Tender For Special Repair/Replacement Of Old Vintage Corroded/Rusted Ci/Gi Pipe Line To Di Pipe Line In The Area Of Mall Road, Young Road Of Zone A Under Age E/M-I Of Ge Dehradun
Tender Value
43.70 Lakhs
Estimated cost
Bid Submission
28 Nov 2026
21 days left
EMD
87400
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dehradun → Uttarakhand
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair/Replacement Of Old Vintage Corroded/Rusted Ci/Gi Pipe Line To Di Pipe Line In The Area Of Mall Road, Young Road Of Zone A Under Age E/M-I Of Ge Dehradun
BOQ
| Sl. No. | Item Description |
| 1 | DESCRIPTION OF ITEMS |
| 2 | M&L for excavation in trenches in hard dense soil not exceeding 1.5 Meter wide and not exceeding 1.5 Meter deep in any type of soil including cutting in slopes etc for laying of pipe line including getting out, complete all as specified and directed. |
| 3 | M&L for returning, filling in, including spreading, leveling, watering and well ramming in layers in soft / loose soil not exceeding 25 cm in each layer complete all as specified and directed by Engineer-in-Charge. |
| 4 | M&L for removal of excavated material (Soil) to a distance up to 50 Meter from starting point and depositing where directed at level not exceeding 1.5 Meter above as directed by Engineer-in-Charge. |
| 5 | Dismantling and taking out the existing corroded /scaled CI/DI/GI pipe of size 150mm with fittings connections from trenches, removal from site or disposed off complete with all fittings including gate valves, all as specifed and directed by Eng-in-charge. Note: Excavation and earth work shall be measured and paid seperately under respective item. |
| 6 | Dismantling and taking out the existing corroded /scaled CI/DI/GI pipe of size 200mm with fittings connections from trenches, removal from site or disposed off complete with all fittings including gate valves, all as specifed and directed by Eng-in-charge. Note: Excavation and earth work shall be measured and paid seperately under respective item. |
| 7 | Supply, laying and testing of spigot and socket ductile iron water tubing,class K-9,of size 150mm, cement mortar lining on inner surface and one coat of bituminous paint over exposed surface ISI marked, IS No. 8329: 2000, including rubber joint of suitable size laid in trenches with proper alignment as per site requirement and carryout testing against leakage before filling the trenches etc complete all as specified and directed. |
| 8 | Supply, laying and testing of spigot and socket ductile iron water tubing,class K-9,of size 200mm, cement mortar lining on inner surface and one coat of bituminous paint over exposed surface ISI marked, IS No. 8329: 2000, including rubber joint of suitable size laid in trenches with proper alignment as per site requirement and carryout testing against leakage before filling the trenches etc complete all as specified and directed. |
| 9 | M & L for CI/DI fitting for spigot & socket end pipes such as Bends (any type, radius and angle), upto 300 mm bore including removing/ dismantling of old CI/GI/DI fittings complete all as specified and directed. |
| 10 | Cutting the existing hard standing/ metal road of facilitate for laying of water pipe line of any type any size and making good the disturbed portion to bring it to original condition with plain cement concrete 1:2:4 type B1 using (20 mm graded stone aggregate) all as specified and as directed. Note: PCC shall be measured and Paid seperately under respective item of schedule. |
| 11 | M&L for cement concrete 1:2:4 type B1 using (20 mm graded stone aggregate) as in mass concrete including necessary form work finished even and smooth and making good the disturbed portion to bring it to original condition complete all as specified and directed. |
| 12 | Dismantling /taking out defective CI/DI Sulice Valve and Supplying, fixing and jointing CI sluice valve, ISI marked, Class PN-1.6 (Non Rising type) with flanged and drilled ends, suitable for 200mm nominal bore pipe/fittings with iron wheel high tensile steel spindle (and gear metal locking part) with & including joints and jointing materials such as bolt, nuts, washers and rubber gasket etc complete all as specified & as directed. |
| 13 | Dismantling /taking out defective CI/DI Sulice Valve and Supplying, fixing and jointing CI sluice valve, ISI marked, Class PN-1.6 (Non Rising type) with flanged and drilled ends, suitable for 150mm nominal bore pipe/fittings with iron wheel high tensile steel spindle (and gear metal locking part) with & including joints and jointing materials such as bolt, nuts, washers and rubber gasket etc complete all as specified & as directed. |
| 14 | Dismantling /taking out defective CI/DI Sulice Valve and Supplying, fixing and jointing CI sluice valve, ISI marked, Class PN-1.6 (Non Rising type) with flanged and drilled ends, suitable for 100 mm nominal bore pipe/fittings with iron wheel high tensile steel spindle (and gear metal locking part) with & including joints and jointing materials such as bolt, nuts, washers and rubber gasket etc complete all as specified & as directed. |
| 15 | Dismantling /taking out defective CI/DI Air Release Valve and Supply & Fix CI/DI Air Release Valves with two air outlets, 80 mm dia bore and fixing up in DI Pipe supply mains suitable upto 200 mm Dia Bore |
| 16 | Suplly and fix in replacement cast iron ''mechanical joint set complete of two flanged collar one no sleeve two nos rubber \\"O\\" ring and nut bolts washers of suitable size for 150 mm bore CI/DI pipe complete including necessary cuting, grinding work to fix in pipe as directed. |
| 17 | Suplly and fix in replacement cast iron ''mechanical joint set complete of two flanged collar one no sleeve two nos rubber \\"O\\" ring and nut bolts washers of suitable size for 200 mm bore CI/DI pipe complete including necessary cuting, grinding work to fix in pipe as directed. |
| 18 | S&F cast iron 'D' joint set complete of two flanged collar one no sleeve two nos rubber 'O' ring and nut bolts washers of suitable size for 150 mm bore CI/DI pipe complete including necessary cutting, grinding work to fix in pipe as directed. (Note:- Earth work required to clear the existing pipe line shall be measured and paid separately) |
| 19 | S&F cast iron 'D' joint set complete of two flanged collar one no sleeve two nos rubber 'O' ring and nut bolts washers of suitable size for 200 mm bore CI/DI pipe complete including necessary cutting, grinding work to fix in pipe as directed. (Note:- Earth work required to clear the existing pipe line shall be measured and paid separately) |
| 20 | M&L for construction of brick masonry valve pit of size 120 cmx120cmx120cm with necessary excavation , returning filling in, steel work for cover using MS Chequred Plate 3 mm thick welded/hinged MS angle iron 50×50×6 cm forged flat iron hinges, sliding type lifting handle of MS bar 12 mm dia locking arrangement at one end, including painting of all metallic parts with two coat of synthetic enamel paint over a coat of red oxide, complete all as specfied and directed. |
| 21 | Supplying and fixing 200mm dia MS pipe ERW,6mm in thickness in six metre length having threading and welding at both ends externally confirming to IS 3589 including two coats of anti corrosive paint (approved colour) over a coat of primers on external surfaces of pipes complete all as specified and as directed. Note: Laying of MS pipe can be vertical or horizontal in direction. |
| 22 | Supplying and fixing 150mm dia MS pipe ERW,6mm in thickness in six metre length having threading and welding at both ends externally confirming to IS 3589 including two coats of anti corrosive paint (approved colour) over a coat of primers on external surfaces of pipes complete all as specified and as directed. Note: Laying of MS pipe can be vertical or horizontal in direction. |
| 23 | M&L for cutting of Ductile iron pipe or any other type of upto 200 mm bore for insertion of tees, collars, sluice valves, etc including dewatering work required for working water pipe lines complete all as specified and directed. |
| 24 | M&L cutting existing steel tubing for alterations or additons (each cut measured) for the following sizes complete all as specified and directed |
| 25 | (a) 20 mm |
| 26 | (b) 25 mm |
| 27 | (c) 40 & 50 mm |
| 28 | Material and labour for any type of steel sections , nut- bolt, washers, sheets, back plate, xpm mesh, wire mesh, bending, cutting in shape, welding, drilling holes, flanges for supporting of DI pipe wherever required/ as per site requirement including painting with two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed. |
| 29 | Dismantling and taking out the existing corroded / scaled GI pipe / PPR/ PALP pipe with fittings connections from trenches, walls, ceiling or floor and removal from site or disposed off for the following sizes complete with all fittings including gate valves, all as specifed and directed. Note: Excavation and earth work shall be measured and paid seperately under respective item of schedule \\"A\\" |
| 30 | 25 mm bore |
| 31 | 40 mm bore |
| 32 | 50 mm bore |
| 33 | 80 mm bore |
| 34 | 100 mm bore |
| 35 | Supply, Laying, fixing & testing galvanished iron water tubing 'medium grade; with and inclduing all GI fittings such as flanges, unions reducers sockets, socket reducing bends , elbows, tee, checkneuts, caps, plugs etc laid in trenches for the following sizes complete all as specifed and directed. Note: Excavation and earth work shall be measuered and paid seperately under respective item of schedule 'A\\". |
| 36 | 25 mm bore |
| 37 | 40 mm bore |
| 38 | 50 mm bore |
| 39 | 80 mm bore |
| 40 | 100 mm bore |
| 41 | Dismantling/taking out defective Gun metal gate valve S&F for Gun metal gate valve with iron wheel head by screwing/cutting of existing pipe lines for the following size complete all as specifed and directed. |
| 42 | 25 mm bore |
| 43 | 40 mm bore |
| 44 | 50 mm bore |
| 45 | 80 mm bore |
| 46 | Refixing of Old GI tubing in New or Old Position complete all as specifed and directed. |
| 47 | 20 mm bore |
| 48 | 25 mm bore |
| 49 | 40 mm bore |
| 50 | 50 mm bore |
| 51 | 80 mm bore |
| 52 | M&L for disconnection of existing pipe line of any type of 25 mm dia to 80 mm dia and disconnect the same from main CI/DI Pipe line and provide end plug to existing water pipe line (CI/DI/GI/MS) |
| 53 | Supply and fixing MS flange of suitable thickness for 200 mm dia pipe min 8 mm thick including drilling, welding, nuts, bolts, rubber gasket insertion and painting complete all as specified and directed. |
| 54 | Supply and fixing Non-Return Valve of 200 mm dia including jointing material complete all as specified and directed by Eng-in-charge. |
| 55 | Note : Tenderers may note that amount of credit Rs 318865.00 will be deducted from the total amount arrived, at the time of Acceptance of contract. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 21 daysNov 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 23 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender