Tender For Construction Of Udalguri New District Centre (Phase-I).
Tender Value
4.84 Crore
Estimated cost
Bid Submission
27 Nov 2026
8 days left
EMD
9.70 Lakhs
Bank guarantee accepted
Document Fee
9700
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Udalguri → Assam
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Udalguri New District Centre (Phase-I).
BOQ
| Sl. No. | Item Description |
| 1 | A. CIVIL WORKS 2.8 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.2.8.1 All kinds of soil. |
| 2 | 2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift. |
| 3 | 2.27 Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 4 | 2.34 Supplying chemical emulsion in sealed containers including delivery as specified.2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% |
| 5 | 2.35 Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 6 | 16.12 Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete :16.12.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 7 | 4.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :4.1.6 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 8 | 4.17 Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 9 | 4.1 Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources) |
| 10 | 5.9 Centring and shuttering including strutting,propping etc. and removal of form for5.9.1 Foundations, footings, bases of columns, etc. for mass concrete |
| 11 | 5.9 Centring and shuttering including strutting,propping etc. and removal of form for5.9.5 Lintels, beams, plinth bams, griders, bressumers and cantilevers. |
| 12 | 5.9 Centring and shuttering including strutting,propping etc. and removal of form for5.9.3 Suspended floors, roofs, landings, balconies and access platform |
| 13 | 5.9 Centring and shuttering including strutting,propping etc. and removal of form for5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts |
| 14 | 5.9 Centring and shuttering including strutting,propping etc. and removal of form for5.9.7 Stairs, (excluding landings) except spiral-staircases |
| 15 | 5.1 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :5.1.1 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources) |
| 16 | 5.2 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :5.2.1 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natu ral sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 17 | 5.3 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 18 | 5.22 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 19 | 5.22A Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 20 | 6.1 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in6.1.1 Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 21 | 6.4 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 22 | 13.3 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.13.3.1 Cement mortar 1:3 (1 cement :3 coarse sand) |
| 23 | Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. |
| 24 | 9.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).9.1.1 Second class teak wood |
| 25 | 9.53 Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). |
| 26 | 9.21 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 27 | 9.22 Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I)9.22.1 On one side only |
| 28 | 9.74 Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :9.74.1 250x10 mm |
| 29 | 9.74 Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :9.74.3 150x10 mm |
| 30 | 9.82 Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. |
| 31 | 9.81 Providing and fixing bright finished brass handles with screws etc. complete:9.81.1 125 mm |
| 32 | 9.83 Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 33 | 9.48 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.9.48.2 Fixed to openings /wooden frames with rawl plugs screws etc. |
| 34 | 9.147D Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.9.147D.5 Three track three panels sliding window made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) |
| 35 | 9.147D Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.9.147D.1 Two track two panels sliding window made of (small series)frame 52 x 44 mm &sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm |
| 36 | 21.3 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):21.3.2 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 37 | 11.4 52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 38 | 11.41A Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.11.41A.2 Glazed vitrified floor tiles polished finish of size11.41A.2.2 Size of Tile 600 x 1200 mm |
| 39 | 11.41A Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size11.41A.3.1 Size of Tile 600 x 600 mm |
| 40 | 11.46 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.11.46.2 Size of Tile 600x600 mm |
| 41 | 8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 42 | 11.56 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.11.56.1 Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent |
| 43 | 13.1 12mm cement plaster of mix :13.1.21 1:4 (1 cement: 4 fine sand) |
| 44 | 13.5 15 mm cement plaster on rough side of single or half brick wall of mix:13.5.1 1:4 (1 cement: 4 fine sand) |
| 45 | 13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 46 | 13.60 Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :13.60.1 Two or more coats on new work |
| 47 | 13.46 Finishing walls with Acrylic Smooth exterior paint of required shade :13.46.1 New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 48 | 13.61 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :13.61.1 Two or more coats on new work |
| 49 | 12.41 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.12.41.2 110 mm diameter |
| 50 | 12.42 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.12.42.5 Bend 87.5°12.42.5.2 110 mm bend |
| 51 | 12.42 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.12.42.6 Shoe (Plain)12.42.6.2 110 mm Shoe |
| 52 | 12.43 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.12.43.2 110 mm |
| 53 | 12.45 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.45.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) |
| 54 | B. SANITARY INSTALLATION & WATER SUPPLY17.3 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 17.3.1 W.C. pan with ISI marked white solid plastic seat and lid each |
| 55 | 17.22 Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan. |
| 56 | 17.16A Providing and fixing 8 mm dia C.P. / S.S. jet with flexible tube up to 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer-in-charge. |
| 57 | 17.7.3 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required. White vitreous china wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps. |
| 58 | 17.31 Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 59 | 17.73.1 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms. |
| 60 | 18.65 Providing and fixing PTMT soap dish holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements, weighing not less than 106 gms. |
| 61 | 17.34.2 Providing and fixing toilet paper holder - vitreous china. |
| 62 | 17.5 Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :17.5.1 Single half stall urinal with 5 litre P.V.C. automaticflushing cistern |
| 63 | 17.1 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :17.10.1 Kitchen sink with drain board17.10.1.1 510x1040 mm bowl depth 250 mm |
| 64 | 17.22A Providing and fixing CP Brass 32 mm size bottle trap of approved quality and make as per the direction of Engineer-in-charge. |
| 65 | 17.60.2.2 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors. 100 mm inlet and 75 mm outlet, sand cast iron S&S as per IS:1729. |
| 66 | 17.35.1.1 Providing and fixing soil, waste and vent pipes. 100 mm dia sand cast iron S&S pipe as per IS:1729. |
| 67 | 17.35.2.1 Providing and fixing soil, waste and vent pipes. 75 mm dia sand cast iron S&S pipe as per IS:1729. |
| 68 | 17.39.1.1 Providing and fixing plain bend of required degree. 100 mm dia sand cast iron S&S as per IS:1729. |
| 69 | 17.44.1.1 Providing and fixing single equal plain junction of required degree. 100x100x100 mm sand cast iron S&S as per IS:1729. |
| 70 | 17.39.2.1 Providing and fixing plain bend of required degree. 75 mm dia sand cast iron S&S as per IS:1729. |
| 71 | 17.44.2.1 Providing and fixing single equal plain junction of required degree. 75x75x75 mm sand cast iron S&S as per IS:1729. |
| 72 | 17.36.2 Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 (1 cement : 2 fine sand) in S.C.I./C.I. pipes. 100 mm dia pipe. |
| 73 | 17.36.1 Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 (1 cement : 2 fine sand) in S.C.I./C.I. pipes. 75 mm dia pipe. |
| 74 | 17.59.1 Providing and fixing M.S. stays and clamps for sand cast iron / centrifugally cast (spun) iron pipes of diameter 100 mm. |
| 75 | 17.59.2 Providing and fixing M.S. stays and clamps for sand cast iron / centrifugally cast (spun) iron pipes of diameter 75 mm. |
| 76 | 17.65.1 Painting sand cast iron / centrifugally cast (spun) iron soil, waste, vent pipes and fittings with two coats of synthetic enamel paint over a coat of primer (of approved quality) for new work. 100 mm diameter pipe. |
| 77 | 17.65.2 Painting sand cast iron / centrifugally cast (spun) iron soil, waste, vent pipes and fittings with two coats of synthetic enamel paint over a coat of primer (of approved quality) for new work. 75 mm diameter pipe. |
| 78 | 18.49.1 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931. 15 mm nominal bore. |
| 79 | 18.16.1 Providing and fixing brass stop cock of approved quality. 15 mm nominal bore. |
| 80 | 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 81 | 18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.External work18.9.6 50 mm nominal dia Pipes |
| 82 | 18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall18.7.5 40 mm nominal dia Pipes |
| 83 | 18.8.4 CPVC pipes, concealed work, as per item above. 32 mm nominal dia pipes. |
| 84 | 18.8.3 CPVC pipes, concealed work, as per item above. 25 mm nominal dia pipes. |
| 85 | 18.8.2 CPVC pipes, concealed work, as per item above. 20 mm nominal dia pipes. |
| 86 | 18.8.1 CPVC pipes, concealed work, as per item above. 15 mm nominal dia pipes. |
| 87 | 18.17.1 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end). 25 mm nominal bore. |
| 88 | 18.17.2 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end). 32 mm nominal bore. |
| 89 | 18.17.4 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end). 50 mm nominal bore. |
| 90 | 18.62 Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball18.62.5 50 mm nominal bore, 242mm long, weighing not less than 1240 gms |
| 91 | C. SEPTIC TANK (2 NOS.)2.8 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m2.8.1 All kinds of soil. |
| 92 | 2.27 Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 93 | 4.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :4.1.3 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 94 | 5.22 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 95 | 5.9 Centering and shuttering including strutting, propping etc. and removal of form for5.9.1 Foundations, footings, bases of columns, etc. for mass concrete |
| 96 | 5.9 Centering and shuttering including strutting, propping etc. and removal of form for5.9.3 Suspended floors, roofs, landings, balconies and access platform sqm |
| 97 | 5.9 Centering and shuttering including strutting, propping etc. and removal of form for5.9.13 Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards |
| 98 | 6.2 Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in:6.2.1 Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 99 | 5.1 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 100 | 6.13 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) |
| 101 | 13.2 15 mm cement plaster on the rough side of single or half brick wall of mix :13.2.1 1:4 (1 cement: 4 fine sand) |
| 102 | 11.6 Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement.11.6.1 18 mm thick |
| 103 | D. ELECTRICAL WORKS:::upply of 3.5C x 150 sq.mm Al. XLPE armoured 1.1 kV cable - incoming service from DISCOM pole / transformer to meter room (DSR Ch.7 covers laying only) |
| 104 | 7.1.2 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Above 35 sq. mm and upto 95 sq. mm |
| 105 | 7.1.1 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. mm |
| 106 | 7.7.2 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp) |
| 107 | 7.7.1 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sq. mm (clamped with 1mm thick saddle) |
| 108 | 9.1.24 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 95 sq. mm (45mm) |
| 109 | 9.1.21 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 35 sq. mm (32mm) |
| 110 | 14.16.2 Supplying and laying of DWC HDPE pipe ISI marked, 90 mm dia (OD-90 mm & ID-76 mm nominal) along with accessories conforming to IS 14930 Part II, direct in ground (75 cm below GL) including excavation and refilling, for protection of underground cable. |
| 111 | 14.13.2 Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep) and re-filling etc as required. a) 80 mm dia |
| 112 | 12.38 Supplying and fixing of light class G.I. pipe of 80 mm dia. (nominal) 3 metres length along the pole for protection of under ground cable as required. |
| 113 | Weather-proof sheet-steel meter box (IP54) with transparent window and sealing provision for 3-phase DISCOM energy meter - supply and fixing (meter supplied by DISCOM) |
| 114 | Main LT panel 415 V, 250 A TPN, floor mounted, CRCA sheet steel: 4-pole 250 A MCCB incomer, copper busbar, 4 nos. 4-pole 100 A MCCB outgoing, ammeter / voltmeter with selector switches, indicating lamps, earth bar (without SPD) - supply and fixing |
| 115 | 4-pole 200 A manual changeover switch (mains / DG-inverter) in IP55 sheet-steel enclosure, with connections |
| 116 | Surge protection device Type-2, 40 kA, 4-pole, with backup fuse |
| 117 | Supply of 3.5C x 35 sq.mm Al. XLPE armoured 1.1 kV cable - feeders from main LT panel to ground floor DB, first floor DB and kitchen / common DB (DSR Ch.7 covers laying only) |
| 118 | 7.1.1 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. mm |
| 119 | 7.7.1 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sq. mm (clamped with 1mm thick saddle) |
| 120 | 6.2 Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required. |
| 121 | 6.7 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For horizontal run) |
| 122 | 6.8 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run) |
| 123 | 6.12 Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required |
| 124 | 5.4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 125 | 5.16 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required |
| 126 | 5.18 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. |
| 127 | 5.12 Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required |
| 128 | 6.14 Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required |
| 129 | Compound lighting pole: 4 m GI tubular pole with 30 W LED street / garden light fitting, base plate, foundation bolts and junction box (civil foundation excluded) - supply and fixing |
| 130 | Armoured copper cable 1.1 kV XLPE, 4C x 6 sq.mm, for external lighting circuits - supply only (laying under DSR 7.1.1) |
| 131 | 7.1.1 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. Upto 35 sq. mm |
| 132 | Outdoor lighting control box (IP65): 3-phase MCB incomer, contactors, timer / photocell control, with connections - supply and fixing |
| 133 | Sundries for service connection: cable lugs and glands, cable route markers and warning tape, danger / caution plates, GI nuts and bolts, ferrules, earthing links, testing, commissioning and DISCOM inspection support (lump sum) |
| 134 | 1.10.1 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group A |
| 135 | 1.27.3 Supplying and fixing following size/modules, GI Box along with modular base and cover plate for modular switches in recess etc as required. 4 Module (125mmX75mm) |
| 136 | 1.27.4 Supplying and fixing following size/modules, GI Box along with modular base and cover plate for modular switches in recess etc as required. 6 Module (200mmX75mm) |
| 137 | 1.27.6 Supplying and fixing following size/modules, GI Box along with modular base and cover plate for modular switches in recess etc as required. 12 Module (200mmX150mm) |
| 138 | 1.24.1 Supplying and fixing following modular switch/socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required. 5/6 A switch |
| 139 | 1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 140 | 1.45 Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. |
| 141 | BLDC Ceiling Fan, 1200 mm, 350 RPM. Make: Bajaj |
| 142 | Supply, Installation, Testing and Commissioning Wall Mounted Fan. Make: Crompton |
| 143 | Installation, testing and commissioning of wall bracket / ceiling fittings of all sizes and shapes containing up to two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required. |
| 144 | Supply, Installation, Testing and Commissioning LED Batten (20 Watts). Make: Philips |
| 145 | 12W Ceiling Panel Light. Make: Bajaj |
| 146 | 36W Cool White LED Panel Square Light, Base Type: 2ft x 2ft. Make: Bajaj |
| 147 | 20W LED recessed COB downlight, 150 mm cut-out (reception / meeting room / lounge / conference hall) |
| 148 | Supply, Installation, Testing and Commissioning 9W Led Bulb. Make: Crompton |
| 149 | 9W LED mirror / vanity light, IP44, toilet |
| 150 | 150W LED Flood Light Make: Bajaj |
| 151 | Supply, Installation, Testing and Commissioning 20W Led Flood Light. Make: Crompton |
| 152 | 1.50.1 Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required – up to 450 mm sweep. |
| 153 | 150 mm Exhaust Fan Make: Bajaj |
| 154 | 2.3.3 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way, Double door |
| 155 | 2.10.1 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. a) Single pole |
| 156 | 2.12.1 Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A |
| 157 | 2.14.2 Supplying and fixing following rating, double pole (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A |
| 158 | 12-way TPN MCB distribution board, double door, IP43, with busbars and earth bar (without MCBs) |
| 159 | 4-pole 63 A, 30 mA RCCB in TPN DB, with connections |
| 160 | 4-pole 63 A isolator in TPN DB, with connections |
| 161 | 3-pole 32 A \\"C\\" curve MCB in TPN DB, with connections |
| 162 | Surge protection device Type-2, 40 kA, 4-pole, with backup fuse (floor DB) |
| 163 | MR-27 Rechargeable LED emergency light 8 W, 3-hour backup - supply only, installation under DSR 1.35 |
| 164 | LED exit sign with 3-hour battery backup, wall / ceiling mount - supply only, installation under DSR 1.35 |
| 165 | LED cove strip light 14 W/m, 24 V DC, with aluminium profile and driver (reception / dining / lounge) |
| 166 | Conventional fire alarm control panel, 8-zone, with battery backup - supply and fixing |
| 167 | Conventional optical smoke detector with base |
| 168 | Conventional manual call point (break-glass) |
| 169 | Hooter-cum-strobe, 24 V DC |
| 170 | FRLS 2C x 1.5 sq.mm shielded fire-alarm cable in conduit - supply and laying |
| 171 | 4 MP IP dome camera with PoE and mount |
| 172 | 16-channel NVR with 4 TB surveillance hard disk |
| 173 | 24-port PoE+ managed network switch |
| 174 | 12U wall rack with patch panel, cable managers and PDU |
| 175 | Cat-6 U/UTP cable in conduit / tray - supply and laying |
| 176 | Cat-6 information outlet with patch cord |
| 177 | Wi-Fi 6 ceiling-mount access point |
| 178 | Sundries for internal installation: ferrules, lugs, cable ties, clips, saddles, insulation tape, circuit labelling, DB legends, danger plates, testing and commissioning (lump sum) |
| 179 | 1.14.1 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required. a) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 180 | 1.14.4 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required. b) 2 X 6 sq. mm + 1 X 6 sq. mm earth wire |
| 181 | 1.14.11 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required. c) 4 X 16 sq. mm + 2 X 6 sq. mm earth wire |
| 182 | 1.21.1 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. (Extra / spare conduit only – item 1.14 already includes conduit; taken as 10% of 1.5 sq.mm circuit length) 20 mm |
| 183 | 1.21.3 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 32 mm |
| 184 | 1.27.3 Supplying and fixing following size/modules, GI Box along with modular base and cover plate for modular switches in recess etc as required. 4 Module (125mmX75mm) |
| 185 | 1.27.4 Supplying and fixing following size/modules, GI Box along with modular base and cover plate for modular switches in recess etc as required. 6 Module (200mmX75mm) |
| 186 | 1.27.6 Supplying and fixing following size/modules, GI Box along with modular base and cover plate for modular switches in recess etc as required. 12 Module (200mmX150mm) |
| 187 | 1.24.1 Supplying and fixing following modular switch/socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required. 5/6 A switch |
| 188 | 1.24.3 Supplying and fixing following modular switch/socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required. 15/16 A switch |
| 189 | 1.24.4 Supplying and fixing following modular switch/socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 A socket outlet |
| 190 | 1.24.5 Supplying and fixing following modular switch/socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required. 6 pin 15/16 A socket outlet |
| 191 | 1.26 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 192 | 5 A modular socket with 2.1 A dual USB (A + C) charger, 2-module, with plate - supply and fixing |
| 193 | Hotel-type key-card energy-saver switch, 32 A, with plate - supply and fixing |
| 194 | Shaver socket 115/230 V dual voltage with isolating transformer, with plate - supply and fixing |
| 195 | Water cooler / geyser 15 A power point with MCB and 20 A switch, complete in 6 module box - supply and fixing |
| 196 | Server room / strong room dedicated 6 A UPS power point with MCB, complete - supply and fixing |
| 197 | Sundries for power wiring: ferrules, lugs, junction boxes, cable clips, spacers, insulation tape, circuit labelling, testing and commissioning (lump sum) |
| 198 | E. FIRE FIGHTINGSupplying and placing Eco Extinguisher 4 kg Premium ABC dry powder type fire extinguisher, red (stored pressure, IS:15683), complete with wall mounting bracket. |
| 199 | Supplying and placing Agni-X 4.5 kg fire extinguisher, carbon dioxide gas, 131.56 bar testing pressure and 18 sec. discharge time, model PSS-CO2FE-4.5, complete with wall mounting bracket. |
| 200 | F. EARTH FILLING (RAISING LOW SITE) 2.38 Filling with available fly ash and earth (excluding rock) in trenches or embankment in layers (each layer should not exceed 15 cm), with intermediate layer of compacted earth (Soil density of 98%) after every four layers of compacted depth of fly ash, sides & top layer of filling shall be done with earth having total minimum compacted thickness 30 cm or as decided by Engineer -in-charge, including compacting each layer by rolling/ ramming and watering, all complete as per drawing and direction of Engineer -in - charge. |
| 201 | G. FURNITURE & FIXTURES Reception counter (L-shaped/straight) 750 mm deep x 1100 mm high, 18 mm BWP marine ply carcass, 1 mm decorative laminate both sides, 25 mm thick granite/solid-surface top, with lockable drawers, cable port and hardware complete |
| 202 | Executive officer table 1800 x 900 x 750 mm with side return 1200 x 450 mm, 25 mm pre-lam board top, 3-drawer pedestal with central lock, modesty panel and wire manager |
| 203 | Executive high-back revolving chair, PU leatherette upholstery, adjustable height with tilt-lock mechanism, chrome base and padded arms |
| 204 | Visitor chair, cushioned seat & back, powder-coated MS tubular frame with arms, fixed type |
| 205 | Staff workstation table 1200 x 600 x 750 mm, 25 mm pre-lam board top, with 3-drawer mobile pedestal and keyboard tray |
| 206 | Staff medium-back revolving chair, fabric upholstery, gas-lift height adjustment, nylon base with castors |
| 207 | Main conference table 6000 x 1500 mm (20-seater), modular type, 38 mm veneer/laminate top with wire management boxes and 4 nos. power/data flip-up ports, MS legs powder-coated |
| 208 | Conference chair, high-back mesh/leatherette, fixed arms, chrome base, ergonomic |
| 209 | Meeting table 3600 x 1200 mm (10-seater), 25 mm laminate top, MS/wood legs, with cable tray |
| 210 | Meeting room chair, medium-back cushioned, fixed arms, chrome frame |
| 211 | Sofa set 3+1+1 seater, kiln-dried hardwood frame, high-density foam, leatherette upholstery |
| 212 | Centre table 1000 x 600 mm with 2 nos. side tables, toughened glass top and SS/wood frame |
| 213 | Waiting bench, 3-seater, perforated stainless steel (SS 304) seat & back with MS tubular legs, floor-fixed |
| 214 | Steel almirah 1980 x 910 x 480 mm, 2-door, 0.8 mm CRCA sheet, 4 adjustable shelves, locker & powder-coated finish |
| 215 | Steel record rack (library type) 2000 x 900 x 450 mm, 5-shelf, 0.7 mm CRCA sheet with angle frame, powder-coated |
| 216 | Four-drawer steel filing cabinet with central lock, 0.8 mm CRCA sheet, powder-coated |
| 217 | Staff locker, 12-compartment, 0.7 mm CRCA sheet with individual locks, powder-coated |
| 218 | Pantry base & wall cabinet unit, 18 mm BWR ply carcass with laminate finish, 18 mm granite counter, SS sink provision, tall unit with shutters |
| 219 | Dining / break-room table 4-seater 1200 x 750 mm with 4 nos. cushioned chairs |
| 220 | Roller / vertical blinds, 100 mm louvres / blackout fabric, with channel, cords and fixing hardware complete |
| 221 | Whiteboard / pin-up notice board 1200 x 900 mm, aluminium frame, wall-mounted |
| 222 | Toilet accessories set: 600 x 450 mm bevelled mirror, liquid soap dispenser, paper-roll holder, napkin bin, 2 nos. robe hooks (SS 304) |
| 223 | Stainless steel pedal-type dustbin 20 ltr capacity |
| 224 | Wall clock, 300 mm dia, quartz, mounted on wall |
| 225 | Acrylic room sign / name plate 300 x 100 mm with SS standoff fixings |
| 226 | Key cabinet / key box, 48 keys, steel, wall-mounted Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 07, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 27, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 8 daysNov 27, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender