grade 'B' single socketed in any length with rubber ring joints, fixed along walls with and including suitable size clamps/brackets (interval of 1m and pipe keeping 100mm away from wall ) fixed with fasteners/nut bolts, joints fixed with pipe joint lubricant complete all as specified and as directed by Engineer-in- charge.Note:- Bracket, clamp, nut bolt, fastner, slotted channel etc shall be made of deep drawn low carbon steel material with hot dip zinc aluminium flake coated and fixed all as shown on BTD drawing cost for same shall deemed to be included in the quoted unit rate and nothing extra shall be admissible on this account. |
| 71 | Supply & fixing 110mm bore uPVC pipes grade 'B' single socketed in any length with rubber ring joints, laid in trenches, joints fixed with pipe joint lubricant complete all as specified and as directed by Engineer-in- charge. |
| 72 | Supply & fixing 75mm bore uPVC pipes grade 'B' single socketed in any length with rubber ring joints, laid in trenches, joints fixed with pipe joint lubricant complete all as specified and as directed by Engineer-in- charge. |
| 73 | Supply & fixing uPVC bends (any radius) grade 'B' suitable for 110mm bore pipe complete all as specified and as directed by Engineer-in- charge. |
| 74 | Supply & fixing uPVC bends (any radius) grade 'B' suitable for 75mm bore pipe complete all as specified and as directed by Engineer-in- charge. |
| 75 | Supply & fixing uPVC junction (double T/socket) grade 'B' equal or unequal suitable for 110mm bore pipe complete all as specified and as directed by Engineer-in- charge. |
| 76 | Supply & fixing uPVC junction (double T/socket) grade 'B' equal or unequal suitable for 75mm bore pipe complete all as specified and as directed by Engineer-in- charge. |
| 77 | Supply & fixing uPVC grade 'B' multi floor trap 75mm bore and 600mm long with grating including jointing with with pipe joint lubricant complete all as specified and as directed by Engineer-in- charge. |
| 78 | Supply & fixing uPVC vent cowl grade 'B' suitable for 75mm bore pipe complete all as specified and as directed by Engineer-in- charge. |
| 79 | Material and labour for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment of voids in masonry using chemical emulsion @ one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and as directed by Engineer-in-charge. |
| 80 | Material and labour for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre 300mm apart including drilling depth of holes not less than 300mm and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed by Engineer-in-charge. |
| 81 | Taking down cement plaster from brick walls/soffits of roof projections & chajjas /ceilings etc. including racking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge. |
| 82 | Material and labour for internal plastering 15mm thick in cement mortar (1:6) on any face of Brick walls or concrete surfaces, finished even and fair complete all as specified and as directed by the Engineer-in-Charge. |
| 83 | Material and labour for rendering/plastering 15mm thick in cement mortar (1:4) on any face of Brick wall or concrete surfaces, finished even and fair including mixing of liquid WPC in mortar @ as per manufacturer instruction per bag of cement of 50kg, and fixing of chicken wire gauge where directed complete all as specified and as directed by Engineer-in-Charge. Note : WPC and chicken wire gauge will be measured and paid separately as Supply only) |
| 84 | M & L 5mm thick rendering in Cement Mortar 1:3 on fair faces of brick work or concrete surfaces of ceiling finished even and smooth without using extra cement complete all as specified and directed by Engineer - in - Charge . |
| 85 | Supply only liquid water proofing compound complete all as specified and as directed by the Engineer-in-Charge. Make : Pidilite/Sika/Choksey chemicals/STP Limited |
| 86 | Supply and fixing chicken mesh wire netting 25 gauge, 20mm mesh below the plaster for supporting the same complete all as specified and as directed. |
| 87 | Dismantling of brick work or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, in any description including cleaning and stacking serviceable brick for re use and balance removing rubbish from the site and deposit where directed complete all as specified and as directed by Engineer-in-charge. |
| 88 | Material and labour for brick work with sub class ‘B’ old size burnt clay bricks, straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:6) complete all as specified and as directed by Engineer-in-charge. |
| 89 | Material and labour for brick work (old serviceable bricks obtained from dismantled item shall be reused ) straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:6) complete all as specified and as directed by Engineer-in-charge. |
| 90 | M & L for brick work in half brick thick wall using bricks straight or curved on plan to any radius built in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge. |
| 91 | M&L Providing cement concrete Type D-2, 1:4:8 (40 mm graded stone aggregate as in foundation, filling and mass concrete) complete all as specified and directed by Engineer - in - Charge. |
| 92 | M& L PCC 1:2:4 type B1, using 20 mm graded agg.as in bed blocks ,coping, hold fast blocks etc. |
| 93 | M&L for cement concrete type B0 1:2:4 , 12.5 mm graded stone aggregate in foundation filling and mass concrete for filling depression in base interlocking tiles complete all as specified and directed by Engineer-in-Charge. |
| 94 | Demolition of cement concrete (reinforced) in roof , floors (other than ground floor ), beams, staircase, landing,chajjas and similar suspepnded work complete all as specified and directed by Engineer - in - Charge. |
| 95 | M&L Providing precast cement concrete solid Type B1 1:2:4 20mm agg. building blocks (with plain or interlocking joints as directed) setting in jointed with cement mortar 1:4 (1 cement: 4 coarse sand),complete, in walls, complete all as specified and directed by Engineer - in - Charge. |
| 96 | M&L Precast reinforced cement concrete type B0, 1:2:4 (20 mm graded aggregate) slabs or cover slab for man hole in as required complete all as specified and directed by Engineer - in - Charge. |
| 97 | M&L for leveling course for roof slab, typt B0, 1:2:4 (12.5 mm graded aggregate) for maintaining proper slope and finishing cement concrete surface complete all as specified. (minimum thickness of concrete should not less than 50mm at any point). |
| 98 | M & L mild steel TMT bars 10mm dia or over cut to length bent to shape required including cranking, hooking ends and binding with MS wire (annealed) not less than 0.90mm dia all as in column, beam etc complete all as specified and directed by Engineer - in - Charge. |
| 99 | Ditto all as per above item but 5 mm dia and over up to and including 8 mm dia as in stirrups complete all as specified and directed by Engineer - in - Charge. |
| 100 | Cutting out concrete blocks, slabs, brickwork or stone masonry (in alter nate course), Set in cement mortar 1:6 forming tooth-ings for and bonding new work in mortar into old work,PCC 1:3:6 type B1, using 20 mm graded agg. including new materials entering old wall complete all as specified and directed by Engineer -in -charge. |
| 101 | Excavation in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundations, shafts, wells, cess pits, manholes, for taking out old pipe and laying new pipe line, for laying cable etc, not exceeding 10 Sqm on plan and getting out in soft/loose soil including trimming the sides and forming bottom surfaces to required levels complete all as specified and as directed by Engineer-in-Charge. |
| 102 | Returning filling in including spreading leveling, watering and well ramming in layers n exc 25 mm thick soil complete all as specified and directed by Engineer - in - Charge. |
| 103 | Removing excavated material n exc 1000 m and deposited where directed at a level not exc 1.50 m above the starting point complete all as specified and directed by Engineer - in - Charge. |
| 104 | Supply and fixing 3mm Polycarbonate sheeting with tow plain side lap fixed with coach screw and washer as in chajja in any shape on MS hollow pipe frame complete all as specified and directed.Note :MS frame shall be measured and paid seperately. |
| 105 | Material and labour for mild steel framed work for sun shade/chajja made by using hollow square/rectangular/round pipe (ERW or induction butt welded tubes conforming to latest relevant IS), including making special shaped, bending and welding etc, and including grouting in wall and making good disturbed surface with CM (1:3) complete all as specified and as directed by the Engineer-in-Charge. |
| 106 | Material and labour for Cutting channels, grooves or rebates n exc 15cm girth, and trimming surface with or without reinforcement complete all as specified and as directed by the Engineer-in-Charge. |
| 107 | Excavation in post holes each n. exc. 0.50Cum, getting out in soft/loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc. 25cm, watering and removing surplus soil to a distance n. exc. 50m and making good surface.complete all as specified and directed by Engineer-in-Charge. |
| 108 | M&L for PCC 1:2:4 type B-2 using 40mm graded stone aggregate as in foundation of cols, bdy pillars, posts, struts, etc. filling and mass concrete complete all as specified and directed by Engineer-in-Charge. |
| 109 | S&F Structural steel work in tubular trusses including special shaped washer, Mild steel screw bolts (machine made) size as required at site etc. complete using ERW or induction butt welded tubes grade St-240 complete all as specified and directed by Engineer-in-Charge. |
| 110 | S&F Plates (Plain or chequered) channels,squarecut or notched (ordinary and counter sunk) forming holes, w/o any attachment conforming to FE-290( Gde-E-165 ) complete all as specified and directed Engineer-in-Charge |
| 111 | S & F Pre- painted galvalume aluminum zinc coating GI based corrugated/plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified |
| 112 | Material and labour for preparation of new steel and iron surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint (1st quality) of approved tint/colour over a coat of red oxide primer with using paint brush complete all as specified and as directed by Engineer-in- charge. |
| 113 | Material and labour for complete removal of existing treatment of any type/description from external/internal wall/ceiling surfaces, soffits/chajja/roof projection surfaces etc., by Mechanical sander/grinder machine having suction vaccum Bag (Smart periodical methodology), complete all as specified and as directed by Engineer-in- charge. |
| 114 | Material and labour for new plastered surfaces and prepared surface after complete removal, applying acrylic wall putty in internal/external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony/ceilings etc (thickness vary from 1.5 to 2 mm as required for desired smoothness and levelling of surfaces in two or more layers) by using ready made wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving interior/exterior painting complete all as specified and directed.Notes : (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further external finishes. Please note that the further external finishes work will start only after approval of the prepared surface from the GE as well as to the Engineer-in-Charge through site order. |
| 115 | M&L for Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats after preparation to the new/ old decorated plastered surfaces complete all as specified and as directed by Engineer-in-charge Please Enable Macros to View BoQ information |
| 116 | M&L for Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats after preparation to the new/ old decorated plastered surfaces complete all as specified and as directed by Engineer-in-charge Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 07, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 21, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedNov 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 1 dayTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender