Tender For Sh-Running ,Maintenance And Operation Of Internal Electrical Installation, Compound Lighting I/C Iei Work Etc At Community Hall (Near Sainik Vihar And Rishi Nagar) Rani Bagh, Pitampura And Community Hall Shastri Nagar.
Tender Value
5.85 Lakhs
Estimated cost
Bid Submission
12 Nov 2026
5 days left
EMD
11706
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Delhi → Delhi
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Sh-Running ,Maintenance And Operation Of Internal Electrical Installation, Compound Lighting I/C Iei Work Etc At Community Hall (Near Sainik Vihar And Rishi Nagar) Rani Bagh, Pitampura And Community Hall Shastri Nagar.
BOQ
| Sl. No. | Item Description |
| 1 | Maintenance, cleaning and testing of electrical &mechanical IEI installations on weekly basis such as compound lighting and internal electrical installations as per terms & conditions and inventory enclosed by deplolying following staff. A)1 no.wireman and 1 No.khallasi-2 days in a week in general shift and as and when required for Community Hall (near SainikVihar& Rishi Nagar) Rani Bagh, Pitampura and community hall Shastrinagar. |
| 2 | Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/PVC conduit including dismantling as required. Group C |
| 3 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm |
| 4 | Rewinding of existing damaged/burnt out ceilling fan of 1200 sweep size in all respect i/c dismantling the existing fan and refixing the same with connection, testing etc complete as required. |
| 5 | LED Batten light (System lumen efficacy ≥105 <120 lm/Watt) Supplying, installation, Testing & Commissioning of LED surface mounted Batten light of following body material construction as per IS: 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range -5 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10%, P. F.20.95, IP20, CRI >80, Flicker free, (flicker should be below 5%), life time (LED, Driver & electrical circuitary), of minimum 50000 Burning Hours with, 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K/5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate (T.C.). Manufactures Word Mark/Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 Im/Watt output. LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not risę above 90°C).Powder coated die cast /Extruded aluminium Body (Thickness 1.20 mm) (A-40 watt) |
| 6 | Brush Less DIrect Current (BLDC) Motor Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal( Aluminum alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al bodyPower Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, suitable for operation with regulator for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Ceiling Fan compliant to IS 374:2019 fan Supply, earthingetc. complete as req. 1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum) |
| 7 | LED Street light fixture, powder coated pressure die cast aluminium body (System lumen efficacy ≥120 <135 lm/Watt) Supplying, installation, Testing & Commissioning of Street light LED fixture powder coated pressure die cast aluminium body with driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, freq 50/60 hz, Operating temp range -5 deg to 50 deg centigrade, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%, THD < 10% as per IEC 61000-3-2 P. F.20.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMI-EMC As per CISPR 15, lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED, Driver & electrical circuitary) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K/6500°K(As per ANSI Bin), SDCM(Standard Deviation Color Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output. LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement.(Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). (A 120 watt)Installation, Testing, Commissioning and replacing at the place of old existing fan i/c dismantling and rebate for dismentalled material. |
| 8 | Supply and fixing of following electrical wiring from deputed labour accessories i/c connection, testing etc complete as required. |
| 9 | 3 mm thick phenolic laminated sheet |
| 10 | 5/6 amp one way switch piano type ISI marked |
| 11 | 15/16 amp one way switch piano type ISI marked |
| 12 | 3 pin 5/6 amp socket outlet piano type ISI marked |
| 13 | 6 pin 15/16 A & 5/6A socket outlet Piano type ISI marked |
| 14 | Supplying and drawing of FRLS/HFFR PVC insulated single core copper condutor cable in the existing surface/receses, steel/PVC conduit |
| 15 | 1.5 sq. mm ISI marked,FRLS/HFFR PVC insulated single core copper condutor cable |
| 16 | 2.5 sq. mm ISI marked,FRLS/HFFR PVC insulated single core copper condutor cable |
| 17 | 4 sq. mm ISI marked,FRLS/HFFR PVC insulated single core copper condutor cable |
| 18 | Supplying and fixing of 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\"curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete i/c with connections, testing and commissioning etc. as required |
| 19 | Single pole |
| 20 | Double Pole |
| 21 | Lifting out of the existing submersible pump set from the existing bore well i/c dismantling the pipe line and pump set &submersible cable with the help of tri post block etc. as required. |
| 22 | Lowering the submersible pump set after repairing the pump set in the existing bore well i/c making of connection of pump set and pipe line providing with rubber packing & nut bolts, making of water proof joint of submersible cable, testing commissioning etc. as required. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 12, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysNov 13, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender