Tender For Special Repair To Offrs Md Accn P-188/2 At Perry Estate At Clement Town.
Tender Value
19.42 Lakhs
Estimated cost
Bid Submission
27 Nov 2026
17 days left
EMD
38840
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dehradun → Uttarakhand
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Offrs Md Accn P-188/2 At Perry Estate At Clement Town.
BOQ
| Sl. No. | Item Description |
| 1 | M&L old size Brick work with sub class B bricks (old size) straight or curved on plan exc 6m mean radius built in CM 1:6 incl Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed. |
| 2 | M&L for treatment for post construction Anti termite treatment of voids in masonary using chemical emulsion one litre per hole at 300 mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match existing floor/wall or surface complete all as specified and directed. |
| 3 | Taking down cement plaster any description on brick or stone walls or RCC roofs/ceiling etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed. |
| 4 | M&L for rendering 15 mm thick on fair face of brick works in CM 1:6 finished even and smooth with out using extra cement complete all as specified and directed. |
| 5 | M&L for rendering 15 mm thick in CM (1:4) on fair faces of brick or concrete surface (10mm thick in 1st layer and 5mm thick in 2nd layer) of wall,concrete and finished even and smooth with out using extra cement complete all as specified and directed. |
| 6 | M&L rendering 5 mm thick in cement mortar 1:3 on concrete surfaces of ceiling and finishing the surfaces even and smooth complete as specified and directed |
| 7 | M&L for applying 2 mm thick wall care Putty on walls and making good minor cracks, filling of holes etc. and making surfaces absolutely even and smooth, rubbing with sand paper complete all as specified and directed. |
| 8 | M&L for preparation of new plastered surfaces of walls or concrete and applying two coats of acrylic distemper over a coat of primer complete all as specified and directed. |
| 9 | M&L for preparing new plastered surfaces of walls, Facias, cornices etc and apply two coats of weather proof exterior emultion paint over a coat of primer on ht. upto ht. of 10 mtr Complete all as specified and directed. |
| 10 | M&L for preparation of new plastered surfaces of ceiling or concrete and applying two coats of acrylic distemper over a coat of primer complete all as specified and directed. |
| 11 | M&L for removal of existing treatment over wall and applying 2 mm thick wall care Putty on walls and applying two coats of acrylic distemper on wall over a coat of primer on old surfaces complete all as specified and directed. |
| 12 | M&L for complete removal of existing treatment over wall upto ht. of 10 mtr and applying two coats of weather proof exterior emultion paint over a coat of primer on wallls, concrete surfaces etc. on ht. upto 10 mtr Complete all as specified and directed. |
| 13 | M&L for preparation of old plastered surfaces of ceilings and applying two coats of acrylic distemper after rubbing ceiling with sand paper complete all as specified and directed. |
| 14 | M&L for Preparation of Newly Plastered surfaces of Wall and applying Two coats of White Wash all as specified and directed. |
| 15 | M&L Preparation of Newly Plastered surfaces of Ceiling and applying Three coats of White Wash complete all as specified and directed. |
| 16 | Taking down chowkhat or frames n exc 1.50 Sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed |
| 17 | Taking down chowkhat or frames exc 1.50 Sqm and n exc 4 Sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed |
| 18 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65 x 100mm comprising of virgin PVC polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. |
| 19 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm, modules ofelasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately) |
| 20 | S&F factory made single extruded WPC (Wood Polymer Composite) solid both side prelaminated decorative type flush door shutter of size 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. |
| 21 | S&F 35 mm thick FACTORY MADE Wire Mesh Solid WPC Pre-laminated both side DOOR SHUTTER consisting of Density 650 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company, Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (confirming as per S:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. M.S powder coated butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through both the walls of the M.S tube. Other hardwares should be fixed with 19*6mm size steel screws etc. Complete as per direction of Engineer-in-charge, manufacturer's specification & drawings. complete all as specified and directed |
| 22 | Dismantling Boarding any description fixed in any position with nails complete all as specified and directed. |
| 23 | S & F 18/19 mm thick one side prelaminated coloured WPC board for cup board shutter & frame & fixed at site with SS screws and solvent cement/ adhesive to make kitchen cabinet shutters/ cupboards complete as per manufacturer’s instructions complete all as specified and directed. Note- Colour of WPC board wiil be as approved by Engr-In-Charge/GE. |
| 24 | S & F 18/19 mm thick both side prelaminated coloured WPC board for cup board shutter & frame & fixed at site with SS screws and solvent cement/ adhesive to make kitchen cabinet shutters/ cupboards complete as per manufacturer’s instructions complete all as specified and directed. Note- Colour of WPC board wiil be as approved by Engr-In-Charge/GE. |
| 25 | S&F three track Pre coated Steel Sliding Window System fabricated from roll formed sections made of Galvanized Steel Colour Coated/ Powder Coated (Base Steel as per IS 513 “D” quality, galvanized as per IS 277 with Zinc of 120 grams/ Sq. Mtr.) with total coated thickness of 0.58 mm or Powder Coated with pure Polyester Powder up to 50-60 microns thick. Windows Section for three track external frame should be of 44 x 107mm , Section for window glass shutter should be of 36 x 50 mm, if required Section for shutter horizontal mullion should be 22mm x 60mm, The windows should be paneled with 5mm thick Plain Float glass Gaskets are to be made with Ethyl Propylene Diamine Manomer (EPDM). Corner brackets for internal and external frame made of Polypropylene. Touch lock to be provided for window shuttes Sections are to be cut to length, joined and assembled by means of corner brackets. The above Frame should be fixed to brick/ concrete masonry by using Nylon self-expanding caps and driving MS electroplated 80mm long screws into the caps through frames.Windows shall be provided with fixed Stainless steel 32gauge wire mesh/gauze of 304grade with 144 holes per square inch for mosquito proofing with the help of nut, bolt and flat iron of 20x3mm size on top and Grill made of 10mm MS Square bars welded to 25x4mm angle iron . Distance between bars should not be more than 100mm centre to centre horizontally and 4 Nos vertical bars placed equidistant . Total Grill and wire mesh unit shall be powder coated.Assembling and installation of windows and ventilators shall be all as per details shown/mentioned on drawings and as per manufacturer‟s instructions. |
| 26 | S&F Pre coated Steel window double shutter(Glazed shutter and guazed shutter) openable type prepainted section of frame 72x55mm fixed to wall or concrete surface with rawl plugs made of galvanised steel and section of shutter 47x20mm, mulion section 72x50mm (Base steel as per IS 513 \\"D\\" quality galvanized as per IS 277 with zinc of 120 gms/Sqm) glazed and wire gauge shutter prepared to receive wiremesh to the shutter (Double door shutter) with total coated thickness of 0.6mm including grills/guard bars made of 10mm square bars powder coated fixed to window frame with screws at 100mm c/c horizontal way, 4 mm thick sheet glass, 0.36mm stainless steel wire cloth ieht 1.4mm aperture and necessary fittings and all builders hardware such as handles, tower bolts & stays etc complete all as specified and as directed. |
| 27 | S & F hasp and staples, size 150 mm, safety type, stainless steel type with hinge pin including bolt to hinge plate and fixed with screws, Complete all as specified and directed |
| 28 | S&F Continuous (piano) hinges, stainless steel (AISI 316 grade), bright finish ,Width of flap (when open), 30 mm . (ISI Marked). Complete all as specified and directed |
| 29 | S & F Ball bearing runners 400 mm Telescopic (KA 5632) full extension load capacity 45 kgs complete all as specified and directed. |
| 30 | S & F D-type cabinet handles premium quality, stainless steel 304 / gloss chrome / SN finished 150 mm long matt finished complete fixed in position complete all as specified and directed. |
| 31 | S & F magnet catcher suitable for cabinets premium quality complete fixed in position as per manufacturer's instructions complete all as specified and directed. |
| 32 | S & F Stainless Steel 304 grade wire Basket of pull out type like lain / cup & saucer / bottle / multi purpose / 2-3 shelf baskets etc for kitchens of required sIze complete fixed in position all as specified and directed. |
| 33 | S&F in repair 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed. |
| 34 | S&F in repair 300 mm long Stainless Steel sliding door bolt (AISI 316 grade) bright finish of heavy quality with hasp, staple (bolt type) and fixing bolts and sliding bolts complete all as specified and directed. |
| 35 | S&F in repair floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor, over all length of cover plate 150 mm complete all as specified and directed. |
| 36 | S&F in repair for 20mm dia and 1.2 mm thick Stainless Steel Curtain Rod with & including fixing SS brackets and decorative type SS knobs on both ends incl T/D of any type old curtain rods and making good disturbed surfaces with cement mortar or putty complete all as specified and directed Note- measurement will be taken between end points of knobs. |
| 37 | S&F 100 mm long Stainless Steel butt hinges (AISI 316 grade) complete all as specified and directed. |
| 38 | S&F 150 mm size Stainless steel handles (AISI 316 grade) heavy weight of good quality complete all as specified and directed. |
| 39 | S&F 200 mm long Stainless steel barrel tower bolts (AISI 316 grade) heavy weight of good quality complete all as specified and directed. |
| 40 | S&F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4 mm fixed with stainless steel wire staples or with necessary beads complete all as specified and directed. |
| 41 | Taking down existing water proofing treatment/membrane of any type and Cleaning the surface of roof, palstered surfaces etc by roughening, picking, sweeping clean and washing down with water to remove all loose dirt etc complete all as specified. |
| 42 | M&L for water proofing treatment to roof surface complete all as specified & directed by Engr-in-Charge laid with following course of descrition below :- :- (a) Apply evenly bituminous based primer confirming to IS: 3384-1965 @ 0.30 kg/sqm. (b) APP modified bituminous membrane 3mm thick with non woven polyester core of weight not less than 3.2 to 3.5 Kg/sqm laid and bonded to the sub strata by heat process, over laps of 100mm in longitudinal and transverse direction shall be sealed/fused by flame torch application as per manufacturer instructions. membrane shall be torched into groove on vertical plane and groove sealed with cement mortar 1:3. |
| 43 | M&L for Applying 2 coats aluminium paint over APP membrane @ 0.20 Kgs/Sqm in two coats over APP membrane complete all as specified and directed. |
| 44 | M&L for preparation of existing sunken floor treatment incl plaster and removal of all debris with the following specification and sequence complete all directed by Engr-In-Chrg (a) Cleaning internal surface areas of sunken thoroughly with help of wire brushes & removing all dirt & loose materials with help of air blower by various mechanical/manual means.(b) Providing and making fillets or gola at the junction of the walls and the slabs using CM 1:4. (c) Applying 1st coat of SBR latex based waterproofing coating in the ratio as per manufacturer directions (of make-STP/Fosroc/Dr.Fixit) on floor and wall of sunken portion. (d) After 12 hours Applying 2nd coat of SBR latex based waterproofing coating in the ratio as per manufacturer directions (of make-STP/Fosroc/Dr.Fixit) on floor and wall of sunken portion. (e) Laying protection plaster 15mm th. in CM 1:4 on floor and wall. |
| 45 | M&L for applying 2 coats to liquid waterproofing compound over walls on old plastered surfaces/exposed brick surfaces of Make-Dr. Fixit Sure Seal/Asian Paints Smart care damp block 2k/Fosroc Brushbond as per manufacturer's instructions and all as directed by Engineer-in-Charge |
| 46 | Demolition of cement concrete unreinforced of any description & any thickness and in any position complete all as specified and directed. |
| 47 | M&L for PCC 1:5:10 type E-2 using 40mm graded stone aggregate as in filling of sunken floor etc and mass concrete complete all as specified and directed. |
| 48 | M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in lintels upto 1.5 m clear span, coping, benching,over chajja, roof parapet, tank staging for roof, bed block, lintel band, plinth courses etc and similar work including weathering,slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed. |
| 49 | M&L for PCC 1:2:4 type B-0 using 20 mm graded stone aggregate as in sub base flooring 25 mm thick surface finished even and rough to receive the topping layer complete all as specified and directed. |
| 50 | M&L for rendering 15 mm thick in CM 1:4 over PCC in roof to make surface smooth without using extra cement complete all as specified & directed. |
| 51 | Dismantling floor, hearth or wall tiling including cement mortar bedding etc (but not backing) and removing rubbish off the premises complete all as specified and directed. |
| 52 | M/L Double charged Vitrified Ceramic tiles 10 mm thick polished dark/light colour shade as approved by Engr-in-Charge,of size 600mmx1200mm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floors incl & over 15 mm thick screed bed in CM 1:6 complete all as specified and directed. |
| 53 | M&L Double charged Vitrified Ceramic tiles 10 mm thick polished on vertical surface of wall of size 600mm x 1200mm as in dado/skitting including 10 mm thick rendering in CM 1:4 complete all as specified and directed |
| 54 | M&L for Non skid ceramic coloured tiles of design as approved by GE 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.18 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed. |
| 55 | M&L for Non skid ceramic coloured tiles of design as approved by GE 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed. |
| 56 | M&L for glazed ceramic coloured tiles 300 x 450 x 7-8 mm thick on vertical surface such as dado /skirting / risers to steps etc jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles over and including rendering 10 mm thick in cement mortor 1:4 complete all as specified and directed. |
| 57 | M&L for 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and incl 15 mm thick screed bed in cement mortor 1:4 and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situationscomplete all as specified and directed. |
| 58 | M&L Pre-polished Baroda green marble 16-18 mm thick (table rubbed and polished) in steps, riser, jambs, pillars , window cills, cooking platforms and the like in CM 1:4 incl pointing in white cement 1:2 using marble dust with admixture of pigment to match with marble including half round moulding and making hole for gas pipe (where required) over and incl 15mm thick screed bed in CM 1:6 complete all as specified and directed |
| 59 | Ditto as item No 58 above but as in riser over 10mm thick cement plaster in CM 1:3. complete all as specified and directed |
| 60 | M&L for Vitrified tiles Endura series matt finish of size 400 mm x 400 mm x 12 mm thick set jointed and pointed in neat cement slurry in floor and cut and polished with grey cement and pigment, incl 15 mm thick screed bed in CM 1:4 complete all as specified and directed. Note-Shade,design,pattern of tile to be specified by Enginner-in-Charge. |
| 61 | Taking up & down GI steel tubing & connections including cleaning for refixing or removal to store 20mm bore of pipe complete all as specified and directed. |
| 62 | Supplying and laying of 20mm bore dia, CPVC pipes SDR 11 & plain CPVC SDR 11 fittings,and all brass fittings (MBTA/FBTA etc.) as required fixed on walls/ceiling or laid in floors, etc, incl cutting chases for concealed water tubing in brick walls if any and making good with CM 1:3 complete all as specified and directed. |
| 63 | S & F 20 mm dia GI tube medium grade galvanised with all fittings fixed complete to walls and ceilings or laid in floors complete all as specified and directed |
| 64 | Refixing old 20 mm dia GI tube medium grade galvanised with all fittings fixed complete to walls and ceilings or laid in floors complete all as specified and directed |
| 65 | S&F in repair 15 mm dia brass CP wall mixer with L bend with provision for over head shower for mixing hot and cold water screwed for iron pipe complete all as specified and directed . |
| 66 | S & F in repair 15mm dia brass CP sink mixer with swinging spout (wall mounted model) with connecting legs and wall flanges screwed down for iron pipe and fixed complete all as specified and directed . |
| 67 | S & F in repair 15mm dia brass chromium plated central hole wash hand basin mixer without PWS with 600 mm BRAIDED HOUSE hose pipe screwed down high pressure screwed for iron pipe completed all as specified and directed . |
| 68 | S&F in repair long body bib tap fancy type cast copper alloy chromium plated with crutch or butterfly handle fixed to 15 mm dia GI tube/CPVC pipe all as specified and directed. |
| 69 | S&F in repair two way angle cock fancy type cast copper alloy chromium plated with crutch or butterfly handle fixed to 15 mm dia GI tube/CPVC pipe all as specified and directed. |
| 70 | S&F in repair 15 mm fancy type stop valve/angle valve cast copper alloy chromium plated screwed high pressure with crutch or butter fly handle screwed both ends for iron or union and fixed to 15 mm GI tube complete all as specified and directed by Engineer-in-Charge. |
| 71 | S & F in repairs Brass chromium plated shower rose 110 mm size complete all as specified and directed |
| 72 | S & F in repair CP health faucet with 1m flexible tube and wall hook complete all as specified and directed. |
| 73 | S&F in repair CP brass towel rail `D’ type 60Cm long fixed to wall all as spd and directed by Engr-in-Charge |
| 74 | S&F in repair SS towel ring 125 mm dia fixed to wall all as spd and directed by Engr-in-Charge |
| 75 | S&F in repair SS toilet paper holder fixed to wall all as spd and directed by Engr-in-Charge |
| 76 | S & F in repair corner shelf assembly 300mm radius, 10mm thick toughened glass with CP guard railing with F brackets and fixing with wall screws suitable for wall corner complete all as specified and directed . |
| 77 | S&F in repair PTMT bath mirror cabinet of overall size 500mmX400mm, fixed in position complete all as specified and directed Make : Pearl/Prayag/Polytuff or equivalent |
| 78 | S&F in repair 20mm dia ball valves, high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball, screwed for iron pipes and fixed as in PVC Service tanks at any height complete all as specified and directed.. |
| 79 | S & F in repairs 20mm bore brass forged gate valves with iron flanged head screwed both ends for iron pipe and fixed.complete all as specified and directed. |
| 80 | S&F in repairs PVC connection 15mm size with PTMT nuts, of 600mm length complete all as specified and directed. |
| 81 | S&F in repairs PVC connection 15mm size with PTMT nuts, of 600mm length suitable for hot water complete all as specified and directed. |
| 82 | S&F in repair sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified. |
| 83 | S&F Stainless steel kitchen plate rack 1.0 mm thick sheet of overall size 750 x 900 x 250 mm fixed with steel screws and steel rawl plugs complete all as specified. |
| 84 | S & F in repairs, vitreous china wash basin, white, flat back, size 550x400mm with brackets, inc.cutting for fixing & pinning in ends of brackets incl waste pipe complete all as directed by Engr-in-Chrg |
| 85 | S&F in repairs viterious china squatting pan orissa pattern size 580x440mm white integal foot rest including concrete bedding & including P or S trap 100mm complete all as directed by Engr-in-Chrg |
| 86 | S & F in repairs, vitreous china wash down water closet pan (pedestal pattern), white, incl 'P' or 'S' trap and plastic water closet seat cover, black, closed pattern with flat bottom and cover & MS chromium plated or aluminised hinging device, incl HDPE flush pipe for cisterncomplete all as directed by Engr-in-Chrg |
| 87 | S&F in repair PVC low level flushing cistern (white) 10 Ltrs capacity with inlet, ball valve, float and handle internal fitting, push button operated type with and including brackets etc complete all as specified and directed.. |
| 88 | S&F in repair CP Grating doom 75/110 mm dia incl jointing with solvent cement complete all as specified and directed. |
| 89 | M&L 32mm dia bore Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc.with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed as in repairs.complete all as specified and directed. |
| 90 | S&F in repair 75/110 mm PVC (SWR) floor trap with grating including jointing with solvent cement. Complete all as specified and directed |
| 91 | Demolition and breaking up drain pipe (salt glazed ware, AC or reinforced concrete,PVC ) set in cement mortor for any size & type complete all as specified and directed. |
| 92 | M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed to walls of 75 mm bore of pipe etc complete all as specified and directed. |
| 93 | M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors or fixed to walls of 110 mm bore of pipe etc complete all as specified and directed. |
| 94 | S&F PVC (SWR) branch piece single (single Y) equal or unequal of 75 mm bore with out access door complete all as specified and directed. |
| 95 | S&F PVC (SWR) branch piece single (single Y) equal or unequal of 110 mm bore with out access door complete all as specified and directed. |
| 96 | S&F PVC (SWR) bends any radius of 75 mm bore with or without access door complete all as specified and directed. |
| 97 | S&F PVC (SWR) bends any radius of 110 mm bore with or without access door complete all as specified and directed. |
| 98 | S&F PVC (SWR) vent cowl 100 mm bore complete all as specified and directed. Please Enable Macros to View BoQ information |
| 99 | S&F PVC (SWR) vent cowl 100 mm bore complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 27, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysDec 04, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 24 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender