Public Administrative Department Government Departments Closing in 8 days TDR #58434386

Tender For Construction Of Devnath Basumatary Guest House At Dimakuchi (G+1, 15 Rooms With Meeting Hall).

Issued by Government Departments · udalguri, Assam
Tender Value
4.84 Crore
Estimated cost
Bid Submission
27 Nov 2026
8 days left
EMD
9.70 Lakhs
Bank guarantee accepted
Document Fee
9700
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
udalguri → Assam
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender for Construction Of Devnath Basumatary Guest House At Dimakuchi (G+1, 15 Rooms With Meeting Hall).

BOQ

Name of Work:- Construction of Devnath Basumatary Guest House at Dimakuchi (G+1, 15 rooms with Meeting Hall).
Sl. No. Item Description
1A. CIVIL WORKS 2.8 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.2.8.1 All kinds of soil.
22.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift.
32.25(a) Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.
42.27 Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.
52.34 Supplying chemical emulsion in sealed containers including delivery as specified.2.34.1 Chlorpyriphos/ Lindane emulsifiable concentrate of 20%
62.35 Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration
716.12 Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete :16.12.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
84.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :4.1.6 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources)
94.17 Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
104.1 Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources)
115.9 Centring and shuttering including strutting,propping etc. and removal of form for5.9.1 Foundations, footings, bases of columns, etc. for mass concrete
125.9 Centring and shuttering including strutting,propping etc. and removal of form for5.9.5 Lintels, beams, plinth bams, griders, bressumers and cantilevers.
135.9 Centring and shuttering including strutting,propping etc. and removal of form for5.9.3 Suspended floors, roofs, landings, balconies and access platform
145.9 Centring and shuttering including strutting,propping etc. and removal of form for5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts
155.9 Centring and shuttering including strutting,propping etc. and removal of form for5.9.7 Stairs, (excluding landings) except spiral-staircases
165.1 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :5.1.1 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size de rived from natural sources)
175.2 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :5.2.1 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natu ral sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
185.3 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).
195.22 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more
205.22A Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more.
216.1 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in6.1.1 Cement mortar 1:4 (1 cement : 4 coarse sand)
226.4 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand)
239.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).9.1.1 Second class teak wood
249.53 Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).
259.21 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
269.22 Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I)9.22.1 On one side only
279.74 Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :9.74.1 250x10 mm
289.74 Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :9.74.3 150x10 mm
299.82 Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.
309.81 Providing and fixing bright finished brass handles with screws etc. complete:9.81.1 125 mm
319.170 Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge.9.170.1 200 mm
329.88 Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.
339.83 Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.
349.48 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.9.48.2 Fixed to openings /wooden frames with rawl plugs screws etc.
359.147D Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.9.147D.5 Three track three panels sliding window made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm)
369.147D Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.9.147D.1 Two track two panels sliding window made of (small series)frame 52 x 44 mm &sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm
37Analysis- I: Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).
3821.3 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):21.3.2 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)
3911.4 52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.
4011.41A Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.11.41A.2 Glazed vitrified floor tiles polished finish of size11.41A.2.2 Size of Tile 600 x 1200 mm
4111.41A Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size11.41A.3.1 Size of Tile 600 x 600 mm
4211.46 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.11.46.2 Size of Tile 600x600 mm
438.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
4411.56 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.11.56.1 Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent
4513.1 12mm cement plaster of mix :13.1.21 1:4 (1 cement: 4 fine sand)
4613.5 15 mm cement plaster on rough side of single or half brick wall of mix:13.5.1 1:4 (1 cement: 4 fine sand)
4713.80 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
4813.60 Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :13.60.1 Two or more coats on new work
4913.46 Finishing walls with Acrylic Smooth exterior paint of required shade :13.46.1 New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)
5013.61 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :13.61.1 Two or more coats on new work
5110.16 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.10.16.1 Hot finished welded type tubes
5212.50 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
5312.4 Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.12.4.1 0.63 mm thick with zinc coating not less than 275 gm/m²
5412.7 Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete12.7.1 0.80 mm thick with zinc coating not less than 275 gm/m²
5512.41 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.12.41.2 110 mm diameter
5612.42 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.12.42.5 Bend 87.5°12.42.5.2 110 mm bend
5712.42 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.12.42.6 Shoe (Plain)12.42.6.2 110 mm Shoe
5812.43 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.12.43.2 110 mm
5912.45 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.45.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)
6017.3 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 17.3.1 W.C. pan with ISI marked white solid plastic seat and lid each
6117.18.1 Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures complete. 10 litre capacity - white.
6217.20.1 Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete. White solid plastic seat with lid.
6317.22 Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan.
6417.16A Providing and fixing 8 mm dia C.P. / S.S. jet with flexible tube up to 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer-in-charge.
6517.7.3 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required. White vitreous china wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps.
6617.14 Providing and fixing white vitreous china half stall urinal with 15 mm C.P. brass spreader / flush connection, 32 mm C.P. brass waste, C.I. brackets, including painting of fittings and brackets, cutting and making good the walls and floors wherever required.
6717.18.2 Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures complete. 5 litre capacity - white (for urinals).
6817.31 Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
6917.73.1 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms.
70ITEM NO:-11 18.65 Providing and fixing PTMT soap dish holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements, weighing not less than 106 gms.
7117.34.2 Providing and fixing toilet paper holder - vitreous china.
7217.22C Providing and fixing C.P. brass health faucet of approved quality with 1 metre long flexible tube, wall hook and 15 mm brass angle valve complete.
7317.22A Providing and fixing CP Brass 32 mm size bottle trap of approved quality and make as per the direction of Engineer-in-charge.
7417.60.2.2 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors. 100 mm inlet and 75 mm outlet, sand cast iron S&S as per IS:1729.
7517.35.1.1 Providing and fixing soil, waste and vent pipes. 100 mm dia sand cast iron S&S pipe as per IS:1729.
7617.35.2.1 Providing and fixing soil, waste and vent pipes. 75 mm dia sand cast iron S&S pipe as per IS:1729.
7717.39.1.1 Providing and fixing plain bend of required degree. 100 mm dia sand cast iron S&S as per IS:1729.
7817.44.1.1 Providing and fixing single equal plain junction of required degree. 100x100x100 mm sand cast iron S&S as per IS:1729.
7917.39.2.1 Providing and fixing plain bend of required degree. 75 mm dia sand cast iron S&S as per IS:1729.
8017.44.2.1 Providing and fixing single equal plain junction of required degree. 75x75x75 mm sand cast iron S&S as per IS:1729.
8117.56.1.1 Providing and fixing terminal guard. 100 mm sand cast iron S&S as per IS:1729.
8217.36.2 Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 (1 cement : 2 fine sand) in S.C.I./C.I. pipes. 100 mm dia pipe.
8317.36.1 Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 (1 cement : 2 fine sand) in S.C.I./C.I. pipes. 75 mm dia pipe.
8417.59.1 Providing and fixing M.S. stays and clamps for sand cast iron / centrifugally cast (spun) iron pipes of diameter 100 mm.
8517.59.2 Providing and fixing M.S. stays and clamps for sand cast iron / centrifugally cast (spun) iron pipes of diameter 75 mm.
8617.65.1 Painting sand cast iron / centrifugally cast (spun) iron soil, waste, vent pipes and fittings with two coats of synthetic enamel paint over a coat of primer (of approved quality) for new work. 100 mm diameter pipe.
8717.65.2 Painting sand cast iron / centrifugally cast (spun) iron soil, waste, vent pipes and fittings with two coats of synthetic enamel paint over a coat of primer (of approved quality) for new work. 75 mm diameter pipe.
8817.22B Providing and fixing CP Brass single lever telephonic wall mixer of quality and make as approved by Engineer-in-charge. 15 mm nominal dia.
8918.49.1 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931. 15 mm nominal bore.
9018.16.1 Providing and fixing brass stop cock of approved quality. 15 mm nominal bore.
9118.8.5 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing, jointing with one step CPVC solvent cement, cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 40 mm nominal dia pipes.
9218.8.4 CPVC pipes, concealed work, as per item above. 32 mm nominal dia pipes.
9318.8.3 CPVC pipes, concealed work, as per item above. 25 mm nominal dia pipes.
9418.8.2 CPVC pipes, concealed work, as per item above. 20 mm nominal dia pipes.
9518.8.1 CPVC pipes, concealed work, as per item above. 15 mm nominal dia pipes.
9618.17.1 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end). 25 mm nominal bore.
9718.17.2 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end). 32 mm nominal bore.
9818.17.4 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end). 50 mm nominal bore.
9918.17.4 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end). 50 mm nominal bore.
10018.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS:12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
10118.18.3 Providing and fixing ball valve (brass) of approved quality, high or low pressure, with plastic floats complete. 25 mm nominal bore (one per tank).
102C. SEPTIC TANK (2 NOS.)2.8 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m2.8.1 All kinds of soil.
1032.27 Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.
1044.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :4.1.3 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)
1055.22 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more.
1065.9 Centering and shuttering including strutting, propping etc. and removal of form for5.9.1 Foundations, footings, bases of columns, etc. for mass concrete
1075.9 Centering and shuttering including strutting, propping etc. and removal of form for5.9.3 Suspended floors, roofs, landings, balconies and access platform sqm
1085.9 Centering and shuttering including strutting, propping etc. and removal of form for5.9.13 Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards
1096.2 Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in:6.2.1 Cement mortar 1:4 (1 cement : 4 coarse sand)
1105.1 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
1116.13 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand)
11213.2 15 mm cement plaster on the rough side of single or half brick wall of mix :13.2.1 1:4 (1 cement: 4 fine sand)
11311.6 Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement.11.6.1 18 mm thick
114D. ELECTRICAL WORKS:::1.10 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.1.10.1 Group A
1151.14 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required1.14.1 a) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
1161.14 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required1.14.4 b) 2 X 6 sq. mm + 1 X 6 sq. mm earth wire
1171.14 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required1.14.11 c) 4 X 16 sq. mm + 2 X 6 sq. mm earth wire
1181.21 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. (Extra / spare conduit only – item 1.14 already includes conduit; taken as 10% of 1.5 sq.mm circuit length)1.21.1 20 mm
1191.21 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. (Extra / spare conduit only – item 1.14 already includes conduit; taken as 10% of 1.5 sq.mm circuit length)1.21.3 32 mm
1201.27 Supplying and fixing following size/modules, GI Box along with modular base and cover plate for modular switches in recess etc as required.1.27.3 4 Module (125mmX75mm)
1211.27 Supplying and fixing following size/modules, GI Box along with modular base and cover plate for modular switches in recess etc as required.1.27.4 6 Module (200mmX75mm)
1221.27 Supplying and fixing following size/modules, GI Box along with modular base and cover plate for modular switches in recess etc as required.1.27.6 12 Module (200mmX150mm)
1231.24 Supplying and fixing following modular switch/socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required.1.24.1 5/6 A switch
1241.24 Supplying and fixing following modular switch/socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required.1.24.3 15/16 A switch
1251.24 Supplying and fixing following modular switch/socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required.1.24.4 3 pin 5/6 A socket outlet
1261.24 Supplying and fixing following modular switch/socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required.1.24.5 6 pin 15/16 A socket outlet
1271.26 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.
128GI perforated cable tray 300 x 50 x 2.0 mm with cover, bends, brackets and supports - supply and fixing
12932 A 3P+N+E industrial (CEE) socket with MCB in IP67 enclosure - supply and fixing (stage / hall)
130Stage floor / wall box: 2 x 16 A power sockets, 4 XLR audio, 2 Cat-6 data - supply and fixing
1311.45 Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.
132Bajaj Energon BLDC Ceiling Fan, 1200 mm, 350 RPM
1331.35 Installation, testing and commissioning of wall bracket / ceiling fittings of all sizes and shapes containing up to two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.
13436W Cool White Bajaj LED Panel Square Light, Base Type: 2ft x 2ft
13512W Bajaj Ceiling Panel Light
136150W Bajaj LED Flood Light
1371.50.1 Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required – up to 450 mm sweep.
138Bajaj Maxima DX-G 02 150 mm Exhaust Fan
139Voltas 2 Ton 3 Star Inverter Split AC, Venus Plus (indoor + outdoor unit)
140Voltas 1.5 Ton 3 Star Inverter Split AC (indoor + outdoor unit)
141AC installation kit per unit: 3 m insulated copper piping set, drain pipe, power/control cable, outdoor bracket, labour
1422.3 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)2.3.3 12 way, Double door
1432.10 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.2.10.1 a) Single pole
1442.12 Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.2.12.1 40 A
1452.14 Supplying and fixing following rating, double pole (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.2.14.1 40 A
14612-way TPN MCB distribution board, double door, IP43, with busbars and earth bar (without MCB / isolator / RCCB)
1474-pole 63 A isolator in TPN DB, with connections
1484-pole 63 A, 30 mA RCCB in TPN DB, with connections
1493-pole 32 A \\"C\\" curve MCB in TPN DB, with connections
150Surge protection device Type-2, 40 kA, 4-pole, with backup fuse
151Havells Velora Pro 15 L storage water heater (wall mounted, 5-yr tank warranty)
152Croma 90 L 1-star single-door mini refrigerator
15343-inch 4K Smart LED TV (Samsung / LG / Sony)
154TV wall-mount bracket (tilt) with fixing
155Electric kettle 1.5 L stainless steel (Philips / Prestige)
156Wall-mounted hotel hair dryer 1600 W
15755-inch 4K Smart LED TV (Samsung / LG / Sony)
15820W LED recessed COB downlight, dimmable, 150 mm cut-out (house lights) - supply only, installation under DSR 1.35
1593W LED recessed step / aisle light, IP54, with driver - supply only, installation under DSR 1.35
160LED cove strip light 14 W/m, 24 V DC, with aluminium profile and driver
161LED exit sign with 3-hour battery backup, wall / ceiling mount - supply only, installation under DSR 1.35
162Rechargeable LED emergency light 8 W, 3-hour backup - supply only, installation under DSR 1.35
163200 W RGBW LED PAR / wash light, DMX-512, with clamp and safety wire
164300 W LED profile (ellipsoidal) spot with zoom lens and gobo holder, DMX-512
165DMX-512 lighting console, 512 channels, with flight case
166DMX dimmer / splitter pack, 12 channel, with power supply
167Stage lighting bar: 50 NB GI pipe with clamps, hanging rods and safety wires (supply and fix)
168House-light control panel (0-10 V / DALI) with 8 preset scenes and wall keypad
169JBL EON712 12-inch 1300 W powered PA speaker (Bluetooth, DSP)
170Powered 18-inch subwoofer (JBL EON718S or equal)
171Speaker wall-mount bracket / stand, power & signal cable per speaker
17232-channel digital mixing console (Yamaha TF5 / Behringer X32 or equal)
173Shure SVX24/PG58 wireless handheld microphone system
174Wireless lapel / headset microphone system (Shure SVX14 or equal)
175Shure SM58 wired dynamic vocal microphone
176Gooseneck podium microphone with base
177Stage multicore snake 24-in / 8-out, 40 m, with stage box
178Mic stands, XLR / speaker cables, connectors and equipment rack
179Laser projector 10,000 lumen WUXGA with lens and ceiling mount
180Motorised projection screen 250-inch (16:9)
181AV switching: HDMI / HDBaseT matrix, wall plates and cabling
182Addressable fire alarm control panel, 2-loop, 250 devices, with battery backup
183Addressable optical smoke detector with base
184Addressable manual call point (break-glass)
185Hooter-cum-strobe, 24 V DC
186FRLS 2C x 1.5 sq.mm shielded fire-alarm cable in conduit - supply and laying
1874 MP IP dome camera with PoE and mount
18832-channel NVR with 8 TB surveillance hard disk
18924-port PoE+ managed network switch
190Cat-6 U/UTP cable in conduit / tray - supply and laying
191Cat-6 information outlet with patch cord
192Wi-Fi 6 ceiling-mount access point
19312U wall rack with patch panel, cable managers and PDU
194Main LT panel 415 V, 250 A TPN: incomer MCCB, copper busbar, outgoing MCCBs, metering CTs, ammeter/voltmeter, MS powder-coated
195Automatic power factor correction panel 60 kVAr with detuned reactors
196Supply of 3.5C x 95 sq.mm Al. XLPE armoured 1.1 kV cable (pole -> main panel, main panel -> hall TPN DB)
197Supply of 3.5C x 35 sq.mm Al. XLPE armoured 1.1 kV cable (feeders to stage, AV, house-lighting and first-floor DB)
1987.1 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.7.1.2 Above 35 sq. mm and upto 95 sq. mm
1997.1.1 Upto 35 sq. mm
2007.7 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.7.7.2 Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)
2017.7.1 Upto 35 sq. mm (clamped with 1mm thick saddle)
2029.1 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.9.1.24 3½ X 95 sq. mm (45mm)
2039.1.21 3½ X 35 sq. mm (32mm)
20414.16.2 Supplying and laying of DWC HDPE pipe ISI marked, 90 mm dia (OD-90 mm & ID-76 mm nominal) along with accessories conforming to IS 14930 Part II, direct in ground (75 cm below GL) including excavation and refilling, for protection of underground cable.
20514.13 Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep )and re-filling etc as required14.13 a) 80 mm dia
20612.38 Supplying and fixing of light class G.I. pipe of 80 mm dia. (nominal) 3 metres length along the pole for protection of under ground cable as required.
2076.2 Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, havingsingle prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.
2086.7 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductorcomplete as required. (For horizontal run)
2096.8 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run)
2106.12 Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required
2115.4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
2125.16 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required
2135.18 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.
2145.12 Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required
2156.14 Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required
21632 A 3P+N+E industrial (CEE) socket with MCB in IP67 enclosure - supply and fixing (stage / hall)
217E. FIRE FIGHTING::Supplying and placing Eco Extinguisher 4 kg Premium ABC dry powder type fire extinguisher, red (stored pressure, IS:15683), complete with wall mounting bracket.
218Supplying and placing Agni-X 4.5 kg fire extinguisher, carbon dioxide gas, 131.56 bar testing pressure and 18 sec. discharge time, model PSS-CO2FE-4.5, complete with wall mounting bracket.
219EARTH FILLING (RAISING LOW SITE)2.38 Filling with available fly ash and earth (excluding rock) in trenches or embankment in layers (each layer should not exceed 15 cm), with intermediate layer of compacted earth (Soil density of 98%) after every four layers of compacted depth of fly ash, sides & top layer of filling shall be done with earth having total minimum compacted thickness 30 cm or as decided by Engineer -in-charge, including compacting each layer by rolling/ ramming and watering, all complete as per drawing and direction of Engineer -in - charge.
220Furniture ::Auditorium push-back tip-up seat, high-density moulded PU foam cushion, fabric upholstery, powder-coated MS frame, with arm-rests, row-seat numbering plate & floor fixing (good quality)
221Wooden veneer podium / lectern with mic & laptop provision, 600x500x1100 mm, PU polish
222Stage VIP single-seater sofa chair, hardwood frame, leatherette / fabric upholstery
223Stage dais table 1800x600x750 mm, veneered top with front skirt panel
224Stage teapoy / centre table, 600 dia x 450 mm, wood with glass top
225Green Room - dressing table 1200x450x750 mm with LED vanity mirror and drawer
226Green Room - cushioned dressing stool / chair
227Green Room - 3-seater sofa, fabric upholstered, hardwood frame
228Green Room - costume wardrobe 2-door 900x500x2000 mm, laminated board with hanging rail
229Green Room - centre table 900x600x450 mm, laminated top
230Reception counter 2400x700x1050 mm, laminate / veneer finish with granite top, drawers & CPU shelf
231High-back executive revolving chair for reception
232Visitor chair, cushioned, chrome / powder-coated legs
233Foyer lounge sofa set 3+1+1 seater, premium fabric / leatherette, hardwood frame
234Centre table + 2 side tables set, wood & glass
235Stainless-steel 3-seater waiting bench with cushioned seat
236Garden bench, FRP / cast-aluminium frame with teak-finish slats
237Stacking banquet chair, cushioned, chrome frame (multipurpose use of hall)
238Heavy-duty MS slotted-angle storage rack 5-tier, 2100x900x450 mm, powder coated
239Queen-size bed (1500x2000 mm) with hydraulic storage, engineered wood with veneer headboard
240Queen-size 8-inch pocket-spring / memory-foam mattress (premium)
241Bedside table with drawer, 450x400x500 mm
2423-door wardrobe 1800x600x2100 mm, laminated / veneered board with mirror & internal fittings
243Study / writing table 1200x600x750 mm with drawer
244Ergonomic revolving chair with arm-rest
245TV unit / console with back panel 1500x400x500 mm
246Lounge chair, cushioned, hardwood frame
247Round side table 500 dia, wood with glass top
248Dressing unit with mirror 900x450x1500 mm
249Luggage rack, wooden folding
250Guest lounge sofa set 3+2+1+1 seater, premium fabric, hardwood frame
251Centre table + 2 side tables set, wood & glass
2528-seater dining table 1800x900x750 mm, solid wood with tempered glass top
253Dining chair, cushioned, hardwood
254Crockery unit / sideboard 1500x450x900 mm
255Stainless-steel 3-seater waiting bench with cushioned seat (corridor)
256Dismantling::15.28 Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 m lead of:15.28.1 G.S. Sheet
25715.19 Dismantling steel work manually / by mechanical means in built-up sections (roof trusses) without dismembering and stacking within 50 m lead as per direction of Engineer-in-charge.
25815.14 Dismantling wood work in frames, trusses, purlins and rafters up to 10 m span and 5 m height including stacking the material within 50 m lead:15.14.1 Of sectional area 40 sq cm and above
25915.7 Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 m lead as per direction of Engineer-in-charge (walls, foundations and plinth):15.7.4 In cement mortar
26015.2 Demolishing cement concrete manually / by mechanical means including disposal of material within 50 m lead as per direction of Engineer-in-charge (floors):15.2.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)
26115.2 Demolishing cement concrete manually / by mechanical means including disposal of material within 50 m lead (foundation beds):15.2.2 Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)
26215.3 Demolishing R.C.C. work (columns, plinth beam and lintel band) manually / by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 m lead as per direction of Engineer-in-charge.
26315.6 Extra for scrapping, cleaning and straightening reinforcement from R.C.C. work.
26415.56 Dismantling old plaster or skirting, raking out joints and cleaning the surface.
26515.12 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 m lead:15.12.1 Of area 3 sq m and below
26615.12 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 m lead:15.12.2 Of area beyond 3 sq m Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58434386
AUTHORITY Government Departments
TENDER VALUE 4.84 Crore
LAST DATE 27-11-2026
Authority
Authority Name Bodoland Territorial Council
Work Description Tender for Construction Of Devnath Basumatary Guest House At Dimakuchi (G+1, 15 Rooms With Meeting Hall).
Basic Detail
Tender No 125/ACE/NIT/Infr/BTC/22-23/415
Bidding Type Tender
Location
City udalguri
State Assam
Key Dates
Publish Date 07 Nov 2026
Submission Date 27 Nov 2026
Open Date 27 Nov 2026
Finance
Tender Value 4.84 Crore
Tender Fee 9700
EMD 9.70 Lakhs
Exemption Available
Document List
2513b7ee-aa2c-4c24-9706-850f100630f1.html
BOQ_85929.xls
Tendernotice_1.pdf
Tendernotice_2.pdf
Tendernotice_3.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 07, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Nov 27, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 8 days
Nov 27, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 8 days

Tender Documents

Download All (ZIP) ↓
html

2513b7ee-aa2c-4c24-9706-850f100630f1.html

xls

BOQ_85929.xls

pdf

Tendernotice_1.pdf

pdf

Tendernotice_2.pdf

pdf

Tendernotice_3.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender