Tender For Special Repair To Shed No 8 (Qm, Ts And Mt Office) And Other Sanctioned Works In Army Area Under Ge (A) No 2 Jodhpur
Tender Value
46.81 Lakhs
Estimated cost
Bid Submission
28 Nov 2026
18 days left
EMD
93620
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jodhpur → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Shed No 8 (Qm, Ts And Mt Office) And Other Sanctioned Works In Army Area Under Ge (A) No 2 Jodhpur
BOQ
| Sl. No. | Item Description |
| 1 | M&L old size brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 including demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches , pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete, all as specified and directed |
| 2 | Taking down cement plaster from brick wall including racking out joints hacking for key scrubbing down with water etc complete. |
| 3 | M&L 15 mm thick rendering in CM (1:4 ) on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing incl finished even and fair complete all as specified. |
| 4 | M&L preparation of new plastered surface of walls and applying two coat of cement based paint over priming plastered and other surfaces with alkaliresistant priming paint complete. |
| 5 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified. |
| 6 | S&F Erection fixing only framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Note -Materials reused obtained from Dismanteling. |
| 7 | S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete |
| 8 | M&L in repair 0.63 mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required |
| 9 | Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings. |
| 10 | M & L Prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall/gate fixed with self tapping screws all as specified & directed. |
| 11 | M & L Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified & directed. |
| 12 | M&L MS framed work as in truss,purlin or rafter of angle iron including distance pieces cleats etc of Fe 410-w(Gde E-250) qualities complete all as specified and directed. |
| 13 | Preparation of new or previously untreated steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide complete all as specified. |
| 14 | Preparation of old treated steel surfaces of any description, over 10cm in width or girth,not otherwise described and applying two coat of synthetic enamel paint complete all as specified. |
| 15 | M&L applying two coat of synthetic enamel painting of steel and iron surfaces of small articles such as metal switch blocks, metal ceiling roses, articles of builder's hardware such as door springs, hooks, knobs, fasteners, stays, locks, latches, etc., straps to roof trusses, gates and similar articles, when unconnected with other painting or when painted in a different tint complete all as specified. |
| 16 | Dismantling expanded metal, any thickness or mesh, fixed with steel or wood fillets, if any |
| 17 | S&F expanded metal, n.exc 4.00 kg cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members complete all as specified. |
| 18 | M&L for machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including 20mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed. |
| 19 | M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over 10mm thick rendering on stone surfaces in CM 1:4 and jointed complete all as specified and as directed. |
| 20 | M&L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete complete all as specified and as directed. |
| 21 | Supply and fixing in repair Gypsum board 600x600x12mm thick (texture finish), whihte prelaminated set embossed reinforced designer ceiling board tiles of approved texture at all height laid on hot dipped galvanised iron imposed grid with 24mm wide T- section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick GS sheet of size 24x32x300mm and spaced at 1200mm c/c securely fixed to be structural soffits by approved hangers at 1200mm c/c. Hangers of GI wire 4mm dia to be fixed by approved rawl plug screw etc. The last hanger at the end of each main runner shall not be grater than 450mm from ajecent wall flush fitting of 1200mm long cross tee (with double stiching) to be interlocked between main runners at 600mm c/c form 600x600mm module cross tee. Perimeter wall angle shall be of 0.45mm thick GS sheet of size 19mm x19mm and 300mm long of white colour all as per manufaturer's and as directed. |
| 22 | M & L for cement concrete (1:3:6) type C-2 using 20 mm graded stone aggregate as in plinth protection/shelve, 50 mm thick, surfaces finished even and fair to receive the stone patti etc including Jodhpur stone roof slabs, Machine cut 45mm to 50mm thick, 25cm to 35cm wide, hoisted and set, jointed and grouted in cement mortar 1:4 complete complete all as specified. |
| 23 | Dismantling timber scantlings 40 sq. cm and over in section, in any position of framed work complete all as specified. |
| 24 | Dismantling boarding, any description, fixed in any positionwith nails |
| 25 | Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors,windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 26 | Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 27 | Providing and fixing 12 mm thick Prelaminated particle board, interior grade,prelaminated both sides with decorative choice laminations,fixed with screws complete all as specified and directed. |
| 28 | S&F 4.8mm thick Sheet glass, ordinary quality and glazing clip of any type and size |
| 29 | S&F Butt hinges,Medium weight, cold rolled mild steel, and fixed |
| 30 | Providing and fixing steel body 100 mm with Mortice lock,vertical type, size 100 mm |
| 31 | M&L for Glazed ceramic COLOURED tiles invertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 15 mm thick screed plaster in cement mortar 1:6 complete all as specified. |
| 32 | M&L Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed plaster in CM 1:4 |
| 33 | Excavation in trenches n.exc 1.5 m wide & n.exc 1.5 m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 Sqm on plan and n.exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and as directed. |
| 34 | Demolition of brick/Stone work built in cement mortar or lime mortar including all quoins arches, pillars etc complete all as specified and directed. |
| 35 | M&L for brick work with old size fly ash bricks, straight or curved on plan exc. 6 M mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 36 | M&L for rolled section as in channel sections fixed independently without connecting plate etc of Fe410-W (grade E-250) quality A as in purposemade lintel complete all as spd |
| 37 | S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 38 | S&F Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in cladding to wall, ridge etc fixed with self tapping screws as specified |
| 39 | S&F MS work in roof trusses (framed), trussed, rials and fastenings and heavy bracket. Framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc with Fe 410.0 or Fe-310.0 complete all as speciafied and directed. |
| 40 | M&L for PCC 1:4:8, Type D2 using 40mm graded aggregate as in foundations, filling and mass concrete complete all as spd and as per dirn of engr in charge. |
| 41 | M&L for RCC Type B1 1:2:4 ( nominal Mix) using 20 mm stone agg as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, chajja, canopies, deck slabs and shelves and the like complete all as spd |
| 42 | Form work to soffits of suspended slabs such as roof slabs, floor slabs and lintels, chajja landing and similar work n exc 200mm thick. |
| 43 | M & L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hoopingfo r columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as spd and directed |
| 44 | M&L for Reinforcement 8 to 10mm dia TMT bars cut to length, bent to shape required and binding with MS wire not less than 0.9mm dia in stirrups complete all as specified and as directed. |
| 45 | Cutting holes into or through brick walls in one brick wall for inserting holdfast built in cement mortar and make good in CM 1:3 or cement concrete 1:2:4 type B1 complete all as spd |
| 46 | Cutting out decayed brick work and refacing with new brick (1 course of headers to 3 courses of strechers) and making goodin CM 1:4 complete all as spd |
| 47 | Forming jambs etc to opening including cutting, toothing and properly bonding into old work also facing, jointing and pointing to match existing work in cement mortar in CM 1:4 or complete |
| 48 | Making good under cills or over lintel including all pinning when necessary in CM 1:4 complete all as sps |
| 49 | Taking down chowkhats with shutters (without taking off shutters from the frame) area exc 1.5 sqm but not exceeding 4 sqm each complete all as specified and as directed. |
| 50 | All as per item No. 09 here-in-above but not exc 1.5 sqm each complete all as specified and as directed. |
| 51 | S&F for powder coating ( minium thickness of power coating 50micron) aluminium frame for doors & window etc with one or more rebates including jointing cleat for fixing etc complete all as spd |
| 52 | S&F for powder coated ( minimum thickness of powder coating not less than 50 micron) aluminium door /window shutter of weighing 0.55Kg/mtr including necessary joining cleats glazing clips rubber packing , powder coated aluminium shop beading with screws, 5mm thick coloured glass and necessary locking arrangement of 4 lever mortise lock and handle 2Nos, hinges et; as specified etc complete all as specified and directed. |
| 53 | M&L for 15-18mm granite (of any type) work (table rubbed and polished) for window sill, door sill, window jamb etc and over 15mm thick screed bed in cement mortar (1:6) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.complete all specified and directed. |
| 54 | M&L for 15 mm rendering thick in CM (1:6) on fair faces of brick work/stone surfaces finished even & smooth (without using extra cement) including taking down cement plaster on brick or stone wall,dado and skirting etc including racking out joints hacking for key scrubbing down with water etccomplete all as specified and directed. |
| 55 | M&L for rendering 15mm thick in two coats (1st coat 10 mm thick in CM 1:6 & 2nd coat 5 mm thick in CM 1:4 with WPC) on fair faces of brick/stone surfaces, finished even & smooth (without using extra cement) including taking down cement plaster on brick or stone wall,dado and skirting etc including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed. Note: WPC in 5 mm thick 2nd layer plaster measured and paid separately. |
| 56 | M&L for 10 mm rendering thick in CM (1:3) on fair faces of concrete surfaces in ceiling finished even & smooth (without using extra cement) including taking down cement plaster on brick or stone wall,dado and skirting etc including racking out joints hacking for key scrubbing down with water etccomplete all as specified and directed. |
| 57 | M&L for preparation of new plastered of wall surface and applying two coats of oil bound distemper, over a coat of chalk whitening primer over and incl a layer 3mm thick of wall care putty to get even and smooth level finish on new plastered surface of internal wall, complete all as specified and as directed. |
| 58 | M&L for preparation of surfaces of walls and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint (weather proof) of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces. complete all as specified and directed.Note : The contractor shall produce batch certificate & delivery challans directly from paint manufacturer to establish the authenticity of the material. The batch testing certificate shall be brought at the site along with paint manufacturer's drums with seal intact. |
| 59 | M&L for preparation of new plastered of ceiling surface and applying three coats of white wash on new plastered surface of ceiling surface, complete all as specified and as directed. |
| 60 | M&L for complete removal of existing treatment and preparation of surfaces of walls by scrapping/sand paper rubbing and finally washing with watering and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint (weather proof) of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces. complete all as specified and directed.Note : The contractor shall produce batch certificate & delivery challans directly from paint manufacturer to establish the authenticity of the material. The batch testing certificate shall be brought at the site along with paint manufacturer's drums with seal intact. |
| 61 | M&L for complete removal of existing treatment by brushing, washing, rubbing down, scraping from old treated surfaces of wall and applying two coat of oil bound distemper over a coat of chalk whitening primer, over a layer of (JK/Birla) 3.0 mm thick wall care putty to get smooth and level finish, complete all as specified and directed. |
| 62 | S&F of 12 mm thick toughned clear glass door frame less with and including chrome finished profiles, roller hanger, patch fittings, hinges ,handles, handrail etc with and incl all respective accessories complete all as directed.Note :- rate hardware including glass included in this item |
| 63 | S&F of 12 mm thick toughned clear glass partition frame less with and including chrome finished profiles, roller hanger, patch fittings, hinges ,handles, handrail etc with and incl all respective accessories complete all as directed. |
| 64 | M&L for complete removal of existing treatment by brushing, washing, rubbing down, scraping from old treated ceiling surfaces and preparation of ceiling surface and applying Three coats of White wash on new plastered surface of ceiling surface, complete all as specified and as directed. |
| 65 | Returning,filling in,including spreading,levelling,watering and well ramming in layers not exc 25 cm each layer in hard/dense soil all as specified and directed. |
| 66 | Removing excavated soil n exc 50 m and depositing where directed at a level n exc 1.5 m above the starting point all as specified and directed. |
| 67 | M&L for preparation of newly steel or iron surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed |
| 68 | Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises, complete all as specified and directed. |
| 69 | M & L for Non- skid Ceramic tiles (Nitco make for exposed area) 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed/ bedding layer in CM (1:6) complete all as specified and as directed. |
| 70 | M&L for Form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides of soffits (if any) of foundations and plinth beams and similar work etc; rough finish surfaces complete all as specified and as directed. |
| 71 | M&L for Form work to sides of concrete pillars, posts, struts, piers, columns and stanchion etc;as in square/rectangular or polygonal of rough finish surfaces complete all as specified and as directed. |
| 72 | M&L for Form work to sides and soffits of floor or roof RCC beam sides of lintel beam flat rough finish surfaces to receive the plaster, complete all as specified and as directed. |
| 73 | M&L for Form work to edges of concrete flats, floor and roofs not exceeding 20cm wide (horizontal or sloping), rough finish surfaces complete all as specified and as directed. |
| 74 | Formwork to chullah hoods, chajjas,troughs and similar items including edges |
| 75 | M&L for Reinforced cement concrete (nominal mix) Type B1 1:2:4 (20 mm graded aggregate) as in foundations, including rafts,footings, foundation beams;plinth beams; bases forcolumns, etc.; basement slabs, under-reamed piles and mass concretein:- complete all as specified and as directed. |
| 76 | M&L for Reinforced cement concrete (nominal mix) Type B1 1:2:4 (20 mm graded aggregate) as in Columns, pillars, piers, posts and struts- complete all as specified and as directed. |
| 77 | M&L for Reinforced cement concrete (nominal mix) Type B1 1:2:4 (20 mm graded aggregate) as in Beams, cantilevers, bressummers,lintels over 1.5m span complete all as specified and as directed. |
| 78 | M&L for Reinforced cement concrete (nominal mix) Type B1 1:2:4 (20 mm graded aggregate) as in Chajjas complete all as specified and as directed. |
| 79 | M & L for 15 mm thick rendering in CM 1:4 using 100% course sand on roof surfaces with WPC @ 3% by weight of cement provided as floating/setting coat of cement complete all as specified and directed (Note :- WPC shall be measured and paid seperatelly) |
| 80 | Supply only integral water proofing liquid ISI marked Make: Pidiproof LW |
| 81 | Forming V grooves in plaster n exc 10mm deep and n exc 10mm on face complete all as specified. |
| 82 | M&L for 75mm thick PCC 1:4:8 type D-2, (40mm graded stone aggregate) as in sub floor, sub bases, floor and paving etc; complete all as specified. |
| 83 | M&L for PCC 1:2:4 type B0 25 mm thick using 12.5mm graded stone aggregates as in sub floors/base floors under tiles as in levelling course etc all as specified and directed. |
| 84 | M&L for glazed ceramic coloured tiles of approved shade and pattern of size 300x600x7 to 8mm thick or any other nearer size as approved by Engineer incharge in vertical surface set and jointed in neat cement slurry and pointed in coloured cement to match laid over 10mm thick screed bed bedding layers in CM 1:4,complete all as specified and as directed. |
| 85 | M&LPowder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gapsat junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanicallywherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions ofEngineer-in-charge Note:- Glass pane & galvanised mild steel wire cloth shall be measured and paid separately. |
| 86 | S&F for figured glass, pin head type ordinary quality, 4mm thick, area of each pane not exceeding 0.5Sqm and glazing with aluminium beading in aluminium frame all as specified and as directed. |
| 87 | S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer -in- charge. complete all as specified. |
| 88 | S&F of Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixingwith stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 89 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheetreinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specifed. |
| 90 | S&F of 100 mm size Butt hinges, heavy weight, cold rolled mild steel, and fixed, complete all as specified and as directed. |
| 91 | S&F of alluminium anodised handles 150 mm long fixed to windows, complete all as specified and as directed. |
| 92 | S&F Aluminium anodised, barrel tower bolts 150 mm long of extruded section and fixed , complete all as specified and as directed. |
| 93 | S&F Aluminium alloy, anodised, sliding door bolt 150 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and as directed. |
| 94 | S&F of 15mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specifide. |
| 95 | S&F of 20mm bore steel water tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floor etc complete all as specifide. |
| 96 | S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified. |
| 97 | M&L vitreous china wash down water closet pan (pedestal pattern), white including white plastic seat cover with mild steel CP hinging device, including making connections and fixed in position complete in all respect as specified. incl making connection to inlet flush pipe, & to 'P' or 'S' drain trap, incl supply of long special 'P' or 'S' trap complete all as specified and directed. |
| 98 | S&F PVC 10 ltr. Cap. valveless syphonic action type, flushing cictern, low level, white/ coloured with inlet, ball valve, float and handle including brackets and connection to pipe etc. all as specified. |
| 99 | S&F 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed. (Minimum weight 142 gms.) all as specified and as directed. |
| 100 | S&F 15mm Bib taps,fency type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified. |
| 101 | S&F 15mm bore stop valve/ angle stop cock chromium plated, fancy type cast copper alloy, screwed down, high pressure, screwed both ends for iron pipe with long shank and cup complete all as specified. |
| 102 | S&F Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) complete all as aspecified and directed. |
| 103 | S&F 100mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, laid in trenches or in floor etc; complete all as specified. |
| 104 | S&F 100mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, fixed to walls etc; complete all as specified. |
| 105 | S&F 75mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, laid in trenches or in floor etc; complete all as specified. |
| 106 | S&F 100mm bore pipe cast iron 'P' or 'S' trap, complete all as specified. |
| 107 | S&F 100mm bore pipe cast iron cowls, complete all as specified. |
| 108 | M&L cast iron up to 150mm bore fittings of Bends (any type, radious and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces, single branch, 'Y' junctions, double branch, cross (all sockets or socket and spigot) collars, caps and plugs etc; complete all as specified. |
| 109 | M&L 100mm bore cast iron pipes and fittings joints or connections are filled/ sealed properly by epoxy sealant of ISI mark or M-Seal (Make:- Dr Fixit) apply as per manufacturing instructions, complete all as specified. |
| 110 | M&L 75mm bore cast iron pipes and fittings joints or connections are filled/ sealed properly by epoxy sealant of ISI mark or M-Seal (Make:- Dr Fixit) apply as per manufacturing instructions, complete all as specified. |
| 111 | S&F for 100mm bore pipes stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall etc; complete all as specified. |
| 112 | Preparation of new plastered surfaces of walls etc. & applying two coats of lime white wash on walls complete all as specified. |
| 113 | M&L for Reinforced concrete pipes, of 150mm bore, class NP3, laid in trenches and jointed in cement mortar as specified complete with collars including all fixing connections complete all as specified. |
| 114 | M&L for PCC (1:3:6) type C2 using 40 mm graded stone aggregate as in surfaces channel and drain of man holes finishing surfaces even and smooth complete all as specified and as directed. |
| 115 | M&L for Jodhpur stone patti slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, laid dry as in manhole coveres / sizes as directed by Engineer incharge complete all as specified and as directed. |
| 116 | S&F vitreous china oval type under counter wash basin, white/ coloured, including PTMT waste fittings, 32mm bore size, waste pipe pvc 32mm bore and angle iron brackets of required size and length etc. and making good disturbed surfaces to match with the existing complete all as specified. |
| 117 | S&F 15mm Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed. |
| 118 | S&F CP towel rail 450mm long fixed with and including CP brass screws and wooden/ plastic cleats complete all as specified. |
| 119 | S&F soap dish, vitreous China white, approximate size 160x 160x90mm fixed toplugs with chromium plated brass screws complete all as specified. |
| 120 | S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed to plugs with chromium plated brass screws complete. |
| 121 | S&F 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed . |
| 122 | S&F Vitreous China Urinal, Half stall type,white including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. including PTMT 32mm waste coupling suitable for Urinals and Urinal Spreder |
| 123 | Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out |
| 124 | M&L Hardcore of broken stone boulders guage exc 63mm but n exc. 100 mm, deposited,spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface |
| 125 | M&L Cement concrete type B-0,1:2:4 (12.50 mm graded stone aggregate) as in kerbs or mud stops,rounded or chamfered on edges as specified and directed. |
| 126 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; |
| 127 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete. |
| 128 | Formwork to faces of walls,retaining walls, abutments,parapets and staircase railingsand similar work including attached pillasters, buttresses,etc.; vertical or to batter of rough finished surface of concrete. |
| 129 | M&L for Reinforced cement concrete (nominal mix) Type B1 1:2:4 (20 mm gradedaggregate) as Walls, retaining walls, basement walls, ballast walls and the like;any thickness; above top of footings; including attached pilaster and buttresses complete all as specified and as directed. |
| 130 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,Complete all as specified. |
| 131 | M&L for 100mm thick PCC 1:4:8 type D-2, (40mm graded stone aggregate) as in sub floor, sub bases, floor and paving etc; complete all as specified. |
| 132 | M&L for PCC 1:2:4 type B0 25 mm thick using 12.5mm graded stone aggregates as in sub floors/base floors under tiles as in levelling course etc all as specified and directed. |
| 133 | M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed inneat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed. |
| 134 | Marble tiles 30cmx20cm x 20mm thick machine cut, bedded jointed and pointed with grey cement slurry including cutting and polishing types of Makrana white including Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes complete all as specified. |
| 135 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.complete all as specifed. |
| 136 | Cutting existing black top road up to 40CM width for passing drain pipe etc.and repairing the hole after insertion of drain pipe etc with cement concrete 1:2:4(1 cement:2 course sand:4 stone aggregate 20mm nominal size) including matching the existing surface of road complete all as specified. |
| 137 | M&L for modular point wiring One light/Fan/bell point /Exhaust fan controlled by one switch one way complete with 1.5 Sq mm single core PVC insulated but unsheathed multistranded copper conductor FR-LSH cable (RYBN) 1100 volts grade drawn through and including non metallic rigid PVC heavy duty concealed conduit with wall thickness not less than 1.8 mm including conduit accessories like bends, tees junction boxes, etc fixed concealed/recessed in wall or ceiling etc including 1.5 Sq mm, single core, PVC insulated but unsheathed multi stranded copper conductor FR-LSH cable (Green) 1100 Volts grade as earth continuity wire connected to earth dolly and including modular sunken galvanized terminal boxes of same make of switch/ socket/ regulator with sleek and curvy cover plates, for mounting of modular switches, sockets, fan regulators complete all as specified and as directed. |
| 138 | Supply and fixing Modular switch 5 Amps one way. |
| 139 | Supply and fixing ceiling rose, 3pin, 5 Amp including connection complete. |
| 140 | Supply and fixing LED lights fitting 20 Watt, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. |
| 141 | Supplying, Installation, Testing & Commissioning of 50 watt Flood Light, powder coated pressure die cast aluminium body with built in or separate driver as per the requirement with Driver efficiency >85%, Input voltage: Input voltage: 140-270 Volt AC, frequency 50/60 HZ, CCT 6500°K, Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc complete all as specified and directed. Please Enable Macros to View BoQ information |
| 142 | Supplying, Installation, Testing & Commissioning of 50 watt Flood Light, powder coated pressure die cast aluminium body with built in or separate driver as per the requirement with Driver efficiency >85%, Input voltage: Input voltage: 140-270 Volt AC, frequency 50/60 HZ, CCT 6500°K, Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 07, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysNov 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender