Tender For special Repair Of Water Supply Pipeline And Re-Development Of Borewell And Connected Water Supply Works At Fafa Basantar Line Under Ge (U) W/S Delhi Cantt-10
Tender Value
24.03 Lakhs
Estimated cost
Bid Submission
27 Nov 2026
20 days left
EMD
48060
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
New Delhi → Delhi
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair Of Water Supply Pipeline And Re-Development Of Borewell And Connected Water Supply Works At Fafa Basantar Line Under Ge (U) W/S Delhi Cantt-10
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in trenches not exceeding 1.5 meters wide and not exc. 1.5 meters deep for laying GI pipe line any type of soil, getting out and leveling of bottom surface to required level all as specified and directed by Engr –in-charge. |
| 2 | Returning filling in, including spreading, leveling, watering and well ramming in layers not exc. 25 cm thick all as specified and directed by Eng. In Charge. |
| 3 | Removal of excavated material from site to a distance not exceeding 50 meters away and depositing where directed at a level not exceeding 1.5 meters above the starting point as directed by Engr-in-Charge. |
| 4 | M&L Boring holes under road pavement by bocky manually in any type of soil upto 200 mm bore complete all as specified and directed by Engr-in-Charge. |
| 5 | Drilling not less than 300 mm bore hole by DTH method to any depth below the ground level in any kind of rock/soil upto 120 mtr deep including disposal of surplus soil to a distance not exc 50 mtr away all as specified and directed by Engineer-in-Charge.Note : 1) In case of encountering rock prior to 30 mtr depth from ground level the decision of the Garrison Engineer for reboring shall be final and binding. Specific order in writing shall be issued by Garrison Engineer for reboring and the quantities shall vary accordingly. 2) cost of transportation of DTH plant is included in the unit rate. |
| 6 | Supplying, lowering & fixing into bore 200mm dia MS casing pipe as IS-4270/3589-2001, 6.0 mm thick ERW having duly welded both sides socketed ends all as specified and directed by Engineer-in-Charge |
| 7 | Supplying, lowering & fixing into bore hole 200 mm dia MS casing pipe as per IS 4270-2001, 6.00 mm thick ERW slotted tube having 1000 slots of size 1.58 x 75 mm per mtr length uniformly distributed on surface, duly welded both side socketed ends all as specified and directed by Engineer-in-Charge |
| 8 | Supplying, lowering & fixing into bore 150mm dia MS casing pipe as IS-4270-2001, 6.0 mm thick ERW having duly welded both sides socketed ends all as specified and directed by Engineer-in-Charge |
| 9 | Supplying, lowering & fixing into bore hole 150 mm dia MS casing pipe as per IS 4270-2001, 6.00 mm thick ERW slotted tube having 1000 slots of size 1.58 x 75 mm per mtr length uniformly distributed on surface, duly welded both side socketed ends all as specified and directed by Engineer-in-Charge |
| 10 | Supplying & fixing well cap suitable for 200 mm bore well dia consisting of two parts complete with welding and machinery work having provison of cut out for passing of column pipe and fabricated from MS sheet 3.15 mm thick all as specified & directed by Engr-in-Charge. |
| 11 | Supply & fixing housing clamp for 200 mm dia bore pipe made out of flat MS 100x12 mm thick (length 80 mm) with 4 Nos 20 mm dia of suitable size of bolt, nuts, washers etc including drilling holes of suitable sizes and painting 2 coats of synthetic enamel paints over a coat of red oxide primer all as specified and directed by Engineer-in-Charge |
| 12 | Supply & fixing housing clamp for 50 mm dia bore pipe made out of flat MS 80x10 mm thick (length 60 mm) with 4 Nos 20 mm dia of suitable size of bolt, nuts, washers etc including drilling holes of suitable sizes and painting 2 coats of synthetic enamel paints over a coat of red oxide primer all as specified and directed by Engineer-in-Charge |
| 13 | Development of tube well with air compressor of rating 630 CFM at 100 PSI as required complete all as specified and directed by Engr-in-charge |
| 14 | Supplying and packing pea gravel of size 3.00 mm to 6.00 mm around casing pipe all as specified and directed by Engr-in-Charge. |
| 15 | Material and labour for yield testing of tube well by continuous run with suitable equipment all as per IS-2800 part-II of 1979 including complete testing of water suitable for drinking purpose as per IS-10500 of 1991 from testing Laboratory approved by GE and report shall be submitted to GE. The well shall be tested 24 hours continuous after development of the well to acertain the yield. The air compressure/higher capacity pump required for the development of the well by means of over pumping shall be arranged by the contractor at his own arrangement. |
| 16 | Material and labour for test of pilot bore with electro logging through computerized composite litho log machine at site by ground water consultant and in innovative engineer and submitting complete result pertaining to water strata and recommendation to tap water by providing slotted pipe all as required complete all as specified and directed by Engr-in-charge |
| 17 | Supply, lowering and fixing GI Column pipe heavy duty flanged and drilled ISI marked 50 mm bore as per Class 'C', 3.0 mtr in long flange having 6 mm min. thick, slot cutting in flange for passing of submersible cable incl all jointing material such as bolts, nuts,washers, & packing sheets and connecting complete all as specified and as directed by Engr-in-Charge. |
| 18 | supply and fixing of MS flange 100 mm bore ,16mm thick duly welded with flange joint including nuts bolts ,washer ,Rubber or fiber board gasket joint of size 100 mm size |
| 19 | Material and labour for Rubber Gasket Joint (Tyton Joint) including jointing material for DI/CI pipe of 100 mm bore |
| 20 | Material and labour for Rubber Gasket Joint (Tyton Joint) including jointing material for DI/CI pipe of 150 mm bore |
| 21 | Supply, Installation, lowering, testing and commissioning submersible pumping set having discharge capacity 10 LPS at 160 mtr head complete with submersible motor of suitable model of 7.5 HP, 3 Phase 415 volt complete all as specified and as directed by Engr-in-Charge.Notes :- Old U/s Submersible Pumpset will be deposited to MES strore by The Contractor |
| 22 | Supply, installation, commissioning and testing of LT feeder piller box of size 900x1200x300 mm, outdoor cubical type, floor mounted, vermin proof factory made of CRCA Sheet 3.15 mm thick and MS angle of size 40x40x5mm having suitable legs, both side openable with locking and key arrangement with two Nos pad lock 50 mm make Godrej/Harison, powder coated with three phase, 415 volts, 50 Hz, AC supply all as directed by Engr-in-Charge and comprising of the following:- Incoming (a) 4 pole MCCB 100 A, 4 Pole, 25 KA adjustable-01 No.Outgoing (a) MCCB 40 Amp, 4 Pole, 415 volts, 50 Hz TP, 10 KA - 03 No(b) Aluminium Bus bar fixed on epoxy insulators capacity 200 Amp and bakelite insulation sheet at the back with coloured tape-01 set ( 3 phases and neutral).(c) Ammeter 0-200 Amps flush type size 96 x 96 mm with set of suitable CT’s and selector switch - 1 No.(d) Voltmeter 0-500 Volts Flush type of size 96 x 96mm with selector switch - 1 No.(e) Set of indicator Lamps - 1 No.(f) Star Delta starter fully automatic type ML/MNS-1.5 and set of indicating lamp showing ON/OFF position - 1 No. |
| 23 | (g) Fully automatic phase sequence corrector to correct input reverse phase and also protect against single phasing voltage unbalancing, low high voltage with time delay 4 to 7 second and automatic digital timer switch with automatically on/off the motor starter upto 12.5 HP as per time setting-01 No.(h) Complete internal wiring with suitable size copper conductor and cable lugs & glands complete.(i) Masonry and concrete work for grouting of legs in foundation for mounting of panel -01 Job(j) Cable glands of suitable sizes for cable entry and exit. |
| 24 | Supply, connecting, testing and commissioning cable submersible with copper conductor 3 core 1100 volts grade 4.0 Sqmm nominal cross sectional area stranded conforming to relevant IS complete as specified and as directed by Engineer-in-Charge. |
| 25 | Supply, laying jointing, testing DI pipe with class-K-7 spigot socketed ends , conforming to IS-8329 laid in trenches including providing route indicators of suitable height and laying at spacing of @ 50m center to center at GL mentioning name of contractor, date of execution & CA No with name of work & rubber gasket (Tyton) joints with jointing material & route indicators of the following sizes including taking down of existing CI/DI pipe complete all as specified and directed by Engineer-in-Charge. (Note : (i) Excavation & earth work shall be measured & paid separetely under respective items of BOQ.(ii) Contractors will provide route indicators mild steel body with top 150 mm plate 3mm thick and height not less than 300mm above finished GL at suitable intervals as directed by EIC. Cost of route indicators shall be deemed included in quoted unit rates.(iii) DI pipe whole quantity of tender shall be procured by contractor in one time from the authorised dealer of approved make and PV's, MTC & e-way bill will produced by contractor during payment of 1s RAR as material laying at site.(iv) Piece meal site for laying of pipe shall be given by EIC and contractor arrange to transport the DI pipe accordingly at his own arrangement. No any additional payment for transportation will be given to contractor. Contractors are requested to quote rate accordingly.(v) Layout plan for laying of DI pipe shall be given by EIC in writing. |
| 26 | 100mm bore |
| 27 | 150mm bore |
| 28 | M&L for laying, connecting, commissioning and testing heavy duty XLPE insulated PVC armoured sheathed 1100 volts grade 3.5 core 35 sqmm aluminium conductor laid in tranches/ducts complete all as specified and directed by Engineer-in-charge. |
| 29 | Supply and laying of DWC HDPE pipe, ISI marked in trenches or in cable ducts or fixed on walls using clamps along with all accessories like socket,bend,couplers etc confirming to IS 14930, part-II complete with fitting cutting,jointing etc of size 50 mm outer dia complete all as specified and directed by Engr-in-Charge. |
| 30 | Material and labour for earthing complete with galvanized steel electrode 600mmx600mmx6mm thick burried directly in ground vertically to a depth not less than 2.25 meter below ground level with the top edge of the earth plate not less than 1.5 meter below ground level, connected to GI strip of size 25x3 mm by means of bolts nuts and washers of galvanized iron or steel including GI medium grade protection pipe of 40 mm dia complete all as specified in electrical Plate No 5 of SSR Part 1 including excavation and earth in any type of soil charcoal, common salt all around the earth plate all as specified.Note : GI strip 25x3 mm beyond 7.5 mtr shall be measured and paid for separately |
| 31 | Supply and installation of flanged ends strainer/ dirt box of sizes 100mm with stainless steel mesh suitable for water meter for potable water supplies on up stream of water meter to avoid foreign material entering into meter complete all as specified and as directed at site by the Engineer-in-Charge. |
| 32 | Supply and installation of flanged ends strainer/ dirt box of sizes 150mm with stainless steel mesh suitable for water meter for potable water supplies on up stream of water meter to avoid foreign material entering into meter complete all as specified and as directed at site by the Engineer-in-Charge. |
| 33 | Supply and installation of flanged ends Water Meter woltman type,of size 100mm including testing and making good connection with flanged ends, with gasket rubber sheet and nut & bolts etc ISI Marked fixing in horizontal/incline/vertical position, complete all as specified and as directed at site by the Engineer-in-Charge. |
| 34 | Supply and installation of flanged ends Water Meter woltman type,of size 150mm including testing and making good connection with flanged ends, with gasket rubber sheet and nut & bolts etc ISI Marked fixing in horizontal/incline/vertical position, complete all as specified and as directed at site by the Engineer-in-Charge. |
| 35 | M & L for valves sluice flanged of class 1.0 PN supplied and installed complete of size 100 mm dia. |
| 36 | M & L for valves sluice flanged of class 1.0 PN supplied and installed complete of size 150 mm dia. |
| 37 | M&L for reflux valve (NRV)with by pass arrangement supplied and installed complete of size 100 mm dia. |
| 38 | Supply and fix Steel Wire Rope SWR rope 6mm dia PVC covered, suitable for lowring submersible pumping set ISI Marked all as specified. |
| 39 | Supplying , laying , jointing, welding and testing MS Pipe (Heavy class 'C') IS : 1239, of 100 mm sizes laid in trenches or in Horizontal/Vertical/inclined position or laying for connections for connected to out going water main DI/GI pipe line, incl fabrication work complete all as specified and as directed at site by the Engineer-in-Charge. |
| 40 | Supply & Laying of GI pipe in replacement, mediun grade ISI mark including all fittings in old/new positions in trenches/wall/floor and taking down of old gi pipe complete and making good the distributed surfaces as per existing as directed of following sizes. Excavation and earth work will be measured and paid separately. |
| 41 | 15 mm bore |
| 42 | 20 mm bore |
| 43 | 25 mm bore |
| 44 | 40 mm bore |
| 45 | 50 mm bore |
| 46 | M&L Machine pressed precast concrete interlocking paverblocks any shape and size confirming to IS 15658-2006 of 60 mm thick, M-40 Grade with grey cement and no pigments, over 25 mm thick sand cushioning complete all as specified and as directed. Note : Sand Cushioning shall be measured and paid under respective item. |
| 47 | Material and labour for painting two coat of synthetic enamel paint as per existing pattern on pipe surface/header connection including preparation of surfaces by scratching and removing the rust, applying one coat red oxide primer complete all as specified and as directed |
| 48 | M&L for fabrication (welding work) of MS Header /any size upto 300 mm MS pipe at various pump house for arresting leakages on header all as specified and directed. Please Enable Macros to View BoQ information |
| 49 | M&L for fabrication (welding work) of MS Header /any size upto 300 mm MS pipe at various pump house for arresting leakages on header all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 27, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 20 daysNov 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 23 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender