Tender For Civil And Furnishing Works For Establishment Of Circle Office Network Operation Centre (Noc) At 2Nd Floor, Atx Building, Arera Hills, Bhopal M.P.
Tender Value
56.66 Lakhs
Estimated cost
Bid Submission
16 Nov 2026
9 days left
EMD
1.14 Lakhs
Bank guarantee accepted
Document Fee
1180
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bhopal → Madhya Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Civil And Furnishing Works For Establishment Of Circle Office Network Operation Centre (Noc) At 2Nd Floor, Atx Building, Arera Hills, Bhopal M.P.
BOQ
| Sl. No. | Item Description |
| 1 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc., up to floor five level, excluding the cost of centering, shuttering and finishing : |
| 2 | 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 3 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing : |
| 4 | 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources: 10 graded stone aggregate 40 mm nominal size derived from natural sources). |
| 5 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : |
| 6 | Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 7 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 3.5 in superstructure above plinth level up to floor V level. |
| 8 | Cement mortar 1:4 (1 cement :4 coarse sand) |
| 9 | Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.ird course of half brick masonry. |
| 10 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. |
| 11 | Granite stone slab colour black, Cherry/Ruby red |
| 12 | Area of slab upto 0.50 sqm |
| 13 | Area of slab over 0.50 sqm |
| 14 | Extra for providing opening of required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete |
| 15 | Providing and fixing plywood 4 mm thick (MR grade) conforming to IS: 303 for plain lining / cladding with necessary screws, nails etc. all complete as per direction of Engineer in Charge. |
| 16 | Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete. |
| 17 | Size 40 mm |
| 18 | Providing and fixing chromium plated brass 50 mm cupboard or wardrobe knobs with nuts complete. |
| 19 | Providing and fixing chromium plated brass handles with necessary screws etc. complete: |
| 20 | 75 mm |
| 21 | Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. |
| 22 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : |
| 23 | 300x16 mm |
| 24 | 250x16 mm |
| 25 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : |
| 26 | 300x10 mm |
| 27 | 200x10 mm |
| 28 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 29 | 125 mm |
| 30 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 31 | Twin rubber stopper |
| 32 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. |
| 33 | 1.0 mm thick. |
| 34 | Providing and fixing decorative high-pressure laminated (HPL) sheets of 1 mm thickness, soft and easily mouldable type, of approved make, colour and texture, suitable for curved and shaped surfaces, fixed over prepared substrate using approved adhesive and fixing accessories. The work shall include cutting, heating/moulding to required shape, pasting, pressing, edge finishing, trimming and cleaning to achieve a smooth and uniform finish, complete in all respects, as per design and direction of the Engineer-in-Charge. |
| 35 | 1.0 mm thick. |
| 36 | Providing and fixing 19 mm thick BWP grade marine ply as per IS 710 of approved brand for shelves, racks, almirah, cupboard, drawer etc. including necessary nails, screws etc. complete as per direction of Engineer-in-charge. |
| 37 | Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 mm long with screws etc. complete as per directions of Engineer- in-charge. |
| 38 | Providing and fixing 2 mm thick 16 to 19 mm wide PVC edge binding tape of approved quality for cuboard/wardrobe shutters including necessary synthetic resin hot pressed to edges on binding machine etc. complete as per direction of Engineer-in-charge. |
| 39 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. |
| 40 | Fixed to steel windows by welding |
| 41 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. |
| 42 | Double charge vitrified tile polished finish of size |
| 43 | Size of Tile 600 x 600 mm |
| 44 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08%and conforming to IS: 15622, of approved brand & manufacturer in all colours and shade in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints(Payment for grouting of joints to be made separately). |
| 45 | Size of Tile 600x600 mm |
| 46 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS :5382, leaving 10 mm gap for thermal expansion. |
| 47 | Single tee with door |
| 48 | 110x110x110 mm |
| 49 | Single tee without door |
| 50 | 110x110x110 mm |
| 51 | Bend 87.5° |
| 52 | 110 mm bend |
| 53 | Shoe (Plain) |
| 54 | 110 mm Shoe |
| 55 | Coupler |
| 56 | 110 mm |
| 57 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. |
| 58 | 110 mm |
| 59 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \\"T\\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. |
| 60 | Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. |
| 61 | 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16 mm thick fire retardant PVC film on the face side and 12 micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. |
| 62 | 12 mm cement plaster of mix : |
| 63 | 1:6 (1 cement: 6 fine sand) |
| 64 | 15 mm cement plaster on the rough side of single or half brick wall of mix : |
| 65 | 1:6 (1 cement: 6 fine sand) |
| 66 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 67 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre. of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. |
| 68 | One coat. |
| 69 | Two coats. |
| 70 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. |
| 71 | With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre. |
| 72 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer, of required shade and colour all complete : |
| 73 | New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre |
| 74 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound ) content less than 50 gram/ litre, of approved brand and of required shade and colour complete to give and even shade. |
| 75 | Old work (one or more coats) |
| 76 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-harge. |
| 77 | With cement mortar 1:4 (1cement: 4 coarse sand). |
| 78 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. |
| 79 | Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) |
| 80 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 81 | Flexible pipe |
| 82 | 32 mm dia |
| 83 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc. |
| 84 | 20 mm nominal outer dia .Pipes. |
| 85 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work |
| 86 | 25 mm nominal outer dia. Pipes. |
| 87 | Providing and fixing uplasticised PVC connection pipe with brass unions : |
| 88 | 45 cm length |
| 89 | 15 mm nominal bore |
| 90 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : |
| 91 | 25 to 40 mm nominal bore |
| 92 | Providing and fixing SS grating of approved quality and colour. |
| 93 | Rectangular type with openable circular lid |
| 94 | 150 mm nominal size square 100 mm diameter of the inner hinged round grating |
| 95 | Providing & fixing PVC moulded P-trap long arm of self cleansing design in floor including the cost of cutting the floor, removal of old trap, (if any) and making good the walls / floor, of approved quality all complete as per the direction of Engineer-In-Charge: - 110mm inlet and 110mm outlet. |
| 96 | Repairing of existing door / window shutter by chiseling, fixing of fittings like hinges, tower bolts, etc. if required for smooth operation of shutter all complete as per the direction of Engineer-In-Charge. |
| 97 | Providing and fixing brass bib cock of approved quality : |
| 98 | 20 mm nominal bore |
| 99 | Providing and fixing brass stop cock of approved quality : |
| 100 | 20 mm nominal bore |
| 101 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc. to be paid separately). |
| 102 | Providing and fixing frameless toughened glass of approved brand and manufacture, fixed in position including providing and fixing approved SS fittings, clamps, channels, or patch fittings as required, including necessary drilling, edge polishing, making cut-outs/holes, and all fixing accessories, complete. The work shall include proper alignment, leveling, and finishing to achieve a neat and uniform appearance, complete in all respects, as per the direction of the Engineer-in-Charge. |
| 103 | 12 mm thick |
| 104 | Providing and fixing CP Brass health faucet with 1m long PVC hose of approved brand and manufacture and of approved shade - 15mm |
| 105 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : |
| 106 | For fixed portion |
| 107 | Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 108 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately). |
| 109 | Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 110 | Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. |
| 111 | Pre-laminated particle board with decorative lamination on both sides. |
| 112 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): |
| 113 | With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 114 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg., for doors, including cost of cutting floors ,embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. |
| 115 | With stainless steel cover plate minimum 1.25 mm thickness. |
| 116 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 117 | Providing and applying damp-proofing treatment on internal plastered brick or concrete wall surfaces affected by rising dampness, efflorescence, or salt formation using ready-to-use waterproofing chemical of approved make such as Asian Paints Hydroloc, Dr. Fixit Dampguard Classic, or Berger Dampstop, in two coats with brush or roller, including surface preparation by wire brushing, scraping off loose material, removal of existing flaking paint or salt deposits, pre-wetting of the surface, and curing, all complete as per manufacturer’s specifications and as directed by the Engineer-in-Charge. Note: All materials and application shall strictly adhere to the product datasheet of the selected brand and coverage shall not be less than 50–60 sq.ft. per litre per coat depending on surface porosity. |
| 118 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 119 | Providing and fixing aluminium die cast body tubular type universal HEAVY DUTY hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 150 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. (Godrej, Dorma, Ozone as approved) |
| 120 | Providing and fixing 8 mm thick heavy-duty tufted carpet tiles or carpet sheet of approved make, shade and pattern in office premises, laid over RCC floor, screed or raised access flooring, including cleaning and preparation of the base surface, application of approved pressure-sensitive adhesive, proper laying, alignment, pattern matching, cutting and trimming complete, as per manufacturer’s specifications. The carpet shall be made of solution-dyed nylon or polypropylene fibre with PVC/bitumen backing, fire-retardant, anti-static, stain-resistant and suitable for heavy commercial office use.The rate shall include the cost of carpet material, adhesive, labour, tools, handling, wastage, cutting around columns, walls, electrical boxes and other obstructions, rolling and pressing for proper bonding, neat finishing at edges, doors and skirting, cleaning of the site after installation and all incidental charges, complete in all respects. Measurement shall be made in square metres on the net area actually carpeted, as per direction of Engineer-in-Charge. |
| 121 | Providing and fixing decorative PET acoustic panels of approved make, colour, thickness and texture, fixed over approved quality HDMR board backing on walls, partitions, wall linings or columns, including cutting, alignment, fixing and finishing complete, over existing wall surface or MS hollow tube framework, as per approved drawings and directions of Engineer-in-Charge. The PET panel shall be minimum 9 mm thick, made from recycled polyester fibre, having sound-absorbing properties (NRC not less than 0.60), fire-retardant and suitable for office interiors. The HDMR board shall be minimum 12 mm thick, exterior grade and of approved make, providing a rigid and level base for fixing the PET panels. |
| 122 | The item shall include supply and fixing of approved HDMR board, PET acoustic panels, stainless steel screws, wall plugs, anchors, approved adhesive, joint alignment, edge trimming, cutting around electrical boxes and openings, scaffolding if required, cleaning of surface after installation and all labour, tools, wastage, handling and transportation, complete in all respects. The supporting MS hollow tube framework, wherever required, shall be paid separately. Measurement shall be made in square metre on net finished surface area, as per direction of Engineer-in-Charge. |
| 123 | Providing and fixing wall panelling using 12 mm thick HDMR (High Density Moisture Resistant) boards of approved make, fixed over pre-installed MS framework, complete as per design and direction of Engineer-in-Charge. The HDMR boards shall be cut to required sizes and fixed to the MS frame using self-tapping screws at suitable spacing, ensuring proper alignment, line and level. All board joints shall be properly staggered, filled with putty, and sanded smooth to provide an even surface ready to receive further finishes such as laminate, paint, veneer or wall covering, as specified. The item shall include the cost of HDMR boards, screws, jointing compound, labour, tools, scaffolding, cutting, wastage, surface preparation and making good the finished surface, complete in all respects, but excluding the cost of MS framework, which shall be measured and paid for separately. The work shall be measured in square metre of finished wall panelling surface. |
| 124 | Providing and fixing frame work for partitions/ wall lining etc. made of 50x50x1.6 mm hollow MS tube, placed along the walls, ceiling and floor in a grid pattern with spacing @ 60 cm centre to centre both ways (vertically & horizontally) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of approved steel primer etc. complete, all as per direction of Engineer-in-charge. |
| 125 | Providing and fixing interior decorative fluted wall panels (Louvers) made of high-quality rigid PVC/ Charcol of approved make, shade and profile, fixed over prepared surface or on pre-installed framework, complete as per design, pattern and direction of Engineer-in-Charge. The fluted PVC panels shall be of uniform thickness, UV-stabilized, moisture-proof, termite-proof and fire-retardant grade, with continuous vertical or horizontal grooves as specified. Panels shall be cut to required sizes and fixed using approved adhesive and/or concealed mechanical fasteners, ensuring proper line, level and neat joint alignment. All joints, edges and terminations shall be finished neatly with matching PVC trims or beading for a uniform and aesthetically pleasing appearance.The item shall include the cost of PVC fluted panels, adhesives, fasteners, trims, labour, tools, scaffolding, cutting, wastage, surface preparation and making good the surrounding surfaces, complete in all respects as per drawings and instructions of Engineer-in-Charge. The work shall be measured in square metre of finished fluted wall panel surface. |
| 126 | supplying and fixing factory-manufactured modular office workstation table of approved make, design and colour, suitable for modern office / IT workstation use, complete in all respects as per approved drawings and directions of Engineer-in-Charge.Each workstation module shall consist of two-seater or three-seater configuration, each seat having a minimum size of 1200 mm length and 750 mm width, comprising of the following:1. Worktop and structural panels:The workstation shall be made from factory-manufactured modular panels. The worktop shall be of 25 mm thick pre-laminated BWP / HDHMR board, finished with 1 mm thick decorative laminate on the top and balancing laminate on the bottom, with all exposed edges sealed with 2 mm thick PVC edge banding. The worktop shall be supported on 18 mm thick laminated HDHMR side panels providing full height privacy and structural rigidity. |
| 127 | A front modesty panel of 18 mm thick laminated HDHMR board shall be fixed between the side panels to conceal the leg space and CPU area. A rear privacy / screen panel of minimum 18 mm thick laminated HDHMR board, in angular profile as shown in drawings, shall be provided for visual and acoustic separation between adjacent workstations.2. Cable management, power access and accessories:The workstation shall be provided with an integrated cable management system, consisting of a top-mounted raceway with flip-open or removable power and data access box, complete with brush strips, modular cut-outs, cover plates and internal cable tray for routing of power, data and AV cables. A CPU holder or CPU trolley made of powder-coated MS shall be fixed below the worktop for each seat.3. Supports, fittings and installation:The workstation shall be supported on powder-coated MS brackets and structural fittings for strength and stability. The item shall include all laminated HDHMR boards, laminates, PVC edge banding, SS screws, |
| 128 | concealed fittings, dowels, adhesives, MS brackets, cable trays, raceway boxes, cutting, drilling, finishing, alignment, leveling, transportation, handling, wastage, labour, tools and complete installation at site, as per drawings and as directed by the Engineer-in-Charge.Measurement:The workstation shall be measured per seat, each seat having a minimum working size of 1200 mm × 750 mm, irrespective of whether arranged in two-seater or three-seater modules. |
| 129 | Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, including embeding prelaminated particle board as specify whereever required all complete as per the direction of the Engineer-in-charge. |
| 130 | Providing and fixing unplasticised rigid pvc SWR waste and vent pipes conforming to IS : 13592 Type B, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. |
| 131 | 110mm diameter. |
| 132 | Providing and fixing unplasticised rigid pvc SWR fittings conforming to IS : 13592 Type B, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 133 | 110mm Y - Tee |
| 134 | Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. |
| 135 | Providing and fixing Zebra style vanishing blinds curtains of Marvel/Vista made of dual-layered polyester fabric, consisting of alternating transparent and opaque horizontal stripes, allowing light control and privacy. The blind shall be mounted on powdercoated aluminum roller tube of required diameter, with side chain mechanism for smooth operation. The system shall include brackets, end caps, bottom rail, all necessary fittings and fixtures, and installation complete in all respects. Shade and mechanism to be approved by Engineer-in-charge. |
| 136 | Providing and fixing Quartz Single Bowl Kitchen Sink of size 610 × 460 × 230 mm (610x510 mm bowl depth 200 mm), made of Quartz composite material (approx. 80% natural quartz stone and 20% acrylic resin), with matt/satin finish, scratch, stain, and heat-resistant surface, including CI/SS brackets, stainless steel waste coupling (40 mm), CP bottle trap, making cut-outs in granite top, sealing joints, and making good the walls wherever required, complete in all respects as per direction of the Engineer-in-Charge. (Make: Carysil / Kaff / Franke / Nirali / Futura or equivalent) |
| 137 | Providing and fixing 3D wallpaper on finished wall surfaces, of approved make such as Asian Paints (Nilaya), Marshalls, or equivalent, in approved shade, pattern and texture, using adhesive of approved quality as recommended by the manufacturer. The surface shall be properly cleaned, leveled, and prepared to receive the 3D wallpaper. The work shall include cutting, pasting, proper alignment, matching of patterns/relief, and finishing at edges, corners, and openings, complete in all respects. Measurement shall be taken on finished surface area only, as per design and direction of Engineer-in-Charge. |
| 138 | Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : |
| 139 | 2nd class teak wood |
| 140 | 50x12 mm |
| 141 | 50 x 20 mm |
| 142 | Providing & fixing chrome plated brass battery based infrared sensor operated pillar cock of approved quality and make, having foam flow technology. |
| 143 | 15 mm nominal bore. |
| 144 | Providing and fixing sun control film of approved make and shade on office window panes, including cleaning of glass surface, cutting film to required size, fixing with required solution, and cleaning after completion, complete as per direction of Engineer-in-Charge. |
| 145 | Repairing of existing office chairs including replacement/repair of damaged seat and back cushioning with new foam of 40 kg/m^3 density and re-upholstery in fabric/leatherette, tightening and fixing of loose joints, repair/replacement of armrests, servicing or replacement of gas lift mechanism, tilt mechanism, and base, including providing and fixing of new castor wheels (“sockets/castors”), nuts, bolts and all necessary fittings, complete in all respects as per the directions of Engineer-in-Charge. |
| 146 | Providing and fixing cutlery drawer basket made of stainless steel (SS 304 grade) with solid bottom plate type construction (not wire mesh) of Make-Ebco / Hettich / Hafele or equivalent approved, fitted with soft-close telescopic slides, including PVC or rubber mat lining, screws, clips, and fixing hardware complete as per design.The basket shall have overall internal dimensions approximately Width 600 mm × Depth 450 mm × Height 100 mm, with smooth polished stainless-steel finish, rounded corners, and anti-corrosive coating.The rate includes cost of all materials, labour, cutting, edge finishing, fixing, alignment, and complete installation in position, (Each basket complete in position)all as directed by the Engineer-in-Charge. |
| 147 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.. |
| 148 | In cement mortar |
| 149 | Dismantling aluminium partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge. |
| 150 | Refixing of available aluminium partitions, doors, windows, glazing, etc., including providing and fixing cleats, screws and neoprene gaskets, and cutting aluminium members, glass, boards, etc., to the required dimensions, complete in all respects as directed by the Engineer-in-Charge. |
| 151 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. |
| 152 | Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble |
| 153 | Area of slab over 0.50 sqm |
| 154 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \\"T\\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. |
| 155 | Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. |
| 156 | GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness60 microns (minimum), including factory painted after bending and perforation and backed with a black Glass fiber acoustical fleece. |
| 157 | Providing and fixing liquid soap dispensor of Parryware (Model no. T6913A1) or equivalent make as approved by Engineer in Charge. |
| 158 | Providing and fixing SS decorative sliding door bolts with nuts and screws etc. complete |
| 159 | 300x16 mm |
| 160 | 250x16 mm |
| 161 | Providing and fixing SS decorative tower bolt (Barrel type) with necessary screws etc. complete. |
| 162 | 250x10 mm |
| 163 | Providing and fixing SS decorative door latches with screws etc. complete. |
| 164 | 300x20x6 mm |
| 165 | Providing and fixing SS decorative handles with necessary screws etc. complete. |
| 166 | 125 mm |
| 167 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: |
| 168 | 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 169 | Proiving and fixing Bib cock (15mm nominal bore) of \\"Jaquar\\" or equivalent make all complete as per direction of Engineer in charge. |
| 170 | Proiving and fixing Stop cock/ angle cock (15mm nominal bore) of \\"Jaquar\\" or equivalent make all complete as per direction of Engineer in charge. |
| 171 | Proiving and fixing Long body bib cock (15mm nominal bore) of \\"Jaquar\\" or equivalent make all complete as per direction of Engineer in charge. |
| 172 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. |
| 173 | Fixed to steel windows by welding |
| 174 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 175 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 176 | Extra for making design charges for CNC cutting of MS aheet jali of the required thickness as per approved desIgn and instructions of the Engineer in Charge. (The plain MS sheet shall be measured and paid for separately under the relevant Item) |
| 177 | Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. |
| 178 | After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod pf approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. |
| 179 | Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS:16231 shall be paid separately. |
| 180 | Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for: |
| 181 | (i) Sites with basic wind speed > 45 m/sec as per IS 875 - Part 3 |
| 182 | (ii) Sites with structure height more than 20m for all wind speeds. |
| 183 | Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. |
| 184 | Using R2 series with frame (70mm & above) x (40mm & above) & both glazed and fly screen sash (25mm & above) x (50mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 meter). |
| 185 | Supplying, Installing & Providing factory made Conference Table of overall size W4800 x D1200 x H750 mm, the worktop shall be of overall 50 mm thickness, made of pre-laminated particle board, duly edge-banded with 2 mm thick PVC lipping on all edges. The tabletop shall be designed in dual shades with a white matching laminate board provided below the top surface to enhance aesthetics. The center portion of the table shall include a matching laminate shade panel for an elegant appearance with wire management provision (gromnet box). Under structure includes 18 mm thick prelaminated gable ends in 100–150 mm wide box structure, and 18 mm modesty panels with 2 mm PVC edge lipping in approved shade. Also provided: 1 storage unit (W800 x D350 x H700 mm) below round top, made of 18 mm pre-laminated board, with 1 shelf & 2 shutters. There shall be buffers provided to avoid scratches on the floor. Product shall be in knockdown construction, using ISI-marked prime quality boards. Design, make, materials & colours as per Engineer-in-Charge’s direction including transportation. |
| 186 | \\"Supplying, providing, and installing factory made Dining Tablewith Chair Set (8 Nos) for 8 Seater configurations (of approved make & design as per direction of E/C). The overall size of the 8-seater table is L1800 x W915 x H760 ±10mm. Each chair is sized L435 x W430 x H875 ±10mm. The tabletop and supporting structure are crafted from high-quality, seasoned solid wood (Sheesam/teak), ensuring outstanding sturdiness, superior longevity, and resistance to everyday wear and tear. The chair is made from high-quality seasoned Solid (Sheesham/Teak) wood, oAering robust construction, durability, and resistance to daily wear and tear. The chair features a high backrest designed with vertically aligned wooden slats and dual horizontal slats at the top, ensuring both ergonomic support and contemporary aesthetics. The seat is provided with a wellcushioned, upholstered pad in a premium fabric or leatherette for enhanced user comfort. Structural stability is reinforced with cross-stretchers connecting the legs. The set is aesthetically designed with a modern finish, oAering comfort and elegance suitable for dining spaces. premium finish for both the table and chairs: Honey, providing flexibility to suit varied interiors. All items supplied shall be installed and positioned as per site requirements including transportation and as per direction of the Engineer-in-Charge, complete in all respects as specified |
| 187 | Providing and supplying factory made High Back Adjustable Lumber Fixed Armrest Nylon Base (of approved make & design as per direction of E/C). PU Moulded Seat Synchro Tilt Mechanism with Single position Lock chairs with cushioned seat and back, ergonomically designed with single position lock, uphoistered in fabric/leatherette, having sturdy powder- coated steel/metal frame with fixed armrests (if required), suitable for long-duration seating, including supply, transportation, placement at site, and all incidental charges, complete in all respects as per the directions of Engineer-in-charge Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 16, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysNov 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 11 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender