Tender For Provision Of Covered Shed For Common Assembly Area At P-25 Building (Cg School) At Cg Enclave At Cg Enclave Malkapuram Visakhapatnam Under Ge (I)(Cg) Vizag.
Tender Value
43.01 Lakhs
Estimated cost
Bid Submission
28 Nov 2026
21 days left
EMD
86100
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Visakhapatanam → Andhra Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provision Of Covered Shed For Common Assembly Area At P-25 Building (Cg School) At Cg Enclave At Cg Enclave Malkapuram Visakhapatnam Under Ge (I)(Cg) Vizag.
BOQ
| Sl. No. | Item Description |
| 1 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, in cable tench etc. n exc 10 sqm on plan and getting out in soft / loose soil complete all as directed. |
| 2 | Excavating over area n exc 1.5m in depth and getting out in soft / loose soil complete all as directed. |
| 3 | M&L for sand filling under floors or in foundations including watering and consolidation for cushioning complete all as specified and as directed. |
| 4 | M & L for plain cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed. |
| 5 | M & L for designing , providing fabricated , assembling and erection of pre stressed special Arch Membrane roofing structure with MS tubular frame work ( As per is structural steel ) in desired profile as per conceptual drawing with type II Precontraint as per manufacturing and supplying standards by Serge Ferrari /Mehler /Verseidag /Sioen . The membrane should confirm to the manufacturing and supplying standards by being pre stretched in both weft and weft direction manufacturing to perform best dynamic stability in both warp and warp direction with approved installers and manufacture for Arch roofing with and atleast two executed job reference in this connection. The fabric must be of HT polyester yarns 1100D tex coated with uniform 230 micron PVC coating over the polyester yarn . The top quote over the PVC must be of height concentration with easy clean availability and superior white pigmentation of the membrane . The dimensional stability of the fabric should be measure as per elongation test of 24 hrs - 10DAN / 5cm which should confirm < 1 % - < 1 % ( EN15977 ) and residual elongation should confirm < 0.4 % -0.4% ( EN15977 ) ensuring dimensional stability in both weft and warp direction , minimum weight should be 900 to 950gm per sqm (EN ISO 2286-2 ) , 4200/4000 N / 50mm ( EN ISO1421 ) and tear strength of 550 / 500N ( DIN53363 ) and with a guarantee of 10 yrs ( with non depreciating guarantee for first three years ) from the manufacturer , pole to pole spacing of the fabric should be as Arch drg , Plan area of covering used for Covered Shed Chargeable area will be fabric surface area inducing the measurement of the fitting used for fixing the civil drawing of foundation will be provided by the supplier and the foundation if any shall be made by contractor as per drawing produced by manufacturer. The wind pressure report along with foundation drawing shall be provided by the supplier / contractor for future reference as per direction of Engr - in - Charge approved by GE . Minimum design criteria of structure: Round pipe pillar 200mm dia, Rafter round 125mm dia, Connecting Rafter Pole to pole 125mm dia, Covered shed round pipe/ Purlin 75mm dia, Base plate 450x550 mm, SS plate and 25 mm dia. nut bolt , Gl wire rope for fabric , Deco Primer and Paint , 900 GSM Sione white Fabric ,complete all as specified and directed.(Note: Excavation, PCC work, Formwork, RCC work, TMT work and tubular truss will be measured and paid separately in relevant items. |
| 6 | Material and labour for steel work in tubular columns (273.0 x 6.3), bowstring arch trusses (top chord 139.7 x 4.85, bottom chord 114.3 x 4.5, webs 60.3 x 3.6), eaves beams, purlins and X-bracing using ERW/induction butt-welded tubes conforming to IS 1161 (Yst 240), including special-shaped washers, end caps and gusset allowance, fabrication, erection at all heights, complete anchor bolts M24 x 900 mm with nuts, washers and end plates, MS screw bolts, machine made, hexagonal heads, 11-15 mm dia, not exceeding 10 cm long (M12 connection bolts) with nuts and washers base plates (600 x 600 x 25), column cap plates, stiffener ribs, plain angle cleats and similar small articles conforming to Fe 290 (Grade E165). High tensile steel holding down anchor bolts 25mm dia (400-600mm long) with nuts and washers for column base plates (18 columns x 4) complete all as specified and directed. |
| 7 | S&F non shrink cementious grout 30mm thick under column base plate including shuttering and curing complete all as specified and directed. |
| 8 | S & F mild steel bands, straps, supports or stays of rain water, ventilating pipes including bolts, hooks (stay) for large gates, hook and pintel hinges, clamps, hold fasts, wall ties, flat iron fillets for securing wire mesh, wind tie, fan hook and similar work including necessary drilling bolting or riveting etc conforming to Fe – 290 Gde E – 165 complete all as specified and as directed. |
| 9 | S&F Mild steel screw bolts (machine made) 11 to 15mm dia with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm and n exc 10cm long complete all as specified and directed. |
| 10 | M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zine chrome primer complete all as specified and directed. |
| 11 | S&F TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 12 | S&F TMT bars 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 13 | M&L for RCC 1:1.5:3 type A1 (Nominal mix) using 20mm graded stone aggregates as in foundation, footing, mass concrete, foundation beam, plinth beam and base for column complete all as specified and directed. |
| 14 | Use & waste for flat formwork to sides of concrete foundations, footings, bases of columns raft and raft beams, sides and soffits if any of foundations and plinth beams and similar work, etc, rough finished surfaces of concrete etc all as specified and directed. |
| 15 | M&L for 75mm thick Plain cment concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and directed. |
| 16 | M & L for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.18 sqm but n.exc 0.38 sqm, in floors etc, including 20 mm thick screed bed in cement mortor 1:6 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed. |
| 17 | S&F Mild steel sheet eaves gutters, 1.60mm thick, galvanised class 3, half round with rounded edges with and including necessary fixing bolts, gutter bolts, screws, washers, pipe nails, distance pieces, plugs, holder-bats (for pipes without ears), and all jointing materials, and also for all necessary cutting of gutters and pipes, drilling for bolts and jointing and fixing in position bolts and jointing and fixing in position complete all as specified and directed. |
| 18 | S&F 110 mm outer dia UPVC rainwater pipes fixed to walls including necessary brackets / clamps complete all as specified and directed. |
| 19 | M & L for 75 mm thick, plain cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 including necessary formwork complete all as specified and directed. |
| 20 | S&F modular switch 6 Amp, 1 way, 1 module size complete all as specified and directed. |
| 21 | S&F modular switch 16 Amp, 1 way, 1 module size complete all as specified and directed. |
| 22 | S&F Modular socket 6 Amp, 2/3 pin, 2 module size complete all as specified and directed. |
| 23 | S&F modular socket 6A/16 Amp 2/3 pin combined 2 module size complete all as specified and directed. |
| 24 | S&F ceiling rose surface Polycarbonate/ PVC three terminal complete all as specified and directed. |
| 25 | S&F modular metal flush box alongwith modular white cover plate including frame , 3 module complete all as specified and directed. |
| 26 | S&F LED flood lights fitting 1x 30W, 220V, AC with suitable metal clamp for mounting including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. |
| 27 | S&F exhaust fan of, metal body type of Size 450 mm, AC, single phase, 230 volt, with louver and connection with PVC insulated copper conductor cable from fan to ceiling rose complete all as specified and directed. |
| 28 | Supply and fixing of 8 Module IP65 weatherproof enclosure, suitable for housing modular MCBs Each complete with transparent hinged cover, DIN rail, neutral and earth terminals, cable entry provisions/glands, including fixing on wall/structure, making necessary cable connections and testing, complete all as specified and directed . Make & Model: DHDFSBOSRT08 of Havells or equivalent. |
| 29 | S&F MCB 6-32 Amps, SPN, 240 Volt \\"C\\" series, breaking capacity 10 KA complete all as specified and as directed. |
| 30 | S&F MCB 6 to 32 Amps, SP, 240 Volt \\"C\\" series, breaking capacity 10 KA complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 31 | S&F MCB 6 to 32 Amps, SP, 240 Volt \\"C\\" series, breaking capacity 10 KA complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 21 daysNov 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 23 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender