Tender For Repair/Maint Of Overhead Tanks,Cleaning Of Sedimentation Tanks,Ug Sump,Borewell,Motors,Pumps Motor Control Panel Including Certain Other Connected Works At Water Supply Installation And Repair/Maintenance Of Orp Water Filters,Chemical Dosi
Tender Value
39 Lakhs
Estimated cost
Bid Submission
27 Nov 2026
20 days left
EMD
78000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Tinsukia → Assam
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair/Maint Of Overhead Tanks,Cleaning Of Sedimentation Tanks,Ug Sump,Borewell,Motors,Pumps Motor Control Panel Including Certain Other Connected Works At Water Supply Installation And Repair/Maintenance Of Orp Water Filters,Chemical Dosing System ,Control Cable,Valve Pits Alongwith Certain Other Connected Works At Mil Stn Lekhapani Under Ge Dinjan No.2
BOQ
| Sl. No. | Item Description |
| 1 | Material and labour for taking out existing unserviceable/burnt out electric monoblock motor/pumpset of capacity 10 HP, 440 Volts, 50 Hz from the existing foundation by disconnecting all electrical and mechanical connections, removing terminal/cable connections, coupling and other connected fittings, dismantling the motor as required, shifting the same to suitable repair/workshop area and opening the motor/pump for inspection of stator, rotor shaft, windings, bearings, impeller, Mounting / Volute casing, shaft sleeve, mechanical seal and other internal components for repair/replacement as required and re-assembling the serviced motor/pumpset with the repaired / rewound 10HP motor, including refitting of all serviceable components like bearing, impeller, casing etc. complete alongwith tightening of nut, bolts and washers, alignment of motor and pump, connection of electrical and mechanical accessories and making the complete monoblock pump set ready for operation complete all as specified and directed by Engineer-in-Charge. Note: (i) All replaced spare parts / materials required for motor/pump shall be measured and paid separately here-in-after under another item as 'supply only'.(ii) Work for rethreading/grinding/metal surfacing and fabrication works to pump or rotor shaft shall be measured & paid separately under respective items. |
| 2 | Material and labour for removal of completely burnt/unserviceable winding from the stator of dismantled 10 HP, 440 Volts, 50 Hz motor, cleaning of stator slots, examination of stator core and carrying out complete rewinding with approved quality super-enamelled copper winding wire of suitable size and specification, including provision and fixing of required slot insulation, insulating sleeves, inter-coil insulation, slot wedges and other minor insulating materials, making of all coil and terminal connections, application of approved insulating varnish, baking/curing etc. and carrying out necessary electrical tests to obtain satisfactory result complete all as specified and directed by Engineer-in-Charge. |
| 3 | Material and labour for taking out existing unserviceable/burnt out electric monoblock motor/pumpset of capacity 20 HP, 440 Volts, 50 Hz from the existing foundation by disconnecting all electrical and mechanical connections, removing terminal/cable connections, coupling and other connected fittings, dismantling the motor as required, shifting the same to suitable repair/workshop area and opening the motor/pump for inspection of stator, rotor, windings, bearings, impeller, Mounting / Volute casing, shaft sleeve, mechanical seal and other internal components for repair/replacement as required and re-assembling the serviced motor/pumpset with the repaired / rewound 20HP motor, including refitting of all serviceable components like bearing, impeller, casing etc. complete alongwith tightening of nut, bolts and washers, alignment of motor and pump, connection of electrical and mechanical accessories and making the complete monoblock pump set ready for operation complete all as specified and directed by Engineer-in-Charge. Note: (i) All replaced spare parts / materials required for motor/pump shall be measured and paid separately here-in-after under another item as 'supply only'.(ii) Work for rethreading/grinding/metal surfacing and fabrication works to pump or rotor shaft shall be measured & paid separately under respective items. |
| 4 | Material and labour for removal of completely burnt/unserviceable winding from the stator of dismantled 20 HP, 440 Volts, 50 Hz motor, cleaning of stator slots, examination of stator core and carrying out complete rewinding with approved quality super-enamelled copper winding wire of suitable size and specification, including provision and fixing of required slot insulation, insulating sleeves, inter-coil insulation, slot wedges and other minor insulating materials, making of all coil and terminal connections, application of approved insulating varnish, baking/curing etc. and carrying out necessary electrical tests to obtain satisfactory result complete all as specified and directed by Engineer-in-Charge. |
| 5 | Material and labour for repair of rotor shaft for 10 HP motor through remetalling of surface/re-threading/re-grinding and fabrication job on rotor shaft in workshop or on lathe work as required including providing gland packing and grease of approved grade suitably and re-fitting properly to their original location including testing to get satisfactory result complete all as specifed and as directed by Engr-in-charge. |
| 6 | Material and labour for repair of rotor shaft for 20 HP motor through remetalling of surface/re-threading/re-grinding and fabrication job on rotor shaft in workshop or on lathe work as required including providing gland packing and grease of approved grade suitably and re-fitting properly to their original location including testing to get satisfactory result complete all as specifed and as directed by Engr-in-charge. |
| 7 | Supply only single metal impeller made of cast iron for 10 HP monoblock pump set of model KDS-1050+ or as per existing sample complete all as specified and directed by Engineer-in-Charge |
| 8 | Supply only single metal impeller made of cast iron for 20 HP monoblock pump set of model KDS-2050+ or as per existing sample complete all as specified and directed by Engineer-in-Charge |
| 9 | Supply only double metal impeller (1st stage) made of cast iron for 20 HP monoblock pump set of model KDT-2070+ or as per existing sample complete all as specified and directed by Engineer-in-Charge |
| 10 | Supply only double metal impeller (2nd stage) made of cast iron for 20 HP monoblock pump set of model KDT-2070+ or as per existing sample complete all as specified and directed by Engineer-in-Charge |
| 11 | Supply only ball bearing of 6308 including taking out/dismantling old unserviceable one from pumpset complete all as specified and directed by Engineer-in-Charge. |
| 12 | Supply only ball bearing of 6307 including taking out/dismantling old unserviceable one from pumpset complete all as specified and directed by Engineer-in-Charge |
| 13 | Supply only rotor fitted shaft as per existing sample for 10 HP monoblock pumpset complete all as specified and directed by Engineer-in-Charge |
| 14 | Supply only rotor fitted shaft as per existing sample for 20 HP monoblock pumpset complete all as specified and directed by Engineer-in-Charge. |
| 15 | Supply only mounting casing for pump model KDS-1050+ of 10 HP monoblock pump as per existing sample complete all as specified and directed by Engineer-in-Charge |
| 16 | Supply only mounting casing for pump model KDS-2050+ / KDT-2070+ of 20 HP monoblock pump as per existing sample complete all as specified and directed by Engineer-in-Charge |
| 17 | Supply only volute casing for pump model KDS-1050+ of 10 HP monoblock pump as per existing sample complete all as specified and directed by Engineer-in-Charge |
| 18 | Supply only volute casing for pump model KDS-2050+ / KDT-2070+ of 20 HP monoblock pump as per existing sample complete all as specified and directed by Engineer-in-Charge |
| 19 | Supply only shaft sleeve set for pump model KDS-1050+ of 10 HP monoblock pump as per existing sample complete all as specified and directed by Engineer-in-Charge |
| 20 | Supply only shaft sleeve set for pump model KDS-2050+ / KDT-2070+ of 20 HP monoblock pump as per existing sample complete all as specified and directed by Engineer-in-Charge |
| 21 | Supply only mechanical seal for pump model KDS-1050+ of 10 HP monoblock pump as per existingsample complete all as specified and directed by Engineer-in-Charge |
| 22 | Supply only mechanical seal for pump model KDS-2050+ / KDT-2070+ of 20 HP monoblock pump as per existing sample complete all as specified and directed by Engineer-in-Charge |
| 23 | M&L for Taking up electric driven submersible motor & pump set of capacity 7.5 to 15 HP from bore well complete with column pipe upto submersible depth by using chain pulley and allied T&P required taking the motor & pumpset to the work shop for repair work by dismantling all the parts of submersible pumps set complete with submersible motor, 3 phase 50 hz, 415 volts AC, of capacity 7.5HP to 15 HP capacity, checking all parts, segragating the serviceable parts for reuse, removing the defective parts and repair / replace the same (as described below)including re-assembling, connections and testing complete and after repair, lowering the same pumset alongwith column pipes etc. in the same existing bore well, making all the electrical connections complete with submersible cable including commissioning, testing complete on full load to the entire satisfaction of Engr-in-charge. Note: Spare required shall be measured and paid as 'supply only' rate under relevant items of this schedule. |
| 24 | Material and labour for complete rewinding of existing burnt/unserviceable 15 HP submersible motor after dismantling of the motor, including removal of old burnt winding, cleaning of stator slots and stator core, checking the condition of stator core and other internal components, provision and insertion of approved quality suitable size super-enamelled/waterproof submersible-grade copper winding wire, including required slot insulation, insulating sleeves, liners, separators, wedges and other approved insulating materials, making all coil-to-coil and lead connections with proper insulation, application of approved insulating varnish/resin suitable for submersible motor, curing/baking as applicable, sealing and insulation treatment of winding, refitting of winding leads and terminal connections, and carrying out necessary electrical tests to obtain satisfactory result, complete all as specified and directed by Engineer-in-Charge |
| 25 | Supply only thrust bearing for 15 HP submersible pumpset complete all as specified and directed by Engineer-in-Charge |
| 26 | Supply only bearing housing for 15 HP submersible pumpset complete all as specified and directed by Engineer-in-Charge |
| 27 | Supply only rotor fitted shaft for 15 HP submersible pumpset complete all as specified and directed by Engineer-in-Charge |
| 28 | Supply only steel sand guard for 15 HP submersible pumpset complete all as specified and directed by Engineer-in-Charge |
| 29 | Supply only mechanical seal for 15 HP submersible pumpset complete all as specified and directed by Engineer-in-Charge |
| 30 | Supply only flat three core pvc insulated & pvc sheathed industrial cable of copper conductor of size 6sqmm x 3core for submersible pump-motors 1100 Volt, conforming to IS 694 complete all as specified and directed by Engineer-in-Charge |
| 31 | Material and labour for complete rewinding of existing burnt/unserviceable 7.5 HP submersible motor after dismantling of the motor, including removal of old burnt winding, cleaning of stator slots and stator core, checking the condition of stator core and other internal components, provision and insertion of approved quality suitable size super-enamelled/waterproof submersible-grade copper winding wire, including required slot insulation, insulating sleeves, liners, separators, wedges and other approved insulating materials, making all coil-to-coil and lead connections with proper insulation, application of approved insulating varnish/resin suitable for submersible motor, curing/baking as applicable, sealing and insulation treatment of winding, refitting of winding leads and terminal connections, and carrying out necessary electrical tests to obtain satisfactory result, complete all as specified and directed by Engineer-in-Charge |
| 32 | Supply only thrust bearing for 7.5 HP submersible pumpset complete all as specified and directed by Engineer-in-Charge |
| 33 | Supply only bearing housing for 7.5 HP submersible pumpset complete all as specified and directed by Engineer-in-Charge |
| 34 | Supply only mechanical seal for 7.5 HP submersible pumpset complete all as specified and directed by Engineer-in-Charge |
| 35 | Supply & fix cheminject chemical dozing pump 200 LPH @ 05 Kg pressure electro-mechanical, diaphragm type P P liquid head with accessories like NRV, Foot valve / Y-Strainer, suction / discharge tube fitted with 0.5 HP, 440V AC , 1440 RPM with flange mounted motor of model model RM-14 including taking down old u/s complete all as specified and directed by Engineer-in-Charge |
| 36 | Material and labour for taking out old unserviceable burnt out electric monoblock motor with pump from the foundation of pump capacity 2 HP, 440 Volts, 50 Hz by opening/disconnecting all mechanical and electrical connections and transporting to nearest work shop and rewinding the same by using approved make super enamelled insulation copper wire of suitable insulation class of approriate size after pulling out burnt out copper wires from the slots of stator including replacement of minor accessories etc.including varnishing/heating at heat chamber suitably and opening the monoblock pump assembly for replacement of unserviceable parts, servicing by grease , maintenance and reassembling all as per existing complete and taking back the whole pump sets to its original location and fixed or placed suitably including making the electrical and pipe connections including testing to get satisfactory result complete all as specified and directed by Engineer-in-Charge |
| 37 | Description all as per item No 36 here-in-before but for 0.5 HP / 0.37 KW motor complete all as specified and directed by Engineer-in-Charge |
| 38 | Supply and fixing in repair water pressure gauge of suitable dia as per existing sample with dial measuring 0 TO 14 Kg/Sq cm including reqd clamps, nuts, bolts & washers complete all as specified and directed by Engineer-in-Charge.. |
| 39 | Suraface dressing not exceeding 15cm deep, getting out soft / loose soil (including site clearance and removing unwanted bushes) and making smooth surface complete all as specified and directed by Engineer-in-Charge |
| 40 | Material and Labour for Cement concrete (1:3:6) type C-2 using 40mm graded crushed stone aggregate as in foundation etc complete all as specified and directed by Engineer-in-Charge |
| 41 | Material and Labour for Cement concrete (1:4:8) type D-2 using 40mm graded crushed stone aggregate as in mass concrete, sub base etc complete all as specified and directed by Engineer-in-Charge |
| 42 | Material & Labour for cleaning & washing of JACK WELL of dia 4.60 metre and depth 10 meter after complete pumping out of dirty water / sludge from the static tank (Pumpset is own arrangement of the contractor) by making preparatory arrangement and taking out deposited sludge, soils etc from the bottom including cleaning of inside walls with steel wire brush, gunny bags, etc and washing/ cleaning and removing sludge, soil, etc. to a distance not exceeding 50 meter from the pump house campus and deposited where directed complete including writing the words \\"Date Cleaned on\\" on the Front/Road side face complete all as specified and directed by Engineer-in-Charge |
| 43 | Material & Labour for cleaning/washing sedimentation tank of capacity 20000 Gallons after complete pumping out of dirty water / sludge from the static tank (Pumpset is own arrangement of the contractor) by making preparatory arrangement and taking out deposited sludge, soil etc. from the bottom including cleaning of inside walls / RCC channels with steel wire brush, gunny bags, etc and washing/cleaning and removing sludge, soils etc to a distance not exceeding 50 metre from the pump house campus area, and deposited where directed complete including writting the words \\"Date Cleaned on\\" on the Front/Road side face complete all as specified and directed by Engineer-in-Charge |
| 44 | Material & Labour for cleaning/washing Lamella clarifier plant (comprising of 01xFlocculation tank, 04xchemical dosing chambers and 01xLamella settling plates tank) of tank capacity / discharge 80000 litre/hour including cleaning of the each inclined settling plates of the clarifier plant by making preparatory arrangement and taking out deposited sludge, soil etc. from the bottom including cleaning inside walls of complete plant with steel wire brush, gunny bags, etc and washing/cleaning and removing sludge, soils etc to a distance not exceeding 50 metre from the pump house campus area, and deposited where directed complete including writting the words \\"Date Cleaned on\\" on the Front/Road side face and including internal painting of complete plant with two coats of primer of red oxide / zinc chrome and one coat of black bituminous paint for the complete inner surface of plant complete all as specified and directed by Engineer-in-Charge |
| 45 | Material & Labour for cleaning/washing of Ground level storage sump of 20000 gallons capacity after complete pumping out of water from the static tank (Pumpset is own arrangement of the contractor) and removing all dirts/sludge by scraping with steel wire brush/ gunny bags cleaning/ washing thoroughly floor and inner walls with bleaching powder solution and removing sludge/soils etc. to a distance not exceeding 50 metre from pump house campus, including writting the words \\"Date Cleaned on\\" on the Front/Road side face complete all as specified and directed by Engineer-in-Charge |
| 46 | Material & Labour for cleaning/washing of Ground level storage sump of 50000 gallons capacity after complete pumping out of water from the static tank (Pumpset is own arrangement of the contractor) and removing all dirts/sludge by scraping with steel wire brush/ gunny bags cleaning/ washing thoroughly floor and inner walls with bleaching powder solution and removing sludge/soils etc. to a distance not exceeding 50 metre from pump house campus, including writting the words \\"Date Cleaned on\\" on the Front/Road side face complete all as specified and directed by Engineer-in-Charge |
| 47 | Material & Labour for cleaning/washing of RCC Overhead Tank 50000 Gallon capacity, 50 feet high staging after complete dewatering and removal of all dirts/sludge/silts etc. by scraping with steel wire brush/gunny bags, cleaning/washing thoroughly floor and all-over the inner walls with bleaching powder solution and drained/washed out including necessary scaffolding works including writting the words \\"Date Cleaned on\\" on the Front/Road side face complete all as specified and directed by Engineer-in-Charge |
| 48 | Material & Labour for cleaning/washing pressed steel Overhead Tank 9600 gallons capacity, 12.00 meter high staging after complete dewatering and removal of all dirts/ sludge by scraping with steel wire brush/ gunny bags, washing thoroughly floor and inner walls and draining/ washed out before fresh water filled including writting the words \\"Date Cleaned on\\" on the Front/Road side face of pressed steel OH Tank including necessary scaffolding works complete all as specified and directed by Engineer-in-Charge |
| 49 | Material and labour for cleaning and removing all scales,silts,mud and dust, dirts etc. from RCC service water tank manually and cleaning, scraping inner surfaces of tank by means of wire brush and then washing with clean water and cleaning of mouths of circulating pipes etc. and thoroughly washed with clean water of capacity of tank exceeding 500 litres but not exceeding 1000 litres including writing date of cleaning on outer body of the tank with 100mm high by synthetic enamel paint (white/black colour) complete all as specified and directed by Engineer-in-Charge |
| 50 | Descrption all as per Item no 49 here-in-before but capacity of RCC water tank exceeding 1000 litres but not exceeding 2000 litres complete all as specified and directed by Engineer-in-Charge |
| 51 | Material and labour for cleaning and removing all scales,silts,mud and dust, dirts etc. from PVC service water tank manually and cleaning, scraping inner surfaces of tank by means of soft brush and then washing with clean water and cleaning of mouths of circulating pipes etc.of capacity of tank exceeding 500 litres but not exceeding 1000 litres including writing date of cleaning on outer body of the tank with 100mm high by synthetic enamel paint (white/black colour) complete all as specified and directed by Engineer-in-Charge |
| 52 | Descrption all as per Item no 51 here-in-before but capacity of PVC water tank exceeding 250 litres but not exceeding 500 litres complete all as specified and directed by Engineer-in-Charge |
| 53 | Supply & fixing mild steel Fe 410 -W (Gde- E- 250) quality- A Fe angle iron as in angle, channel, tee-scetion, tie bar, cross arm, bracing, I-section etc. as required and directed including making necessary holes through drilling/ welding/ cutting work for fixing of TMT round bars, nuts, bolts and washers complete and painting with two coats of synthetic enamel paint of approved colour over a coat of red oxide / zinc chrome primer complete including dismantling old old rusted structural sections complete all as specified and directed by Engineer-in-Charge |
| 54 | Supply and fixing TMT bars 12 to 16 mm dia and over, cut to length, bent to shape required, including welding (SMAW / GMAW /MIG etc.) work complete with structural steel sections like angle, channels, beams etc complete and painting with two coats of synthetic enamel paint of approved colour over a coat of red oxide / zinc chrome primer complete including dismantling old rusted TMT bars etc complete all as specified and directed by Engineer-in-Charge |
| 55 | Supply and fixing mild steel machine made nuts, bolts and washers etc. dia of 16 to 20 mm or as required on site for fixing of various structural steel sections like angle, channels, plate, etc. complete including dismantling old rusted nuts, bolts, washers etc.complete all as specified and directed by Engineer-in-Charge |
| 56 | Material and labour for painting of existing LT panel enclosure by spray application, including complete isolation of the panel from electrical supply and protection/removal as necessary of voltmeters, selector-switches, indicating lamps, contacor & relays, motor starters, cables, cable glands, labels and other electrical accessories; removal of loose/peeling paint, rust, dirt, grease and other foreign matter from all accessible external metal surfaces by scraping, wire brushing, emery paper and suitable cleaning/degreasing solvent; preparation of sound and clean surface; application of one coat of approved compatible metal primer by spray gun followed by two coats of approved synthetic enamel/PU paint of specified shade and colour by spray application, including necessary masking and protection, thinner/solvent, spray gun, compressor, brushes and other consumables, labour, T&P, cleaning after completion and all incidental charges, complete all as specified and directed by Engineer-in-Charge (Note:- Painting shall be restricted to external accessible metal surfaces only. Electrical components, terminal connections, name plates and other functional components shall be suitably protected and shall not be obstructed by paint.) |
| 57 | Material and labour for external painting of existing 20mm to 250mm dia CI/DI/GI water supply pipe lines including showing flow direction by arrow marked at any location,including painting of connected flanges, bends and other integral fittings etc. complete with removal of loose / peeling paint, rust, dirt, grease and other foreign matter by scraping, wire brushing and cleaning, preparation of sound external surface, after application of one coat of red oxide / zinc chrome primer as metal primer and two coats of synthetic enamel paint of approved colour and shade as directed complete alongwith masking/protection of valves, instruments like pressure gauges and other components etc., including primer, paint, thinner, emery paper, wire brushes, brushes/spray equipment, labour, T&P, ladder/scaffolding wherever required, wastage and all incidental charges, complete all as specified and as directed by Engineer-in-Charge. |
| 58 | Material and labour for painting of existing electric motor of capacity 10HP to 20HP complete, including isolation and protection of motor from electrical supply, cleaning and preparation of accessible external metal surfaces by wire brushing, scraping and removal of loose paint, rust, dirt, grease and other foreign matter, after application of one coat of red oxide / zinc chrome primer as metal primer and two coats of synthetic enamel paint of approved colour and shade as directed,including painting of motor body, end covers and other accessible external metal surfaces, with proper masking/protection of terminal box, cable entry, name plate, ventilation openings, shaft, bearings and other components not intended for painting, including thinner, brushes, rollers, wire brushes, emery paper, cleaning materials, labour, T&P and all incidental charges, complete all as specified and as directed by Engineer-in-Charge. (Note:- One complete motor of the specified capacity as mentioned above, satisfactorily prepared and painted, shall constitute as one job only.) |
| 59 | Supply, installation and fixing of 6 kg capacity ABC Dry Chemical Powder type, stored-pressure fire extinguisher, Secure Guard make or approved equivalent, ISI marked and conforming to the latest applicable requirements of IS 15683, complete in all respects with factory-filled ABC dry chemical extinguishing powder suitable for Class A, Class B and Class C fires, pressurised with suitable expellant gas, complete with mild-steel fire-extinguisher cylinder/body, squeeze-grip type operating valve/handle assembly, safety pin and tamper/seal arrangement, discharge hose with nozzle,carrying/operating handle, wall mounting hook/bracket with necessary screws and fixing accessories, operating/instruction manual and ready for immediate use complete all as specified and as directed by Engineer-in-Charge. |
| 60 | Materials & labour for earthing complete with galvanized earth plate electrode 600 x 600 x 6.0 mm thick, buried directly in ground (earth pit not less than 2.25 m deep below normal ground level ) with top edge of the plate not less than 1.5 m below normal ground level, connected to GI strip of size 32x6 mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel, earth strip protected by and including 40mm dia GI pipe(light grade), alternate layers of charcoal and salt, including 20 mm bore GI tubing for watering to earth electrode, earth strip connected to test point/ distribution panel /feeder pillar etc as directed including necessary earth work, concrete pit with PCC (1:3:6) type C1, pre cast RCC(1:1:5:3) type A1 cover slab duly reinforced with 8 mm dia TMT bar 150mm c/c both way and two numbers lifting handle made of TMT bar and set in cement mortar (1:4), funnel, wire mesh, all as shown in electrical plate No 3 of SSR part-1 and testing on completion including taking out old earthing complete all as specified and directed by Engineer-in-Charge |
| 61 | M&L for earth continuity conductor fixed to wall on batten or recess or buried in ground or fixed to panels or any other indicated situated for loop earthing etc. as required in length of GI earth strip of size 32x6mm complete all as specified and as directed by Engr-in-Charge. |
| 62 | Supply & fix in repair MCCB 4 pole, 415 volt,adjustable type 200 amps operated with breaking capacity of 36KA of make L&T D-sine complete all as specified and directed by Engineer-in-Charge |
| 63 | Supply & fix in repair MCCB 4 pole, 415 volt, fixed type 63 amps front/knob operated with breaking capacity of 16KA complete all as specified and directed by Engineer-in-Charge |
| 64 | Supply & Fixing of fully automatic star delta starter sheet metal enclosure suitable for 10 HP motor , 440 volt, 3 Ph Elect Motor with Single Phase Protection and motor protection relay feature conforming to IS / IEC -60947 after taking down old unserviceable one and fixed to the same location by making electrical connection properly complete all as specified and directed by Engineer-in-Charge |
| 65 | Supply & Fixing of fully automatic star delta starter sheet metal enclosure suitable for 20 HP motor , 440 volt, 3 Ph Elect Motor with Single Phase Protection and motor protection relay feature conforming to IS / IEC-60947 after taking down old unserviceable one and fixed to the same location by making electrical connection properly complete all as specified and directed by Engineer-in-Charge |
| 66 | Dismantling and removing burnt out contactor and Supply and fixing Contactor 3-Pole with AC Coil, 415 Volt, 50 Hz, conforms to IS / IEC 60947-4-1, Type- MNX 18 of make Lauritz & Kundsen or as per existing sample complete all as specified and directed by Engineer-in-Charge |
| 67 | Dismantling and removing burnt out contactor and Supply and fixing Contactor 3-Pole with AC Coil, 415 Volt, 50 Hz, conforms to IS / IEC 60947-4-1, Type- MNX 25 of make Lauritz & Kundsen or as per existing sample complete all as specified and directed by Engineer-in-Charge. |
| 68 | S & F in repair Thermal Overload Relay with built-in single phasing protection for 3-phase motor with thernmal OL range 14-23 A conforms to IS / IEC 60947-4-1, suitable for 10 to 20HP, 415 V, 3 Phase Motor Starter of make Lauritz & Kundsen or as per existing sample complete all as specified and directed by Engineer-in-Charge |
| 69 | Supply and fix in repair Electronic motor protection relay with built in single phase preventer, current unbalance, earth fault & protection against phase sequence reversal and overload etc. of model eMPR300 of make Lauritz & Kundsen or as per existing sample suitable for 10 to 20 HP motor complete all as specified and directed by Engineer-in-Charge. |
| 70 | Supply & fix 3 Phase Dgitial Panel voltmeter Meter Flush Mounting 96x96mm, Accuracy Class -1 , Input Voltage measurement range 50-500V AC including taking down existing unserviceable one complete all as specified and directed by Engineer-in-Charge |
| 71 | Supply & fix 3 Phase, 5A, Dgitial Panel Ammeter Flush Mounting 96x96mm, Accuracy Class -1 ,CT/PT Site programmable including taking down existing unserviceable one complete all as specified and directed by Engineer-in-Charge |
| 72 | Supply & fix 3 Phase LED indicator lamp R/Y/B as per requirements on site including taking down old unserviceable lamp complete all as specified and directed by Engineer-in-Charge |
| 73 | Supply & fix in replacement of gland packing for monoblock motor or sluice valve for any capacity complete all as specified and directed by Engineer-in-Charge. |
| 74 | Supply and fix in repairs 100mm dia mettallic cast iron foot valve at the end of GI pipe/PVC pipe with complete fixing accessories under jackwell/river complete all as specified and directed by Engineer-in-Charge. |
| 75 | Dismantling and taking down existing pressed steel bottom plates of size 1.22 mtr x 1.22 mtrx 6mm or side plates of size 1.22mtrx1.22 mtrx5mm thick as directed from 9600 gallons capacity steel Overhead tanks on 12 metre high staging carefully without damaging other members after unscrewing bolts, nuts,washers etc and separating serviceable plates and keep in safe custody for reuse at site complete all as specified and directed by Engineer-in-Charge |
| 76 | Supply, erection, hoisting and fixing of new pressed steel bottom plates of size 1.22mx 1.22mx 6mm thick (with necessary jointing materials) made to required shape, drilling necessary holes for fixing bolts, nuts & washers including provision of proper arrangement of jointing by lead joint / lead wool / black putty in between plates as required at site & fixed these to existing serviceable plates of PS overhead water tank at 12 mtr high staging complete all as specified and directed by Engineer-in-Charge |
| 77 | Supply, erection, hoisting and fixing of new pressed steel bottom plates of size 1.22mx 1.22mx 5mm thick (with necessary jointing materials) made to required shape, drilling necessary holes for fixing bolts, nuts & washers including provision of proper arrangement of jointing by lead joint / lead wool / black putty in between plates as required at site & fixed these to existing serviceable plates of PS overhead water tank at 12 mtr high staging complete all as specified and directed by Engineer-in-Charge |
| 78 | Fixing only old serviceable pressed steel side plates of size 1.22mx1.22mx5mm & bottom plates of size 1.22mx1.22mx6mm thick (with necessary jointing materials) made to required shape, making necessary holes through drilling for fixing ofnuts, bolts & washers including provision of proper arrangement of jointing by lead joint / lead wool / black putty in between plates as required at site & fixed these to existing plates of PS overhead water tank at 12 mtr high staging complete all as specified and directed by Engineer-in-Charge |
| 79 | Repairs to damaged portion of pressed steel tank plates for 9600 Gallons PS Overhead Tank (12 mtr high) of existing gauge and size by means of welding over the hole upto 20mm dia with new Mild Steel plate of size 15 cm x 15 cmx6mm thick on the inner side of PS tank and testing complete all as specified and directed by Engineer-in-Charge |
| 80 | Dismantling of rusted angle iron as bracing, cross-arms, tie bar, I-section etc. from Pressed Steel overhead Tank on 12 meter high staging by unscrewing nuts, bolts and washers etc complete all as specified and directed by Engineer-in-Charge |
| 81 | Supply, erection, hoisting and fixing of mild steel top sheet / roof sheet 3.15 mm thick made to required shape by making necessary holes through drilling for fixing of nuts, bolts & washers and fixed to existing roof sheet by welding etc. as required on work site of pressed steel overhaed water tank on 12 metre high staging including dismantling/taking down existing unserviceable top sheets complete all as specified and directed by Engineer-in-Charge |
| 82 | Fixing only serviceable nuts, bolts and washers of appropriate length and of dia 16 to 20 mm as required on site for fixing of steel plate, sheets, various structural steel scetions etc. complete all as specified and directed by Engineer-in-Charge |
| 83 | Supply and fix mild steel machine made of nuts, bolts and washers etc of appropriate length and dia of 16 to 20 mm as required on site for fixing of steel plate, sheets, various structural steel scetions etc. complete all as specified and directed by Engineer-in-Charge |
| 84 | Material and labour for preparing internal surfaces of PS over head tank, of cuboid shape of dimension (l=4.88m, b=3.66m & h=2.44m) on 12 mtrs high staging of 9600 gallons capacity, over 10 cm width or girth, scraping with steel wire brushes and applying with two coats of black bituminous paint ( suitable for drinking water purpose) over a coat of red oxide / zinc chrome primer complete all as specified and directed by Engineer-in-Charge. |
| 85 | Material and labour for preparing external surfaces of PS over head tank, of cuboid shape of dimension ( l=4.88m, b=3.66m & h=2.44m) including PS OHT rising pipe of (dia d=0.1m & height h=14.8m), delivery pipe of (dia d=0.1m & height h=12.3m), overflow pipe of (dia d=0.1m & height h=14.5m), washout pipe of (dia d=0.08m & height h=8.3m) by maintaining approved colour codes for above four pipelines as per MES norms and regulations and also preparing external surfaces of structural steel sections like (a). MS Angle of dimension (65mmx65mmx6mm) of length 4.10m of total qty 32 Nos. (b). MS Angle of dimension (65mmx65mmx6mm) of length 3.50m of total qty 24 Nos. (c). MS Angle of dimension (150mmx150mmx12mm) of length 12m of total qty 4 Nos. (d). MS I-section of dimension (100mmx150mmx100mm) of length 3.66m of total qty 2 Nos. (e). MS I-section of dimension (100mmx150mmx100mm) of length 4.88m of total qty 4 Nos. all complete on 12 mtrs high staging over 10 cm width or girth, scraping with steel wire brushes and applying two coats of aluminium paint (over complete external surfaces of PS overhead tank including complete staging structure from foundation) over a coat of red oxide / zinc chrome primer, complete all as specified and directed by Engineer-in-Charge. |
| 86 | M & L for construction of valve chamber of internal size 120cm x 120cm x 90cm with 23 cm thick wall in CM 1:6 including excavation, earth work in any type of strata / soil & PCC 1:4:8 foundation type D-2, 75 mm thick including 25 mm thick PCC 1:2:4 type B1 in & plastering the internal surface with 10 mm thick cement mortar 1:4 providing 3.15 mm MS sheet chamber cover double opening arrangement center lock system with 40x40x5mm angle iron frame duly painted with two coat of black bituminous paint over one coat of red oxide primer and finishing exposed faces of concrete surfaces and plaster surfaces with three coats of white wash including dismantling the existing unserviceable valve pit complete all as specified and directed by Engineer-in-Charge |
| 87 | M & L for construction of valve chamber of internal size 90cm x 90cm x 90cm with 23 cm thick wall in CM 1:6 including excavation, earth work in any type of strata / soil & PCC 1:4:8 foundation type D-2, 75 mm thick including 25 mm thick PCC 1:2:4 type B1 in & plastering the internal surface with 10 mm thick cement mortar 1:4 providing 3.15 mm MS sheet chamber cover double opening arrangement center lock system with 40x40x5mm angle iron frame duly painted with two coat of black bituminous paint over one coat of red oxide primer and finishing exposed faces of concrete surfaces and plaster surfaces with three coats of white wash including dismantling the existing unserviceable valve pit complete all as specified and directed by Engineer-in-Charge |
| 88 | Supply and fixing Water Supply Distribution System Single Line Diagram Board of size 6 feet × 4 feet,digitally / UV printed on Aluminium Composite Panel (ACP) sheet of minimum 3 mm thickness, with approved site-specific water supply distribution single line diagram showing source/pump house, pump sets, storage tanks, filteration plant, main and branch pipelines with sizes, valves, flow directions and distribution areas etc. including protective lamination/finish over the ACP sheet and securely mounted on a fabricated MS angle framework comprising MS angles, channels etc. alongwith suitable intermediate horizontal and vertical stiffeners, supported on independent MS angle vertical members including MS bolts, nuts, washers and all necessary structural supports; including cutting, welding, drilling, grinding, fabrication, erection, fixing of ACP panel with suitable SS screws/rivets with one coat of approved red oxide / zinc chrome primer and two coats of approved synthetic enamel paint to all exposed MS surfaces complete all as specifoed and as directed by the Engineer-in-Charge. |
| 89 | Supply and fixing Water Supply Distribution System Single Line Diagram Board of size 4 feet × 3 feet,digitally / UV printed on Aluminium Composite Panel (ACP) sheet of minimum 3 mm thickness with approved site-specific water supply distribution single line diagram showing source/pump house, pump sets, storage tanks, filteration plant, main and branch pipelines with sizes, valves, flow directions and distribution areas etc. including protective lamination/finish over the ACP sheet and securely mounted on a fabricated MS angle framework comprising MS angles, channels etc. alongwith suitable intermediate horizontal and vertical stiffeners, supported on independent MS angle vertical members including MS bolts, nuts, washers and all necessary structural supports; including cutting, welding, drilling, grinding, fabrication, erection, fixing of ACP panel with suitable SS screws/rivets with one coat of approved red oxide / zinc chrome primer and two coats of approved synthetic enamel paint to all exposed MS surfaces complete all as specifoed and as directed by the Engineer-in-Charge. |
| 90 | Supply and fixing Safety instruction chart of size 3 feet x 2 feet for Electric Shock and Treatment, digitally / UV printed on Aluminium Composite Panel (ACP) sheet of minimum 3 mm thickness, including high-resolution coloured graphics / text in English and Hindi as directed, protective finish / lamination over the ACP sheet alongwith neatly finished edges and complete with provisioning of suitable stainless-steel / brass fixing screws, spacers and all accessories complete all as specified and as directed by Engineer-in-Charge. |
| 91 | Supply, installing, testing and commissioning of LED illuminated sign board of size 150cm x 80cm, comprising of minimum 3 mm thick Acrylic sheet fixed seamlessly with suitable size Aluminium Composite Panel (ACP) material complete including MS backing and frame by making the complete box of depth not less than 75mm alongwith LED illumination system with required / suitable SMPS & providing internal electrical wiring, connectors, cable glands, mounting arrangement, fasteners, weatherproof sealing and all necessary accessories as required; complete with fabrication and erection of independent supporting structure comprising of two Nos. 50mm bore dia GI pipe working as posts of approximately 3.0 m height alongwith MS angle-iron framework / brackets at top and intermediate supports / stiffeners as required for securely mounting the sign board including cutting, welding, drilling, grinding, fabrication, alignment, erection and fixing of the complete supporting structure including bolts, nuts, washers and foundation, coping etc.arrangement for the supporting posts and painting with one coat of red oxide / zinc chrome primer and two coats of approved synthetic enamel paint to all exposed MS / GI surfaces, fixing of the illuminated acrylic sign board to the supporting framework with suitable SS fasteners, complete electrical connection, testing of LED illumination and commissioning complete all as specified and as directed by Engineer-in-Charge. |
| 92 | Supply only Aluminium sulphate Non-ferric alum bricks conforming as per IS 260:2024, suitable for treatment of water intended for drinking, in approved form and grade including necessary packing, handling and delivery complete all as specified and directed by Engineer-in-Charge. |
| 93 | Supply only Potash alum / Alum crystal conforming as per IS 258:2000, suitable for treatment of water intended for drinking, in approved form and grade including necessary packing, handling and delivery complete all as specified and directed by Engineer-in-Charge |
| 94 | Supply only Polyaluminium chloride powder form conforming as per IS 15573:2018, suitable for treatment of water intended for drinking, in approved form and grade including necessary packing, handling and delivery complete all as specified and directed by Engineer-in-Charge. |
| 95 | Supply only Inorganic polymerised liquid primary coagulant of brand name- \\"UNI-ALARTAN\\" of Declibac technologies private limited suitable for treatment of water intended for drinking in approved form and grade including necessary packing, handling and delivery complete all as specified and directed by Engineer-in-Charge |
| 96 | Supply only Soda Ash light (Sodium Carbonate, Na₂CO₃) for Drinking Water Treatment Grade with minimum 99% purity, white free-flowing powder, conforming to IS 251:1998, suitable for pH and alkalinity correction in potable water treatment plants including necessary packing, handling and delivery complete all as specified and directed by Engineer-in-Charge(Make- TATA Chemicals / GHC Ltd) |
| 97 | Supply only chemical for drinking water treatment, calcium based granular high strength disinfectant chlorinating chemical having 65% to 70% chlorine content in granular form in a 45kg drum, and Brand name should be from any manufacturer aproved by E-in-c's branch. Supply and fixing Bib taps fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, suitable for GI pipe of size 15 mm complete all as specified and directed Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 27, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 20 daysDec 05, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 28 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender